离子色谱法测定工业二氧化锆中氯离子

建立了工业二氧化锆中氯离子的超声分散–离子色谱检测法。采用超声分散的方式辅助萃取,超声后的样品经过0.22μm的滤膜过滤,取清液进行检测。以20 mmol/L氢氧化钾溶液作为流动相,流量为1.5 m L/min。该方法的检出限为0.000 2%,测定结果的相对标准偏差小于3%(n=6),加标回收率为92.0%~110.0%。与电位滴定法进行比对,两种方法检测结果相符。该方法简便准确,检出限低,有推广应用价值。     

气相色谱–质谱法测定白酒中的邻苯二甲酸酯类

采用气相色谱–质谱法对常见名贵白酒中的16种邻苯二甲酸酯类含量进行测定。将样品提取、净化后,经气相色谱–质谱联用仪进行分离测定。采用特征选择离子检测扫描(SIM),以色谱保留时间和色谱碎片的丰度比定性,以峰面积外标法定量。16种邻苯二甲酸酯类物质的含量与色谱峰面积在0~2.0μg/m L范围内线性良好,线性相关系数均在0.995以上,方法检出限为0.05 mg/L。16种邻苯二甲酸酯含量测定结果的相对标准偏差均小于10%(n=6),加标回收率为91.21%~105.22%。该方法样品前处理简单,灵敏度高,适用于同时定性及定量检测白酒中16种邻苯二甲酸酯。     

铌酸催化的苯甲醛与甲醇缩合反应

采用铌酸为催化剂,探索了该催化剂对苯甲醛与甲醇缩合反应的影响.优化反应条件是,催化剂用量为反应物质的量的5mol%,甲醇10mL(兼作溶剂),回流状态下反应2h,反应的产率和转化率分别达到94%、98.0%.该催化剂同样适用于其他醛(酮)与甲醇的缩合反应,可得到34%～89%的产率.所述方法操作简单、产率高、选择性好而且对环境友好,反应结束后,催化剂很容易回收,并能有效重复使用.     

液-液萃取气相色谱法测定地表水中痕量苯酚

建立了液-液萃取气相色谱法测定地表水中痕量苯酚的方法。用盐酸调节水样至pH2左右,以二氯乙烷-乙酸乙酯(体积比为2∶1)混合溶液为萃取剂,以CD-5色谱柱进行分离,氢火焰离子化检测器检测苯酚的含量。苯酚的质量浓度在1.00~20.0μg/L范围内与其色谱峰面积呈良好的线性关系,线性相关系数r=0.999 3,检出限为0.03μg/L。样品加标回收率为93.0%~97.0%,测定结果的相对标准偏差小于2%(n=7)。该方法检出限低,精密度和准确度高,操作简便,适用于地表水中微量苯酚的分析。     

液相色谱-电喷雾电离三级四极杆质谱法测定茶叶中6种烟碱类农药残留

应用液相色谱-电喷雾电离三级四极杆质谱(LC-ESI-MS/MS)方法测定茶叶中呋虫胺、噻虫嗪、噻虫胺、吡虫啉、啶虫咪和噻虫啉烟碱类农药残留.前处理方法包括添加同位素内标吡虫啉-D4,乙腈提取,再用活性碳和Oasis(HLB)固相小柱净化.该方法采用正离子方式,多反应监测每种烟碱类杀虫剂各两对离子进行定性、定量分析.方法在0.01～0.4 mg/kg范围内具有良好的线性关系.实验了3个添加水平0.02、0.04和0.2 mg/kg,回收率范围为80.1%～106.1%;相对标准偏差小于9.7%;方法检出限(LOQ)均为0.02 mg/kg.本方法简便、快速、准确,各项技术指标满足国内外法规的要求,可用于茶叶样品中烟碱类农药残留的确证检测.     

Characterization of dextrans by size-exclusion chromatography on unmodified silica gel columns, with light-scattering detection, and capillary electrophoresis with laser-induced fluorescence detection

Unmodified silica gel size-exclusion columns were used in an on-line combination with light-scattering detection for a size characterization of dextrans. The influence of electrostatic interactions on analyte retention was briefly investigated. Size-exclusion chromatography was also used for evaluation of the fluorescence labeling procedure for dextrans with 8-aminonaphthalene-1,3,6-trisulfonic acid. The derivatives obtained through this procedure were used for electrophoretic measurements with laser-induced fluorescence detection. A comparison between the size-exclusion data and capillary electrophoresis indicates that the effectiveness of fluorescent labeling decreases with molecular mass of the dextran analytes.     

在Bu_2SnO-Bu_3PO_4缩合物的存在下以端羟基聚醚增韧环氧树脂

工业中大量生产的端羟基聚醚 ,由于羟基的反应活性不够 ,不能直接用于增韧胺类固化的环氧树脂 .Bu2 SnO Bu3PO4 缩合物能催化羟基对环氧基的加成反应 .本文研究在Bu2 SnO Bu3PO4 缩合物Sn P6 70 0的存在下以端羟基聚四氢呋喃 (PTMG)增韧芳香胺 4,4′ 二氨基二苯砜 (DDS)固化的环氧树脂 .PTMG首先与环氧树脂反应生成嵌段共聚物 ,在固化时发生微相分离 .分散相的尺寸在有利于增韧的范围内 .PTMG在分子量与浓度适当时 ,能使树脂的断裂韧性大大提高 ;抗弯强度也有显著提高 ,而Tg 和模量略有降低 .     

气动雾化进样微波等离子体炬（MPT）原子荧光光谱法测定锌的研究

本文将水溶液雾化进样与微波等离子体炬原子荧光光谱法联用,建立了HCL-MPT-AFS测定Zn的新方法。讨论了实验条件的选择问题以及溶液中共存离子对测定Zn的影响,本文所推荐的方法具有较高的灵敏度和精密度,并将其用于实际样品分析。     

Electrochemical Detection of Artemisinin Using Cobalt Sulphide/Reduced Graphene Oxide Nanocomposite

Solvothermally synthesized cobalt sulphide/reduced graphene oxide (CoS/rGO) was used to fabricate an electrochemical sensor for detection of artemisinin. Microscopic techniques were used to characterize CoS/rGO nanocomposite. The electrochemical sensor was fabricated by modifying the surface of glassy carbon electrode with CoS/rGO nanocomposite. [Fe(CN)6]^3−/4− was used as a mediator to aid oxidation of artemisinin. Differential pulse voltammetric technique was used for the detection of artemisinin. A linear range of 30–100 μM was used. Experimentally, a detection limit of 0.5 μM was obtained. Therefore, the developed sensor can be used for quality control of artemisinin.     

气相色谱-质谱法测定纺织品中N-乙基全氟辛烷磺酰胺

提出了用气相色谱-质谱法测定纺织品中N-乙基全氟辛烷磺酰胺的方法。试样经甲醇超声提取后,在旋转蒸发仪中浓缩至5 mL,通过DB-5MS色谱柱分离,采用选择离子监测模式检测,定性离子为m/z69,108,131,169,448,定量离子为m/z108。N-乙基全氟辛烷磺酰胺的质量浓度在0.2~20.0 mg.L-1范围内与峰面积呈线性关系,检出限(3S/N)为0.69μg.L-1。用标准加入法做回收试验,测定平均回收率为97%。     

硅烷化衍生-气相色谱-质谱联用法测定橙汁粉中维生素C

橙汁粉样品用N,N-二甲基甲酰胺提取,并离心分离,所得上清液中抗坏血酸与六甲基二硅氨烷和三甲基氯硅烷进行衍生反应,产物用正庚烷萃取。萃取液加入棕榈酸甲酯作为内标,供气相色谱-质谱分析。在气相色谱分离中用HP-5MS毛细管柱(30 m×250μm,0.25μm)为固定相,在质谱测定中采用全扫描模式。硅烷化抗坏血酸标准与内标峰面积的比值与硅烷化抗坏血酸的质量在1.0～5.0 mg范围内呈线性关系。方法用于橙汁粉样品中维生素C的测定,橙汁粉中维生素C的平均质量分数(n=6)为0.195 4%,回收率在92.3%～98.5%之间。     

Polydopamine-modified MWCNTs-glassy Carbon Electrode,a Selective Electrochemical Morphine Sensor

An electrochemical sensor based on a glassy carbon electrode was prepared using f-MWCNTs and polydopamine. Several techniques were used to investigate the surface features. Voltammetric techniques were used to evaluate the electrocatalyst efficiency, and it was used for morphine determination using differential pulse voltammetry. Different parameters affecting the method‘s sensitivity and selectivity were optimized. The linear dynamic range was 0.075–75.0 μM with a detection limit of 0.06 μM morphine. Also, the method‘s selectivity was tested, which was proved to be satisfactory. Finally, the sensor was successfully used for morphine determination in human plasma and urine samples with acceptable results.     

改性沥青中橡胶含量的高效液相色谱测定法

用高效液相色谱法测定了改性沥青中橡胶的含量。柱温30℃,检测波长222 nm,流动相为同等比例的正己烷、四氢呋喃和乙腈的混合液,UV检测器。该方法的相对标准偏差RSD≤1.5%,线性方程:y=800.94x+579.03,线性相关系数r=0.999 8。     

Characterization of Peanut Oil by Infrared Spectroscopy with an Improved Gaussian Mixture Model

The Gaussian mixture model (GMM) and regression (GMR) are widely used statistical tools in pattern classification and nonlinear regression. In this paper, the suitability score was used for variable selection to improve GMM and GMR. The improved GMM was used to characterize peanut oil adulterated with palm oil using Fourier transform infrared spectroscopy. The improved GMR was applied to determine the concentration of palm oil contaminant present. As comparison, GMM and GMR with principal component analysis for feature extraction, support vector machine, back-propagation artificial neural network, nearest centroid classification, and partial least-squares analysis were also used to classify and quantify peanut oil. It was demonstrated that the method is a new classification and regression strategy for the detection of adulterated edible oil.     

Analysis of testosterone in human urine using molecularly imprinted solid-phase extraction and corona discharge ion mobility spectrometry

Analysis of testosterone was accomplished using corona discharge ion mobility spectrometry. Molecular imprinted polymer was used for the extraction and pre-concentration of testosterone. Analytical parameters including precision, dynamic range and detection limit were obtained. The linear dynamic range was from 10 to 250 ng/mL and the limit of detection was 0.9 ng/mL. The proposed method was used for analysis of testosterone in urine samples. A urine sample from a 3-year-old girl was used as the blank. The RSD was below 10%. The obtained results from the method were also compared with the standard method for analysis of testosterone using SPE-HPLC analysis. The results demonstrate the accuracy of the method.     

Qualitative and quantitative analysis of active flavonoids in Flos Lonicerae by capillary zone electrophoresis coupled with solid-phase extraction

Flavonoids are an important bioactive group in the commonly used herbal medicine Flos Lonicerae. A new method of capillary zone electrophoresis (CZE) coupled with solid-phase extraction (SPE) was developed for simultaneous assay of flavonoid aglycones and glycosides in Flos Lonicerae. Optimum CZE separation was achieved with a background electrolyte (BGE) solution consisting of 80 mM boric acid and 20 mM phosphate acid, adjusted to pH 8.1, with 15% acetonitrile (v/v) added, and applying a separation voltage of 28 kV. The SPE method was used for pretreating the complex matrix of botanical materials and good reproducibility was obtained when avicularin was used as internal standard. Linearity of the method was excellent with correlation coefficients (r2) in the range of 0.9995-0.9999 and detection limits were lower than 0.6 microg/mL for the four flavonoids. The obtained recoveries varied between 93 to 104% while the relative standard deviations (RSDs) were below 4.4% (n=3). The developed CZE method was successfully used for the separation of eight flavonoids and the quantification of the four flavonoids in five species of Flos Lonicerae.     

悬浮液进样-火焰原子吸收光谱法测定聚乙烯中的铜、镁

将悬浮液进样技术应用于火焰原子吸收光谱法成功地测定了聚乙烯中的镁、铜。将样品粉碎、过筛并悬浮在乙醇-Triton X-100溶液中制成悬浮液。通过在与样品悬浮液等体积的空白溶液中加入适量的乙二醇，可配制成与试液粘度一致的参比溶液。以Sr^2 作为镁的释放剂，以正丁醇为增敏试剂，用工作曲线法检测定。对悬浮剂的选择、干扰、线性范围及检出限进行了考察，方法简便、快速、准确。     

Determination of arsenic in sediments, coal and fly ash slurries after ultrasonic treatment by hydride generation atomic absorption spectrometry and trapping in an iridium-treated graphite tube

A simple and reliable method for the determination of arsenic in sediment and in coal without sample digestion, based on hydride generation from slurry samples is proposed. After grinding the samples to a particle size of 50 μm, the sample powder was mixed with aqua regia and hydrofluoric acid in an ultrasonic bath for 30 min. After diluting the mixture with hydrochloric acid, the slurry was allowed to stand for 48 h, and an aliquot was used for hydride generation with sodium borohydride. More than 80% of the arsenic was leached to the aqueous phase under these conditions, except for one sediment sample with very high silica content. The generated arsine was collected in a graphite tube, treated with 0.5 mg of iridium as a permanent modifier, and the arsenic determination was carried out by electrothermal atomic absorption spectrometry. The same tube could be used for at least 160 cycles without any re-treatment. The greatest advantage of the method was that only a minimum of reagents and sample handling were required, reducing the risks of contamination and/or analyte loss. However, the addition calibration technique had to be used in order to obtain results within the 95% confidence level for 11 certified reference materials, 5 sediments, 5 coals and one coal fly ash. One certified sediment slurry was spiked with the analyte and the resulting addition calibration curve was used for the analysis of the certified sediments. Similarly, one certified coal was used to obtain the addition calibration curve for the coal and coal fly ash samples. The recoveries of the certified values, except for one sediment, were between 91 and 115%. The limits of detection in the samples were 0.54 and 0.7 μg g⁻¹ for the coal and sediment samples, respectively, obtained for 1 ml of slurry containing 1 mg of sample.     

Determination of Hydrogen Sulfide by Wavelength-modulated Diode Laser Absorption Spectroscopy

Rapid, accurate, and sensitive determination of hydrogen sulfide was provided by tunable distributed feedback diode laser absorption spectroscopy. The laser wavelength scanning range covered the strongest absorption band of hydrogen sulfide. The absorption line at 1578?nm was used for analytical measurements. A homemade digital lock-in amplifier was used to demodulate the first and the second harmonic signals. Normalization of the second harmonic by the first harmonic signal provided calibration-free measurements so that interferences from light path, circuitry, and source intensity were minimized. A mass flow controller was used to introduce 0–100?ppm hydrogen sulfide for validating the analytical performance. The results demonstrated the linearity of the normalized harmonic signals with concentration with a correlation coefficient of 0.9995. The response time was approximately 3?s. The detection limit by Allan variance was 45 ppb with an integration time of 35?s. The sensitive hydrogen sulfide sensor is suitable for environmental monitoring with real-time detection.     

Fractionation analysis of magnesium in olive products by atomic absorption spectrometry

A scheme is presented for fractionation of olive components and magnesium determinations in different fractions. The charge of metal species was established using cation exchange with Dowex 50Wx8-40. The resin Amberlite XAD-4 was used for the separation of olive polyphenols in complexes with olive proteins and polysaccharides. The organic and inorganic fraction of magnesium was studied with different solvents as to its bioavailability properties. Flame and electrothermal atomic absorption spectrometry were used off-line for the determinations of magnesium in the different fractions obtained.