锰活性物质负载Ti掺杂SiO2纳米管复合催化剂的制备及其NH3-SCR反应活性

利用溶胶-凝胶法以及共缩聚反应合成得到了新型的Ti掺杂SiO₂纳米管（TiSNTs）。然后,利用共沉淀的方法在该催化剂上负载了不同Mn含量的Mn/TiSNTs复合催化剂。当Si与Ti的物质的量之比超过5时,可以看到形成了很清楚的蠕虫状形貌。NH₃-TPD（氨气程序升温脱附）测试结果显示掺杂到SiO₂骨架中的Ti极大增强了催化剂的酸性位点而且提高了NH₃在催化剂表面的吸附量和氨选择性催化还原（NH₃-SCR）的活性。同时,H₂-TPR（氢气程序升温还原）测试结果显示Ti掺杂增强了催化剂的氧化还原能力和储氧容量。NH₃还原NO_x的SCR结果说明当Si与Ti的物质的量之比为10的时候,Mn/Ti（10） SNT催化剂显示了优异的催化活性,在温度范围为135~325℃时NO转化率超过90%。     

锰活性物质负载Ti掺杂SiO_2纳米管复合催化剂的制备及其NH_3-SCR反应活性（英文）

利用溶胶-凝胶法以及共缩聚反应合成得到了新型的Ti掺杂SiO_2纳米管(Ti SNTs)。然后,利用共沉淀的方法在该催化剂上负载了不同Mn含量的Mn/TiSNTs复合催化剂。当Si与Ti的物质的量之比超过5时,可以看到形成了很清楚的蠕虫状形貌。NH_3-TPD(氨气程序升温脱附)测试结果显示掺杂到SiO_2骨架中的Ti极大增强了催化剂的酸性位点而且提高了NH_3在催化剂表面的吸附量和氨选择性催化还原(NH_3-SCR)的活性。同时,H_2-TPR(氢气程序升温还原)测试结果显示Ti掺杂增强了催化剂的氧化还原能力和储氧容量。NH_3还原NO_x的SCR结果说明当Si与Ti的物质的量之比为10的时候,Mn/Ti(10)SNT催化剂显示了优异的催化活性,在温度范围为135~325℃时NO转化率超过90%。     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

水热老化对Cu改性的W/CeTi催化剂NH3-SCR性能的影响

采用浸渍法制备了CuW/CeTi和W/CuCeTi催化剂,考察了催化剂中Cu的不同作用方式对氨气选择性催化还原NO_x （NH₃-SCR）反应脱硝性能的影响。新鲜的CuW/CeTi和W/CuCeTi在低温下显示出优异的活性。经过800℃、10 h水热老化后,W/CuCeTi表现出比CuW/CeTi更优异的脱硝性能,证明W/CuCeTi具有更高的水热稳定性。通过透射电子显微镜（TEM）、X射线衍射（XRD）、拉曼光谱（Raman）、N₂物理吸附-脱附、X射线光电子能谱（XPS）、氨气程序升温脱附（NH₃-TPD）和氢气程序升温还原（H₂-TPR）表征,发现Cu的掺杂形成的Cu-O-Ce结构能够提高CeTi的抗烧结能力,同时削弱W-CeO₂相互作用,抑制老化过程中Ce₂（WO₄）₃物质的形成,使W/CuCeTi表现出更优异的水热稳定性。     

ZrCdOx/SAPO-18双功能催化剂催化CO2加氢合成低碳烯烃性能

采用并流共沉淀法制备了不同Zr/Cd原子比（n_Zr/n_Cd）的ZrCdO_x金属氧化物，并与水热法制备的不同硅铝比（n_SiO2/n_{Al2O3）的片状SAPO-18分子筛物理混合制得ZrCdOx/SAPO-18双功能催化剂，研究了其催化CO2加氢直接合成低碳烯烃性能。采用透射电子显微镜（TEM）、X射线衍射（XRD）、N2吸附-脱附、CO2程序升温脱附（CO2-TPD）、NH3程序升温脱附（NH3-TPD）和X射线光电子能谱（XPS）对催化剂进行了分析。与单一ZrO2相比，引入CdO使得ZrCdOx比表面积下降，当nZr/nCd=8时制备的Zr8Cd1氧化物呈现出无定形小颗粒状，Zr与Cd之间较强的协同作用使得ZrCdOx氧化物产生了更多的氧空位，有利于CO2的吸附活化。通过对Zr8Cd1金属氧化物与SAPO-18（硅铝比0.1）的质量比、工艺反应温度、压力和空速对催化性能影响的考察，获得了最佳反应条件。研究还发现，当SAPO-18的硅铝比从0.1降为0.01时，Brø；nsted酸含量降低，产物中烯烃/烷烃物质的量之比从18.6提高至37.2，但副产物CO含量迅速增加，低碳烯烃时空收率明显下降。}     

Mn1-x(Li,Ti)xCo2O4尖晶石型复合氧化物的制备、表征与催化性能

用柠檬酸配位燃烧法合成了Mn_1-x(Li,Ti)_xCo₂O₄系列尖晶石型复合氧化物催化剂，使用FTIR和XRD方法对催化剂结构进行表征，通过程序升温氧化反应(TPO)技术对这些催化剂在模拟柴油机尾气条件下进行同时消除NO_x和柴油碳黑反应的活性评价。结果表明，掺杂Li或Ti后的Mn_1-x(Li,Ti)_xCo₂O₄系列催化剂仍然保持了完整的尖晶石型复合氧化物结构，这些催化剂对同时消除柴油机尾气中的碳黑颗粒和NO_x具有良好的催化性能，其中Li或Ti的掺杂量为x=0.05较佳，结合碳黑燃烧与NO_x还原总的催化效果，Mn_0.95Li_0.05Co₂O₄具有最好的催化活性。     

Zr 改性MnOx/MWCNTs催化剂的结构特征与低温SCR活性

以ZrO（NO₃）₂·2H₂O为前驱体对多壁碳纳米管（MWCNTs）进行了改性并负载MnO_x制备了MnO_x/ZrO₂/MWCNTs 催化剂. 考察了Zr 对催化剂低温选择性催化还原（SCR）反应活性的影响,并通过多种分析手段对催化剂的结构进行了表征. 结果表明Zr 的添加对催化剂的低温SCR活性具有显著的促进作用,当Zr 负载量为30%时,催化剂活性最佳. X射线衍射（XRD）、拉曼（Raman）光谱、透射电镜（TEM）、N₂吸附-脱附的表征结果分析表明,适量的Zr 改性促进了MnO_x在载体表面的分散,增强金属氧化物与MWCNTs 之间的作用,也能增加催化剂的比表面积、孔容和孔径. X 射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和NH₃程序升温脱附（NH₃-TPD）的分析结果则显示,Zr 能提高催化剂表面化学吸附氧浓度,促进Mn³⁺转化为Mn⁴⁺,从而使催化剂表面的活性位点增多,氧化还原能力增强,同时还提高了催化剂表面酸性位点的数量和强度,促进了NH₃的吸附,是MnO_x/ZrO₂/MWCNTs 催化剂低温SCR活性提高的主要原因.     

助剂对Ni/γ-Al2O3催化剂上多环烃JP-10重整制氢反应性能的影响

采用等体积浸渍法制备了碱金属Na、碱土金属Mg以及稀土金属Ce改性的15% Ni-5% M/γ-Al₂O₃镍基负载型催化剂（标记为NMA,M=Na、Mg、Ce）。通过XRD （X射线衍射）、N₂吸附-脱附、H₂-TPR （H₂-程序升温还原）、TEM （透射电镜）、NH₃-TPD （NH₃-程序升温脱附）、TG （热重）和拉曼光谱技术对催化剂的物相、织构、表面性质等进行了表征分析,并在微通道反应器内研究了多环烃挂式四氢双环戊二烯（JP-10）催化重整制氢性能。结果表明,不同助剂的加入均在一定程度上提高了Ni/γ-Al₂O₃（NA）催化剂的活性和抗积碳性能。其中,NNaA催化剂的表面活性镍物种的浓度最高,颗粒尺寸最小,且其表面总酸量较低,在高温重整反应中对活性组分镍的抑制聚集作用最为明显,从而使其获得最佳的改性效果。在常压、750℃、水碳比（S/C）为2.4、重时空速（WHSV）为472 h^-1条件下,NNaA催化剂上JP-10的转化率和H₂选择性分别可达82.9%和73.3%,而积碳量仅为0.53 mg·g_feed^-1。反应后该催化剂的积碳多为丝状碳,而其他催化剂的积碳多为无定形碳。     

热扩散法制备MoO3/SiO2催化草酸二甲酯和苯酚酯交换反应

采用热扩散法（TS）和等体积浸渍法制备了MoO₃/SiO₂催化剂用于草酸二甲酯和苯酚酯交换反应.结果表明,热扩散法制备的10%MoO₃/SiO₂-TS催化剂较等体积浸渍法制备的10%MoO₃/SiO₂-C催化剂具有更好的催化性能.运用X射线衍射、Raman光谱、X射线光电子能谱分析、吡啶吸附红外光谱、NH₃程序升温脱附等手段对催化剂进行了表征,发现虽然两种方法制备的催化剂都只有弱Lewis酸中心,钼均以氧化钼单体形式存在,未形成解离和聚合,但是10%MoO₃/SiO₂-TS催化剂较10%MoO₃/SiO₂-C催化剂表面钼含量更高且MoO₃分散得更好.在苯酚用量为0.2mol,10%MoO₃/SiO₂-TS催化剂用量为1.2g,反应温度为180℃,草酸二甲酯与苯酚的摩尔比为2,反应时间为4h的优化条件下,苯酚转化率可达70.9%,甲基苯基草酸酯和草酸二苯酯的收率分别达63.1%和7.7%.     

Ni/SiO2-ZrO2催化剂焙烧温度对其催化愈创木酚加氢脱氧性能的影响简

采用化学沉淀法合成了SiO₂-ZrO₂复合氧化物载体,并以浸渍法制备了Ni/SiO₂-ZrO₂双功能催化剂,考察了焙烧温度对催化剂结构及其催化愈创木酚加氢脱氧制环己烷性能的影响. 结果表明,经500℃焙烧催化剂的加氢脱氧活性最高,在Ni金属中心和SiO₂-ZrO₂载体材料的协同作用下,愈创木酚转化率为100%,环己烷选择性为96.8%. 对催化剂进行N₂物理吸附、H₂化学吸附、X射线衍射分析、H₂程序升温还原、NH₃程序升温脱附与Raman光谱等表征后发现,合成的SiO₂-ZrO₂为无定形的酸碱两性氧化物;经500℃焙烧的催化剂样品的有效比表面积和孔体积均明显增大,表面酸量最多,硝酸镍分解成小颗粒的NiO较易被H₂还原,这些特性是该催化剂样品具有高效加氢脱氧活性的原因.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

Preparation and structure of NaSr0.5Al2B2O7 and NaCa0.5Al2B2O7

Two compounds NaSr_0.5Al₂B₂O₇ and NaCa_0.5Al₂B₂O₇, have been found to crystallize into a new structure type by Rietveld refinement from X-ray powder diffraction data. Their structure belongs to hexagonal space group P6₃/m, with lattice parameters of , for NaSr_0.5Al₂B₂O₇ and , for NaCa_0.5Al₂B₂O₇, respectively. The structure is built up by [Al₂B₂O₇]²⁻ double layer and Na⁺/Ca²⁺ or Na⁺/Sr²⁺ ions alternatively stacking along the c-axis. The sites in the inter-double layer are fully occupied jointly by Na and Ca or Sr, but the intra-double layer sites are only half occupied solely by Na. A mechanism of the transition of the structure from CaAl₂B₂O₇ to present structure type by replacing only 1% Ca by Na (2%) as observed by Chang and Keszler (Mater. Res. Bull. 33 (1998) 299) is also proposed.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.