吡啶类碳离子液体电极对酚磺乙胺的电化学行为及其分析应用

用离子液体1-丁基吡啶六氟磷酸盐(BuPyPF6)作为粘合剂构置了碳离子液体修饰电极(BuPyPF6-CILE).在0.05 mol/L H2SO4溶液中,用循环伏安法研究了在BuPyPF6-CILE和传统碳糊电极(TCPE)上酚磺乙胺(ESL)的电化学行为,建立了测定尿样和血清样品中ESL含量的新方法.ESL在BuPyPF6-CILE上的氧化峰电流响应是其在TCPE上的8.7倍,峰电位差降低到0.101 V,电子转移速率常数Ks=0.544 s-1,电极表面平均吸附量为1.66×10-9 mol·cm2.ESL的氧化电流与其浓度在8.0×10-8～2.0×10-6mol/L和5.0×10-6～1.0×10-4mol/L范围内呈线性关系,检出限为3×10-8mol/L(S/N=3).连续5次测定2.0×10-6mol/L ESL溶液的RSD为1.5%.     

氯丙嗪在离子液体BMIMPF6修饰玻碳电极上的伏安行为

对氯丙嗪(CPZ)在离子液体BMIMPF6修饰玻碳电极(BMIMPF6/GC)上的伏安行为进行了研究.发现CPZ在该修饰电极上于065V左右产生氧化还原峰,峰的可逆性比玻碳电极(GC)有较大改进,其电极过程为吸附控制.在0050 mol/L磷酸缓冲溶液(pH 4)中,CPZ在BMIMPF6/GC上的氧化峰的峰电流约为GC上的2倍.在优化实验条件的基础上,采用微分脉冲伏安法对不同浓度CPZ溶液进行了测定.结果表明,CPZ在BMIMPF6/GC上的氧化峰电流与浓度在56×10-9～30 ×10-5mol/L范围内有线性关系.将此方法用于尿样的测定,其加入回收率为97％左右.用3种电极测定了CPZ的表观扩散系数,其大小为D(BMIMPF6/GC)＞DOMIMBF6/GC)＞D(GC),这与电极表面积变化及膜内扩散有一定关系.     

对乙酰氨基酚在碳纳米管-离子液体糊修饰电极上的电化学行为及分析应用

制备了碳纳米管-离子液体糊修饰电极并用电化学方法对其进行了表征,研究对乙酰氨基酚在碳纳米管-离子液体糊修饰电极上的电化学行为,建立了以碳纳米管-离子液体糊修饰电极测定对乙酰氨基酚(APAP)的灵敏的电化学方法.在优化的实验条件下,对乙酰氨基酚的氧化峰电流与其浓度在1.0×10-7～1.0×10-6 mol/L和1.0×...     

杀螟硫磷在离子液体修饰预处理玻碳电极上的电化学行为及测定

采用滴涂法制备了离子液体(IL)修饰预处理玻碳电极(IL/PGCE),建立了一种用于高效检测杀螟硫磷(FNT)的方法。利用循环伏安法(CV)对IL/PGCE进行了表征;通过方波伏安法(SWV)研究了杀螟硫磷在修饰电极上的电化学行为,并利用扫速研究了杀螟硫磷在IL/PGCE上的反应过程;讨论了pH值、预处理电位和时间、修饰剂含量、富集电位和时间等影响传感器性能的重要参数。在最优条件下,修饰电极对杀螟硫磷展现出较好的电化学响应,在0.001～1μg·L^-1和1～100μg·L^-1的范围内,峰电流与杀螟硫磷浓度之间呈现良好的线性关系。该方法具有较好的重现性和抗干扰能力,能够用于实际样品中杀螟硫磷的检测,样品回收率为89.6%～125.5%。     

基于多孔碳固载离子液体修饰电极的叔丁基对苯二酚的检测研究

制备了多孔碳固载离子液体纳米材料修饰玻碳电极(GCE),用于抗氧化剂叔丁基对苯二酚(TBHQ)的检测研究。不同电极上的交流阻抗结果表明,经过多孔碳固载离子液体修饰后的玻碳电极阻抗显著减小。多孔碳固载离子液体修饰后电极的氧化峰电流为41.93μA,比修饰前增大约5.5倍,说明多孔碳固载离子液体可显著提高电极的导电性,促进电极表面的电子转移,提高检测灵敏度。用时间~电流曲线测得TBHQ的线性范围为1.00~120.00μg/mL,检出限为0.16μg/mL。     

抗坏血酸在离子液体修饰玻碳电极上的电化学行为

利用离子液体1-丁基-3-甲基咪唑四氟硼酸盐(BMIMBF4)对玻碳电极(GCE)进行修饰,制备了BMI-MBF4/GCE电极.在0.1mol/L的磷酸盐缓冲溶液中,采用循环伏安法研究了抗坏血酸在BMIMBF4/GCE电极和裸玻碳电极(GCE)上的电化学行为.结果表明,pH=5.7的磷酸盐缓冲溶液为最佳测定底液,最佳富集时间为120s;BMIMBF4/GCE对抗坏血酸的氧化反应有很好的电化学催化作用.抗坏血酸的氧化峰电流与其浓度在2.0×10-4～1.0×10-2 mol/L的范围内呈良好的线性关系,相对标准偏差为4.53%(n=5).     

邻苯二酚在活化玻碳电极上的电化学行为

邻苯二酚( QH2,儿茶酚)等有机化合物是人体内的电活性物质,直接参与人体内的各种生理过程.     

苯甲醛在离子液体中的电化学行为

应用线性扫描循环伏安法、方波循环伏安法和计时电量法测定苯甲醛在3种离子液体C4M IMBF4、C6M IMBF4和C8M IMBF4中的电化学行为.实验表明,在C4M IIVIBF4离子液体中苯甲醛于GC电极上的还原包含两个连续、不可逆单电子过程,对应的方波I~E曲线峰电位Ep为-1.39 V和-1.69 V,估算的扩散系数分别为D1=1.5×10-8cm2/s和D2=1.3×10-8cm2/s.而在C6M IMBF4和C8M IMBF4离子液体中,则苯甲醛于GC电极仅显示一个电流峰,这可能是因为C4M IMBF4的碱性较C6M IMBF4和C8M IMBF4弱的缘故;而电流的衰减时间亦依C4M IMBF4,C6M IMBF4,C8M IMBF4,次序增长,并会导致更慢的异相动力学过程.     

细胞色素C在离子液体修饰电极上的电化学行为

分别合成了疏水和亲水性咪唑类离子液体,并制备了相应的两种离子液体修饰的玻碳电极。循环伏安法测量结果显示,细胞色素C在离子液体修饰的玻碳电极上的电子传递过程为一扩散控制的准可逆反应,表明咪唑类离子液体也可用作细胞色素C电子传递的有效促进剂。电化学交流阻抗谱的测量结果得到了与循环伏安相同的结论。     

百草枯在碳纳米管与离子液体复合修饰电极上的电化学行为及测定

制备了碳纳米管(MWCNTs)和疏水性离子液体1-丁基-3-甲基咪唑六氟磷酸盐(BMIMPF6)复合修饰电极(MWCNTs-BMIMPF6/GCE),并采用红外光谱(IR)分别对MWCNTs、BMIMPF6及MWCNTs-BMIMPF6进行了表征。运用循环伏安法研究了百草枯(PQ)在该修饰电极上的电化学行为。结果表明,在pH7.0的PBS缓冲溶液中,PQ在MWCNTs-BMIMPF6/GCE上出现2对明显的氧化还原峰,在20~200 mV/s扫描速率范围内,其氧化还原峰电流均与扫描速率平方根(v1/2)呈线性关系,表明该电极过程受扩散控制。计算了电极过程的部分动力学参数:电极有效面积A=0.156 4 cm2,百草枯在pH7.0的PBS缓冲液中的扩散系数D=7.0×10-5cm2/s。优化了方波溶出伏安法(SWSV)的实验参数,发现峰电流Ipa1与PQ浓度在7.729×10-7~9.660×10-5mol/L范围内呈线性关系,检出限为1.576×10-7mol/L。采用该方法对实际水样进行检测,增敏回收率为93%~104%。     

An Ionic Liquid Bulk-Modified Carbon Paste Electrode and Its Electrocatalytic Activity toward p-Aminophenol

An ionic liquid bulk-modified carbon paste electrode （M-CPE） has been fabricated by using 1-heptyl-3-methylimidazolium bromide as a modifier. Cyclic voltammetry （CV） and differential pulse voltammetry （DPV） were used to evaluate the electrocatalytic activity of the proposed electrode by choosing p-aminophenol （p-AP） as a model compound. Both at a bare carbon paste electrode （CPE） and the M-CPE, p-AP yielded a pair of redox peaks in 0.1 mol·L^-1 phosphate buffer solution （PBS, pH 7.0）. At the CPE, the peak-to-peak potential separation （AEp） was 0.233 V, while at the M-CPE the AEp was decreased to 0.105 V. Furthermore, the current response to p-AP at the M-CPE was 10.2 times of that at the CPE by DPV. The electron transfer rate constant （ks） ofp-AP at the M-CPE was 13.3 times of that at the CPE. Under the optimal condition, a linear dependence of the catalytic current versus p-AP concentration was obtained in the range of 2.0× 10^- 6 to 3.0× 10^- 4 mol·L^-1 with a detection limit of 6.0× 10^-7 mol·L^-1 by DPV. In addition, compared to other modified method the proposed electrode exhibited distinct advantages of simple prapartion, surface renewal, good reproducibility and good stability. It has been used to determine p-AP in simulated wastewater samples.     

Sensitive and Simple Electrochemical Detection of Lead(II) with Carbon Ionic Liquid Electrode

In this paper a carbon ionic liquid electrode (CILE) was fabricated by using ionic liquid 1‐ethyl‐3‐methylimidazolium ethylsulphate ([EMIM]EtOSO₃) as the modifier and further used as the working electrode for the sensitive anodic stripping voltammetric detection of Pb²⁺. The characteristics of the CILE were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). In pH 4.5 NaAc‐HAc buffer Pb²⁺ was accumulated on the surface of CILE due to the extraction effect of IL and reduced at a negative potential (‐1.20 V). Then the reduced Pb was oxidized by differential pulse anodic stripping voltammetry with an obvious stripping peak appeared at ?0.67 V. Under the optimal conditions Pb²⁺ could be detected in the concentration range from 1.0 × 10^?8 mol/L to 1.0 × 10^?6 mol/L with the linear regression equation as I_p(μA) = ?0.103 C (μmol/L) + 0.0376 (γ = 0.999) and the detection limit as 3.0 × l0^?9 mol/L (3σ). Interferences from other metal ions were investigated and Cd²⁺ could be simultaneously detected in the mixture solution. The proposed method was further applied to the trace levels of Pb²⁺ detection in water samples with satisfactory results.     

对乙酰氨基酚在活化玻碳电极上的电化学行为及测定

应用循环伏安法,研究了对乙酰氨基酚(PCT)在活化玻碳电极上的电化学行为.在pH=4.00的HAc-NaAc缓冲溶液中,PCT的CV扫描于0.54 V左右出现一对明显的氧化-还原峰.电极反应为2电子、2质子的受吸附控制的准可逆过程.其氧化峰电流与PCT浓度在8.00×10-6~2.00×10-4mol.L-1范围内呈良好的线性关系,相关系数r=-0.99918;检出限为6.34×10-6mol.L-1.用于药物样品PCT的含量测定,结果满意.     

The Electrochemical Behavior and the Determination of Bavistin on Glassy Carbon Electrode

Bavistin(MBC)'isatypeofveryimportantbactericides.Theanalyticalmethodsofthispesticideincludingchromatography',polarography'havebeenreported,butthereisnoreportaboutthedetendnationwithvoltanuntryonglassycarbonelectrode.Inthispaper,westudiedthevoltanunetric(CV)propertiesandthedifferentialpulsestrippingvoltanunetry(DPSV)detendnationofMBConglassycarbonelectrode.TheinstrUmentusedinthisexperimentwastheBAS-l(X)AElectroanalyser.Aglassycarbonelectrodewasusedastheworkingelectrode,aconunercialAgjA…     

Effect of Ionic Liquid Structure on the Electrochemical Response of Dopamine at Room Temperature Ionic Liquid‐modified Carbon Paste Electrodes (IL–CPE)

In this work 12 different ionic liquids (ILs) have been used added as co‐binders in the preparation of modified carbon paste electrodes (IL–CPEs) used for the voltammetric analysis of dopamine in Britton‐Robinson buffer. The ionic liquids studied were selected based on three main criteria: (1) increasing chain length of alkyl substituents (studying 1‐ethylimidazolium and ethyl, propyl, butyl, hexyl and decylmethylimidazolium bis(trifluoromethylsulfonyl)imide ionic liquids); (2) nature of the counter ion (dicyanamide, bis(trifluoromethylsulfonyl)imide and hexafluorophosphate) in 1‐butyl‐3‐methylimidazolium ionic liquids; and (3) cation ring structures (1‐butyl‐3‐methylimidazolium, 1‐butyl‐1‐methylpiperidinium, 1‐butyl‐1‐methylpyrrolidinium and 1‐butyl‐3‐methylpyridinium) in bis(trifluoromethylsulfonyl)imide or hexafluorophosphate (1‐butyl‐3‐methylimidazolium or 1‐butyl‐3‐methylpyridinium as cations) ionic liquids. The use of IL as co‐binders in IL–CPE results in a general enhancement of both the sensitivity and the reversibility of dopamine oxidation. In square wave voltammetry experiments, the peak current increased up to a 400 % when 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide was used as co‐binder, as compared to the response found with the unmodified CPE. Experimental data provide evidence that electrostatic and steric effects are the most important ones vis‐à‐vis these electrocatalytic effects on the anodic oxidation of dopamine on IL–CPE. The relative hydrophilicity of dicyanamide anions reduced the electrocatalytic effects of the corresponding ionic liquids, while the use of 1‐ethyl‐3‐methylimidazolium hexafluorophosphate or 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (two relatively small and highly hydrophobic ionic liquids) as co‐binders in IL–CPE resulted in the highest electrocatalytic activity among all of the IL–CPE studied.     

Electrochemical Determination of Ascorbic Acid in Room Temperature Ionic Liquid BPPF6 Modified Carbon Paste Electrode

A room temperature ionic liquid N‐butylpyridinium hexafluorophosphate (BPPF₆) was used as a binder to make an ionic liquid modified carbon paste electrode (IL‐CPE), which showed good characteristics such as simple preparation procedure, fast electrochemical response and good conductivity. The electrochemical oxidation of ascorbic acid (AA) on the new IL‐CPE was carefully studied. The oxidation peak potential of AA on the IL‐CPE appeared at 109 mV (vs. SCE), which was about 338 mV decrease of the overpotential compared to that obtained on the traditional carbon paste electrode (CPE) and the oxidation peak current was increased for about four times. The electrochemical parameters of AA on the IL‐CPE were calculated with the charge transfer coefficient (α) and the electrode reaction rate constant (k_s) as 0.87 and 0.800 s^?1, respectively. Based on the relationship of the oxidation peak current and the concentration of AA a sensitive analytical method was established with cyclic voltammetry. The linear range for AA determination was in the range from 1.0×10^?5 to 3.0×10^?3 mol/L with the linear regression equation as I_p (μA)=?2.52–0.064C (μmol/L) (n=13, γ=0.9942) and the detection limit was calculated as 8.0×10^?6 mol/L (3σ). The proposed method was free of the interferences of coexisting substances such as dopamine (DA) and amino acids etc., and successfully applied to the vitamin C tablets determination.     

Electrochemical Behaviour of Iron in a Third‐Generation Ionic Liquid: Cyclic Voltammetry and Micromachining Investigations

The electrochemical behaviour of Fe in 1‐ethyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim]⁺Ntf2^?) and mixtures with Cl^? is studied with the aim of investigating the applicability of ionic liquids (IL) for the electrochemical machining of iron. Whereas in pure IL iron could not be significantly dissolved, the addition of Cl^? enables the active dissolution with anodic current densities up to several mA cm^?2. Although several anodic peaks appear in the cyclic voltammograms (CV), the distinct assignment of those electrochemical processes remain difficult. In particular no proof for the formation of FeCl_x^2?x complexes during Fe dissolution are deduced from the CV, although such complexes are shown to be stable in the employed electrolyte. In addition, we present electrochemical drilling experiments with short potential pulses, which demonstrate that electrochemical machining of Fe is, in principle, possible in IL based electrolytes, even though hampered by slow machining speed.