Effect of annealing on the structural, optical and electrical properties of ZnO thin films by spray pyrolysis

Zinc oxide thin films have been deposited on glass substrates at a substrate temperature of 673 K by spray pyrolysis. The samples are annealed in ambient atmosphere at various temperatures. The effect of annealing on structural, electrical, and optical properties of ZnO films has been investigated. X-ray diffraction patterns show that crystallinity of the ZnO films has been improved after annealing. The morphology of ZnO thin films is studied by atomic force microscopy. The tensile strain (compressive stress) is found to decrease with increase in annealing temperature which indicates the relaxation of tensile strain in ZnO thin films. A decrease in energy band gap is observed with increase of annealing temperature. The mechanism of blue-green luminescence of ZnO thin film has been analyzed. The resistivity is found to decrease with annealing temperature.     

Effects of post-annealing on structural, optical and electrical properties of Al-doped ZnO thin films

Aluminum-doped zinc oxide (AZO) films were deposited at 400 °C by radio-frequency magnetron sputtering using a compound AZO target. The effects of annealing atmospheres as well as hydrogen annealing temperatures on the structural, optical and electrical properties of the AZO films were investigated. It was found that the electrical resistivity varied depending on the atmospheres while annealing in air, nitrogen and hydrogen at 300 °C, respectively. Comparing with that for the un-annealed films, the resistivity of the films annealed in hydrogen decreased from 9.8 × 10⁻⁴ Ω cm to 3.5 × 10⁻⁴ Ω cm, while that of the films annealed in air and nitrogen increased. The variations in electrical properties are ascribed to both the changes in the concentration of oxygen vacancies and adsorbed oxygen at the grain boundaries. These results were clarified by the comparatively XPS analyzing about the states of oxygen on the surface of the AZO films. There was great increase in electrical resistivity due to the damage of the surfaces, when AZO films were annealed in hydrogen with a temperature higher than 500 °C, but high average optical transmittance of 80-90% in the range of 390-1100 nm were still obtained.     

Effects of annealing on structural,optical and electrical properties of Al-doped ZnO thin films

Transparent conducting oxide (TCO) thin films such as SnO2, In2O3, and Cd2SnO4, have been used extensively as sensor devices, surface acoustic wave devices, coating to heat glass windows and transparent electrodes for solid state display devices, solar cells[1,2] because of their high optical transparency in the visible range, infrared reflec-tance and low d.c. resistivity. Although SnO2 film was developed early, nowadays Sn-doped In2O3 (ITO) films are the predominant TCO thin film in …     

Thickness dependence of structural, electrical and optical behaviour of undoped ZnO thin films

Undoped ZnO thin films of different thicknesses were prepared by r.f. sputtering in order to study the thickness effect upon their structural, morphological, electrical and optical properties. The results suggest that the film thickness seems to have no clear effect upon the orientation of the grains growth. Indeed, the analysis with X-ray diffraction show that the grains were always oriented according to the c(0 0 2)-axis perpendicular to substrate surface whatever the thickness is. However, the grain size was influenced enough by this parameter. An increase in the grain size versus the thickness was noted. For the electrical properties, measurements revealed behaviour very dependent upon thickness. The resistivity decreased from 25 to 1.5×10⁻³ Ω cm and the mobility increased from 2 to 37 cm² V⁻¹ s⁻¹ when the thickness increased from 70 to 1800 nm while the carrier concentration seems to be less affected by the film thickness and varied slightly remaining around 10²⁰ cm⁻³. Nevertheless, a tendency to a decrease was noticed. This behaviour in electrical properties was explained by the crystallinity and the grain size evolution. The optical measurements showed that all the samples have a strong transmission higher than 80% in the visible range. A slight shift of the absorption edge towards the large wavelengths was observed as the thickness increased. This result shows that the band gap is slightly decreases from 3.37 to 3.32 eV with the film thickness vary from 0.32 to 0.88 μm.     

Effect of thickness on structural, optical and electrical properties of nanostructured ZnO thin films by spray pyrolysis

Transparent conducting zinc oxide thin films were prepared by spray pyrolytic decomposition of zinc acetate onto glass substrates with different thickness. The crystallographic structure of the films was studied by X-ray diffraction (XRD). XRD measurement showed that the films were crystallized in the wurtzite phase type. The grain size, lattice constants and strain in films were calculated. The grain size increases with thickness. The studies on the optical properties show that the direct band gap value increases from 3.15 to 3.24 eV when the thickness varies from 600 to 2350 nm. The temperature dependence of the electrical conductivity during the heat treatment was studied. It was observed that heat treatment improve the electrical conductivity of the ZnO thin films. The conductivity was found to increase with film thickness.     

Effect of K-doping on structural and optical properties of ZnO thin films

In this work, K-doped ZnO thin films were prepared by a sol–gel method on Si(111) and glass substrates. The effect of different K-doping concentrations on structural and optical properties of the ZnO thin films was studied. The results showed that the 1 at.% K-doped ZnO thin film had the best crystallization quality and the strongest ultraviolet emission ability. When the concentration of K was above 1 at.%, the crystallization quality and ultraviolet emission ability dropped. For the K-doped ZnO thin films, there was not only ultraviolet emission, but also a blue emission signal in their photoluminescent spectra. The blue emission might be connected with K impurity or/and the intrinsic defects (Zn interstitial and Zn vacancy) of the ZnO thin films.     

Chemically deposited copper oxide thin films: structural, optical and electrical characteristics

Thin films of copper oxide with thickness ranging from 0.05–0.45 μm were deposited on microscope glass slides by successively dipping them for 20 s each in a solution of 1 M NaOH and then in a solution of copper complex. Temperature of the NaOH solution was varied from 50–90°C, while that of the copper solution was maintained at room temperature. X-ray diffraction patterns showed that the films, as prepared, are of cuprite structure with composition Cu₂O. Annealing the films in air at 350°C converts these films to CuO. This conversion is accompanied by a shift in the optical band gap from 2.1 eV (direct) to 1.75 eV (direct). The films show p-type conductivity, 5×10⁻⁴ Ω⁻¹ cm⁻¹ for a film of thickness 0.15 μm. Electrical conductivity of this film increases by a factor of 3 when illuminated with 1 kW m⁻² tungsten halogen radiation. Annealing in a nitrogen atmosphere at temperatures up to 400°C does not change the composition of the films. However, the conductivity in the dark as well as the photoconductivity of the film increases by an order of magnitude. The electrical conductivity of the CuO thin films produced by air annealing at 400°C, is high, 7×10⁻³ Ω⁻¹ cm⁻¹. These films are also photoconductive.     

Structural,electrical and optical studies on spray-deposited aluminium-doped ZnO thin films

Thin films of zinc oxide (ZnO) were deposited on cleaned glass substrates by chemical spray pyrolysis technique using Zn(CH₃COO)₂ as precursor solution. Also, aluminium-doped thin films of ZnO were prepared by using AlCl₃ as doping solution for aluminium. The dopant concentration [Al/Zn atomic percentage (at%)] was varied from 0 to 1.5 at% in thin films of ZnO prepared in different depositions. Structural characterization of the deposited films was performed with X-ray diffraction (XRD) studies. It confirmed that all the films were of zinc oxide having polycrystalline nature and possessing typical hexagonal wurtzite structure with crystallite size varying between 100.7 and 268.6 nm. The films exhibited changes in relative intensities and crystallite size with changes in the doping concentration of Al. The electrical studies established that 1 at% of Al-doping was the optimum for enhancing electrical conduction in ZnO thin films and beyond that the distortion caused in the lattice lowered the conductivity. The films also exhibited distinct changes in their optical properties at different doping concentrations, including a blue shift and slight widening of bandgap with increasing Al dopant concentration.     

Effect of annealing on structural, optical and electrical properties of nanostructured Ge thin films

Ge thin films with a thickness of about 110 nm have been deposited by electron beam evaporation of 99.999% pure Ge powder and annealed in air at 100-500 °C for 2 h. Their optical, electrical and structural properties were studied as a function of annealing temperature. The films are amorphous below an annealing temperature of 400 °C as confirmed by XRD, FESEM and AFM. The films annealed at 400 and 450 °C exhibit X-ray diffraction pattern of Ge with cubic-F structure. The Raman spectrum of the as-deposited film exhibits peak at 298 cm⁻¹, which is left-shifted as compared to that for bulk Ge (i.e. 302 cm⁻¹), indicating nanostructure and quantum confinement in the as-deposited film. The Raman peak shifts further towards lower wavenumbers with annealing temperature. Optical band gap energy of amorphous Ge films changes from 1.1 eV with a substantial increase to ∼1.35 eV on crystallization at 400 and 450 °C and with an abrupt rise to 4.14 eV due to oxidation. The oxidation of Ge has been confirmed by FTIR analysis. The quantum confinement effects cause tailoring of optical band gap energy of Ge thin films making them better absorber of photons for their applications in photo-detectors and solar cells. XRD, FESEM and AFM suggest that the deposited Ge films are composed of nanoparticles in the range of 8-20 nm. The initial surface RMS roughness measured with AFM is 9.56 nm which rises to 12.25 nm with the increase of annealing temperature in the amorphous phase, but reduces to 6.57 nm due to orderedness of the atoms at the surface when crystallization takes place. Electrical resistivity measured as a function of annealing temperature is found to reduce from 460 to 240 Ω-cm in the amorphous phase but drops suddenly to 250 Ω-cm with crystallization at 450 °C. The film shows a steep rise in resistivity to about 22.7 KΩ-cm at 500 °C due to oxidation. RMS roughness and resistivity show almost opposite trends with annealing in the amorphous phase.     

Effect of self assembly on the nonlinear optical characteristics of ZnO thin films

In the present work, we report the third order nonlinear optical properties of ZnO thin films deposited using self assembly, sol gel process as well as pulsed laser ablation by z scan technique. ZnO thin films clearly exhibit a negative nonlinear index of refraction at 532 nm and the observed nonlinear refraction is attributed to two photon absorption followed by free carrier absorption. Although the absolute nonlinear values for these films are comparable, there is a change in the sign of the absorptive nonlinearity of the films. The films developed by dip coating and pulsed laser ablation exhibit reverse saturable absorption whereas the self assembled film exhibits saturable absorption. These different nonlinear characteristics in the self assembled films can be mainly attributed to the saturation of linear absorption of the ZnO defect states.     

The influence of using different substrates on the structural and optical characteristics of ZnO thin films

ZnO thin films with thikness d = 100 nm were deposited onto different substrates such as glass, kapton, and silicon by radio frequency magnetron sputtering. The structural analyses of the films indicate they are polycrystalline and have a wurtzite (hexagonal) structure.The ZnO layer deposited on kapton substrate shows a stronger orientation of the crystallites with (0 0 2) plane parallel to the substrate surface, as compared with the other two samples of ZnO deposited on glass and silicon, respectively.All three layers have nanometer-scale values for roughness, namely 1.7 nm for ZnO/glass, 2.4 nm for ZnO/silicon, and 6.8 nm for ZnO/kapton. The higher value for the ZnO layer deposited on kapton substrate makes this sample suitable for solar cells applications. Transmission spectra of these thin films are strongly influenced by deposition conditions. With our deposition conditions the transparent conducting ZnO layer has a good transmission (78-88%) in VIS and NIR domains. The values of the energy gap calculated from the absorption spectra are 3.23 eV for ZnO sample deposited onto glass substrate and 3.30 eV for the ZnO sample deposited onto kapton polymer foil substrate. The influence of deposition arrangement and oxidation conditions on the structural, morphological, and optical properties of the ZnO films is discussed in the present paper.     

Effect of strain on the structural and optical properties of Cu-N co-doped ZnO thin films

Polycrystalline ZnO thin films co-doped with Cu and N have been obtained by chemical bath deposition. Introduction of Cu and N causes the change of strained stress in ZnO films, which subsequently affects the structural and optical properties. The dependence of structural and optical properties of the ZnO films on lattice strained stress is investigated by XRD measurement, SEM, PL spectrum, optical reflection and Raman spectrum. The result of photoluminescence of Cu-N co-doped ZnO films indicates that the UV emission peaks shift slightly towards higher energy side with decrease in tensile strain and vise versa. The blue-shift of the absorption edge and up-shift of E2 (high) mode of the films can be observed in the optical reflection and Raman spectra.     

Study of structural, optical and electrical properties of ZnO and SnO2 thin films

The investigation of structure, optical and electrical properties of tin and zinc oxide films on glass substrates by using magnetron sputtering are carried out. X-ray data show the formation of textured tin oxides film during deposition and its transformation to SnO₂ polycrystalline film at low temperature (200 C) if the concentration of oxygen in the chamber is high (O₂ — 100%, Ar — 0%). Optimal conditions of SnO₂ polycrystalline film deposition (pressure of Ar–O₂ mixture in chamber — 2.7 Pa, concentration of O₂ — 10%) are determined. Low resistivity of as-deposited ZnO film and increasing ZnO crystallite sizes and phase volume at temperatures higher than the melting point of Zn (419.5 C) are explained by formation of conductive Zn and ZnO particle chains and their destruction, respectively.     

Effect of precursors on structure, optical and electrical properties of chemically deposited nanocrystalline ZnO thin films

Nanocrystalline ZnO thin films were chemically deposited on glass substrates using two different precursors namely, zinc sulphate and zinc nitrate. XRD studies confirm that the films are polycrystalline zinc oxide having hexagonal wurtzite structure with crystallite size in the range 25-33 nm. The surface morphology of film prepared using zinc sulphate exhibits agglomeration of small grains throughout the surface with no visible holes or faulty zones, while the film prepared using zinc nitrate shows a porous structure consisting of grains with different sizes separated by empty spaces. The film prepared using zinc sulphate shows higher reflectance due to its larger refractive index which is related to the packing density of grains in the film. Further, the film prepared using zinc sulphate is found to have normal dispersion for the wavelength range 550-750 nm, whereas the film prepared using zinc nitrate has normal dispersion for the wavelength range 450-750 nm. The direct optical band gaps in the two films are estimated to be 3.01 eV and 3.00 eV, respectively. The change in film resistance with temperature has been explained on the basis of two competing processes, viz. thermal excitation of electrons and atmospheric oxygen adsorption, occurring simultaneously. The activation energies of the films in two different regions indicate the presence of two energy levels - one deep and one shallow near the bottom of the conduction band in the bandgap.     

Effect of rf plasma nitriding time on electrical and optical properties of ZnO thin films

ZnO thin films were prepared by thermal oxidation of metallic Zn films and nitrided by an inductively coupled rf plasma. The effects of successive plasma processing cyclic times on structural and optical properties as well as electrical resistivity were examined by different characterization techniques. A small amount of nitrogen was detected at the film-substrate interface. The grain size decreased slightly as the treatment time increased. The surface roughness of examined films increased while the thickness decreased with increasing plasma treatment time. The electrical resistivity decreased about four orders of magnitude when the sample nitrided for 15 min. However, the transmittance increased as the plasma treatment time increased. The optical band gap increased from 2.76 to 3.02 eV with increasing plasma treatment time from 0 to 15 min.     

Effect of deposition parameters on structural, optical and electrical properties of nanocrystalline ZnSe thin films

This paper presents the chemical bath deposition of zinc selenide (n-ZnSe) nanocrystalline thin films on non-conducting glass substrates, in an aqueous alkaline medium using sodium selenosulphate as Se²⁻ ion source. The X-ray diffraction studies show that the deposited ZnSe material is nanocrystalline with a mixture of hexagonal and cubic phase. The direct optical band gap ‘E_g’ for the as-deposited n-ZnSe films is found to be 3.5 eV. TEM studies show that the ZnSe nanocrystals (NCs) are spherical in shape. Formation of ZnSe has been confirmed with the help of infrared (IR) spectroscopy by observing bands corresponding to the multiphonon absorption. We demonstrate the effect of the deposition temperature and reactant concentration on the structural, optical and electrical properties of ZnSe films.     

Effect of boron ion implantation on the structural, optical and electrical properties of ZnSe thin films

Zinc Selenide (ZnSe) thin films were deposited onto well cleaned glass substrates using vacuum evaporation technique under a vacuum of 3×10⁻⁵ mbar. The prepared ZnSe samples were implanted with mass analyzed 75 keV B⁺ ions at different doses ranging from 10¹² to 10¹⁶ ions cm⁻². The composition, thickness, microstructures, surface roughness and optical band gap of the as-deposited and boron-implanted films were studied by Rutherford backscattering (RBS), grazing incidence X-ray diffraction, Atomic force microscopy, Raman scattering and transmittance measurements. The RBS analysis indicates that the composition of the as-deposited and boron-implanted films is nearly stoichiometric. The thickness of the as-deposited film is calculated as 230 nm. The structure of the as-deposited and boron-implanted thin films is cubic. It is found that the surface roughness increases on increasing the dose of boron ions. In the optical studies, the optical band gap value decreases with an increase of boron concentration. In the electrical studies, the prepared device gave a very good response in the blue wavelength region.     

Structural and optical characteristics of spin-coated ZnO thin films

Zinc oxide (ZnO) thin films were deposited onto glass substrates by spin-coating method, from a precursor solution containing zinc acetate, ethanol and ammonium hydroxide. After deposition, the films were heated at a temperature of 100 °C in order to remove unwanted materials. Finally, the films were annealed at 500 °C for complete oxidation. X-ray diffraction showed that ZnO films were polycrystalline and have a hexagonal (wurtzite) structure. The crystallites are preferentially oriented with (0 0 2) planes parallel to the substrate surface. The films have a high transparency (more than 75%) in the spectral range from 450 nm to 1300 nm. The analysis of absorption spectra shows the direct nature of band-to-band transitions. The optical bandgap energy ranges between 3.15 eV and 3.25 eV.Some correlations between the processing parameters (spinning speed, temperature of post deposition heat treatment) and structure and optical characteristics of the respective thin films were established.     

Effect of deposition pressure on structural, optical and electrical properties of zinc selenide thin films

ZnSe thin films have been prepared by inert gas condensation method at different gas pressures. The influence of deposition pressure, on structural, optical and electrical properties of polycrystalline ZnSe films have been investigated using X-ray diffraction (XRD), optical transmission and conductivity measurements. The X-ray diffraction study reveals the sphalerite cubic structure of the ZnSe films oriented along the (1 1 1) direction. The structural parameters such as particle size [6.65-22.24 nm], strain [4.01-46.6×10⁻³ lin⁻² m⁻⁴] and dislocation density [4.762-18.57×10¹⁵ lin m⁻²] have been evaluated. Optical transmittance measurements indicate the existence of direct allowed optical transition with a corresponding energy gap in the range 2.60-3.00 eV. The dark conductivity (σ_d) and photoconductivity (σ_ph) measurements, in the temperature range 253-358 K, indicate that the conduction in these materials is through an activated process having two activation energies. σ_d and σ_ph values decrease with the decrease in the crystallite size. The values of carrier life time have been calculated and are found to decrease with the reduction in the particle size. The conduction mechanism in present samples has been explained, and the density of surface states [9.84-21.4×10¹³ cm⁻²] and impurity concentration [4.66-31.80×10¹⁹ cm⁻³] have also been calculated.     

Effects of electron-beam irradiation on structural,electrical, and optical properties of amorphous indium gallium zinc oxide thin films

High-energy electron-beam irradiation of indium gallium zinc oxide (IGZO) films improved the short-range arrangement. The increase in band gap was used as an indication of such improvement. X-ray diffraction confirmed that the films treated with a DC voltage of 2–4.5 kV for duration of up to 35 min are in the amorphous state or nanocrystalline phase. Higher energy electron-beam irradiation led to increased conductivity, which mainly comes from the drastic increase in electron concentration. Electron-beam treatment could be a viable route to improve the contact resistance between the source/drain and channel layer in thin-film transistor devices.