用恒温热重法测定1-己基-3-甲基咪唑苏氨酸离子液体[C6mim][Thr]蒸汽压和蒸发焓

用中和法合成了氨基酸离子液体(AAIL)1-己基-3-甲基苏氨酸盐[C₆mim][Thr],并用核磁共振氢谱(¹H NMR)和核磁共振碳谱(¹³C NMR)进行了表征。以苯甲酸为参考物质,用恒温热重法确定了AAIL[C₆mim][Thr]的蒸汽压和在平均温度下(T_av= 438.15 K)的蒸发焓(Δ^g_lH_m^? (T_av) =128.5 ± 6.0 kJ·mol^-1)。利用Verevkin等人提出的方法计算得到AAIL[C₆mim][Thr]气态和液态的恒压热容差(Δ^g_lC_pm^? = -70.8 J·K^-1·mol^-1),进而计算了不同温度的蒸发焓,其中参考温度(298.15 K)下的蒸发焓Δ^g_lH_m^? (298.15 K) = 138.4 kJ·mol^-1,只比应用我们提出的蒸发焓理论模型估算值大1.6 kJ·mol^-1,小于恒温热重法的实验误差3.0 kJ·mol^-1,说明这个蒸发焓的理论模型有一定的合理性。借助Clausius-Clapeyron方程估算了AAIL[C₆mim][Thr]的假想的正常沸点T_b= 522.07 K,以及沸点的蒸发熵Δ^g_lS_m^? (T_b) = 228.5 J·K^-1·mol^-1,进一步得到了不同温度的蒸发熵和蒸发自由能Δ^g_lG_m^? (T),其结果表明蒸发自由能随着温度的上升而减小,达到沸点温度T_b时变为零,而蒸发熵则随着温度上升而增大,是AAIL[C₆mim][Thr]蒸发过程的驱动力。     

1-甲基-3-乙基咪唑缬氨酸盐离子液体[C2mim][Val]的热化学

用中和法合成了氨基酸离子液体1-甲基-3-乙基咪唑缬氨酸盐([CB_2Bmim][Val]). 在298.15±0.01 K下, 利用恒温溶解反应热量计测定了不同含水量的[CB_2Bmim][Val]溶解成不同质量摩尔浓度溶液的溶解焓, ΔB_solBHB_mB (w), 借助标准加入法(SAM)和Archer方法得到了无水离子液体[CB_2Bmim][Val]的标准摩尔溶解焓, . 利用RB-II型精密转动弹热量计测定了该离子液体的燃烧热, 计算了其标准摩尔燃烧焓 和标准摩尔生成焓 |并结合该离子液体的标准摩尔溶解焓和乙基咪唑阳离子[CB_2Bmim]^＋在水溶液中的标准摩尔生成焓, 计算了[Val]P^－离子在水溶液中的标准摩尔生成焓. 利用RD496-III型热导式微量热量计测定了不同质量摩尔浓度[CB_2Bmim][Val]水溶液的稀释焓, 根据扩展的Debye-Hückel方程计算得到的相对表观摩尔焓P^φPL和根据Pitzer离子相互作用模型的计算值在实验误差范围内很好一致.     

“一锅法”合成离子液体1-乙基-3-甲基咪唑醋酸盐

以1-甲基咪唑,溴乙烷和乙酸铅为原料,采用"一锅法"合成了离子液体1-乙基-3-甲基咪唑醋酸盐,产率87%,其结构经UV,IR和元素分析确证。优化反应条件为:1-甲基咪唑100 mmol,n(溴乙烷):n(1-甲基咪唑):n(乙酸铅)=3.6:2.0:1.0,于60℃反应20 h。     

1-丁基-3-甲基咪唑四氟硼酸盐的热稳定性、平衡蒸汽压和标准蒸发焓

利用非等温、等温热重分析(TG)法,研究了高纯氮气气氛下1-丁基-3-甲基咪唑四氟硼酸盐([bmim][BF4])离子液体的热稳定性、平衡蒸汽压和标准蒸发焓.非等温热重(TG)曲线表明[bmim][BF4]的初始分解温度(Tonset)和最大分解速率对应的温度(Tm)分别为697和734K.然而长期等温TGA研究表明,[bmim][BF4]的最高可使用温度约为513K.另外,利用基于TG的蒸发技术研究了[bmim][BF4]的平衡蒸汽压(pe)与温度的关系并计算了标准蒸发焓.在503-543K温度范围内,离子液体[bmim][BF4]的pe和温度的关系是:lgpe=(16±1)+(-6.85±0.25)×103/T.[bmim][BF4]的标准蒸发焓为(131±5)kJ·mol-1.     

1-烷基-3-甲基咪唑氯化物焓变的热重分析

The structures of ionic liquids (ILs) based on 1-alkyl-3-methylimidazolium chloride [C_nmim]Cl (n = 2, 4, 6), (1-ethyl-3-methylimidazolium chloride [C₂mim]Cl, 1-butyl-3-methylimidazolium chloride [C₄mim]Cl, and 1-hexyl-3-methylimidazolium chloride [C₆mim]Cl) were elucidated by ¹H NMR and ¹³C NMR experiments. The vaporization characteristics of these ILs were studied by thermogravimetric analysis. Dynamic and isothermal thermogravimetric experiments were conducted in this study. The purpose of the dynamic experiments was to determine the initial decomposition temperature of the experimental sample and the temperature range for the isothermal thermogravimetric experiments. The purpose of the isothermal experiments was to record the mass dependence of the sample on time in the experimental temperature range. The Langmuir equation and Clausius-Clapeyron equation were used to fit the experimental data and obtain the vaporization enthalpies of these ILs at the average temperature within the experimental temperature range. However, in order to expand the applicability of the estimated values and to compare them with the literature data, the vaporization enthalpy ΔH_vap(T_av) measured at the average temperature was converted into vaporization enthalpy ΔH_vap(298) at ambient temperature. The difference between the heat capacities of the ILs in the gaseous and liquid states at constant pressure, Δ_l^gC_pm^ө proposed by Verevkin, was used in this conversion process. The experimental data for substance density and surface tension at other temperatures were obtained by referring to the literature. In addition, the data for density and surface tension at T = 298.15 K were obtained by applying the extrapolation method to the literature values for other temperatures. The vaporization enthalpy of the 1-octyl-3-methylimidazolium chloride IL [C₈mim]Cl was estimated by using the new vaporization model we had proposed in our previous work and compared with the reference value. The estimated value for [C₈mim]Cl was on the same order of magnitude as the reference value. We compared the vaporization enthalpies in the present study with those for the carboxylic acid imidazolium and amino acid imidazolium ILs ([C_nmim]Pro (n = 2-6) and [C_nmim]Thr (n = 2-6), respectively in our previous work. The results revealed that a change in the anion type affects the vaporization enthalpy of the ILs in the order amino acid imidazolium > carboxylic acid imidazolium > halogen imidazolium, when the cation is the same. Considering the structural differences between the three kinds of ILs, the abovementioned order may be related to the intermolecular hydrogen bonds. There were no intermolecular hydrogen bonds in the [C_nmim]Cl (n = 2, 4, 6) ILs studied here. Therefore, the vaporization enthalpy of [C_nmim]Cl (n = 2, 4, 6) was the lowest among the three kinds of ILs considered.     

1-烷基-4-氨基-1,2,4-三唑硝酸盐含能离子液体的蒸气压及其摩尔汽化焓的理论研究

合成了1-烷基-4-氨基-1,2,4-三唑硝酸盐含能离子液体([RATZ]NO₃),并通过核磁和红外进行了结构表征;采用Gaussian09/B3LYP/6-311+G(d,p)密度泛函理论,计算了[RATZ]NO₃的离子间相互作用能及摩尔体积;在298 K-323 K温度范围内,测定了不同配比[RATZ]NO₃-EtOH混合溶液的饱和蒸气压,其中乙醇摩尔分数分别为0.984、0.996、0.999以及1.000。系统研究了[RATZ]NO₃-EtOH混合溶液的饱和蒸气压、[RATZ]NO₃的蒸气压及摩尔汽化焓与温度、离子间相互作用能以及结构之间的关系。结果表明：[RATZ]NO₃-EtOH混合溶液的饱和蒸气压随着温度的升高、离子间作用能的减小以及阳离子体积的增大而增大,其沸点比纯溶剂高,且在298 K-323 K温度范围内[RATZ]NO₃的平衡蒸气压均低于250 mPa,因此说明含能离子液体具有不挥发性,蒸气压极低,并通过理论计算得到的离子间相互作用能及体积,解释了[RATZ]NO₃的摩尔汽化焓随烷基链增长而降低的原因。     

离子液体(1-甲基-3-羧甲基咪唑)钴配合物的合成和晶体结构

由离子液体1-甲基-3-羧甲基咪唑硫酸氢盐([C6H9N2O2][HSO4])和氯化钴合成了一种新的配合物[Co(H2O)4(C6H8N2O2)2]Cl2.2H2O;采用单晶X射线衍射方法测定了配合物的晶体结构.结果表明,所合成的配合物C12H28Cl2CoN4O10属于三斜晶系,空间群P-1,a=0.66753(5)nm,b=0.91751(6)nm,c=1.80604(13)nm,α=85.618(5)°,β=83.385(5)°,γ=83.443(5)°,V=1.08934(13)nm3,Z=2,Mr=520.23,F(000)=538,Dc=1.580g.cm-3,μ(Mo-Kα)=1.088mm-1,R1=0.0861,wR2=0.2878.单晶X射线分析结果表明,在所合成的配合物中,每个1-甲基-3-羧甲基咪唑除羧基外其它原子均位于同一平面,咪唑环带正电荷,而羧基氢原子消失;即整个1-甲基-3-羧甲基咪唑分子不带电荷.总体而言,配合物的内界[Co(H2O)4(C6H8N2O2)2]2+带两个正电荷,外界游离的两个氯离子起平衡电荷作用.     

二氰胺1-羟乙基-3-甲基咪唑离子液体的合成及对糖类化合物的溶解性能

根据离子液体结构-性能的关系,设计合成了一种新的低熔点、低黏度的功能化离子液体二氰胺1-羟乙基-3-甲基咪唑[Hemim][N(CN)2],并在298.2～353.2K的温度范围内测定了α-D-木糖、α-D-葡萄糖、D-果糖、蔗糖、D-乳糖、麦芽糖、棉子糖和木聚糖在该离子液体中的溶解度,计算了糖类化合物在离子液体中的标准溶解热力学参数.实验结果表明,除木聚糖外其他糖类化合物在[Hemim][N(CN)2]中均具有较高的溶解度,且其溶解度随着温度的升高显著增大.木聚糖属于多聚糖,溶解度较小,但温度效应非常明显.糖类化合物的溶解热力学参数SΔGo、TΔSSo和ΔHSo均为正值,且ΔHSoTΔSSo,说明溶解为焓控制过程.红外光谱结果表明,在溶解过程中木聚糖的氢键受到了一定程度的破坏,但它的结构并未发生明显的变化.     

五种1-烷基-2,3-二甲基咪唑型离子液体的合成及作为Li/LiFeO4电池电解液的研究

合成了五种新的1-烷基-2,3-二甲基咪唑二(三氟甲基磺酰)亚胺离子液体(alkyl-DMimTFSI).以离子液体作为Li/LiFeO4电池电解液,分别考察不同烷基(正丁基、正戊基、正辛基、异辛基和正癸基)对电解液理化性质、界面性质和电池行为的影响.结果表明离子液体的电化学窗口都可以达到5.6V(-0.4～5.2Vvs.Li+/Li),显示它们具有较好的电化学稳定性.加入碳酸亚乙烯酯作为添加剂后,离子液体电解液在Li负极形成稳定的固体电解质相界面膜(SEI),从而提高了Li负极的稳定性,保护了Li片不受腐蚀.电化学阻抗和循环伏安分析进一步揭示LiFeO4正极与离子液体电解液也有良好的兼容性.此外,研究还表明离子液体中烷基种类严重影响它们的电池行为.采用butyl-DMimTFSI和amyl-DMimTFSI电解液体系的电池充放电容量和可逆性明显优于另外三种离子液体,它们的首次放电容量分别达到145和152.6mAh/g,并表现出良好的充放电循环性能.因粘度最大,采用isooctyl-DMimTFSI电解液的电池首次放电容量仅为8.3mAh/g,但添加碳酸丙烯酯(质量比1∶1)稀释后首次放电容量上升至132.4mAh/g.     

氯化1-乙基-3-甲基咪唑离子液体表面印迹聚合物的合成及其特异吸附和固相萃取性能研究

以氯化1-乙基-3-甲基咪唑(C₂mimCl)离子液体为模板分子, 甲基丙烯酸和乙二醇二甲基丙烯酸酯为双功能单体, 聚苯乙烯-二乙烯苯为载体, 制备了C₂mimCl表面印迹聚合物(C₂mimClMIP/PS-DVB). 采用红外、扫描电镜和Brunauer-Emmett-Teller分析技术对C₂mimClMIP/PS-DVB进行了表征. 通过静态吸附实验研究了C₂mimClMIP/PS-DVB对模板分子及其结构类似物的吸附行为和选择性识别特性. 结果表明, 聚合物对C₂mimCl和氯化1-丁基-3-甲基咪唑(C₄mimCl)两种离子液体有高度的选择性识别作用. 将C₂mimClMIP/PS-DVB作为固相萃取(SPE)剂制备成SPE柱, 并与高效液相色谱联用, 考察了C₂mimClMIP/PS-DVB的动态吸附性能. 结果表明, 在选定的参数条件下, SPE柱能够从结构类似物中选择性分离富集C₂mimCl和C₄mimCl, 且具备很好的稳定性和可再生性能. 将SPE柱用于地下水中C₂mimCl的分离富集, 显示出良好的实用性能.     

Study on the enthalpy of solution and enthalpy of dilution for the ionic liquid [C3mim][Val] (1-propyl-3-methylimidazolium valine)

A new amino acid ionic liquid (AAIL) [C₃mim][Val] (1-propyl-3-methylimidazolium valine) was prepared by the neutralization method. Using the solution-reaction isoperibol calorimeter, molar solution enthalpies of the ionic liquid [C₃mim][Val] with known amounts of water and with different concentrations in molality were measured at T = 298.15 K. In terms of standard addition method (SAM) and Archer’s method, the standard molar enthalpy of solution for [C₃mim][Val] without water, ${\mathrm{\Delta }}_{\text{s}}{H}_{\text{m}}^{\circ }$ = (−55.7 ± 0.4) kJ · mol⁻¹, was obtained. The hydration enthalpy of the cation [C₃mim]⁺, ΔH₊ ([C₃mim]⁺) = −226 kJ · mol⁻¹, was estimated in terms of Glasser’s theory. Using the RD496-III heat conduction microcalorimeter, the molar enthalpies of dilution, Δ_DH_m(m_i → m_f), of aqueous [C₃mim][Val] with various values of molality were measured. The values of Δ_DH_m(m_i → m_f) were fitted to Pitzer’s ion-interaction model and the values of apparent relative molar enthalpy, ^φL, calculated using Pitzer’s ion-interaction model.     

Volatility of molten salts [Ph4P][NTf2] and Cs[NTf2]

The two ionic compounds [Ph₄P][NTf₂] and Cs[NTf₂] were qualified to be suitable liquid materials for different high temperature applications. Development and optimization of these application techniques require knowledge of the thermodynamic properties of vaporization. Vapor pressures and vaporization enthalpies have been measured by using quartz-crystal microbalance. Solubility parameters and miscibility of ionic liquids in practically relevant solvents were assessed.     

离子液体[C2mim][GaCl4]的溶解热研究

在干燥氩气氛下, 用等摩尔的高纯无水GaCl3和[C2mim][Cl](氯化1-甲基-3-乙基咪唑)直接搅拌混合, 制备了淡黄色透明的的离子液体[C2mim][GaCl4] (1-ethyl-3-methylimidazolium chlorogallate) . 在298.15 K下, 利用具有恒温环境的溶解反应热量计, 测定了这种离子液体的不同浓度摩尔溶解焓 . 针对[C2mim][GaCl4]溶解于水后即分解的特点, 在Pitzer电解质溶液理论基础上, 提出了确定这种离子液体标准摩尔溶解焓的新方法, 得到了[C2mim][GaCl4]在水中的标准摩尔溶解焓, ＝－132 kJ•mol－1, 以及Pitzer焓参数组合: ＝－0.1373076和 ＝0.3484209. 借助热力学循环和Glasser离子液体晶格能理论, 用Ga3＋, Cl－和[C2mim]—的离子水化焓数据以及本文得到的[C2mim][GaCl4]标准摩尔溶解焓, 估算了配离子4Cl－(g)解离成Ga3＋(g)和4Cl－(g)的解离焓ΔHdis([GaCl4]-)≈5855 kJ•mol－1. 这个结果揭示了离子液体[C2mim][GaCl4]的标准摩尔溶解焓绝对值并不很大的原因, 即是很大的离子水化焓被很大的[GaCl4]－(g)的解离焓相互抵消了.     

Thermodynamic studies of the ionic liquid 1-hexyl-3-methylimidazolium chloride [C6mim][Cl] in polyethylene glycol aqueous solutions

Vapour pressure osmometery (VPO) measurements at T = 308.15 K for {[C₆mim][Cl] + water}, {[C₆mim][Cl] + (0.005, 0.0155, and 0.0263) mol · kg⁻¹ PEG2000 + water} and {[C₆mim][Cl] + (0.0017, 0.0052, and 0.0088) mol · kg⁻¹ PEG6000 + water} systems and isopiestic measurements at T = 298.15 K for {[C₆mim][Cl] + PEG2000 + water} and {[C₆mim][Cl] + PEG6000 + water} systems have been carried out. The VPO measurements were carried out at very low concentrations of PEG and from which the values of the water activities, osmotic coefficients, vapour pressure and activity coefficients were obtained. The data obtained from the VPO method show that over the whole concentration range of the ionic liquid (IL), the activity coefficients of [C₆mim][Cl] in the presence of PEG2000 are increased. Although, at high IL concentrations, the values of the activity coefficient of [C₆mim][Cl] in the presence of PEG6000 are also increased, however for low concentrations of IL the values of the activity coefficient of [C₆mim][Cl] in pure water are larger than those in aqueous PEG6000 solutions. For a known IL concentration, the values of water activity coefficient for the binary {[C₆mim][Cl] + water} system are larger than those for the ternary {[C₆mim][Cl] + PEG + water} systems and decrease by increasing the concentration of PEG or decreasing the molar mass of PEG. The constant water activity lines of the all ternary systems obtained from the isopiestic method show positive deviation from the linear isopiestic relation (Zdanovskii–Stokes–Robinson rule) derived using the semi-ideal hydration model. The results have been interpreted in terms of the solute–water and solute–solute interactions.     

Density estimated physicochemical properties of alanine-based ionic liquid [C7mim][Ala] and its application in selective transesterification of soybean oil

Amino acid ionic liquid (AAIL) based on alanine, 1-n-heptyl-3-methylimidazolium alanine ([C7mim][Ala]), has been prepared and characterized. Since the IL can form strong hydrogen bonds with water, trace amount of water is a problematic impurity in the IL. Using the standard addition method (SAM), the densities were measured in the temperature range from 293.15 to 343.15±0.05 K. On the basis of the experimental data of density, the surface tension , molar volume, and the molecular volume Vm, molar enthalpy of vaporization lgHm0, and the thermal expansion coefficients , for [C7mim][Ala] were estimated using semi-empirical methods. Also the interstice model has been verified with good accordance. Then the [C7mim][Ala] was taken as catalyst in the transesterification reaction with fatty acid, where soybean oil was used as raw material and methanol as reactant. The amount of catalyst, alcohol consumption, reaction time, temperature and other factors of the reaction were investigated. Using GC determination, the conversions were calculated by the internal standard method. The main ingredients of the products were identified by GC-MS as palm methyl ester and linoleic acid methyl ester only, which showed high selectivity in palmitic acid and linoleic acid.