PBD的掺杂对PVK:Ir(ppy)3体系发光特性的影响

从三线态激子的发光机理入手,研究了PBD作为电子传输材料对PVK:Ir(ppy)3体系的影响。实验中制备了单层器件ITO/PVK:Ir(ppy)3/PBD/Al,ITO/PVK:Ir(ppy)3:PBD/Al和双层器件,ITO/PVK:Ir(ppy)3:PBD/BCP/Al,其中PVK:Ir(ppy)3的掺杂浓度比例不变,通过改变PBD的掺杂浓度,其变化范围是PBD与PVK的质量比从0:100到20:100,制得了一系列器件,研究了它们的光致发光(PL)光谱和电致发光(EL)光谱。发现PBD这种电子传输材料的加入对器件的亮度有很大提高,当PBD与PVK质量比为10%时,器件亮度最大。     

PBD在稀土配合物与PVK混合体系电致发光中的作用

研究了PBD以较低浓度与铽配合物[Tb(m-MBA)₃phen]₂·2H₂O、PVK共掺杂体系的电致发光,制作了两类电致发光器件：ITO/PVK:Tb complex/PBD/LiF/Al,ITO/PVK：Tb complex:PBD/PBD/LiF/Al。在共掺杂的发光层中铽配合物的电致发光来源于两个途径,一个是由PVK到铽配合物的能量传递,另一个是电子和空穴在铽配合物上直接复合发光。改变PBD在发光层中的掺杂比例,制得一系列器件,通过对其光谱和亮度的研究,发现PBD在较低浓度掺杂时器件的稳定性和亮度随掺杂浓度的增加而降低。通过分析认为PBD的加入对给体(PVK)到受体(Tb complex)的能量传递效率影响较小,主要是由于PBD的加入使得电子和空穴在PVK链间的跳跃受到限制,使在由PVK、铽配合物和PBD三者掺杂组成的发光层中,注入的电子和空穴不能有效地在铽配合物上复合,这样就会减少激子在铽配合物上直接复合的概率,而造成器件的亮度和效率降低。     

电场变化对有机磷光器件中激子形成影响的研究

激子形成区域随电场变化的移动会使得有机电致发光器件(OLEDs)的效率和色度发生改变,从而影响器件的性能。文章首先制备了两种OLED器件,器件1为ITO/PEDOT∶PSS/PVK∶Ir(ppy)₃∶DCJTB (100∶2∶1 wt)/BCP(10 nm)/Alq₃(15 nm)/Al,器件2为ITO/PEDOT∶PSS/PVK∶Ir(ppy)₃(100∶2 wt)/BCP(10 nm)/Alq₃(15 nm)/Al,研究了电场强度对单层多掺杂结构器件激子形成的影响。实验发现在多掺杂发光层中,随着电压的增加,Ir(ppy)₃,PVK和DCJTB的发光均增强,PVK和DCJTB发光增强更快。对其发光机制进行分析,认为较高电场下,载流子获得较高能量,更容易形成高能量激子,产生宽禁带材料PVK的发光;另一方面,从能级结构分析DCJTB的带隙较窄, 俘获更多的载流子发光更强。同时,在器件的电致发光(EL)光谱发现在460 nm处一新的发射峰, 发光随着电压的增大相对减弱。为了研究460 nm发光的来源,制备了器件：ITO/PEDOT∶PSS/PVK∶BCP∶Ir(ppy)₃(x∶y∶2 wt)/Alq₃(15 nm)/Al, 改变x, y的比值研究发现,460 nm处的发光依然存在,推测此发光峰应与PVK及BCP之间有关。     

高效率共轭聚合物主体绿光磷光发光二极管

因电致发光效率高和器件制备工艺简单,聚合物为主体的绿色磷光电致发光成为一个研究热点.共轭聚合物的三线态能级一般低于绿色磷光材料的三线态能级,易对磷光的发光引起猝灭导致低的发光效率,所以较少被用作绿色磷光材料的主体.通过增加聚乙烯基咔唑（PVK）作为空穴传输层,获得了高发光效率的共轭聚合物聚芴（PFO）作主体绿色磷光发射,甚至高于相同条件下以PVK为主体的绿色磷光发射.究其原因,PVK的电子阻挡作用使发光中心靠近PVK与PFO的界面,界面处PVK因为其高的三线态能级增强了绿色磷光的发光.当三-（2-苯基吡啶）-Ir（Ir（ppy）₃）掺杂浓度为2％时得到了最高的亮度效率24.8 cd/A,此时的电流密度为4.65 mA/cm²,功率效率为11 lm/W,最高亮度达到35054 cd/m²,色坐标是（0.39,0.56）. 关键词： 共轭聚合物 磷光 绿光发光     

室温下磁场对基于Alq3的有机电致发光器件的影响

制备了ITO/NPB/LiF/Alq₃/LiF/Al的器件,测量了该组器件效率和亮度的磁效应.结果表明,在50 mT磁场中,当LiF缓冲层厚度为0.8 nm时,器件的效率最大增加了12.4%,磁致亮度最大变化率17%.同时,制备的磷光器件ITO/NPB/LiF/CBP:6 wt% Ir(ppy)₃/BCP/Alq₃/ LiF/Al,在50mT磁场作用下,当LiF缓冲层的厚度为0.8 nm时,器件的效率最大增加12.1%.在Alq_{3 关键词： 有机发光 磁场 效率 磁致亮度}     

体异质结有机太阳能电池性能提高的研究

制备了四种不同结构的有机太阳能电池器件,器件1 ITO/LiF/PEDOT∶PSS/MEH-PPV/C₆₀/Al、器件2 ITO/PEDOT∶PSS/MEH-PPV/C₆₀/Al、器件3 ITO/LiF/PEDOT∶PSS/MEH-PPV∶C₆₀/C₆₀/Al和器件4 ITO/PEDOT∶PSS/MEH-PPV∶C₆₀/C₆₀/Al。测量了它们的电流－电压特性,结果显示在ITO和PEDOT∶PSS之间插入一薄层LiF使得器件性能得到较大提高。其器件1的J_SC和FF比器件2的提高了74%和31%; 器件3的J_SC比器件4的提高了约40%。这主要是由于LiF层有效地抑制了空穴向阳极的传输,并且LiF层在ITO和PEDOT:PSS之间形成了良好的界面特性。因此,这种结构上的改进有效地提高了有机太阳能电池的性能。     

Influence of heterojunction interface on exciplex emission from organic light-emitting diodes under electric fields

In this paper, electroluminescence from organic light-emitting diodes based on 2-(4^′-biphenyl)-5-(4^′′-tert-butylphenyl)-1,3,4-oxadiazole (PBD) and N,N^′-diphenyl-N,N^′-bis(3-methylphenyl)-(1,1^′-biphenyl)-4,4^′-diamine (TPD) is reported. Based on the exciplex emission from the TPD/PBD interface under high electric fields, the influence of the TPD/PBD interface on exciplex emission was investigated by increasing the number of TPD/PBD interfaces while keeping both the total thickness of the TPD layer and the PBD layer constant in the multiple quantum-wells (MQW) device ITO/TPD/[PBD/TPD]_n/PBD/Al (n is the well number that was varied from 0 to 3). Our experimental data shows that exciplex emission can be enhanced by suitably increasing the well number of this kind of MQW-like device. PACS 78.60.Fi; 78.55.Kz; 73.61.Ph     

Charge tunneling and cross recombination at organic heterojunction under electric fields

Electroluminescence (EL) of bilayer organic light-emitting diodes based on N,N'-diphenyl-N,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD) and 2-(4'-biphenyl)-5-(4”-tert-butylphenyl)-1,3,4-oxadiazole (PBD) were reported. The EL spectra of bilayer device ITO/TPD/PBD/Al consist of monomolecular emission from TPD, exciplex emission and charge carriers cross recombination at the TPD/PBD interface. By varying the thickness of each organic layer while keeping the thickness of the whole device constant, three kinds of bilayer devices were fabricated and their EL and photoluminescence spectra were compared with each other, and our experimental data show that charge tunneling and cross recombination coexist at the TPD/PBD interface, and these two processes compete with each other under high electric fields.     

Ir(Fppy)_3掺杂PVK体系发光特性的研究

对蓝色磷光材料Ir(Fppy)3不同浓度掺杂PVK薄膜的光致发光(PL)和电致发光(EL)特性进行了研究。并制备了结构为ITO/PEDOT:PSS/PVK:Ir(Fppy)3/BCP/Alq3/LiF/Al的蓝色磷光有机电致发光器件。实验结果发现,磷光材料掺杂浓度不同,器件发光特性不同。当Ir(Fppy)3掺杂浓度比较低时,EL光谱中可以观察到PVK较弱的发光;当Ir(Fppy)3掺杂浓度较高时,会发生浓度猝灭;当Ir(Fppy)3掺杂浓度比较适中时,EL光谱中观察不到PVK的发光,只有Ir(Fppy)3的发光。通过I-V-L特性的比较,当掺杂浓度为4%时,器件的光电特性最好。     

Ir（PPY）3对Rubrene荧光材料的敏化性研究

最近几年,磷光器件是有机电致发光研究领域和产业化的一大热点。在实验中作者发现PVK∶PBD∶Rubrene共掺体系的发光中存在较强的PVK发光,能量传递不充分。由于一些具有重金属离子的有机物,存在强的自旋-轨道耦合作用,引入到共掺体系可以充分利用单线态和三线态的发光,从而获得高于一般有机材料器件所达到的内量子效率。为获得单色性较好的Rubrene发光,作者将磷光敏化剂Ir(ppy)3引入到PVK∶PBD∶Rubrene共掺溶液中,得到了纯正Rubrene发光,Forester能量传递也更加充分。当进一步提高Rubrene掺杂浓度以后,单色性Rubrene发光更加明显,并讨论了Ir(ppy)3所起的作用和器件的发光机理。磷光材料与有机小分子材料共掺的方法,可以有效提高器件的发光亮度及效率。     

双层有机电致发光器件中多成分激发态发射

在结构为ITO/TPD(60nm)/PBD(60nm)/Al的双层器件观察到了单体发射、激基复合物发射和电荷对复合物发射.该器件和TPD∶PBD(等摩尔)混合蒸发薄膜的光致发光光谱研究表明激基复合物仅在TPD/PBD界面形成.电致发光光谱随偏置变化，反映出各激发态的不同形成机理和不同的占有比例及载流子在器件中动态复合的过程. 关键词： 电致发光 激发态发射 激基复合物 电荷对复合物     

The effect of driving voltage on the electroluminescent property of a blend of poly(9-vinylcarbazole) and 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole

The impact of driving voltage on the electroluminescence (EL) from organic light emitting diode with ITO/PVK:PBD:TBAPF₆(10:10:1)/Al structure was analyzed by the method of Gaussian fitting. Indium tin oxide (ITO) was used as anode, poly(9-vinylcarbazole) (PVK) as polymeric host, 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole (PBD) as electron-transporting molecule, tetrabutylammonium hexafluorophosphate (TBAPF₆) as organic salt and aluminium (Al) as cathode. A broad EL has been observed and it could be attributed to the overlap of emission from four different excited state complexes, including PVK:PBD exciplex, PVK:PBD electroplex, PBD electromer and PVK electromer. The EL spectra shifted to longer wavelength with the increase of driving voltage. The ratio of PVK electromer to PVK:PBD exciplex emission intensity first declined slightly and then increased remarkably, while the relative intensity of combination of PVK:PBD electroplex and PBD electromer emission remained unchanged when the voltage was increased.     

Low voltage red phosphorescent organic light-emitting devices with triphenylphosphine oxide and 4,4′-bis(2,2′-diphenylvinyl)-1,1′-biphenyl electron transport layers

We have developed red phosphorescent organic light-emitting devices operating at low voltages by using triphenylphosphine oxide (Ph₃PO) and 4,4′-bis(2,2′-diphenylvinyl)-1,1′-biphenyl (DPVBi) electron transport layers. 4,4′-bis(N-carbazolyl)-1,1′-biphenyl (CBP) and tris-(1-phenylisoquinolinolato-C²,N) iridium(III) [Ir(piq)₃] were used as host and guest materials, respectively. Small voltage drops across the electron transport layers and direct injection of holes from 4,4′,4″-tris[N-(2-naphthyl)-N-phenyl-amino]-triphenylamine (2-TNATA) hole transport layer into the Ir(piq)₃ guests are responsible for the high current density at low voltage, resulting in a high luminance of 1000 cd/m² at low voltages of 2.8–3.0 V in devices with a structure of ITO/2-TNATA/CBP:Ir(piq)₃/DPVBi/Ph₃PO/LiF/Al.     

The use of a perylenediimide derivative as a dopant in hole transport layer of an organic light emitting device

A perylene diimide (PDI) derivative was used as a dopant in the hole transport layer (HTL) of an organic light emitting device. The HTL examined was poly (N-vinylcarbazole) (PVK) and the PDI used was N,N′-di-dodecylperylene-3,4,9,10-bis-(dicarboximide), (N-DODEPER). The structure of the device was ITO/PEDOT:PSS (70 nm)/PVK:N-DODEPER(0, 0.2, 0.4, 0.8 wt.%) (65 nm)/Alq₃ (35 nm)/LiF (1.3 nm)/Al (100 nm). 0.8 wt.% N-DODEPER presence exhibited a luminous efficiency of 7.87 cd/A and an external quantum efficiency of 0.78% at 21 mA/cm² and a power efficiency of 3l m/W at 12 mA/cm². The luminous and power efficiency values were significantly enhanced by a factor of 15 with respect to that of undoped device.     

采用瞬态电致发光研究磷光掺杂体系发光瞬时过冲的发射机理

掺杂型有机电致发光器件中载流子累积、载流子复合等物理过程的深入了解对提高器件效率和稳定性有重要作用。通过瞬态电致发光测量可以研究掺杂型有机电致发光器件内部载流子累积。对结构为: ITO/NPB(30 nm)/host: Ir(ppy)₃/BCP(10 nm)/Alq₃(20 nm)/LiF(0.7 nm)/Al(100 nm)的器件分别研究主体材料以及客体掺杂浓度变化对有机掺杂型器件瞬态发光行为的影响。实验发现,当单脉冲驱动电压关闭后,只有TAZ: Ir(ppy)₃掺杂器件出现发光瞬时过冲现象,即发光强度衰减到一定时间时突然增强;且随着客体掺杂浓度的增加,瞬时过冲强度逐渐增强。通过分析TAZ: Ir(ppy)₃掺杂器件的瞬时过冲强度对主体材料与掺杂浓度的依赖关系,进一步发现,瞬时过冲效应强度主要受限于发光层内部积累的电子载流子;TAZ: Ir(ppy)₃发光层内电子容易被客体材料分子俘获并积累,电场突变时陷阱电子容易跳跃到主体材料上并与主体材料上积累的空穴形成激子,激子能量传递到客体材料上并复合发光继而出现发光强度的瞬时过冲现象。研究发光瞬时过冲行为可探究器件发光层内的载流子和激子的动态行为,有利于指导器件的设计,从而减少积累电荷的影响,提高器件的性能。     

Hole-transporting property of a chemically hybridized poly(vinylcarbazole)-fullerene

We synthesized a star copolymer of poly(vinylcarbazole) (PVK) branched from a fullerene (C₆₀) center, and investigated its optical absorption and photoluminescence properties. The chemically hybridized PVK-C₆₀ was then employed as a hole-transporting layer of the electroluminescent device with a poly(9,9^′-dihexylfluorene-2,7-divinylene-m-phenylenevinylene-stat-p-phenylenevinylene) (CPDHFPV) emitting layer. The ITO/PVK-C₆₀/CPDHFPV/LiF/Al device showed a strong electroluminescence quenching due to a direct contact of the PVK-C₆₀ and the CPDHFPV layers. In contrast, when an additional PVK layer was introduced between the two layers, the electroluminescence was largely enhanced. The emitted light power of the ITO/PVK-C₆₀/PVK/CPDHFPV/LiF/Al device was improved by 3 times compared with the device without the PVK-C₆₀ layer.     

Influence of tetrabutylammonium hexafluorophosphate (TBAPF6) doping level on the performance of organic light emitting diodes based on PVK:PBD blend films

The effect of doping level of tetrabutylammonium hexafluorophosphate (TBAPF₆) on the performance of single-layer organic light emitting diodes (OLEDs) with ITO/PVK:PBD:TBAPF₆/Al structure were investigated where indium tin oxide (ITO) was used as anode, poly(9-vinylcarbazole) (PVK) as hole-transporting polymeric host, 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole (PBD) as electron-transporting molecule and aluminium (Al) as cathode. It was found that the doped devices underwent a unique transition at the first voltage scan as indicated by drastically increasing of current at certain applied voltage. After the transition, the threshold voltage for current injection as well as the turn-on voltage decreased significantly as compared to the undoped device. The current injection threshold voltage and turn-on voltage decreased with the increase of TBAPF₆ doping level. More importantly, a relatively low current injection threshold voltage of 3 V has been achieved by doping a significant amount of TBAPF₆ (weight ratio greater than five) in the single-layer OLED based on PVK:PBD blend films with high work function Al metal as cathode. The significant improvement was attributed to the reduction of both electron and hole injection energy barriers caused by accumulation of ionic species at the interface.     

空穴传输层对有机电致发光器件性能的影响

制备了结构为ITO/MoO₃(40 nm)/空穴传输层/CBP:Ir(ppy)₂acac(8%)(30 nm)/BCP(10 nm)/Alq₃(40 nm)/LiF(1 nm)/Al(100 nm)的器件,其中Ir(ppy)₂acac为绿色磷光染料,空穴传输层分别为TAPC(50 nm)、TAPC(40 nm)/TCTA(10 nm)、NPB(50 nm)、NPB(40 nm)/TCTA(10 nm)。通过使用4种不同结构的空穴传输层,对器件的发光性能进行了研究。结果表明,空穴传输层对器件的发光性能有较大影响。在电压为6 V、电流密度为2 mA/cm²的条件下,4种结构的器件的电流效率分别为52.5,67.8,35.6,56.6 cd/A。其原因是TAPC/TCTA及NPB/TCTA能级结构更有利于空穴对发光层的注入而且TAPC拥有较高的空穴迁移率;另外,TAPC及TCTA拥有较高的LUMO和三线态能量,可以有效地将电子和三线态激子束缚在发光层内,增加绿光染料的复合发光几率。所制备的器件均表现出良好的色坐标稳定性。     

非掺杂型高效绿色磷光有机电致发光器件

在空穴传输层TCTA与电子传输层TPBi之间引入磷光染料Ir(ppy)3超薄发光层,制备了结构为ITO/MoO_3(2 nm)/NPB(40 nm)/TCTA(10 nm)/Ir(ppy)3(xnm)/TPBi(40 nm)/LiF(1 nm)/Al(80 nm)的非掺杂磷光有机电致发光器件。通过调控非掺杂发光层的厚度,详细研究了Ir(ppy)3层厚度对器件性能的影响。实验结果表明,当非掺杂发光层厚度为0.2 nm时,器件的性能最好,器件的亮度、效率和外量子效率分别达到26 350 cd·m~(-2)、42.9 cd·A~(-1)和12.9%。研究结果表明,采用超薄的非掺杂发光层可以简化器件结构和制备工艺,获得高效率的OLED器件。     

Optical and electroluminescent properties of a number of new derivatives of divinyl dibenzothiophene sulfone

Photoluminescent and electroluminescent properties of four new bipolar linear derivatives of divinyl dibenzothiophene sulfone are studied. It is found that amorphous films of solutions, as well as films of the compounds under study in the poly(N-vinylcarbazole) matrix, have a rather high quantum yield of photoluminescence in the blue and blue-green spectrum regions. Bright blue electroluminescence is obtained in the samples with a structure of ITO/PEDOT:PSS/TPD/OC/LiF/Al using vacuum deposition of the compounds under study and in the single-layer ITO/PEDOT:PSS/PVK:OC/LiF/Al structure when applied from the solution with a threshold voltage of 2.5–3.5 V. The influence of a molecule structure on the spectra and quantum yield of fluorescence as well as on the electroluminescent properties of the compounds is shown. Results of quantum-chemical calculations in the context of the density functional theory of the structure and characteristics of main molecular orbitals are presented.