无机-有机复合材料沸石@聚丙烯酰胺的制备及对Pb2+的吸附研究

重金属污染会引起严峻的环境问题。因此,必须对重金属离子进行测定,但由于重金属离子的含量低并受基体效应影响,检测前需要先将其分离富集。本实验利用一锅法制备了沸石@聚丙烯酰胺复合材料,将其作为分离富集材料,结合火焰原子吸收光谱仪,研究对Pb2+的吸附性能。为了得到最佳的吸附性能,对制备条件中的沸石用量进行了优化,并对优化后的复合材料进行了扫描电镜、热重分析和比表面积表征。利用单一变量法,对固相萃取条件中的溶液pH和振荡时间进行了优化。研究了复合材料在吸附Pb2+过程中的动力学模型、等温线模型和热力学参数。结果表明,在沸石用量为333 mg/g,溶液pH为5和振荡时间为80 min时,复合材料的吸附效率最佳;沸石@聚丙烯酰胺复合材料吸附Pb2+的过程符合二级动力学和Freundlich模型,且在298.15K时,热力学参数 ?H=15614.18 J/mol、?S=65.2 J/mol/K、?G=-1878.059 J/mol,是一个吸热且熵增的自发过程;此外,复合材料经过连续三次吸附和解吸实验,对Pb2+的吸附量基本不变,且解吸率保持在89.7%以上,说明沸石@聚丙烯酰胺复合材料具有较好的再生性能。     

废轮胎回转窑中试热解炭的重金属离子吸附特性

对废轮胎回转窑中试热解炭的重金属离子Pb2＋、Cr3＋和Cr6＋吸附特性进行了研究，分析了溶液pH值、接触时间、吸附剂用量以及溶液初始浓度对重金属去除率的影响。结果表明，溶液pH值对热解炭的重金属去除率有显著影响，阳离子Pb2＋、Cr3＋的去除率随pH的增加而增大，在弱酸和中性环境中去除率接近100％；Cr6＋在强酸性溶液中被还原成为Cr3＋，经二次吸附，总Cr去除率可达99％以上；Pb2＋和Cr3＋的去除率随热解炭用量和吸附时间的增大而增加，热解炭用量和吸附时间有一个最佳值。Pb2＋和Cr3＋的吸附为单分子层吸附，可用Langnuir和两段Freundlich等温吸附式描述，Freundlich拟合指数表明，热解炭具有较好的吸附性能。经酸洗后的热解炭对Pb2＋的去除率变低。     

新型吸附剂的合成、表征及其对Ni(II)的吸附研究

利用滴加法合成了球形含Ni2 交联壳聚糖,并通过胺化引入大量活性氨基,再经除镍制成对重金属镍离子具有较好吸附能力的新型吸附剂[P-C-CTS(Ni)].通过Ni2 吸附容量的测定,IR及XPS分析,验证了合成技术路线的正确性.通过研究pH值对吸附量的影响,初步讨论了无柠檬酸根(Cit)配位体存在时,吸附剂对Ni(II)的吸附为螯合作用.通过Cit存在条件下(cNi=cCit=0.852mmol·L-1),吸附剂对Ni(II)离子和Cit的吸附量随pH值的变化,结合相应pH值下金属镍的形态分布,探讨了其对Ni(II)的吸附机理,研究认为不仅仅是简单的螯合作用,其吸附机理和吸附量与溶液中金属离子的存在形式有关,引入静电吸附原理解释了吸附剂对Ni(II)的吸附现象.     

荞麦皮生物吸附去除水中Cr(Ⅵ)的吸附特性和机理

农业废弃物荞麦皮作为生物吸附剂去除水中Cr(Ⅵ),研究了荞麦皮对Cr(Ⅵ)的去除动力学以及溶液pH、吸附剂用量和Cr(Ⅵ)初始浓度对去除效率的影响;通过FT-IR,XPS,SEM-EDX对荞麦皮表面组成和结构进行表征,探索荞麦皮去除Cr(Ⅵ)的机理.结果显示:荞麦皮对Cr(Ⅵ)有很高的去除效率.常温下5.0 g·L-1的荞麦皮在pH=2.0下对100 mg·L-1 Cr(Ⅵ)溶液的去除率可达99.87%.荞麦皮对Cr(Ⅵ)的去除率随溶液pH降低而升高,在pH=2.0时达到最大;随吸附剂用量增加而增大;随Cr(Ⅵ)初始浓度增加而减小.单位质量荞麦皮对Cr(Ⅵ)的去除量随吸附剂用量增加而减小;随Cr(Ⅵ)初始浓度增加而增加,最后趋于稳定.在20℃,pH=2.0,吸附用量为5.0 g·L-1时,荞麦皮对Cr(Ⅵ)的最大去除容量约为36.4 mg·g-1.荞麦皮吸附去除Cr(Ⅵ)的过程符合准二级吸附动力学.FT-IR,XPS和SEM-EDX分析结果表明:荞麦皮是一个多孔材料,表面存在羧基、氨基、羟基等活性基团;荞麦皮对Cr(Ⅵ)的去除是一个吸附-还原耦合的过程,包括Cr(Ⅵ)在荞麦皮表面上的静电吸附,以及此后的固相还原和对还原态的Cr(Ⅲ)再吸附;Cr(Ⅲ)的吸附主要是通过与荞麦皮表面的羧基、氨基的配位,以及与其中的阳离子发生离子交换作用实现的.     

氧化多壁碳纳米管对Pb~(2+)的吸附性能研究

该文研究了氧化多壁碳纳米管(o-MWNTs)对Pb2+的吸附性能,考察了平衡时间、溶液pH值、溶液体积等因素对吸附行为的影响。在静态吸附条件下:Pb2+能大量并快速地被o-MWNTs吸附,45 min内即可达到吸附平衡,而活性炭(ACs)的吸附平衡时间为90 min。溶液pH值在1.0~7.0范围对吸附量有显著影响,在pH5.0~6.0时o-MWNTs对Pb2+的静态吸附容量为17.43 mg.g-1。o-MWNTs对铅离子的吸附量随着溶液体积的增加而增加,并逐渐趋于稳定,最大吸附量可达25 mg.g-1。在动态吸附实验中,30 mg.L-1的铅离子溶液在SPE小柱的穿透体积为235 mL,溶液体积为400 mL时可完全穿透。动态吸附实验表明,o-MWNTs对铅离子具有较大的吸附容量且萃取回收率高达94%。研究表明,氧化碳纳米管装填的固相萃取小柱可用于中药提取物中Pb2+的残留分析。     

在多孔有机聚合物中构筑广谱性重金属离子吸附活性位

以三维刚性结构的三蝶烯为单体, 通过简单的Friedel-Crafts烷基化反应制备得到高比表面积的三蝶烯基多孔有机聚合物(TPOP), 在TPOP中接枝乙二胺和氯乙酸钠, 构建了广谱重金属离子吸附剂(TPOP-CH₂EDTA). 获得的TPOP-CH₂EDTA具有微孔/介孔结构, 其微孔尺寸为1.6 nm, BET比表面积为634 m²/g, 利于重金属离子传递和配位作用的强化. TPOP-CH₂EDTA对重金属离子具有吸附广谱性, 其对Ag(Ⅰ), Cu(Ⅱ), Ni(Ⅱ), Zn(Ⅱ), Co(Ⅱ), Sn(Ⅳ), Pb(Ⅱ), Cd(Ⅱ), Fe(Ⅲ)和Cr(Ⅲ)等10种重金属离子的去除率均高于98%. 以Pb(Ⅱ)为典型的重金属污染物, 通过Langmuir模型计算得到Pb(Ⅱ)的最大吸附容量高达184.5 mg/g; 具有拟二级吸附动力学特征, 吸附速率快, 动力学常数k₂为0.0173 g·mg^?1·min^?1; 经过5次循环使用后, Pb(Ⅱ)的去除效率仍高达95.8%. TPOP-CH₂EDTA对混合溶液中Pb(Ⅱ)和Cu(Ⅱ)的去除率均高于99%, 且对含有大量无机盐[如Ca(Ⅱ), Mg(Ⅱ), K(Ⅰ)和Na(Ⅰ)离子]和有机化合物的复杂真实水体系, Pb(Ⅱ)和Cu(Ⅱ)的去除效率仍高于90%. 因此, 通过调控多孔有机聚合物微观结构(如比表面积、 孔径和吸附位点密度)而构筑的广谱性重金属吸附材料, 为协同去除复杂水系统中混合重金属离子提供了方案.     

麦秆对重金属pb2+和Cr3+吸附性能的研究

本文以麦秆作为生物吸附剂吸附去除溶液中的pb2+和Cr3+,针对pH值、吸附时间和金属离子浓度等影响吸附的主要因素进行了实验研究,并探讨了麦秆的改性处理.结果表明,溶液pH值是影响吸附的重要因素,麦秆对Pb2+和Cr3++的吸附量随溶液初始pH值的升高而升高.Pb2+和Cr3+在麦秆表面的吸附速度很快,60 min即可...     

13X分子筛去除水中重金属离子的研究

以人工合成的13X型分子筛为吸附剂,研究了水中Pb2 、Cd2 和Cu2 在分子筛上的吸附行为,讨论了Pb2 、Cd2 和Cu2 共存条件下的竞争吸附,并考察了水中存在的Na 、Mg2 、Ca2 等离子对分子筛吸附去除重金属的影响.实验结果表明,13X分子筛对Pb2 、Cd2 和Cu2 3种离子的吸附符合Langmuir模型,最大吸附量分别为2.47mmol/L、2.0mmol/L和1.78mmol/L.在竞争吸附条件下,13X分子筛对3种重金属离子的选择性依次为pb2 ＞Cd2 ＞Cu2 .水中存在的Na 、Mg2 、Ca2 等对分子筛吸附重金属效率有一定的影响,其中Ca2 对Cu2 在分子筛上的去除影响最为显著.     

粉煤灰合成Na-X沸石去除废水中镍离子的研究

粉煤灰通过碱熔融 水热法合成了Na-X型沸石,研究了Na-X型沸石的用量、吸附时间、溶液pH值、初始镍离子浓度和温度对废水中镍离子去除效果的影响。结果表明,Na-X型粉煤灰沸石对镍离子的去除性能与化学原料合成的13X相当,明显优于粉煤灰。在20℃,pH值为6,沸石用量10g/L,吸附15min时,对初始浓度为20mg/L~150mg/L的镍离子去除率均可达90%以上。镍离子的吸附过程符合Langmiur吸附等温方程式,其单层吸附量为11.2×10^-3。粉煤灰沸石重复使用5次,对废水中镍离子的去除率仍高达95%,再生性能良好。     

腐殖酸对La~(3+),Nd~(3+)等重金属离子混合体系吸附的研究

对含有La~(3+),Nd~(3+)的重金属混合体系进行吸附选择性试验,筛选出腐殖酸浓度为1.2 g·L~(-1)时吸附La~(3+),Nd~(3+)的最佳条件(pH=5.4,温度313 K,振荡时间8 h,重金属离子初始浓度0.15 mmol·L~(-1)),得出此条件下吸附优先顺序为:La~(3+)>Pb~(2+)>Cu~(2+)>Nd~(3+)>Cd~(2+)>Zn~(2+)>Co~(2+)>Cr~(3+);HA的吸附总量在室温下拟合二级动力学方程的效果最好;Langmuir方程则能更好地描述HA对重金属离子的等温吸附过程,并且随着温度的升高,HA的最大吸附量逐渐增加;HA对La~(3+),Nd~(3+)等重金属离子的吸附优先顺序受到pH值、温度、振荡时间、重金属离子初始浓度和本身性质的综合影响,且重金属的地球化学性质是主导因素.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.