1.3μm偏振无关半导体光放大器单片集成模斑变换器

用金属有机化学气相外延生长并制作了 1.3μm脊型波导偏振无关半导体光放大器集成模斑变换器 ,器件有源区为同时采用压应变量子阱和张应变量子阱的混合应变量子阱结构以获得TE和TM偏振模式的增益平衡 ,模斑变换器采用一种新型脊型侧向锥形波导结构 ;集成模斑变换器的半导体光放大器远场发散角为 12°× 15° ,接近圆形光斑 ,与平头标准单模光纤耦合损耗为 - 2 .6dB ,在水平和垂直方向上的 - 1dB耦合对准容差分别为± 2 .3μm和± 1.6 μm ;在 2 0 0mA偏置电流下 ,半导体光放大器小信号增益近 2 4dB ,在 12 80～ 1340nm波长范围内偏振灵敏度小于 0 .6dB。     

仅有相邻波导耦合的定向耦合器的一般解法

应用切比雪夫多项式 ,求得了仅有相邻波导耦合的 (N +1)× (N +1)定向耦合器在弱耦合、无损耗和忽略正交偏振模场分量间耦合的情形下波导耦合方程的通解。列出线形排列 2× 2 ,3× 3,4× 4定向耦合器的解的表达式 ,并对环形排列 3× 3定向耦合器的解作了较详细的分析     

用于波导阵列——光纤阵列自动对接的多目标演化算法的研究

开发设计了一种新的列阵自动对接方法,该方法将多目标演化法导入光纤—光波导列阵—光纤列阵的自动对接,并行操作次数较常规遗传法大幅减少.数值仿真表明,对于模场非对称因子为0.4%的单模波导列阵与光纤列阵的双芯对接,能实现0.04 dB的平均端面耦合损耗.用于1×8波导分支耦合器与通道间距误差在0.35 μm以内的光纤列阵对接,自动耦合仿真达到了小于0.1 dB的平均端面耦合损耗,最大值与最小值的差小于0.06 dB.     

浅海波导界面对点源振速方向的影响

采用“虚源法”分析计算了浅海波导环境中接收点处点源总振速方向与水平面夹角,侧重讨论确定性界面反射对总振速方向的影响。研究结果表明：总振速方向和接收点与声源的水平距离、两者深度,海底、海面特性以及声速剖面等有关。在等声速均匀浅海波导中,由于确定性界面反射的影响,当直达声掠射角为1°～50°时,合成总振速方向偏离直达声方向达1.5°～10.5°,声速剖面呈负梯度时,偏离程度更甚.     

Kr-CS2体系势能面及束缚态能级的理论研究

本文采用单双迭代(包括非迭代三重激发)耦合簇CCSD(T)方法,对C、S原子采用aug-cc-PVTZ基组,对Kr原子采用cc-PVTZ –DK基组,并且加上中心键函数(3s3p2d2f1g),计算得到Kr-CS2体系的势能面。该势能面为T型结构,存在一个全局极小值和两个等价的局域极小值。全局极小值位于R =7.05 a0,θ= 90°处,势能值为-396.194 cm-1。两个局域极小值分别位于R = 10.15 a0,θ= 0°和180°处,势能为-243.647 cm-1。利用该势能面,通过数值求解相应的薛定谔方程,计算得出体系J≤10的束缚态能级及微波谱跃迁频率,并通过跃迁频率拟合得到相应的光谱常数。     

一种基于斜光栅辅助的非对称耦合器型光分插复用器

提出了一种基于斜光栅辅助的非对称耦合器型光分插复用器。运用复合波导的三维正交模式,对器件的三种可能的结构进行了理论分析,选出粗波导光栅型结构。利用耦合模理论,模拟了斜光栅的耦合特性并对其倾斜角进行优化设计。通过回波峰值设计法,将器件的工作波长放在波分复用信道之内,回波峰值波长放在波分复用信道之外,使得器件的性能大有提高。模拟结果表明器件的串扰可达到-30 dB,回波损耗可达到-25 dB。同时,器件的关键工艺容差较大,易于批量化生产。当斜光栅的倾斜角度在2.5°到4.5°之间时,器件的串扰低于-28 dB,回波损耗低于-22 dB。     

光通信中的玻璃无源器件的制备与研究

本文报道了以高质量的BK7光学玻璃为衬底,通过稀释Ag+-Na+离子交换技术,制备出低损耗的表面条波导,并用近场法测量出条波导的模场分布曲线。给出光纤与波导耦合的失配损耗为0.54dB,条波导传输损耗为0.21dB/cm.以及在此工作基础上,成功地研制了适用于大容量相于光通信系统的1×2和1×4单模波导分束器。     

一种新型慢波结构TM01-TE11模式转换器的数值模拟

 设计了一种新型L波段慢波结构式圆波导TM₀₁-TE₁₁模式转换器，该转换器的尺寸为φ15.0 cm×40.8 cm，通过金属分割片将圆波导分成两个180°区域并在其中一个区域内设置半环形慢波结构。当TM01入射时，在两个区域内激励起扇形波导TE11模式，由于慢波结构的存在，该模式在两个区域内的传播常数不一样。适当调节慢波结构的参数，可使两个区域内传输的扇形TE11模式在金属分割片尾部相位相差180°，这两个扇形TE11模式耦合成为圆波导TE11模式输出，实现模式转换。建立数值模型并进行了模拟，结果表明在工作频率1.8 GHz处转换效率96%，反射率低于0.04，功率容量超过1.7 GW。     

与纳米腔相耦合的一维波导中的单光子散射

我们研究了与包含三能级原子的纳米腔相耦合的一维耦合谐振器波导中的单光子散射,分别讨论了纳米腔与耦合谐振器波导局域和非局域的两种耦合方式.在局域耦合的情况下,不同偏振光子的透射及反射波谱关于共振点对称.而在非局域情况下,透射和反射系数中的对称性消失,峰和谷的位置向失谐较大处移动.耗散对单光子散射也会产生影响.     

二维介质柱光子晶体波导的优化设计

通过改变靠近导光区域介质柱的直径和周期,优化设计了二维介质柱光子晶体波导.结果表明：单独增大和减小柱的直径以及增大柱的周期不能提高波导的传输特性;单独减小柱的周期能提高波导的传输特性,获得传输系数小于1 dB,带宽80 nm的波谱;同时减小柱的直径及周期能够极大的提高波导的传输特性,得到了带宽为150~250 nm,传输系数小于1 dB的波谱.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.