Characterization of a capillary spray cell for easy analysis of extracts of biological samples

We present a very simple electrospray unit, a capillary spray cell, for easy analysis of small (10–50 μL) sample aliquots. The sample, e.g., an unfiltered extract, is injected to a small sample cell, made of alumina and containing a short fused silica capillary mounted in its side. By the application of a 5 kV potential between the sample cell and the entrance orifice of a mass spectrometer with an atmospheric pressure interface, the sample is dragged out of the cell at a rate of a few μL/min and an electrospray is generated at the tip of the silica capillary. The capillary spray cell benefits from a high internal diameter (up to 250 μm) and very easy and inexpensive replacement of the capillary, which makes the sprayer well suited for analysis of unfiltered extracts. We demonstrate the direct analysis of extracts from plants and insects. In quantitative measurements using internal standards, a relatively high sensitivity (low ng/mL) is obtained together with good linearity (R² = 0.998) in the range of 10–1000 ng/mL. The capillary spray cell is also suited for use with field portable mass spectrometers, since no syringe pump or nebulizer gas is needed. Furthermore, the capillary spray cell is easily manufactured by most mechanical workshops.     

Monolithic molecular imprinted polymer fiber for recognition and solid phase microextraction of ephedrine and pseudoephedrine in biological samples prior to capillary electrophoresis analysis

A novel capillary electrophoresis (CE) method coupled with monolithic molecular imprinted polymer (MIP) fiber based solid phase microextraction (SPME) was developed for selective and sensitive determination of ephedrine (E) and pseudoephedrine (PE). With in situ polymerization in a silica capillary mold and E as template, the MIP fibers could be produced in batch reproducibly and each fiber was available for 50 extraction cycles without significant decrease in extraction ability. Using the MIP fiber under optimized extraction conditions, CE detection limits of E and PE were greatly lowered from 0.20 to 0.00096 μg/mL and 0.12 to 0.0011 μg/mL, respectively. Analysis of urine and serum samples by the MIP-SPME-CE method was also performed, with results indicating that E and PE could be selectively extracted. The recoveries and relative standard deviations (RSDs) for sample analysis were found in the range of 91–104% and 3.8–9.1%, respectively.     

X-ray micro-imaging by capillary optics

In this work the results on X-ray micro-imaging by means of novel polycapillary optical elements will be presented. To simulate various radiation propagation processes in both single capillary and polycapillary systems, a PolyCAD code was developed. The new experimental results on radiation redistribution by novel capillary lenses in comparison with simulated data will be reported. The images of characterized extended samples (~ 3 mm) were recorded with 6 μm resolution, the maximum provided by CCD. Polycapillary Optics CAD software X-ray tracing Imaging Confocal 02.60.Cb 02.70.-c 41.50. + h 42.15.-i 42.15.Dp 42.30.-d.     

Electrochemical detection of perchloroethylene using differential pulse voltammetry

We demonstrate the application of differential pulse voltammetry (DPV) for the electrochemical detection of perchloroethylene (PCE) on an unmodified glassy carbon electrode surface. Detection sensitivity was substantially improved using DPV, in which dechlorination was denoted by a cathodic peak observed at approximately − 0.6 V (vs Ag/AgCl). Peak current intensity was found to correlate linearly with concentration over a tested range of 0 to 10 μM. The utility of this technique was subsequently evaluated for PCE-spiked environmental samples containing either Methylobacterium adhaesivum (1 × 10⁶ cells/mL) or creek water (10% v/v). In all environmental samples, a linear dynamic range was also observed from approximately 0 to 10 μM. The limit of detection was determined to be 0.3 μM in blank buffer, 0.4 μM in bacteria-containing samples and 1.2 μM in creek water samples.     

Preconcentration of atrazine and simazine with multiwalled carbon nanotubes as solid-phase extraction disk

A sensitive and selective preconcentration method using solid-phase extraction (SPE) disk, namely multiwalled carbon nanotubes (MWCNTs) disk, is proposed for the determination of atrazine and simazine in water samples. Atrazine and simazine were extracted on MWCNTs disk and then determined by gas chromatography–mass spectrometry (GC/MS). Several parameters on the enrichment factor of the analytes were investigated. The experimental results showed that it was possible to obtain quantitative analysis when the solution pH was 5 using 200 mL of validation solution containing 0.1 μg of triazines and 5 mL of acetone as an eluent. The maximum enrichment factors for atrazine and simazine were 3900 ± 250 and 4000 ± 110, respectively when 200 mL of sample solution volume was used. Relative standard deviations for seven determinations were 6.9% (atrazine) and 3.0% (simazine) under optimum conditions. The linear range of calibration curves were 0.1 to 1 ng mL^− 1 for each analyte with good correlation coefficients. The detection limits (3S/N) were 2.5 and 5.0 pg mL^− 1 for atrazine and simazine, respectively. The proposed method was successfully applied to the determination of atrazine and simazine in environmental water samples with high precision and accuracy.     

Multiscale fibers via supramolecular self-assembly of a fully rigid,discotic aromatic aramid molecule

We synthesized a fully rigid, water soluble discotic-shaped aromatic aramid molecule, which can spontaneously self-assemble into multiscale fibers (from nano- to micro-scale in both length and diameter), depending on the molecular states (e.g., solution, liquid crystals and solid state). In diluted solution (below 0.086 g/mL), the discotic molecule tend to self-assemble into nanofibers. As the concentration increased (0.086–0.28 g/mL), it exhibits supramolecular liquid crystalline phase with microfiber texture. While, solid power under circumstance with 83% relative humidity favors the formation of rod-like shaped polymorphic crystals in macroscopic size. The unique ‘self-fiber-forming’ property of discotic molecules in different states makes them become an easy processing aramid fiber material, and also allow us to easily prepare microfilm with parallel-aligned nanofibers, which could be a promising candidate for ion conductivity material such as polymer proton exchange membrane (PEM) for fuel cell.     

A multi-syringe flow injection system for the spectrophotometric determination of trace levels of iron in waters using a liquid waveguide capillary cell and different chelating resins and reaction chemistries

A method integrating a long waveguide capillary cell with a preconcentration resin in a multi-syringe flow injection analysis (MSFIA) system for iron determination in waters was developed. The determination of iron is based on a colorimetric reaction and two reagents were tested, ferrozine and ammonium thiocyanate. A liquid waveguide capillary cell (1.0 m pathlength, 550 µm i.d. and 250 µL internal volume) with a preconcentration resin were used to improve the sensitivity of the determination. Two different preconcentration resins were also tested, Chelex 100 and NTA Superflow. The developed method employing the NTA Superflow with ferrozine colorimetric reagent provided a detection limit of 0.05 µg L^− 1 with a linear response up to 8 µg L^− 1 and a sample throughput rate of 12 per hour. The developed system presents low reagents/sample consumptions. The accuracy was assessed using a certified reference water sample.     

Determination of nicotinamide by stopped-flow injection method in pharmaceutical formulations

A simple stopped-flow injection system with spectrophotometric detection was proposed for the determination of nicotinamide (NAM) in pharmaceutical formulations. In this system cyanogen chloride formed from the combination of an acidic KSCN with the NaClO streams reacts with injected NAM to form glutaconic aldehyde. Then the product of these three components was coupled with another buffered (pH 3.5) stream of barbituric acid and directed towards the detector. A 45 s after sample injection the pump was stopped for 130 s. During this time the reactants in the flow cell were provided with the required temperature (40 °C) by placing the cell in a home made cell jacket to increase the yield of the polymethine dye product. Eventually, the absorbance of the formed pink color dye was monitored spectrophotometrically at 560 nm and NAM in the concentration range of 1.0–25.0 μg/mL (R = 0.9974 and D.L = 0.5 μg/mL) was determined. The results obtained by this method were compared statistically and agree with those obtained by the method described in the British Pharmacopoeia.     

Noise and ac impedance analysis of ion transfer kinetics at the micro liquid/liquid interface

Fluctuation analysis was utilized to determine the TEA ion transfer kinetics across the water/1,2-dichloroethane interface. The obtained data were compared with those derived from electrochemical impedance spectroscopy experiments using the same electrolytic cell. The apparent standard rate constants k_s determined by these two techniques have a similar value. The average value k_s = 0.37 cm s^− 1 is comparable with the previously reported value k_s = 0.2 cm s^− 1. The experimental approach utilizing a thick wall glass micro-capillary to fix the interface exhibits a very small stray capacitance value, proving this system to be suitable for determining the kinetics of the fast ion transfer across a liquid/liquid interface. Application of a method employing a small perturbation signal prevents polarization of the inner capillary surface by current flowing through the cell. The induced polarization of the capillary can affect ion concentration at the interface due to electroosmosis and thus make the kinetic data evaluation difficult or erroneous.     

Detection and confirmation of saxitoxin analogues in freshwater benthic Lyngbya wollei algae collected in the St. Lawrence River (Canada) by liquid chromatography–tandem mass spectrometry

The presence of cyanotoxins in benthic Lyngbya wollei algae samples collected in a fluvial lake along the St. Lawrence River, Canada, was investigated using a multi-toxins method. Hydrophilic interaction liquid chromatography (HILIC) and reverse phased liquid chromatography (RPLC) were coupled to triple quadrupole mass spectrometry (LC-QqQMS) for quantification and to quadrupole-time of flight mass spectrometry (LC-QqTOFMS) for screening and confirmation. The presence of two saxitoxin analogues, LWTX-1 and LWTX-6, was confirmed in benthic Lyngbya wollei algae samples. Concentration of LWTX-1 was between 209 ± 5 and 279 ± 9 μg g^?1. No other targeted cyanotoxin (such as anatoxin-a, nodularin, microcystin-LR, microcystins-RR and saxitoxin) was found in the samples. The presence of LWTX-6 was observed by using a screening approach based on an in-house database of cyanotoxins, an algorithm of identification and high resolution mass spectrometry measurements on the precursor and product ions. This work demonstrates the need for more research on the fate of benthic cyanotoxins in aquatic ecosystems such the St. Lawrence River.     

Change in the enzymatic dual function of the peroxiredoxin protein by gamma irradiation

PP1084 protein was exposed to gamma irradiation ranging from 5 to 500 kGy. Native PAGE showed minor structural changes in PP1084 at 5 kGy, and major structural changes at >15 kGy. Size-exclusion chromatography (SEC) showed the formation of a new shoulder peak when the protein was irradiated with 15 and 30 kGy, and a double peak appeared at 100 kGy. The results of PAGE and SEC imply that PP1084 protein is degraded by gamma irradiation, with simultaneous oligomerization. PP1084 chaperone activity reached the highest level at 30 kGy of gamma irradiation, and then, decreased in a dose-dependent manner with increasing gamma irradiation. However, the peroxidase activity significantly decreased following exposure to all intensities of gamma irradiation. The improvement of chaperone activity using gamma irradiation might be promoted by the oligomeric structures containing covalently cross-linked amino acids. Consequently, PP1084 modification using gamma irradiation could elevate chaperone activity by about 3–4 folds compared to the non-irradiated protein.     

Ruellia prostrata Poir. activity evaluated by phytoconstituents,antioxidant, anti-inflammatory,antibacterial activity,and in silico molecular functions

Ruellia prostrata Poir. has been used historically as an anti-cancer, wound healing agent and to treat gonorrhea. We aimed to determine the phytochemicals present in ethyl acetate extract of R. prostrata Poir. (EAERP). We sought to determine the antioxidant, anti-inflammatory, and antibacterial activities in vitro, and toxicity properties in vivo. We also analyzed the Prediction of Activity Spectra for Substances (PASS), physicochemical, ADMET, and drug-likeness properties of phytochemicals in EAERP. To determine phytoconstituents, preliminary phytochemical screening and GC–MS were performed, while FT-IR was used to identify functional groups. The antioxidant activity was evaluated using a DPPH scavenging assay, whereas BSA denaturation and RBC hemolysis inhibition were used to assess anti-inflammatory activity. An agar-well-diffusion assay was performed to estimate the antibacterial activity. Brine shrimp lethality bioassay and oral delivery of EAERP of single-dose were performed to determine cytotoxicity and acute toxicity, respectively. The phytochemical screening revealed the presence of phenols, triterpenoids, saponins, steroids, amino acids, and fat and fixed oils. FT-IR analysis of EAERP showed the presence of many functional groups: alcohols/phenols, carboxylic acids, aldehydes, alkanes, esters, amines, amides, aromatic hydrocarbons, sulfoxides, and alkyl halides. GC–MS revealed the presence of 39 phytoconstituents including steroids, consistent with compounds and functional groups found in preliminary screening and FT-IR. EAERP showed dose-dependent antioxidant activity with an IC₅₀ value of 21.402 µg/mL and anti-inflammatory activity with an IC₅₀ value of 20.564 µg/mL in RBC hemolysis inhibition and 21.115 µg/mL in BSA denaturation assays. EAERP also exhibited dose-related antibacterial activity. EAERP exerted cytotoxicity with an LC₅₀ value of 17.619 μg/mL and acute toxicity with an LD₅₀ value of 4095.328 mg/kg without any adverse effects. The PASS server also predicted that the phytoconstituents of EAERP have antioxidant, anti-inflammatory, and antibacterial activities with probable activity (Pa) ranging from 0.310 to 0.717. Analysis of physicochemical, ADMET, and drug-likeness properties revealed the drug-able efficacy and safety of most compounds. The findings of this study indicated that R. prostrata Poir. contains phytoconstituents with potent antioxidant, anti-inflammatory, and antibacterial activities. Taken together, our measurements suggest that R. prostrata Poir. is a prime candidate for further exploration as a potential therapeutic agent.     

Assessment of a dynamic hollow-fibre liquid phase microextraction system for human blood plasma samples

A dynamic liquid phase microextraction (LPME) system, based on hollow-fibre supported liquid membrane (SLM) extraction, was developed for extracting ionisable xenobiotics from human plasma, and its performance was evaluated (in terms of extraction efficiency, reproducibility, durability and carry-over) using nitrophenolic compounds as model analytes at concentrations of 0.1–0.5 μg mL^?1 in aqueous standards. The efficiency and repeatability were tested also on spiked human plasma. The system is non-expensive, convenient, requires minimal manual handling and enables samples with volumes as small as 0.2 mL to be extracted. For plasma samples extraction efficiencies of between 30 and 58% were achieved within 20 min, including washing steps. The limit of detection (LOD) values were in the range 0.02–0.03 μg mL^?1. The developed system can provide enrichment factors up to eight, based on the injection-to-acceptor volume ratio (in this case 0.2–0.025 mL). The same hollow-fibre membrane was used up to 8 days with no loss of efficiency. Carry-over was lower than detection limit.     

Stability-indicating HPLC method for the determination of nicardipine in capsules and spiked human plasma. Identification of degradation products using HPLC/MS

In this stability-indicating, reversed-phase high-performance liquid chromatographic method for nicardipine (NIC), forced degradation has been employed and the formed degradants were separated on a C18 (150 mm × 3.9 mm, 5 μm) analytical column using a mobile phase consisted of 70% methanol: acetic acid containing 0.01 M triethylamine with pH 4. The flow rate was 1.0 mL/min and the photodiode array detection wavelength was 353 nm. Forced degradation of the drug was carried out under acidic, basic, photolytic, and oxidative stress conditions. Chromatographic peak purity data indicated no co-eluting peaks with the main peaks. This method resulted in the detection of seven degradation products. Among these, two major degradation products from basic hydrolysis, one from oxidation by H₂O₂ and four from photolytic stress were identified by mass spectral data. A good linear response was achieved over the range of 0.5–40 μg/mL with a limit of detection (LOD) of 0.011 μg/mL and limit of quantification (LOQ) of 0.036 μg/mL. The suggested method was successfully applied for the analysis of NIC in its commercial capsules, with mean% recovery value of 100.11 ± 2.26%. The method was extended to the in vitro determination on NIC in spiked human plasma samples with mean% recovery of 99.04 ± 5.67%. The suggested method was utilized to investigate the kinetics of photolytic induced degradation.     

Trace Cd,Co, and Pb elements distribution during Sulcis coal pyrolysis: GFAAS determination with slurry sampling technique

A simple and fast method based on graphite furnace atomic absorption spectrometry (GF AAS) and slurry sampling technique (SlS) was developed to determine trace Cd, Co and Pb in high-sulphur coal (Sulcis, Italy) and coal chars derived at 600, 750 and 950 °C under N₂ atmosphere for developing a clean coal for electricity production. The proposed method was then coupled to a four-step sequential chemical extraction method for assessment of metals distribution in coaled samples. The slurries were prepared by varying sample mass (1–50 mg), volume (1–3 mL) and kind of dispersing medium (1% v/v Triton X-100 and 2 N HNO₃), and sonication time (5–30 min). Pyrolysis/atomization temperatures as well carrier gas flow rate were optimised. Pd(NO₃)₂ and NH₄H₂PO₄ were employed to stabilize Cd and Pb, respectively, in the pyrolysis stage of furnace program. The use of HNO₃ as dispersing agent was found to be effective in lowering the high level of background absorption on the Cd analytical signal produced by raw coal matrix. Conversely, coal charred samples did not show significantly level of background interferences, so that Triton X-100 dispersing agent could be used for all analytes. Calibration curve against acid-matched standards was allowed for Cd, whereas the standard addition calibration was used for Co and Pb owing to chemical matrix interferences. The precision, expressed as relative standard deviation (% RSD, n = 5), was better than 5% for Cd, Co, and Pb at 1, 10, and 15 μg L^? 1 levels, respectively. The accuracy of the analytical method was checked by analyzing a BCR No. 182 steam coal certificated reference material and the results were in good agreement with certificated and informed values. The solid detection limits (3σ_blank) were as low as 0.001 Cd, 0.01 Co, and 0.01 Pb mg kg^? 1, using 30 mg sample mass and slurry concentration of 30 m v^? 1 for Cd, and 50 mg sample mass and 50 m v^? 1 slurry concentration for Co and Pb. The content of elements in Sulcis coal was found to be 0.33 Cd, 4.0 Co, and 3.8 Pb mg kg^? 1 and mostly associated to sulphates and di-sulphides as indicated by the leaching test. Under pyrolysis conditions Cd significantly volatilised (about 64%) at temperature higher than 600 °C, whereas residue chars at 950 °C are enriched in Co and Pb up to 20%. The proposed method is suitable for routine metals monitoring in coaled samples.     

Interaction between lactose and cadmium chloride in aqueous solutions as seen by diffusion coefficients measurements

Diffusion coefficients of an aqueous system containing cadmium chloride 0.100 mol · dm⁻³ and lactose at different concentrations at 25 °C have been measured, using a conductimetric cell and an automatic apparatus to follow diffusion. The cell relies on an open-ended capillary method and a conductimetric technique is used to follow the diffusion process by measuring the resistance of a solution inside the capillaries, at recorded times. From these results and by ab initio calculations, it was possible to obtain a better understanding of the effect of lactose on transport of cadmium chloride in aqueous solutions.     

Optimization of fluorine determination via the molecular absorption of gallium mono-fluoride in a graphite furnace using a high-resolution continuum source spectrometer

The determination of fluorine using the molecular absorption of gallium mono-fluoride (GaF) at the 211.248 nm rotational line has been optimized using a commercially available high-resolution continuum source atomic absorption spectrometer with a transversely heated graphite tube furnace. The electron excitation spectrum of GaF was generated by adding 500 μg Ga per injection into the graphite tube as molecule forming reagent. Best results were obtained by applying Zr as a permanent modifier and a mixed Pd/Zr modifier, thermally pretreated before each sample injection together with the Ga reagent at 1100 °C. The use of sodium acetate and Ru(III) nitrosyl nitrate as additional modifiers injected together with the sample further improved the performance. This way a maximum pyrolysis temperature of 550 °C could be used, and the optimum molecule forming temperature was 1550 °C. Several drinking water samples, a mineral water sample, and two certified reference materials were analyzed using the standard calibration technique; the absence of potential matrix effects was verified by measuring different dilutions and spiking with known fluorine mass. The results were in good agreement with the certified values and those measured by ion selective electrode; the recovery rate for the spiking experiments was between 97% and 106%. The results show that there was no matrix influence for that kind of samples containing relatively high concentrations of Ca, Mg and chloride, which are known to cause interference in GaF molecule absorption. The limit of detection and the characteristic mass of the method were 5.2 and 7.4 pg F, respectively, and were both about a factor of two better than recently published values.     

Determination of phenolic whitening agents in cosmetics by micellar electrokinetic capillary chromatography with amperometric detection

A sensitive method for simultaneous determination of six phenolic whitening agents,including arbutin, phenol,resorcinol,hydroquinone,kojic acid,and salicylic acid in cosmetics has been developed using micellar electrokinetic capillary chromatography with amperometric detection（MECC-AD）.Effects of several factors,such as the pH value and concentration of running buffer,potential applied to the working electrode,separation voltage,and injection time were investigated to obtain optimum conditions for separation and detection.With a 75 cm long fused-silica capillary tube,well-defined separation of six phenolic compounds was achieved in 10mmol/L SDS/40 mmol/L H₃BO₃-Na₂B₄O₇ running buffer（pH 9.0）.Good linear relationship was obtained for each analyte over three orders of magnitude with correlation coefficients（r2） between 0.9985 and 0.9994,and the detection limit（S/N=3） ranged from 0.04μg/mL to 0.45μg/mL The proposed method has been successfully applied for the determination of phenolic whitening agents in real cosmetic samples with satisfactory results,providing an alternative monitoring method for cosmetics safety regulation.     

Assessment of soil quality of arable soils in Hungary using DRIFT spectroscopy and chemometrics

Nowadays, there is a great demand for precise, sensitive and adequate indicators for evaluating the quality of soils. In spite of recent developments in this field, a fast, non-destructive method for soil quality assessment has not yet been evaluated. The objective of this study was to investigate the possibility of using diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy to estimate soil quality in the form of soil quality index (SQI). A set of soil samples (n = 89) was scanned and regression was carried out using a combination of DRIFT spectroscopy and partial least-squares (PLS). The reliability of the DRIFT-PLS calibration model (n = 53) was acceptable (coefficient of determination, R² = 0.49; residual prediction deviation, RPD = 1.4) for the estimating of the SQI values. The validation of the calibration model using a validation set (n = 36) of unknown samples also resulted in good acceptability with R² = 0.68 and RPD = 1.85. The DRIFT-PLS based model could provide a rapid, cheap estimate of SQI values and subsequently of soil quality by taking into account the integrated effects of the mineralogical and organic components of the soil. This approach could be useful to monitor soil quality under conditions where the analysis of a large number of soil samples is required.     

A capillary water retention effect to improve medium-temperature fuel cell performance

We demonstrate that small and narrow hydrophilic conducting domain morphology in sulfonated aromatic membranes leads to much better fuel cell performance at medium temperature and low humidity conditions than those with larger hydrophilic domains. A comparison of three types of sulfonated poly(arylene ether sulfone)s (SPAES) with random, block, and graft architecture indicates that small hydrophilic domain sizes (< 5 nm) appear to be important in supporting water retention under low relative humidity (RH) conditions intended for medium temperature (> 100 °C) fuel cell applications. The graft copolymer outperformed both a random copolymer and multiblock copolymer at 120 °C and 35% RH fuel cell operating conditions due to capillary condensation of water within the 3–5 nm hydrophilic domains.