LiCoO_2 electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO2 electrode in 1 mol/L LiPF6-EC:DMC:DEC elec- trolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO2 electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO2 electrode in Li/LiCoO2 cells is attributed to the formation of a Li1-xCoO2/LiCoO2 concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO2 hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5.     

Effects of current densities on the formation of LiCoO<Subscript>2</Subscript>/graphite lithium ion battery

The activation characteristics and the effects of current densities on the formation of a separate LiCoO₂ and graphite electrode were investigated and the behavior also was compared with that of the full LiCoO₂/graphite batteries using various electrochemical techniques. The results showed that the formation current densities obviously influenced the electrochemical impedance spectrum of Li/graphite, LiCoO₂/Li, and LiCoO₂/graphite cells. The electrolyte was reduced on the surface of graphite anode between 2.5 and 3.6 V to form a preliminary solid electrolyte interphase (SEI) film of anode during the formation of the LiCoO₂/graphite batteries. The electrolyte was oxidized from 3.95 V vs Li⁺/Li on the surface of LiCoO₂ to form a SEI film of cathode. A highly conducting SEI film could be formed gradually on the surface of graphite anode, whereas the SEI film of LiCoO₂ cathode had high resistance. The LiCoO₂ cathode could be activated completely at the first cycle, while the activation of the graphite anode needed several cycles. The columbic efficiency of the first cycle increased, but that of the second decreased with the increase in the formation current of LiCoO₂/graphite batteries. The formation current influenced the cycling performance of batteries, especially the high-temperature cycling performance. Therefore, the batteries should be activated with proper current densities to ensure an excellent formation of SEI film on the anode surface.     

Impedance Studies of Spinel LiMn2O4 Electrode/electrolyte Interfaces

The formation process of solid electrolyte interphase（SEI） film on spinel LiMn2O4 electrode surface was studied by electrochemical impedance spectroscopy（EIS） during the initial storage in 1 mol/L LiPF6-EC：DMC：DEC electrolyte and in the subsequent first charge-discharge cycle. It has been demonstrated that the SEI film thickness increased with the increase of storage time and spontaneous reactions occurring between spinel LiMn2O4 electrode and electrolyte can be prevented by the SEI film. In the first charge-discharge cycle succeeding the storage, the electrolyte oxidation coupled with Li-ion insertion is evidenced as the main origin to increase the resistance of SEI film. The results also confirm that the variations of the charge transfer resistance（Rot） with the electrode potential（E） can be well described using a classical equation.     

Surface film formation on a graphite electrode in Li‐ion batteries: AFM and XPS study

The formation of a passivation film (solid electrolyte interphase, SEI) at the surface of the negative electrode of full LiCoO₂/graphite lithium‐ion cells using LiPF₆ (1M ) in carbonate solvents as electrolyte was investigated by means of x‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The analyses were carried out at different potentials of the first and the fifth cycles, showing the potential‐dependent character of the surface‐film species formation. These species were mainly identified as Li₂CO₃ up to 3.8 V and LiF up to 4.2 V. This study shows the formation of the SEI during charging and its partial dissolution during discharge. Copyright © 2005 John Wiley & Sons, Ltd.     

尖晶石锂锰氧化物电极首次脱锂过程的EIS研究

研究了尖晶石锂锰氧化物电极首次脱锂过程中的电化学阻抗特征. 通过选取适当的等效电路拟合实验所得的电化学阻抗谱数据, 获得了首次脱锂过程中固体电解质相界面膜(SEI膜)的电阻、电容以及电荷传递电阻、双电层电容等随电极极化电位的变化规律.     

Monitoring electrode/electrolyte interfaces of Li-ion batteries under working conditions: A surface-enhanced Raman spectroscopic study on LiCoO2 composite cathodes

Lithium-ion batteries are commonly used for electrical energy storage in portable devices and are promising systems for large-scale energy storage. However, their application is still limited due to electrode degradation and stability issues. To enhance the fundamental understanding of electrode degradation, we report on the Raman spectroscopic characterization of LiCoO₂ cathode materials of working Li-ion batteries. To facilitate the spectroscopic analysis of the solid electrolyte interface (SEI), we apply in situ surface-enhanced Raman spectroscopy under battery working conditions by using Au nanoparticles coated with a thin SiO₂ layer (Au@SiO₂). We observe a surface-enhanced Raman signal of Li₂CO₃ at 1090 cm⁻¹ during electrochemical cycling as an intermediate. Its formation/decomposition highlights the role of Li₂CO₃ as a component of the SEI on LiCoO₂ composite cathodes. Our results demonstrate the potential of Raman spectroscopy to monitor electrode/electrolyte interfaces of lithium-ion batteries under working conditions thus allowing relations between electrochemical performance and structural changes to be established.     

The understanding of solid electrolyte interface (SEI) formation and mechanism as the effect of flouro-o-phenylenedimaleimaide (F-MI) additive on lithium-ion battery

Solid electrolyte interface (SEI) is a critical factor that influences battery performance. SEI layer is formed by the decomposition of organic and inorganic compounds after the first cycle. This study investigates SEI formation as a product of electrolyte decomposition by the presence of flouro-o-phenylenedimaleimaide (F-MI) additive. The presence of fluorine on the maleimide-based additive can increase storage capacity and reversible discharge capacity due to high electronegativity and high electron-withdrawing group. The electrolyte containing 0.1 wt% of F-MI-based additive can trigger the formation of SEI, which could suppress the decomposition of remaining electrolyte. The reduction potential was 2.35 to 2.21 V vs Li/Li⁺ as examined by cyclic voltammetry (CV). The mesocarbon microbeads (MCMB) cell with F-MI additive showed the lowest SEI resistance (Rsei) at 5898 Ω as evaluated by the electrochemical impedance spectroscopy (EIS). The morphology and element analysis on the negative electrode after the first charge-discharge cycle were examined by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS). XPS result showed that MCMB cell with F-MI additive provides a higher intensity of organic compounds (RCH₂OCO₂Li) and thinner SEI than MCMB cell without an additive that provides a higher intensity of inorganic compound (Li₂CO₃ and Li₂O), which leads to the performance decay. It is concluded that attaching the fluorine functional group on the maleimide-based additive forms the ideal SEI formation for lithium-ion battery.     

Electrochemical SPM investigation of the solid electrolyte interphase film formed on HOPG electrodes

Solid electrolyte interphase (SEI) film formation on graphite electrodes was studied on highly oriented pyrolytic graphite (HOPG) in nonaqueous electrolyte by in situ electrochemical atomic force microscopy (AFM). For potentials negative to 0.7 V versus Li|Li⁺ a SEI film is formed on the HOPG electrode surface. After the first cycle the film is rough and covers the surface of the HOPG electrode only partially. After the second cycle the HOPG surface is fully covered by a compact film. The thickness of the SEI film was measured by increasing the pressure of the AFM tip and thus scraping a part of the electrode surface. In this way a thickness of about 25 nm was found for the SEI film formed after two scan cycles between 3 and 0.01 V versus Li|Li⁺.     

白藜芦醇对长期贮存锂离子电池电解液性能的影响

锂离子电池电解液从制造完成到使用,一般都会经历灌装、运输和贮存的过程,了解长期贮存过程对锂离子电池电解液性能的影响,对锂离子电池的生产具有一定的理论指导意义.本文运用电化学阻抗谱(EIS)测试并结合循环伏安法(CV)测试、充放电测试、扫描电子显微镜(SEM)等研究了1 mol.L-1 LiPF6-EC:EMC 基础电解...     

Direct electrochemistry of myoglobin in a room temperature ionic liquid aqueous solution and its catalysis to H<Subscript>2</Subscript>O<Subscript>2</Subscript>

Using 1-ethyl-2-methylimidazolium trifluoroacetate (EMImTfa) as the supporting electrolyte, a couple of well-defined and reversible redox peaks of Myb could be observed at the basal plane graphite (BPG) electrode through direct electron transfer between the protein and the BPG electrode, whose anodic and cathodic peak potentials were at −0.098 V and −0.144 V vs. Ag | AgCl, respectively. Both anodic and cathodic peak currents increased linearly with the potential scan rates. Compared with the supporting electrolyte of phosphate buffer solution, EMImTfa played an important role for the direct electron transfer between Myb and the BPG electrode. Further investigation suggested that Myb was adsorbed tightly on the surface of the BPG electrode in the presence of EMImTfa to form a stable, approximate monolayer Myb film. Myb adsorbed on the BPG electrode surface could retain its biological activity and showed a remarkable electrocatalytic activity for the reduction of H₂O₂ in an EMImTfa aqueous solution. Based on these, a third-generation biosensor could be constructed to directly detect the concentration of H₂O₂ in EMImTfa aqueous solution with a limit of detection of 3.24 × 10⁻⁸ M. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 3, pp. 363–368. The text was submitted by the authors in English.     

Yttria stabilized zirconia solid electrolyte surface modification with ZrO<Subscript>2</Subscript>, Y<Subscript>2</Subscript>O<Subscript>3</Subscript>, and ZrO<Subscript>2</Subscript> + 9 mol % Y<Subscript>2</Subscript>O<Subscript>3</Subscript> films

The surface of ceramic electrolyte ZrO₂ + 9 mol % Y₂O₃, hereinafter referred to as YSZ (abbreviated yttria stabilized zirconia), was modified with 0.1 to 0.2 μm oxide films of ZrO₂, Y₂O₃, and YSZ (same composition as substrate) by dip coating in alcohol solutions of the relevant salts and further annealing. The results of scanning electronic microscopy and X-ray diffraction evidence epitaxial film growth. By means of impedance spectroscopy at the temperatures of 500 to 600°C, the effect of YZS electrolyte surface modification with ZrO₂, Y₂O₃, and YSZ films to the polarization resistance of silver electrode was studied.     

电解液添加剂硫酸亚乙酯对锂离子电池性能的影响

在1 mol/L LiPF₆/碳酸乙烯酯+碳酸二甲酯+碳酸甲乙酯（体积比1∶1∶1）电解液中,采用恒流充放电测试、循环伏安法（CV）、扫描电子显微镜（SEM）、能量散射光谱（EDS）、电化学阻抗谱（EIS）等测试技术,研究了添加剂硫酸亚乙酯（DTD）对锂离子电池性能及石墨化中间相碳微球（MCMB）电极/电解液界面性质的影响。 结果表明,在电解液中引入体积分数0.01%DTD后,MCMB/Li电池可逆放电容量从300 mA·h/g提高至350 mA·h/g,电池总阻抗降低,循环稳定性提高。CV测试发现,在首次还原过程中,DTD在电极电位1.4 V左右（vs Li/Li⁺）发生电化学还原,参与了MCMB电极表面固体电解质相界面膜（SEI膜）的形成过程。 同时,DTD对LiMn₂O₄电极性能无不良影响。     

Electrochemical intercalation kinetics of lithium ions for spinel LiNi0.5Mn1.5O4 cathode material

The crystal structure and electrochemical intercalation kinetics of spinel LiNi_0.5Mn_1.5O₄ such as the resistance of a solid electrolyte interphase (SEI) film, charge transfer resistance (R _ct), surface layer capacitance, exchange current density (i ₀), and chemical diffusion coefficient are evaluated by Fourier transform infrared (FT-IR) and electrochemical impedance spectroscopy (EIS), respectively. FT-IR shows that LiNi_0.5Mn_1.5O₄ thus obtained has a cubic spinel structure, which can be indexed in a space group of Fd3m with a disordering distribution of Ni. EIS indicates that R _s is almost a constant at different states of charge. The thickness of SEI film increases with increasing of the cell voltage. R _ct values evidently decreases when lithium ions deintercalated from the cathode in the voltage range from OCV to 4.6 V, and R _ct value increases with increasing potential of deintercalation over 4.7 V. i ₀ varies between 0.2 and 1.6 mA cm^?2, and the solid phase diffusion coefficient of Li⁺ changed depending on the electrode potential in the range of 10^?11–10^?9 cm² s^?1.     

Studies on the effects of coated Li2CO3 on lithium electrode

Although a lithium metal anode has a high energy density compared with a carbon insertion anode, the poor rechargeability prevents the practical use of anode materials. A lithium electrode coated with Li₂CO₃ was prepared as a negative electrode to enhance cycleability through the control of the solid electrolyte interface (SEI) layer formation in Li secondary batteries. The electrochemical characteristics of the SEI layer were examined using chronopotentiometry (CP) and impedance spectroscopy. The Li₂CO₃-SEI layer prevents electrolyte decomposition reaction and has low interface resistance. In addition, the lithium ion diffusion in the SEI layer of the uncoated and the Li₂CO₃-coated electrode was evaluated using chronoamperometry (CA).     

Enhanced electrochemical performance of submicron LiCoO<Subscript>2</Subscript> synthesized by polymer pyrolysis method

Submicron LiCoO₂ was synthesized by a polymer pyrolysis method using LiOH and Co(NO₃)₂ as the precursor compounds. Experimental results demonstrated that the powders calcined at 800 °C for 12 h appear as well-crystallized, uniform submicron particles with diameter of about 200 nm. As a result, the as-prepared LiCoO₂ electrode displayed excellent electrochemical properties, with an initial discharge capacity of 145.5 mAh/g and capacity retention of 86.1% after 50 cycles when cycled at 50 mA/g between 3.5 and 4.25 V. When cycled between 3.5 and 4.5 V, the discharge capacity increased to 177.9 mAh/g with capacity retention of 85.6% after 50 cycles.     

An aqueous rechargeable lithium battery based on doping and intercalation mechanisms

An aqueous rechargeable lithium battery (ARLB) using an electroactive polymer, polypyrrole (PPy), as a negative electrode; a lithium ion intercalation compound LiCoO₂ as a positive electrode; and Li₂SO₄ aqueous solution as an electrolyte and its working mechanism are described. The charge/discharge process is associated with the doping/un-doping of anions at the negative electrode and intercalation/deintercalation of lithium ions at the positive electrode. The average output voltage of the PPy//LiCoO₂ battery is about 0.85 V. This battery exhibits excellent cycling performance. This new technology solves the major problem of poor cycling life of ARLBs and will provide a new strategy to explore advanced energy storage and conversion systems.     

Kinetics of Li-ion transfer reaction at LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>, LiCoO<Subscript>2</Subscript>, and LiFePO<Subscript>4</Subscript> cathodes

Kinetics of LiFePO₄, LiMn₂O₄, and LiCoO₂ cathodes operating in 1 M LIPF₆ solution in a mixture of ethylene carbonate and dimethyl carbonate was deduced from impedance spectra taken at different temperatures. The most striking difference of electrochemical impedance spectroscopy (EIS) curves is the impedance magnitude: tens of ohms in the case of LiFePO₄, hundreds of ohms for LiMn₂O₄, and thousands of ohms for LiCoO₂. Charge transfer resistances (R _ct) for lithiation/delitiation processes estimated from the deconvolution procedure were 6.0 Ω (LiFePO₄), 55.4 Ω (LiCoO₂), and 88.5 Ω (LiMn₂O₄), respectively. Exchange current density for all the three tested cathodes was found to be comparable (0.55–1·10^?2 mAcm^?2, T = 298 K). Corresponding activation energies for the charge transfer process, \( {E}_{ct}^{\#} \), differed considerably: 66.3, 48.9, and 17.0 kJmol^?1 for LiMn₂O₄, LiCoO₂, and LiFePO₄, respectively. Consequently, temperature variation may have a substantial influence on exchange current densities (j _o) in the case of LiMn₂O₄ and LiCoO₂ cathodes.     

Cu3V2O8 Nanoparticles as Intercalation‐Type Anode Material for Lithium‐Ion Batteries

Cu₃V₂O₈ nanoparticles with particle sizes of 40–50 nm have been prepared by the co‐precipitation method. The Cu₃V₂O₈ electrode delivers a discharge capacity of 462 mA h g^?1 for the first 10 cycles and then the specific capacity, surprisingly, increases to 773 mA h g^?1 after 50 cycles, possibly as a result of extra lithium interfacial storage through the reversible formation/decomposition of a solid electrolyte interface (SEI) film. In addition, the electrode shows good rate capability with discharge capacities of 218 mA h g^?1 under current densities of 1000 mA g^?1. Moreover, the lithium storage mechanism for Cu₃V₂O₈ nanoparticles is explained on the basis of ex situ X‐ray diffraction data and high‐resolution transmission electron microscopy analyses at different charge/discharge depths. It was evidenced that Cu₃V₂O₈ decomposes into copper metal and Li₃VO₄ on being initially discharged to 0.01 V, and the Li₃VO₄ is then likely to act as the host for lithium ions in subsequent cycles by means of the intercalation mechanism. Such an “in situ” compositing phenomenon during the electrochemical processes is novel and provides a very useful insight into the design of new anode materials for application in lithium‐ion batteries.     

Enhanced electrochemical performance of LiFePO4 cathode with the addition of fluoroethylene carbonate in electrolyte

The effect of the fluoroethylene carbonate (FEC) addition in electrolyte on LiFePO₄ cathode performance was investigated in low-temperature electrolyte LiPF₆/EC/PC/EMC (0.14/0.18/0.68). Cyclic voltammetry, electrochemical impedance spectroscopy, and charge/discharge tests were conducted in this work. In the presence of FEC, the polarization of LiFePO₄ electrode decreased both at room and low temperatures. Meanwhile, the exchange current density increased. The rate capability of LiFePO₄ electrode was greatly enhanced as well. The morphology of the solid electrolyte interphase (SEI) on LiFePO₄ surface was modified with the addition of FEC as confirmed by scanning electron microscopy measurement. A compact film with small impedance was formed on LiFePO₄ surface compared to the case of FEC-free. The compositions of the film were analyzed by X-ray photoelectron spectroscopic measurement. The contents of Li _x PO _y F _z , LiF, and the carbonate species generated from solvents decomposition were reduced. The modified SEI promoted the migration of lithium ion through the electrode/electrolyte interphase and enhanced the electrochemical performance of the cathode.     

In situ analysis of interfacial reactions between negative MCMB,lithium electrodes,and gel polymer electrolyte

The interfacial properties of mesocarbon-microbeads (MCMB) and lithium electrodes during charge process in poly (vinylidenefluoride-co-hexafluoropropylene)-based gel electrolyte were investigated by in situ Raman microscopy, in situ Fourier transform-infrared (FTIR) spectroscopic methods, and charge–discharge, electrochemical impedance spectroscopy techniques. For MCMB electrode, the series phase transitions from initial formation of the dilute stage 1 graphite intercalation compound (GIC) to a stage 4 GIC, then through a stage 3 to stage 2, and finally to stage 1 GIC was proved by in situ Raman spectroscopic measurement. The formation of solid electrolyte interface (SEI) films formed on MCMB and metal lithium electrode was studied by in situ reflectance FTIR spectroscopic method. At MCMB electrode surface, the solvent (mostly ethylene carbonate) decomposed during charging process and ROCO₂Li may be the product. ROCO₂Li, ROLi, and Li₂CO₃ were the main composites of SEI film formed on lithium electrode, not on electrodeposited lithium electrode or lithium foil electrode.