掺稀土元素Dy和Mn,P,Cu的MgSO4的热释发光光谱

实验测定了MgSO4:Dy,Mn和MgSO4:Dy,P以及MgSO4:Dy,P,Cu等的热释光磷光体的三维发光谱.结果表明,掺入Dy的MgSO4磷光体的热释发光谱线的波长与Dy3+离子的能级跃迁相关,Dy3+为热释光主要发光中心.MgSO4中只掺入Mn时,温度在140℃和190℃附近呈现波长为660nm宽范围的连续发光带,这是Mn形成的发光中心的光谱.当MgSO4中同时掺入Dy和Mn时,660nm的Mn发光带和低于300℃的Dy3+离子的发光谱强度均受到抑制,出现了波长为480nm和580nm峰温在380℃的主发光峰.这表明原MgSO4:Dy的360℃发光峰向高温方向移动了约20℃,Dy3+仍为热释光主要的发光中心,Mn则主要起能量转移的作用.MgSO4:Dy,P热释光三维发光谱可看出,P掺入使MgSO4:Dy的260℃发光峰移至283℃,并且强度大大增加,原360℃发光峰的峰温基本不变.当MgSO4:Dy,P中同时掺入Cu时,主要发光峰的峰温仍在283℃,但360℃发光峰的强度被抑制,480nm和580nm的发光峰的相对强度发生了变化.因此,Dy3+仍是热释光主要的发光中心,P和Cu参与形成新的俘获中心.     

掺稀土元素Dy和Mn,P,Cu的MgSO4的热释发光光谱

实验测定了MgSO₄:Dy,Mn和MgSO₄:Dy,P以及MgSO₄:Dy,P ,Cu等的热释光磷光体的三维发光谱.结果表明,掺入Dy的MgSO₄磷光体的热释发 光谱线的波长与Dy³⁺离子的能级跃迁相关,Dy³⁺为热释光主要发光 中心.MgSO₄中只掺入Mn时,温度在140℃和190℃附近呈现波长为660nm宽范围的 连续发光带,这是Mn形成的发光中心的 关键词： 热释发光光谱 稀土元素镝 硫酸镁     

掺杂型BaFBr:Eu2+的热释发光性质的研究

BaFBr:Eu^2 是利用色心存储电子－空穴对并用可见光激励读出存储信息（产生Eu^2 的4f^65d→4f^7的跃迁）的优良的光激励发光材料。通过热释发光技术研究了BaFBr:Eu^2 的热激活行为，对其低温段和高温段的热释发光峰分别进行了归属，通过对BaFBr:Eu^2 以及掺杂Na^ 或Al^3 的BaFBr:Eu^2 的热释发光（TL）谱和光激励发光（PSL）谱的表征，指出在BaFBr:Eu^2 中掺杂Na^ 或Al^3 影响了F（Br^-）色心，使其陷阱深度变涛，并从理论上加以计算，得出的热致激发能量的变化与光致激光能量的变化能很好地吻合。     

(Zn,Cd)S∶Cu,Cl发光材料的热释发光

在ZnS中分别掺杂质量分数为5%、7%、10%、15%、20%的CdS,得到一系列(Zn,Cd)S∶Cu,Cl粉末电致发光材料样品。测量样品材料的热释发光曲线,发现五个样品在温度-180～-20℃范围内均有两个明显的热释发光峰。CdS含量的变化对材料中陷阱的种类和陷阱深度没有明显的影响,两个峰值温度在-150℃和-50℃附近。Cd离子的掺入改变了材料较深陷阱中载流子的浓度,随着CdS量的增加,使得在-50℃的热释发光峰的相对强度增大。通过测量样品的发光光谱和发光亮度,发现随着CdS含量的增加,样品材料的发射光谱向长波方向移动,发光亮度呈下降的趋势。     

SrWO4∶Eu,Tb发光材料的结构表征与发光性能

采用液相沉淀法合成了SrWO4:Eu,Tb发光材料,XRD衍射测试结果表明,合成材料均具有四方晶系结构.荧光光谱检测表明,在254nm紫外光激发下,SrWO4;0.05Eu的发射光谱出现Eu3+的5D0→7F1(598nm)、5D0→7F2(618nm)跃迁发光峰,SrWO4:0.05Eu,0.05Tb的发射光谱只出现Eu3+的发光峰,说明存在Tb3+,Eu3+离子间的能量传递现象,Tb3+离子的共掺杂能够显著提高Eu3+离子的发光性能.     

(Zn,Cd)S：Cu,Cl发光材料的热释发光

在ZnS中分别掺杂质量分数为5%、7%、10%、15%、20%的CdS,得到一系列(Zn,Cd)S:Cu,Cl粉末电致发光材料样品。测量样品材料的热释发光曲线,发现五个样品在温度-180～-20℃范围内均有两个明显的热释发光峰。CdS含量的变化对材料中陷阱的种类和陷阱深度没有明显的影响,两个峰值温度在-150℃和-50℃附近。Cd离子的掺入改变了材料较深陷阱中载流子的浓度,随着CdS量的增加,使得在-50℃的热释发光峰的相对强度增大。通过测量样品的发光光谱和发光亮度,发现随着CdS含量的增加,样品材料的发射光谱向长波方向移动,发光亮度呈下降的趋势。     

掺Eu3+硅基材料的发光性质

通过溶胶－凝胶技术制备了掺Eu^3 的硅基材料并测试了其三维荧光光谱、激光谱和发射光谱，结果显示，最佳激发波波长为350nm,最强荧光波长为620nm；在350nm光激发下的发射光谱显示Eu^3 的特征发射光谱，产生4条谱带，分别是577nm(^5D0-^7F0)，588nm(^5D0-^7F1),596nm(^5D0-^7F1)和610nm(^5D0-^7F2)。     

Eu(MFA)3bpy配合物的表征和荧光光谱

本文报道了Eu(MFA)3bpy(MFA:对甲氧基苯甲酰呋喃甲酰甲烷,bpy:2.2''-联吡啶)配合物的合成并以元素分析、红外光谱、拉曼光谱和质子核磁共振谱进行了表征.在77K测定了配合物的激发光谱和荧光光谱.光谱数据说明配合物中含有两种类似的Eu3+格位,具有C2v,对称性.     

Feasibility study of CaSO4:Eu,CaSO4:Eu,Ag and CaSO4:Eu,Ag(NP) as thermoluminescent dosimeters

This work evaluates the dosimetric properties of crystals of CaSO₄ doped with unusual elements, such as europium (Eu) and silver (Ag), including their nanoparticle forms, after the incorporation of glass or Teflon and compares them with well-known thermoluminescent dosimeters (TLD). X-ray diffraction analyses showed that samples of doped CaSO₄ exhibit only a single phase corresponding to the crystal structure of anhydrite. Optical spectroscopy confirmed the presence of Eu³⁺ in the crystal matrix and a luminescent gain due the presence of silver nanoparticles. The composites showed thermoluminescent emission glow curves, with a single peak centered at approximately 200 °C for pellets with Teflon and at 230 °C for pellets with glass. The dosimeters based on calcium sulfate doped with europium and silver nanoparticles provided the most intense thermoluminescent (TL) emission of the composites studied. In comparison with commercial TLD, such as LiF:Mg,Ti and CaSO₄:Dy, the CaSO₄:Eu,Ag(NP)+glass produced in this work presented similar low detection limits and higher sensitivity. The new methods for the preparation of dosimeters and the incorporation of glass are shown to be viable because all of the samples presented a linear, reproducible and first order kinetic TL emission.     

CaSO4∶Eu磷光体的热释光特性研究

用热释光三维发光谱仪和蓝色滤光片的热释光仪测定了CaSO4:Eu2+的辐照后的发光曲线,得到峰温为107和144℃波长390nm的发光峰.辐照50d后,107℃发光峰已衰退,发光曲线呈现144℃单个发光峰.经一级力学方程式拟合得到的激活能E=(1.02±0.03)eV与初始升温法(1.07±0.01)eV和峰形法(1.02±0.01)eV的非常符合.用通用级动力学模型拟合发光曲线,得到陷阱能级E=(1.04±0.01)eV,频率因子s=(2.07±0.8)×1012s-1和动力学级数b=1.05±0.02 关键词： CaSO4∶Eu 剂量响应 动力学参量 热释光     

荧光体CaSO4：Eu的近紫外发光性质

CaSO₄:Eu是一种人们早已较为熟知的发光材料,由于其优异的热释发光特性而被广泛应用于辐射剂量学方面。近年来由于崭新的光致发光液晶显示模式的出现,人们又对其近紫外发射特性产生了极大兴趣。考察了CaSO₄:Eu的发光特性和材料的各种制备方法,以及制备条件对发光性能的影响,特别是对其近紫外发射性能的影响。实验表明,对于还原彻底、结晶良好的样品,激活剂Eu几乎全部以二价铕离子的形式存在,是一种很好的近紫外发射材料。该材料能被低压汞蒸气放电辐射有效激发,其发射带的峰值在386nm附近,随Eu的掺杂浓度不同而略有差异,半峰全宽约为16nm,基本满足了近紫外发射的要求,可应用于光致发光液晶显示器件的背照明光源中。     

SrSO4:Eu磷光体的光释光特性

研究了通过掺杂得到的SrSO4:Eu(01mol%)的粉末样品的光释光(OSL)特性.用90Sr的β射线辐照0116—116kGy后，测定了恒定光源激发的光释光发光曲线(CW-OSL)和线性光源激发的光释光发光曲线(LW-OSL)，对发光曲线分析均得到了四种陷阱成分.采用复合作用响应函数得到SrSO4:Eu辐射剂量响应为线性-亚线性.测量了温度对OSL信号的影响，结果表明OSL信号的温度稳定性很好，最灵敏读出温度约为180℃，说明这时OSL信号来自热激发和光激发的共同作用.用60Coγ辐照100Gy后，测量了热释光(TL)三维光谱，确定了发光波长主要位于375nm，可以确定这是来自于Eu2+能级跃迁的发光. 关键词： 光释光 热释光 SrSO4:Eu     

Thermoluminescence and optically stimulated luminescence characteristics of Al2O3 doped with Tb

In the present work policrystals of α − Al₂O₃ doped with terbium were synthesized using the solvent evaporation method. The samples were prepared using Al(NO₃)₃·9H₂O and Tb(NO₃)₃·5H₂O reagents, with Tb concentrations between 1 and 5 mol% and thermally treated at high temperature above ∼1400 °C. X-ray diffraction measurements showed the α-phase formation of samples. TL glow curve presented an intense peak at ∼190 °C and two other with low intensity at 290 and 350 °C after gamma irradiation. The best doping concentration which presented high luminescence was the sample doped with 3 mol% of Tb. TL spectra and fluorescence measurements showed similar luminescence spectra with lines attribute to Tb³⁺ ions. A linear behavior to gamma dose between 1 and 20 Gy was observed in TL, using 190 °C peak as well as in OSL signal, this last carried out using 532 nm wavelength stimulation.     

Al3+掺杂BaFBr:Eu2+中F(Br-)心的性质

作为光激励发光的首选材料BaFBr:Eu^2 ，在其中掺杂一定量的Al^3 后，其光激励发光谱向长波方向发生了较大的红移现象，红移的机理是掺杂的Al^3 离子取代了BaFBr:Eu^2）晶格中的Ba^2 离子，且处于F（Br^-）心的次近邻位所致。本文利用喇曼光谱和电子顺磁共振谱对受掺杂Al^3 微扰的F（Br^-)心的结构进行了研究，首次在喇曼光谱的高频移区观测到了由于掺参Al^3 所引起的新结构的产生，通过电子顺磁共振谱表征了在BaFBr:Eu^2＋中Al^3 与F（Br^-）心的相对位置，并且得出F（Br^-)心与OF^-心存在着空间相关性。     

Thermoluminescent analysis of CaSO4:Tb,Eu crystal powder for dosimetric purposes

The motivation of this work was to produce crystals of CaSO₄ doped with an unusual combination of RE elements such as terbium (Tb) and europium (Eu) in different concentrations, and analyze its thermoluminescent (TL) properties. The crystals were produced by the slow evaporation route using calcium carbonate (CaCO₃) as precursor, and incorporating the dopants (Tb₂O₃ and Eu₂O₃) in a solution of sulfuric acid, that is evaporated and collected again, leaving just CaSO₄:Tb,Eu crystal powder. The terbium and europium ions were incorporated in concentration ratios of 1:1, 2:1 and 5:1 (weight proportions). X-ray diffraction analyses showed that samples of doped CaSO₄ exhibit only a single phase corresponding to the crystal structure of anhydrite. The radioluminescence confirmed the presence of Tb³⁺ and Eu²⁺ in the crystal matrix. The CaSO₄:Tb,Eu crystal powders showed TL emission glow curves with three peaks centered around 170 °C, 270 °C and 340 °C, after irradiation with a ⁹⁰Sr/⁹⁰Y source. Thermoluminescent (TL) characteristics such as linearity, reproducibility and fading were evaluated. Samples produced with concentration ratio of 2:1 of Tb and Eu showed the highest TL intensity. The produced CaSO₄:Tb,Eu samples present TL properties useful for dosimetric purposes.     

柠檬酸-凝胶法合成ZnGa2O4:Mn2+/Eu3+及其发光性能的研究

采用柠檬酸－凝胶法合成了纯的ZnGa2O4粉末以及ZnGa2O4:Mn^2 /Eu^3 粉末,利用X射线衍射（XRD）、热重及差热分析（TG－DTA）、发光光谱等测试手段对ZnGa2O4和ZnGa2O4:Mn^2 /Eu^3 的结晶过程、发光性质进行了研究。XRD结果表明,柠檬酸－凝胶法合成的样品在500℃。发光光谱测试表明ZnGa2O4:Mn^2 在450nm和506nm处出现两个发射带,前者属于ZnGa2O4基质的发射,后者属于Mn^2 的^4T1→^6A1的跃迁发射。ZnGa2O4:Eu^3 则呈现Eu^3 的特征红光发射,最强峰位于613nm,属于Eu^3 的^5D0→^7F2超灵敏跃迁。通过光谱分析进一步证实了ZnGa2O4:Mn^2 /Eu^3 的发光机理是基质敏化,吸收能量并向激活离子传递能量。     

SrAl2O4：Eu2+的长余辉发光特性的研究

本文研究了SrAl2O4:Eu2+材料的发光及长余辉特性.首次得到了这一材料的发光衰减由初始的快衰减和后期的慢衰减过程所组成,以及热释发光光谱出现两个热释发光峰值的实验结果.对所得结果进行了分析讨论,提出了这一材料的发光衰减是由两个足够深的电子陷阱所引起.     

Luminescence spectroscopy of Eu3+ and Mn2+ ions in MgGa2O4 spinel

Photoluminescence and excitation spectra of the spinel-type MgGa₂O₄ with 0.5 mol. % Mn²⁺ ions and Eu³⁺ content from 0 to 8 mol. % have been investigated in this work at room temperature. Polycrystalline samples were synthesized via high-temperature solid-state reaction method. Photoluminescence spectra of all samples exhibit host emission presented by a broad “blue” band peaking ∼430 nm, which consists of at least three elementary bands that correspond to different host defects. Excitation of the host luminescence showed the broad band with a maximum at 360 nm. Characteristic bands of d–d transitions of Mn²⁺ ions and f–f transitions of Eu³⁺ ions together with charge-transfer bands (CTB) of these ions were also found on the excitation spectra. Mn²⁺ and Eu³⁺ co-doped samples emit in green and red spectral regions. Mn²⁺ ions are responsible for the green emission band at 505 nm (⁴Т₁→⁶А₁ transition). The studies of photoluminescence spectra of activated samples with different Eu³⁺ ions content show characteristic f–f luminesecence of Eu³⁺ ions. The maximum of Eu³⁺ emission was found at 618 nm (⁵D₀→⁷F₂) and optimal concentration of activator ions was around 4 mol. %.