Identification of isomeric N-glycan structures by mass spectrometry with 157 nm laser-induced photofragmentation

Characterization of structural isomers has become increasingly important and extremely challenging in glycobiology. This communication demonstrates the capability of ion-trap mass spectrometry in conjunction with 157 nm photofragmentation to identify different structural isomers of permethylated N-glycans derived from ovalbumin without chromatographic separation. The results are compared with collision-induced dissociation (CID) experiments. Photodissociation generates extensive cross-ring fragment ions as well as diagnostic glycosidic product ions that are not usually observed in CID MS/MS experiments. The detection of these product ions aids in characterizing indigenous glycan isomers. The ion trap facilitates MS(n) experiments on the diagnostic glycosidic fragments and cross-ring product ions generated through photofragmentation, thus allowing unambiguous assignment of all of the isomeric structures associated with the model glycoprotein used in this study. Photofragmentation is demonstrated to be a powerful technique for the structural characterization of glycans.     

Trace determination of antifouling compounds by on-line solid-phase extraction-gas chromatography-mass spectrometry

A new method based on solid-phase extraction (SPE) on-line coupled to gas chromatography-mass spectrometry through an on-column interface has been applied to determine three antifouling compounds in water samples. Parameters affecting the SPE process and transfer step have been optimised and the method developed has been applied to the analysis of marinas, fishing ports and Ebro river water. The method allows the analytes to be detected at 0.01 microgram l-1 in SIM acquisition mode by preconcentrating only 10 ml of water sample. Different marina and fishing port water samples have been analysed and Irgarol 1051 has been found in some of them at a concentration level equal or lower than 0.05 microgram l-1.     

Full-range analysis of ambient volatile organic compounds by a new trapping method and gas chromatography/mass spectrometry

This study investigated the feasibility of analyzing a full range of ambient volatile organic compounds (VOCs) from C(3) to C(12) using gas chromatograph mass spectrometry (GC/MS) coupled with thermal desorption. Two columns were used: a PLOT column separated compounds lighter than C(6) and a DB-1 column separated C(6)-C(12) compounds. An innovative heart-cut technique based on the Deans switch was configured to combine the two column outflows at the ends of the columns before entering the MS. To prevent the resolved peaks from re-converging after combining, two techniques were attempted (hold-up vs. back-flush) to achieve the intended "delayed" elution of heavier components. Thus, the resulting chromatogram covering the full range of VOCs is a combination of two separate elutions, with the heavier section following the lighter section. With the hold-up method, band-broadening inevitably occurred for the delayed C(6)-C(7) DB-1 compounds while the light compounds eluted from the PLOT column. This broadening problem resulted in peak tailing that was largely alleviated by adding a re-focusing stage while the DB-1 compounds were back-flushed, and this modified technique is referred to as the back-flush method. With this modification, the separation of the C(6)-C(7) compounds improved dramatically, as revealed by the decrease in peak asymmetry (As) and increase in resolution. Linearity and precision for these peaks also improved, yielding R(2) and RSD values better than 0.9990 and 2.8%, respectively.     

Selective detection of sulfur-containing compounds by gas chromatography/chemical reaction interface mass spectrometry

Addition of a reactant gas to a low pressure microwave-induced plasma creates a reaction interface in which complex molecules are converted into small polyatomic neutral species. For a given reactant gas the array of these small molecules reflect s the elemental composition of the original analyte. In this study HCI has been found highly effective as a reactant gas for selective detection of sulfur-eontaining compounds using capillary gas chromatography/ chernical reaction interface mass spectrometry. Detection limits as low as 30 pg of a sulfur-containing compound and a dynamic range of two orders of magnitude were achieved.     

Steroid profiles determined by capillary electrochromatography, laser-induced fluorescence detection and electrospray-mass spectrometry

Macroporous, monolithic capillary electrochromatography (CEC) columns, featuring a hydrophobic stationary phase, have been applied to the separations of steroids with good column efficiency. Using isocratic and gradient elution runs, mixtures of neutral or conjugated steroids could be resolved. While dansylated ketosteroids were detectable through laser-induced fluorescence at attomole levels, the CEC columns coupled to electrospray-ion-trap mass spectrometry featured femtomole detection limits.     

Catalytic destruction of brominated aromatic compounds studied in a catalyst microbed coupled to gas chromatography/mass spectrometry

The capability of solid porous catalysts has been studied for the destruction or modification of halogenated aromatic compounds contaminating the pyrolysis oil of recycled plastics from electronic waste. A fast and simple experimental procedure is carried out using a micropyrolyser coupled to GC-MS in such a way that catalyst microbed was placed in the sample tube of the pyrolyser. The pyrolysis products of polycarbonate blended with a frequently applied flame retardant tetrabromobisphenol A (TBBPA) and epoxy resin containing TBBPA monomer units have been analysed, and the brominated components were compared with the thermal decomposition products of TBBPA and its diallyl ether. When TBBPA vapour passes through molecular sieve 4A a slight debromination and a partial cleavage of bisphenol A into phenols occur. Over molecular sieves of larger pore size (13X and NaY zeolite) an important decrease of TBBPA amount is observed indicating effective trapping ability of these catalysts of basic character for brominated aromatic compounds. A total chemical modification of the vapour was achieved by Al-MCM-41 catalyst that split TBBPA into bromophenols. Analogous results were obtained by carrying out similar experiments on diallyl ether of TBBPA. Moreover, it was revealed that brominated bisphenol A compounds are modified essentially the same way, either evaporated or evolved from a polycarbonate blend or produced by pyrolysis from an epoxy resin.     

等离子体常压解吸离子源质谱

近年来,常压开源质谱解吸/离子化(ambient desorption/ionization mass spectrometry)技术的开发促进了质谱分析的蓬勃发展.作为常压开源质谱技术的一大重要分支,基于等离子体的常压质谱解吸/离子化技术因无需样品预处理、无溶剂化过程、高灵敏度、高通量、能实时在线检测样品等优点,受到了学术界及仪器制造、化学和生物分析等相关产业界的广泛关注.本文从离子源的种类、原理及应用等角度对目前我国在开源质谱领域中自主研发的基于等离子体的常压离子源的研究进展进行了总结,并对此类等离子体常压离子源的发展进行了展望,重点涉及微波等离子体源、常压微辉光放电等离子体源和解吸电晕束离子源.     

Postcolumn derivatization liquid chromatography/mass spectrometry for detection of chemical-weapons-related compounds

Postcolumn derivatization for liquid chromatography/mass spectrometry (LC/MS) analysis was characterized for detection of some compounds related to chemical-weapons (CW) agents using an Atmospheric Pressure Chemical Ionization (APCI) source. The derivatizing reagents were added directly to the LC eluent flow, and the derivatization reactions occurred in the APCI source under typical operating conditions. The compound S-[2-(diisopropylamino)ethyl] methylphosphonothioic acid was methylated using the derivatizing reagent trimethylphenyl ammonium hydroxide (TMPAH). Methylphosphonic acid was doubly derivatized to form dimethyl methylphosphonate, although the signal for the derivatization product was very sensitive to the amount of TMPAH. Arsenic compounds related to the CW agent lewisite, including chlorovinyl arsonous acid and arsenic (III) oxide, were derivatized using 2-mercaptopyridine. The thiol group reacted readily with the arsenic (III) center and provided a significant improvement in sensitivity relative to the underivatized signal using APCI or electrospray ionization. Triethanolamine and ethyl diethanolamine were derivatized with benzoyl chloride, a commonly used LC derivatizing reagent for alcohols, to modify their mass spectra. Postcolumn derivatization using an APCI source gives an alternative for detecting some difficult-to-ionize compounds. It has the limitations that sensitivity was not always improved even though the major mass spectral peaks can be shifted; it is necessary to carefully select the reagent; and some reagents introduced strong interference peaks at specific masses in the spectrum and may suppress the ionization of some derivatized analyte ions. The reagent also produced contamination in the source, which had to be cleaned daily.     

Two-dimensional on-line detection of brominated and iodinated volatile organic compounds by ECD and ICP-MS after GC separation

Inductively coupled plasma-mass spectrometry (ICP-MS) was coupled to a gas chromatographic (GC) system with electron capture detector (ECD), which enables relatively easy characterization and quantification of brominated and iodinated (halogenated) volatile organic compounds (HVOCs) in aquatic and air samples. The GC-ECD system is connected in series with an ICP-MS by a directly heated transfer line and an outlet port-hole for elimination of the ECD make-up gas during ignition of the plasma. The hyphenated GC-ECD/ICP-MS system provides high selectivity and sensitivity for monitoring individual HVOCs under fast chromatographic conditions. The ECD is most sensitive for the detection of chlorinated and brominated but the ICP-MS for iodinated compounds. The greatest advantage of the use of an ICP-MS is its element-specific detection, which allows clear identification of compounds in most cases. The absolute detection limits for ICP-MS are 0.5 pg for iodinated, 10 pg for brominated, and 50 pg for chlorinated HVOCs with the additional advantage that calibration is almost independent on different compounds of the same halogen. In contrast to that detection limits for ECD vary for the different halogenated compounds and lie in the range of 0.03-11 pg. The two-dimensional GC-ECD/ICP-MS instrumentation is compared with electron impact mass spectrometry (EI-MS) and microwave induced plasma atomic emission detection (MIP-AED). Even if EI-MS has additional power in identifying unknown peaks by its scan mode, the detection limits are much higher compared with GC-ECD/ICP-MS, whereas the selective ion monitoring mode (SIM) reaches similar detection limits. The MIP-AED detection limits are at the same level as EI-MS in the scan mode.     

热脱附-气相色谱-三重四极杆串联质谱法测定环境空气中的挥发性有机物

采用热脱附(TD)结合气相色谱-三重四极杆串联质谱(GC-MS/MS)建立了环境空气中23种挥发性有机物(VOCs)同时检测的分析方法。空气样品通过主动采样的方式富集到装有Tenax-TA填料的热脱附管中,热解吸后在选择反应监测(SRM)模式下用GC-MS/MS进行检测,内标法定量。结果表明,23种VOCs在0.01~1 ng和1~100 ng低、高两个范围内线性关系良好,相关系数(r²)均大于0.99,方法定量限为0.00008~1 μ g/m³。加标水平为2、10和50 ng时,23种VOCs的平均回收率为77%~124%。除了最低加标水平的氯苯,相对标准偏差(RSD, n=6)均小于20%。对市内3个采样点的环境空气进行测定,其中苯、甲苯、乙苯、二甲苯、苯乙烯、1,2,4-三甲基苯和六氯丁二烯均有检出。实验证明,该TD和GC-MS/MS相结合的检测方法具有准确、可靠、灵敏度高等优点,适用于环境空气中VOCs的同时测定。     

Gas chromatography/tandem mass spectrometry method for the simultaneous analysis of 19 brominated compounds in environmental and biological samples

A methodology for the simultaneous analysis of eight polybrominated diphenyl ethers (PBDEs); eight methoxylated PBDEs (MeO-PBDEs); and three emerging flame retardants, hexabromobenzene (HBB), pentabromoethyl benzene (PBEB), and decabromodiphenyl ethane (DBDPE) by gas chromatography coupled to tandem mass spectrometry (GC-MS-MS) was developed for two environmental matrices (sediment and sludge) and three biological matrices (fish, dolphin blubber, and bird eggs). The use of selective reaction monitoring (SRM) allows a high selectivity, which is critical in the analysis of complex samples like blubber. Analytical parameters such as linearity, reproducibility, or accuracy were evaluated. Method limits of detection and quantification were evaluated and compared with GC-EI-MS and GC-NCI-MS. Method detection limits were valid for the environmental analysis in all cases, with values between 0.01 and 1.65 ng/g dw for sediment, 0.05 and 2.78 ng/g dw for sludge, 0.04 and 10.6 ng/g lw for fish, 0.01 and 1.11 ng/g lw for dolphin blubber, and 0.03 and 3.20 ng/g lw for bird eggs. The developed method was applied to five samples of each matrix. PBDEs were detected in all samples, while MeO-PBDEs were only detected in dolphin blubber. DBDPE was detected in sediment and sludge.     

Determination of oxygenated volatile organic compounds in ambient air using canister collection-gas chromatography/mass spectrometry.

This research attempts to establish a method to measure 11 kinds of oxygenated volatile organic compound (OVOC) in ambient air by using the canister collection-gas chromatography/mass spectrometry (GC/MS) method. Since several compounds such as acetone exhibited high blank concentrations due to their laboratory use, stringent quality control was conducted for the VOC-free added water and the VOC-free nitrogen gas. In order to prevent the decline of recovery rates due to lack of sufficient relative humidity, it is necessary to add VOC-free water when pressurizing and diluting the air samples. Thus, all the target compounds in ambient air were obtained from the canisters at high recovery rates without significant contamination. Furthermore, the canister collection-GC/MS method makes it possible to apply simultaneous air monitoring of OVOCs as well as volatile hazardous air pollutants without additional sampling.     

Stability of Th(IV) polymers measured by electrospray mass spectrometry and laser-induced breakdown detection

The formation of polynuclear thorium hydroxide complexes in acidic aqueous solutions is observed by electrospray mass spectrometry. Size, number of hydroxide ligands and charge of all complexes in solution are identified independently. By repeated measurements over a time span of up to 418 days the stability of the polymers is observed. At concentrations above [Th(IV)]_tot = 10 mM pentamers and dimers are the dominant stable species. In contrast, the fractions of pentamers initially present at [Th(IV)]_tot = 0.2 mM decrease within less than 4 weeks, correlated with the formation of nm-sized colloids observed by LIBD indicating an Ostwald-ripening like process.     

Trace analysis of tiamulin in honey by liquid chromatography-diode array-electrospray ionization mass spectrometry detection

A liquid chromatography with diode array or electrospray ionisation mass spectrometry detection (LC-DAD-ESI-MS) method for the determination of tiamulin residues in honey is presented. The procedure employs a solid-phase extraction (SPE) on polymeric cartridges for the isolation of tiamulin from honey samples diluted in aqueous solution of tartaric acid. Chromatographic separation of the tiamulin is performed, in isocratic mode, on a C18 column using methanol and ammonium carbonate 0.1% in water, in proportion (30:70, v/v). Average analyte recoveries were from 88 to 106% in replica sets of fortified honey samples. The LC-ESI-MS method detection limits differ from 0.5 microg kg(-1) for clear honeys to 1.2 microg kg(-1) for dark honeys. The developed method has been applied to the analysis of tiamulin residues in multifloral honey samples collected from veterinary treated beehives.     

Multi-residue screening of chlorinated and brominated compounds from aquaculture samples using matrix solid-phase dispersion--gas chromatography-mass spectrometry

An effective multiresidual method for the trace analysis of fifteen compounds from a diverse group of pesticides, polybrominated diphenyl ethers (PBDEs), polychlorinated biphenyl (PCBs) and polybrominated biphenyl (PBBs) in aquaculture feed is described. The analytical procedure is based on the matrix solid-phase dispersion (MSPD) of feed sample and subsequent elution with hexane. The MSPD process was evaluated using an asymmetrical experimental design 2(3)3(2)//9. Factors such as C18 sorbent amount, kind of adsorbents, solvent volume and elution mode were considered. The results suggest that the operational MSPD conditions are elution with pressure, 1 g of C18, basic alumina as adsorbent and 30 mL of hexane. The overall method including MSPD procedure and GC coupled to mass spectrometry (MS/MS) has been applied to several samples of aquaculture feed and marine species. Precision and accuracy of the analytical method were determined using the reference material from the International Atomic Energy Agency (IAEA-406), showing a good agreement to the referenced values.     

Method development for the determination of coumarin compounds by capillary electrophoresis with indirect laser-induced fluorescence detection

A capillary zone electrophoresis (CZE) with indirect laser-induced fluorescence detection (ILIFD) method is described for the simultaneous determination of esculin, esculetin, isofraxidin, genistein, naringin and sophoricoside. The baseline separation was achieved within 5 min with running buffer (pH 9.4) composed of 5mM borate, 20% methanol (v/v) as organic modifier, 10(-7)M fluorescein sodium as background fluorophore and 20 kV of applied voltage at 30 degrees C of cartridge temperature. Good linearity relationships (correlation coefficients >0.9900) between the second-order derivative peak-heights (RFU) and concentrations of the analytes (mol L(-1)) were obtained. The detection limits for all analytes in second-order derivative electrophoregrams were in the range of 3.8-15 microM. The RSD data of intra-day for migration times and second-order derivative peak-height were less than 0.95 and 5.02%, respectively. This developed method was applied to the analysis of the courmin compounds in herb plants with recoveries in the range of 94.7-102.1%. In this work, although the detection sensitivity was lower than that of direct LIF, yet the method would extend the application range of LIF detection.     

Fiber optic sensor for laser-induced room-temperature phosphorescence detection of polycyclic aromatic compounds

The development of a fiber optic sensor for the analysis of polycyclic aromatic compounds based on laser-induced room-termperature phosphorimetry is reported for the first time. A pulsed nitrogen laser was used to excite phosphorescence emission from compounds imbibed on filter-paper substrates. Thallium(I) acetate (0.1 M) was used to enhance phosphorescence emission from chrysene, 1,2-benzofluorene, 7,8-benzoquinoline, phenanthridine and 5,6-benzoquinoline. Lead(II) acetate (0.5 M) was employed for the determination of fluoranthene, which showed no phosphorescence signal on paper substrates pre-treated with thallium(I) acetate. Limits of detection at the ng/ml(-1) level were estimated for all the compounds. An improvement in the limits of detection of the nitrogen heterocyclic compounds was obtained by using a low-background paper substrate. Satisfactory reproducibility of measurements was observed, varying from 6.1% (chrysene) to 11.9% (7,8-benzoquinoline). The linear behavior of the sensor response was also evaluated. Linear dynamic ranges extend over two and three orders of magnitude and show the potential of the device for the quantitative analysis of environmental pollutants.