Synthesis and photoluminescence properties of the high-brightness Eu3+-doped Sr3Bi(PO4)3 phosphors

A series of orange reddish emitting phosphors Eu³⁺-doped Sr₃Bi(PO₄)₃ have been successfully synthesized by conventional solid-state reaction, and its photoluminescence (PL) properties have been investigated. The excitation spectra reveal strong excitation bands at 392 nm, which match well with the popular emissions from near-UV light-emitting diode chips. The emission spectra of Sr₃Bi(PO₄)₃:Eu³⁺ phosphors invariably exhibit five peaks assigned to the ⁵D₀→⁷F_J (J=0, 1, 2, 3, 4) transitions of Eu³⁺ and have dominating emission peak at 612 nm under 392 nm excitation. The luminescence intensity was enhanced with increasing Eu³⁺ content and the emission reached the maximum intensity at x=0.05 in Sr₃Bi(PO₄)₃:xEu³⁺. The energy transfer behavior in the phosphors was discussed. The Commission Internationale de lEclairage (CIE) chromaticity coordinates, the quantum efficiencies, and the decay curves of the entitled phosphors excited under 392 nm are also investigated. The experimental results indicate that the Eu³⁺-doped Sr₃Bi(PO₄)₃ phosphors are promising orange reddish-emitting phosphors pumped by near-UV light.     

Synthesis and photoluminescence properties of YVO4:Eu3+, Al3+ phosphor

The Y_0.95?xAl_xVO₄:5%Eu³⁺ (0≤x≤0.1) phosphors were successfully synthesized by solid state reaction at 900 °C for 6 h, and their luminescence properties were investigated under UV and VUV excitation. Monitoring at 619 nm, a strong broad absorption was enhanced by co-doping of Al³⁺ into the YVO₄:Eu³⁺ lattices at 256 nm under UV excitation. The VUV excitation spectra also showed the enhanced excitation bands at about 156 and 200 nm. Under 254 or 147 nm excitation, it was found that Y_0.95?xAl_xVO₄:Eu³⁺(0≤x≤0.1) phosphors showed strong red emission at about 619 nm corresponding to the electric dipole ⁵D₀^–7F₂ transition of Eu³⁺. The improvement of luminescence intensity of YVO₄:Eu³⁺ was also observed after partial substituting Y³⁺ by Al³⁺ and the optimal luminescence intensity appeared with incorporation of 2.5 mol% Al³⁺.     

White-light generation through Ce3+/Mn2+-codoped and Eu2+-doped Ba1.2Ca0.8SiO4 T-phase phosphors

Hexagonal Ba_1.20Ca_0.8?2x?ySiO₄:xCe³⁺,xLi⁺,yMn²⁺ phosphors exhibit two emission bands peaking near 400 and 600 nm from the allowed f–d transition of Ce³⁺ ions and the forbidden ⁴T₁–⁶A₁ transition of Mn²⁺ ions, respectively. The strong interaction between Ce³⁺/Mn²⁺ ions is investigated in terms of energy transfer, crystal field effect, and microstructure by varying their concentrations. They show a higher quenching temperature of 250 °C than that of a commercially used (Ba,Sr)₂SiO₄:Eu²⁺ phosphor (150 °C). Finally, mixtures of these phosphors with green-emissive Ba_1.20Ca_0.70SiO₄:0.10Eu²⁺ are tested and yielded correlated color temperatures from 3500 to 7000 K, and color rendering indices up to 95%.     

Preparation and photoluminescence properties of the Sr1.56Ba0.4SiO4:0.04Eu2+ phosphor

The Sr_1.56Ba_0.4SiO₄:0.04Eu²⁺ phosphors were prepared via a combustion reaction and following the calcination method at low temperature. The influences of the amount of the uncommonly used SrCl₂ flux, different calcination temperatures and time on the structure and the photoluminescence (PL) properties of the phosphors were investigated. Under the excitation of 450 nm blue light, the phosphor shows the intense broad emission band from 490 nm to 650 nm, and the emission peak is centered at 553 nm. The luminescence intensity of Sr_1.56Ba_0.4SiO₄:0.04Eu²⁺ was very sensitive to the crystallinity and morphology characteristics of the phosphor. The phosphor calcined at 950 °C for 3 h in 20%H₂/80%Ar atmosphere exhibits improved PL properties due to its high crystallinity and excellent morphology characteristics. The use of the SrCl₂ flux provides a novel way to improve the crystallinity of the silicates phosphors at low preparation temperature.     

Luminescent properties of Eu3+ and Sm3+ activated M2SiO4 (M=Ba,Sr and Ca) red-emitting phosphors for WLEDs

Eu³⁺ and Sm³⁺ activated M₂SiO₄ (M=Ba, Sr and Ca) red-emitting phosphors were synthesized by a solid state reaction. The results of XRD and SEM measurements show that the samples are single phase and have irregular shape. The excitation and emission spectra indicate that these phosphors were effectively excited by ultraviolet (395 nm) and blue (466 nm) light and exhibited red performance. The charge compensator R⁺ (R⁺=Li⁺, Na⁺ and K⁺) injecting into the host efficiently enhanced the luminescence intensity of the M₂SiO₄: Eu³⁺ and M₂SiO₄: Sm³⁺ phosphors. The emission intensity of M₂SiO₄: Eu³⁺ and Sm³⁺ doping Li⁺ were higher than that of Na⁺ or K⁺.     

Effect of Na+ co-dopant and activator concentration on luminescent properties of CaGa4O7:Eu3+

Two series of calcium gallate phosphors: Ca_1?xEu_xGa₄O₇ and Ca_1?2xEu_xNa_xGa₄O₇ (x=0, 0.002, 0.01, 0.02, 0.03, 0.05) were synthesized by a modified Pechini method and their optical properties at 298 and 77 K were investigated. In undoped CaGa₄O₇ upon 255 nm excitation a bluish white emission (λ_max=500 nm) followed by an afterglow of the same color lasting for 10–20 s was observed. Eu³⁺-doping quenched the host-related luminescence and the characteristic red emission of the dopant with maximum at 613 nm appeared. Its excitation spectrum consisted of a broad band assigned to ligand to metal, O^2?→Eu³⁺, charge transfer absorption and narrow lines arising from intraconfigurational transitions within the 4f⁶ states of Eu³⁺ ion. The effects of Eu³⁺ concentration and Na⁺ co-doping on the luminescence properties and decay kinetics were studied. Low temperature emission spectra showed that Eu³⁺ ions are positioned in environments of different symmetries. Their relative populations changed with the activator content. Co-doping with Na⁺ ions led to a remarkable reduction of the number of Eu³⁺ sites as well as to noticeable improvement of the luminescence brightness though it did not affect the decay time of the emission. The quantum efficiencies of singly doped CaGa₄O₇:Eu³⁺ were very low (in the range of 1–3.7%). Na⁺ co-doping improved this parameter leading to the highest efficiency of 11% for CaGa₄O₇:3%Eu³⁺,3%Na⁺.     

Photoluminescence characterization of a novel red-emitting phosphor In2(MoO4)3:Eu3+ for white light emitting diodes

The red-emitting phosphor In₂(MoO₄)₃:Eu³⁺ with cubic crystal structure was synthesized by a conventional solid-state reaction technique and its photoluminescence properties were investigated. The prepared phosphor can be efficiently excited by ultraviolet (395 nm) and blue (466 nm) light. The emission spectra of the phosphor manifest intensive red-emitting lines at 612 nm due to the electric dipole ⁵D₀→⁷F₂ transitions of Eu³⁺. The chromaticity coordinates of x=0.63, y=0.35 (λ_ex=395 nm) and x=0.60, y=0.38 (λ_ex=466 nm) are close to the standard of National Television Standard Committee values (NTSC) values. The concentration quenching of In₂(MoO₄)₃:Eu³⁺ is 40 mol% and the concentration self-quenching mechanism under 466 nm excitation was the dd intereaction. As a result of the strong emission intensity and good excitation, the phosphor In₂(MoO₄)₃:Eu³⁺ is regarded as a promising red-emitting conversion material for white LEDs.     

Synthesis and photoluminescent behavior of Eu3+-doped alkaline-earth tungstates

Eu³⁺-doped alkaline-earth tungstates MWO₄ (M=Ca²⁺, Sr²⁺, Ba²⁺) were prepared by a polymeric precursor method based on the Pechini process. The polymeric precursors were calcined at 700 °C for 2 h in order to obtain well-crystallized powders and then characterized by X-ray diffraction (XRD), thermogravimetric analysis (TG), scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy and photoluminescence spectroscopy (PL). All prepared samples showed a pure crystalline phase with scheelite-type structure confirmed by XRD. It was noted that the charge-transfer band shifted from 260 to 283 nm when calcium is replaced by strontium. However, this band was not observed for Eu³⁺-doped barium tungstate. Upon excitation at 260 nm, the emission spectra are dominated by the red ⁵D₀→⁷F₂ transition at 618 nm. By analyzing of the emission lines, it was inferred that Eu³⁺ ions occupy low symmetry sites in the host lattice. It was also found that Eu³⁺-doped SrWO₄ displays better chromaticity coordinates and greater luminescence intensity than the other samples.     

Novel EGCG assisted ultrasound synthesis of self-assembled Ca2SiO4:Eu3+ hierarchical superstructures: Photometric characteristics and LED applications

This paper reports for the first time ultrasound, EGCG assisted synthesis of pure and Eu³⁺ (1–5 mol%) activated Ca₂SiO₄ nanophosphors having self-assembled superstructures with high purity. The shape, size and morphology of the product were tuned by controlling influential parameters. It was found that morphology was highly dependent on EGCG concentration, sonication time, pH and sonication power. The probable formation mechanism for various hierarchical superstructures was proposed. The PL studies of Ca₂SiO₄:Eu³⁺ phosphors can be effectively excited by the near ultraviolet (UV) (396 nm) light and exhibited strong red emission around 613 nm, which was attributed to the Eu³⁺ (⁵D₀ → ⁷F₂) transition. The concentration quenching phenomenon was explained based on energy transfer between defect and Eu³⁺ ions, electron–phonon coupling and Eu³⁺–Eu³⁺ interaction. The Judd–Ofelt intensity parameters and radiative properties were estimated by using PL emission spectra. The photometric studies indicate that the obtained phosphors could be a promising red component for possible applications in the field of white light emitting diodes.     

Effect of Sr2+-doping on structure and luminescence properties of BaAl2Si2O8:Eu2+ phosphors

Sr²⁺ doped BaAl₂Si₂O₈:Eu²⁺ phosphor was synthesized by chemical co-precipitation method. With the increase of Sr²⁺ concentration, the phase structure of (Ba_0.965 ? xSr_xEu_0.035)Al₂Si₂O₈ changes from hexagonal phase to monoclinic phase owing to large activation energy in SrAl₂Si₂O₈ system. (Ba_0.965 ? xSr_xEu_0.035)Al₂Si₂O₈ phosphor exhibits a broad blue band peaking at 425 nm due to the 4f⁶5d–4f⁷(⁸S_7/2) transition of Eu²⁺ ions. The emission intensity increases, accompanied by the blue shift of emission maximum from 459 to 417 nm with the Sr²⁺ doping concentration increasing. The optimal concentration of Sr²⁺ ion is 40%, and the phosphor shows high color stability in CIE chromaticity diagram. The result indicates that Sr²⁺ doped phosphor not only can enhance the relative intensity but also can adjust the chromaticity coordinate.     

Synthesis and luminescence properties of green phosphors Ca6Sr4(Si2O7)3Cl2:Eu2+ for white light emitting diodes

Divalent europium-activated chlorosilicate Ca₆Sr₄(Si₂O₇)₃Cl₂:Eu²⁺ phosphors were synthesized by a conventional solid-state reaction under reductive atmosphere. These phosphors can be efficiently excited by UV–visible light from 320 to 420 nm, which matches that of a near UV-emitting InGaN chip. Under the 360 nm excitation, Ca₆Sr_3.97(Si₂O₇)₃Cl₂:0.03Eu²⁺ phosphor shows a strong and broad emission centering at 515 nm, which is attributed to the 5d→4f transition of Eu²⁺ ion. The mechanism of concentration quenching was determined to be the dipole–dipole interaction and the critical energy-transfer distance of Eu²⁺ was calculated as 3.31 nm. The CIE chromaticity coordinates of Ca₆Sr_3.96(Si₂O₇)₃Cl₂:0.03Eu²⁺ phosphor are (0.127, 0.770) according to the emission spectrum. It can be expected that Ca₆Sr₄(Si₂O₇)₃Cl₂:Eu²⁺ phosphor is a promising candidate as the green component for near-ultraviolet InGaN-based white LED.     

Nonradiative energy transfer from Mn2+ to Eu3+ in K2CaP2O7:Mn2+,Eu3+ phosphor

A series of color tunable phosphors K₂Ca_1?x?yP₂O₇:xMn²⁺, yEu³⁺ are synthesized by solid state reaction method. The energy transfer phenomenon from Mn²⁺ to Eu³⁺ has been observed in the Mn²⁺/Eu³⁺ codoped non-magnetic K₂CaP₂O₇ host, which was confirmed by PL spectra and decay curves. The Mn²⁺→Eu³⁺ energy transfer is controlled by quadrupole–quadrupole interaction between sensitizer and activator. The maximum efficiency of energy transfer is estimated to be 33% with x=0.125 and y=0.03 in K₂Ca_1?x?yP₂O₇:xMn²⁺, yEu³⁺ phosphor. The phosphors can emit light from green to yellow and eventually to orange under 400 nm excitation by changing the Mn²⁺/Eu³⁺ content ratio, indicating that K₂CaP₂O₇: Mn²⁺, Eu³⁺ would be potential candidates for use in lighting and displays applications.     

Synthesis,characterization and studies of radiative properties on Eu3+-doped ZnAl2O4

Eu³⁺-doped ZnAl₂O₄ phosphors were successfully synthesized in air atmosphere at 900 °C. The phosphors were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), thermally stimulated luminescence (TSL) and photoluminescence (PL) techniques. The average particle size of the system as determined from SEM was found to be 100–150 nm (for samples annealed at 900 °C). PL spectra of the doped phosphors showed emission peaks corresponding to Eu³⁺ ions. Lifetime studies revealed Eu³⁺ ions to be in two different sites. The asymmetric ratio (I₆₁₆/I₅₉₂) was observed to be about 3.75. This suggested that Eu³⁺ ion entered the host mainly substituting Al³⁺ site distorting the local environment and is partly located on surface of the phosphors. A prominent glow peak at 430 K was observed in the TSL of γ-irradiated Eu³⁺-doped ZnAl₂O₄ phosphors. Trap parameters for this peak have been determined and the probable mechanism for the glow peak is proposed. CIE chromaticity coordinates for the system were evaluated. It was observed that, the system could be employed as a potential red emitting phosphor. Commercial utility of the phosphor was investigated by comparing it with commercial red phosphor. The PL intensity of the as prepared phosphors was 63% of that of the commercial phosphor. Apart from this, various radiative properties such as the Judd–Ofelt intensity parameters, spontaneous emission probabilities, luminescence branching ratios, radiative lifetimes and quantum efficiency were evaluated for the system.     

Luminescent properties of Eu2+and Dy3+ ions in Ba4Al2O7 phosphor for solid state lighting

In this paper we report the combustion synthesis of rare earth (RE=Eu, Dy) doped Ba₄Al₂O₇ phosphors. Prepared phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), CIE color co-ordinates and their photoluminescence (PL) properties were also investigated. In case of Ba₄Al₂O₇: Eu²⁺, the emission spectra show unique band centered at 495 nm, which corresponds to the 4f⁶5d¹→4f⁷ transition of Eu²⁺, and PL emission spectra of Dy³⁺ ion under 348 nm excitation give two bands centered at 478 nm (blue) and 575 nm (yellow), which originate from the transitions of ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 of Dy³⁺, respectively. The results indicate that the Eu²⁺ and Dy³⁺ activated Ba₄Al₂O₇ phosphor could find application in solid state lighting.     

Luminescent properties of red-emitting LiSr4B3O(9−3x/2)Nx:Eu2+ phosphor for white-LEDs

An Eu²⁺-activated oxynitride LiSr_(4?y)B₃O_(9?3x/2)N_x:yEu²⁺ red-emitting phosphor was synthesized by solid-state reactions. The synthesized phosphor crystallized in a cubic system with space group Ia–3d. The LiSr₄B₃O_(9?3x/2)N_x:Eu²⁺ phosphors exhibited a broad red emission band with a peak at 610 nm and a full width at half maximum of 106 nm under 410 nm excitation, which is ascribed to the 4f⁶5d¹→4f⁷ transition of Eu²⁺. The optimal doped nitrogen concentration was observed to be x=0.75. The average decay times of two different emission centers were estimated to be 568 and 489 ns in the LiSr_3.99B₃O_8.25N_0.5:0.01Eu²⁺ phosphors, respectively. Concentration quenching of Eu²⁺ ions occurred at y=0.07, and the critical distance was determined as 17.86 Å. The non-radiative transitions via dipole–dipole interactions resulted in the concentration quenching of Eu²⁺-site emission centers in the LiSr₄B₃O₉ host. These results indicate LiSr₄B₃O_(9?3x/2)N_x:Eu²⁺ phosphor is promising for application in white near-UV LEDs.     

100 MeV Si8+ ion induced luminescence and thermoluminescence of nanocrystalline Mg2SiO4:Eu3+

Nanoparticles of Mg₂SiO₄:Eu³⁺ have been prepared by the solution combustion technique and the grain size estimated by PXRD is found to be in the range 40–50 nm. Ionoluminescence (IL) studies of Mg₂SiO₄:Eu³⁺ pellets bombarded with 100 MeV Si⁸⁺ ions with fluences in the range 1.124–22.48×10¹² ions cm^?2 are carried out at IUAC, New Delhi, India. Five prominent IL bands with peaks at 580 nm, 590 nm, 612 nm, 655 nm and 705 nm are recorded. These characteristic emissions are attributed to the luminescence centers activated by Eu³⁺ cations. It is found that IL intensity decreases rapidly in the beginning. Later on, the intensity decreases slowly with further increase of ion fluence. The reduction in the ionoluminescence intensity with increase of ion fluence might be attributed to degradation of Si–O (ν₃) and Si–O (2ν₃) bonds present on the surface of the sample. The red emission with peak at 612 nm is due to characteristic emission of ⁵D₀→⁷F₂ of the Eu³⁺ cations. Thermoluminescence (TL) studies of Mg₂SiO₄:Eu³⁺ pellets bombarded with 100 MeV Si⁸⁺ cations with fluences in the range 5×10¹¹ ions cm^?2 to 5×10¹³ ions cm^?2 are made at RT. Two prominent and well resolved TL glows with peaks at ～220 °C and ～370 °C are observed. It is observed that TL intensity increases with increase of ion fluence. This might be due to creation of new traps during swift heavy ion irradiation.     

Enhanced red fluorescence in Sr2Si1−xGexO4:Eu3+ phosphors by the substitution of Si by Ge for white light emitting diodes

Eu³⁺-doped Sr₂Si_1?xGe_xO₄ (x=0–1) phosphors have been prepared by the high temperature solid-state reaction method. The luminescent properties of these phosphors were investigated. Red fluorescence of Eu³⁺ is enhanced gradually in the samples with increasing substitution of Si by Ge upon the excitation of 393 nm light. The intensity is increased by 50% with full substitution of Si by Ge. These results are originated from the structural changes and the phonon energy reduction in the samples due to the substitution of Si by Ge. The CIE chromaticity coordinates of the phosphors vary slightly around (0.62, 0.37) and all are in the red color region. The results indicate that these phosphors could be promising red phosphors for white light emitting diodes.     

Structure dependent luminescence characterization of green–yellow emitting Sr2SiO4:Eu2+ phosphors for near UV LEDs

This paper reports on the luminescence properties of mixtures of α- and β-(Sr_0.97Eu_0.03)₂SiO₄ phosphors. These phosphors were prepared by 3 different synthesis techniques: a modified sol–gel/Pechini method, a co-precipitation method and a combustion method. The structural and optical properties of these phosphors were compared to those of solid state synthesized powders. The emission spectra consist of a weak broad blue band centered near 460 nm and a strong broad green–yellow band centered between 543 and 573 nm depending on the crystal structure. The green–yellow emission peak blue-shifts as the amount of β phase increases and the photoluminescence emission intensity and quantum efficiency of the mixed phase powders is greater than those of predominant α-phase powders when excited between 370 and 410 nm. Thus, (Sr_1?xEu_x)₂SiO₄ with larger proportion of the β phase are more promising candidates than single α-phase powders for use as a green–yellow emitting phosphor for near UV LED applications. Finally the phosphors prepared by the sol–gel/Pechini method, which have larger amount of β phase, have a higher emission intensity and quantum efficiency than those prepared by co-precipitation or combustion synthesis.     

A potential red-emitting phosphor with high color-purity for near-UV light emitting diodes

New red tungstates phosphors, Na₅La_1?xLn_x(WO₄)₄ (Ln = Eu, Sm) and Na₅Eu_1?xSm_x(WO₄)₄, were prepared by solid-state reaction technique. And their structure and photo-luminescent properties were investigated. The introduction of Sm³⁺ broadened the excitation band around 400 nm of the phosphors, and strengthened the red emission. And the possible energy transfer process from Sm³⁺ to Eu³⁺ is discussed. The single red LED was fabricated by combining InGaN chip with Na₅Eu_0.94Sm_0.06(WO₄)₄ as red phosphor, intense red light can be observed by naked eyes. Then the phosphor Na₅Eu_0.94Sm_0.06(WO₄)₄ may be a good candidate for red component of near-UV InGaN-based W-LEDs, because of efficient red-emitting with broadened absorption around 400 nm and appropriate CIE chromaticity coordinates (x = 0.65, y = 0.34).     

Novel red phosphor of double perovskite compound La2MgTiO6:xEu3+

A novel red phosphor La₂MgTiO₆:xEu³⁺ was successfully synthesized by the conventional solid state method. Excited by ultraviolet (395 nm) and blue (465 nm) light, La₂MgTiO₆:xEu³⁺ exhibits intense red emission. Due to the lack of inversion symmetry at the doping sites, the dominant emission peak is from the transition ⁵D₀→⁷F₂. Non-radiative transitions were demonstrated to be from dipole–dipole interactions and the critical distance was estimated to be ～9.19 Å. When Eu³⁺ ions' concentration reaches 15%, the emission intensity is about three times higher than that of the conventional phosphor Y₂O₃:Eu³⁺. The Commission International de L'Eclairage chromaticity coordinate was calculated to be x=0.657 and y=0.343. All the results indicate that La₂MgTiO₆:xEu³⁺ has superior luminescence properties.