CdS纳米微粒有序组装体系的制备与结构研究

采用 LB膜技术制备了表面活性剂包埋的硫化镉纳米粒子多层膜 ,并利用傅里叶红外光谱、X射线光电子能谱、原子力显微镜和小角 X射线衍射对其结构进行了表征。结果表明制成的 Cd S纳米粒子 LB膜为准一维超晶格     

室温合成硫化银纳米粒子及其X射线光电子能谱表征

在常温常压下制备了硫化银纳米粒子,选用廉价的氧化银和硫粉为原料,采用多聚甲醛为还原剂,并在乙二胺体系中完成了反应。所得产物用X射线光电子能谱、X射线粉末衍射和透射电镜进行了表征。X射线粉末衍射表明：产物为单斜相的硫化银;透射电子显微镜表明：产物为直径约为100nm的棒状纳米粒子,其对应的电子衍射斑点可以指标成(120)和(303),说明产物的结晶较好;X射线光电子能谱分析表明：产物中Ag属 1价而S属-2价,它们的原子个数比为Ag：S=1：0．453。对比实验表明：多聚甲醛和无水乙二胺都起了很关键的作用;多聚甲醛起了多重作用,它既是溶剂,又是中和剂,用以除去反应的副产物多个点-甲酸,从而加速了反应的进行。     

疏水基团修饰的核-壳型NaYF_4/NaLuF_4∶Yb~(3+),Tm~(3+)纳米粒子设计制备

通过异质核诱导,利用溶剂热法在较低温度下合成了具有疏水表面的上转换发光稀土核-壳Na YF4/Na Lu F4∶20%Yb,1%Tm纳米粒子,并利用X射线衍射仪、透射电子显微镜、傅里叶变换红外吸收光谱仪以及荧光光谱仪等测试设备对其进行了结构、形貌和上转换光谱的表征。测试结果表明,纳米粒子核为立方相,壳层为六角相。核-壳型纳米粒子的尺寸平均在20 nm以下,分布较为均匀。在980 nm近红外光激发下,核-壳型纳米粒子发射出较强的紫色和紫外荧光,且发光强度明显高于同尺寸立方相Na Lu F4∶20%Yb,1%Tm纳米粒子。这表明利用异质核诱导的方法制备的核-壳型纳米粒子在生物医学领域具有更高的应用价值。     

纳米硫化锌的制备及光谱分析

采用超重力反应结晶法制备了纳米硫化锌粒子,并通过透射电子显微镜(TEM)、X射线粉末衍射仪(XRD)、X射线光电子能谱仪(XPS)、傅里叶红外光谱仪(FTIR)、紫外-可见光分光光度计(UV-Vis)和X射线能谱仪(EDX)对纳米硫化锌的形貌、结构、组成和光谱性能进行了细致分析。结果表明：超重力反应结晶法制备的纳米硫化锌粒子为球形,平均粒径为42 nm;XRD图谱表明纳米硫化锌呈现较好的闪锌矿晶型; XPS能谱表明纳米硫化锌的S(2p)的电子结合能为162.6 eV,Zn的2p_3/2,2p_1/2的电子结合能分别为1021.4, 1044.6eV。红外光谱研究表明纳米硫化锌在400～4 000cm-1范围内具有良好的红外透过率。紫外-可见光谱研究发现纳米硫化锌在200～340nm的紫外区域有较强的吸收,其禁带宽度为3.57eV。EDX能谱表明该法制备的纳米硫化锌具有较高的纯度。     

Mn和Fe过渡金属离子掺杂天然方钠石近红外发光特性

采用高温固相法制备了Na8 Al6 Si6 O24 Cl2∶M n和Na8 Al6 Si6 O24 Cl2∶Fe近红外发光材料。测定了荧光粉的X射线粉末衍射（XRD ），及室温下的光致近红外发射光谱和激发光谱。在400 nm紫外光和602 nm可见光的激发下，Na8 Al6 Si6 O24 Cl2∶M n粉末中的M n5＋（3 A2-3 T2，3 A2-1 E）发射了主发射峰位于1200 nm的近红外光谱。实验发现，M n和S共掺提高了该粉末的近红外发光强度，文中对此提出了S2--M n5＋之间的能量传递机理。在334和500 nm的激发下，Na8 Al6 Si6 O24 Cl2∶Fe粉末中的Fe2＋（3 T1-5 E）发射了主发射峰位于1000 nm的红外光谱，该现象对提高硅太阳能电池的效率可能具有积极意义。     

纳米硫化铜近红外吸收材料

采用新型超声喷雾法技术,把摩尔分数都为0.5%的Cu(NO3)2和Na2S水溶液分别作为初始反应溶液,调节溶液体系的pH值在6～8,把经过超声雾化后的Cu(NO3)2溶液逐步加入到处于强力搅拌的Na2S水溶液中,经陈化过滤后获得纳米半导体硫化铜(CuxS,1≤x≤2)粉体。分析了不同热处理温度与原料配比对获得的硫化铜纳米颗粒化学成分的影响,用X射线粉末衍射仪表征了纳米硫化铜粒子的晶相与化学组成,并采用扫描电镜观察了相应化学组成的粒子晶相形貌,测定了不同化学组分纳米硫化铜粒子从可见到近红外胶体状的吸收和透射光谱。研究表明不同化学组成的纳米硫化铜对近红外光都具有显著的吸收效应,这是由于电子在硫化铜半导体纳米粒子能带中的跃迁所致,同时这些半导体粒子对可见光具有很高透过性,但其可见光透射率随着纳米粒子从Cu2S趋向CuS而略有下降。     

铁纳米粒子的结晶形态与表面氧化膜分析

铁纳米粒子样品系采用气体蒸发法制备,用透射电子显微镜观察其结晶形态和粒径大小,采用X射线衍射、电子衍射、X射线光电子能谱和俄歇电子能谱等多种分析手段详细分析了粒子表面氧化膜的组成、结构和厚度及其稳定性,提出了铁纳米粒子组成和结构模型。结果发现铁纳米粒子本身的晶体结构与普通α-Fe是一致的,为体心立方结构,粒子表面存在约3nm厚的双层氧化膜,外面一层为γ-Fe₂O₃,厚度约为1nm。里面一层为Fe₃O₄,厚度约为2nm, 关键词：     

新型螯合磁性纳米Fe_3O_4的制备及其性能研究

采用共沉淀法制备了磁性四氧化三铁(Fe3O4)纳米粒子,并通过硅烷偶联剂对其表面进行改性,进一步在其表面偶联修饰氨基硫脲,制备了螯合磁性纳米Fe3O4粒子。利用广角X射线衍射仪(WAXD)、红外光谱仪(FTIR)、分光光度计等对磁性纳米粒子的结构和性能进行了表征。结果表明,纳米Fe3O4为反尖晶石结构,通过偶联修饰可以实现氨基硫脲在纳米粒子表面的化学改性。螯合磁性纳米粒子具有良好的分散性和磁响应性,且对多种金属离子(Pb2+、Hg2+、Zn2+、Cd2+)具有良好的螯合效果。     

核/壳结构ZnS : Mn/CdS纳米粒子的制备及发光

利用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS : Mn),利用沉淀法对ZnS ∶ Mn纳米粒子进行了不同厚度的CdS无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及光致发光(PL)光谱等手段对样品进行了表征。TEM显示粒子为球形,直径大约在14~18 nm之间。由XRD结果可以看出CdS壳层的形成过程受到了ZnS ∶ Mn核的影响,导致其结晶较差。XRD和XPS测量证明了ZnS : Mn/CdS的核壳结构。随着CdS壳层的增厚,样品的发光强度呈现一直减弱的现象。     

核/壳结构的ZnS:Mn/SiO_2纳米粒子的制备及发光性质研究

采用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS∶Mn),然后利用正硅酸乙酯(TEOS)的水解反应对其进行了不同厚度的SiO2无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及荧光发射光谱(PL)对样品的结构及光学性质进行了表征和研究。包覆SiO2壳层后,粒子的粒径明显增大并且在ZnS∶Mn纳米粒子表面可以观察到明显的SiO2壳层。XPS测试印证了ZnS∶Mn/SiO2的核壳结构。随着SiO2壳层的增厚,ZnS∶Mn/SiO2的Mn离子的发光先增强后减弱,这是因为SiO2壳层同时具有表面修饰和降低发光中心浓度这两种相反的作用。当壳层厚度(壳与核的物质的量的比)达到5时,发光效果达到最好,其强度达到未包覆样品的7.5倍。     

Direct production of carbon nanotubes decorated with Cu2O by thermal chemical vapor deposition on Ni catalyst electroplated on a copper substrate

Carbon nanotubes (CNTs) decorated with Cu₂O particles were grown on a Ni catalyst layer deposited on a Cu substrate by thermal chemical vapor deposition from liquid petroleum gas. Ni catalyst nanoparticles with different sizes were produced in an electroplating system at 45 °C using the corrosive effect of H₂SO₄ which was added to solution. These nanoparticles provide the nucleation sites for CNT growth avoiding the need for a buffer layer. The surface morphology of the Ni catalyst films and CNT growth over this catalyst was studied by scanning electron microscopy (SEM). High temperature surface segregation of the Cu substrate into the Ni catalyst layer and its exposition to O₂ at atmospheric environment, during the CNTs growth, lead to the production of CNTs decorated with about 6 nm Cu₂O nanoparticles. We used SEM to study the surface characteristics of Ni catalyst films and characteristic of grown CNTs. Raman spectroscopy, transmission electron microscopy (TEM), electron diffraction (EDX), X-ray diffraction, and X-ray photoelectron spectroscopy (XPS) revealed the formation of CNTs. The selected area electron diffraction pattern, EDX, and XPS studies show that these CNTs were decorated with Cu₂O nanoparticles. This way of fabrication is the easiest and lowest cost method.     

Synthesis, structural and optical characterization of nanocrystalline ZnS:Cu embedded in silica matrix

The synthesis of Cu doped ZnS nanoparticles inside the pore of an inorganic silica gel matrix is presented. The synthesized nanoparticles were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). X-ray diffraction pattern reveals the crystalline wurtzite phase of ZnS. The existence of silica gel in modeling morphologies of the nanoparticles was characterized using Fourier transform infrared (FTIR) spectrometer. Thickness of the silica shell was also calculated. UV- absorption spectrum shows the appearance of an absorption peak at 273 nm which confirms the blue shift as compared to that of bulk ZnS. The photoluminescence (PL) emission spectrum of the sample showed a broad band in the range 465-510 nm due to the transition from the conduction band edge of ZnS nanocrystals to the acceptor like t₂ state of Cu.     

Characterization of nanocomposite polymer electrolyte based on P(ECH-EO)

ZrO₂ nanoparticles have been prepared by poly acrylamide gel route. The synthesized nanosized ZrO₂ have been incorporated into plasticized polymer electrolyte (PPE), P(ECH-EO): LiClO₄: γ-BL system to understand the effect of ZrO₂ on the ionic conductivity. The X-ray diffraction pattern of the synthesized ZrO₂ nanoparticles reveals the crystalline phase. The X-ray diffraction patterns of P(ECH-EO) based NCPEM confirm the polymer-salt-nanoparticle complexation. The scanning electron microscope image of NCPEM confirms that the ZrO₂ nanoparticles were distributed uniformly in the polymer matrix. The presence of nano filler has increased the ionic conductivity and the maximum dc conductivity value is found to be 6.24×10⁻⁶ S cm⁻¹ at 303 K for 96(PPE): 4ZrO₂ (mol%).     

Structural, optical and electrical characterization of antimony-substituted tin oxide nanoparticles

Antimony-doped tin oxide (ATO) nanostructures were prepared using chemical precipitation technique starting from SnCl₂, SbCl₃ as precursor compounds. The antimony composition was varied from 5 to 20 wt%. The lower resistance was observed at composition of Sn:95 and Sb:05, when compared with undoped and higher doping concentration of antimony. The average crystalline size of undoped and doped tin oxide was calculated from the X-ray diffraction (XRD) pattern and found to be in the range of 30-11 nm and it was further confirmed from the transmission electron microscopy (TEM) studies. The scanning electron microscopy (SEM) analysis showed that the nanoparticles agglomerates forming spherical-shaped particles of few hundreds nanometers. The samples were further analyzed by energy dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and electrical resistance measurements.     

KZnF3:Ce3+,Tb3+纳米粒子合成与发光

采用微乳液法合成了Ce3 ,Tb3 单掺和双掺KZnF3纳米晶。分析了样品的结构与形态,结果表明,所合成的样品均为单相,颗粒粒度分布均匀。讨论了光谱特性,并与高温固相法合成的产物作了对比。研究发现,KZnF3:Ce3 纳米晶的发射光谱与体相多晶相比,最强峰位置红移约35nm;在KZnF3纳米晶双掺体系中存在Ce3 →Tb3 能量传递,尤其是Tb3 的5D4→7F5跃迁发射显著增强,有望成为一种有发展前途的绿色荧光材料。     

Synthesis and characterization of Cr doped CdS nanoparticles stabilized with polyvinylpyrrolidone

Undoped and Cr (2 and 4 at.%) doped CdS nanoparticles were synthesized in aqueous solution by simple chemical co-precipitation method using polyvinylpyrrolidone (PVP) as stabilizer. The prepared nanoparticles were examined using X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDAX), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and Fourier transform infrared spectroscopy (FTIR). XRD pattern of the nanoparticles showed cubic zincblende phase with the particle size of the order of 3-4 nm, which was in good agreement with the results obtained from TEM studies. The EDAX analysis confirmed that Cd, Cr and S elements were present in the samples and the variations between the target and actual compositions were microscopic. UV-vis DRS spectra of the samples exhibited decrease in the band gap which further attests the incorporation of Cr into CdS nanoparticles. FTIR studies revealed that the undoped as well as Cr doped CdS nanoparticles were capped by polyvinylpyrrolidone.     

Biomimetic synthesis of HgS nanoparticles in the bovine serum albumin solution

HgS nanocrystals conjugated with protein were synthesized in aqueous solution of Bovine Serum Albumin (BSA) at room temperature. The obtained HgS nanoparticles with average diameter about 20–40 nm were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), selected-area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM). The quantum-confined effect of the HgS nanoparticles is confirmed by the ultraviolet-visible (UV-vis) and photoluminescence (PL) spectrum. The rescults indicate that the BSA not only induce the nucleation, but inhibit the further growth of HgS nanoparticles. The effect of Hg²⁺ on BSA and the change of BSA conformation were studied through Fourier transform infrared (FTIR) spectroscopy and Circular dichroism (CD) spectroscopy. The possible mechanism of HgS nanoparticles growth in the BSA solution was also discussed.     

Synthesis and characterization of composite Au/TiO2 nanoparticles by laser irradiation

Composite Au/TiO₂ nanoparticles were synthesized by laser ablation of gold plate in TiO₂ sol. The nanoparticles were characterized by UV-visible spectroscopy, transmission electron microscopy, X-ray diffraction, and atomic force microscopy. The peak of surface plasmon is at 550 nm with a red shift of 30 nm compared with that of Au nanoparticles in water. Monolayers of composite Au/TiO₂ nanoparticles were obtained by dip-coating technique. The XRD pattern of Au/TiO₂ powders resembles a mixture of anatase TiO₂ and gold.     

Fabrication of novel Cu microspheres assembled with nanoparticles by a solvothermal reduction route

Copper microspheres assembled with nanoparticles have been synthesized by a simple solvothermal route at 160 °C for 24 h. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDX), transmission electron microscopy (TEM) and electron diffraction (ED) techniques. The results show that the diameters of the microspheres range from 2 to 4 μm. The formation mechanism of the morphology control over the copper microspheres assembled by nanoparticles was investigated; the use of polyvinylpyrrolidone (PVP) as the surfactant and the choice of N,N-dimethylformamide (DMF) as the reducing agent were found to be important for the final generation of copper microspheres.