巡游电子系化合物La0.8Ce0.2(Fe1-xCox)11.4Si1.6的磁热效应

对制备的化合物La0.8Ce0.2(Fe1-xCox)11.4Si1.6(x=0.02,0.04,0.06)的相组成、巡游电子变磁转变(IEMT)特性和磁热效应(MCE)进行了研究。粉末X射线衍射结果表明,经1373 K真空退火处理7 d后,化合物La0.8Ce0.2(Fe1-xCox)11.4Si1.6(x=0.02,0.04,0.06)均为单相立方NaZn13型晶体结构。随着Co含量由x=0.02增加到x=0.06,样品的居里温度TC由207 K上升到277 K。在0~1.5 T磁场变化下,x=0.02,0.04,0.06时样品的最大磁熵变|ΔSM(T)|分别为40.17,12.60和7.65 J.kg-1.K-1,可见该化合物有巨大的磁熵变,而且随Co含量的增加最大磁熵变迅速减小。该化合物的巨大磁熵变来源于TC处的一级相变,以及在TC以上由磁场诱导IEMT,但由于Co原子对Fe原子的替代能够抑制变磁转变的发生,因此该系化合物最大磁熵变随Co含量的增加迅速减小。     

La15Fe77B8型储氢合金的结构和电化学性能

研究了快淬和退火态La15Fe77B8型储氢合金的组织结构和电化学性能。应用中频感应熔炼-快淬方法制备了La15Fe77B8型储氢合金,其组成为La15Fe2Ni72Mn7B2Al2。结构分析表明:快淬La15Fe2Ni72Mn7B2Al2合金为多相结构,包括LaNi5相、La3Ni13B2相和(Fe,Ni)相,快淬合金经1223 K保温3 h,然后在873 K保温3 h退火处理后,LaNi5相增加,La3Ni13B2相几乎消失,(Fe,Ni)相增加且形态变大。电化学测试表明,退火合金的最大容量(307 mAh.g-1)略小于快淬合金(309 mAh.g-1),而循环稳定性有所改善。退火合金电极的倍率放电能力(HRD)低于快淬合金,原因在于交换电流密度(I0)及氢在合金中的扩散系数(D)降低。快淬和退火合金电极在低温233 K时均能放出55%的容量。     

一级相变磁制冷材料LaFe_(11.6)Si_(1.4)合金的磁相变特性系统分析

以La Fe11.6Si1.4合金为研究对象,系统分析了该一级相变材料的居里温度(TC)、磁场诱导磁相变的临界磁场(HC)、磁化率(χ)、磁滞、磁熵变(ΔS)、制冷能力(RCP)等磁性特性。结果表明:温度诱导磁相变的居里温度和磁场诱导磁相变的临界磁场均随磁场呈线性增加,ΔTC和ΔH随磁场和温度的变化率的值分别为4.1 K·T-1和0.2 T·K-1。当合金处于纯铁磁态和顺磁态时熵变磁熵变几乎为零,但磁场诱导的磁相变,会导致某一定温度下合金磁熵变有一个突变。但合金最大熵变并不是随磁场的增加而线性增加,当磁场达到一定值后随磁场增加其值基本没有变化。不同模型计算的制冷能力均随磁场的增加而呈线性增加。在两相共存态中,同一温度下两种不同铁磁的磁化率存在差异,即因磁场诱导的铁磁态相与合金中本身的铁磁态相的磁化率存在差异,且前者小于后者,这种物理现象对深入研究温度诱导和磁场诱导磁相变的差异有一定的参考价值。     

不同工艺和原料对Mn_(1.2)Fe_(0.8)P_(0.48)Si_(0.52)化合物磁热效应的影响

用不同的工艺和原料制备了3个名义成分相同的Mn1.2Fe0.8P0.48S i0.52化合物。X射线衍射结果表明,3个化合物均为Fe2P型六角结构(空间群为P-62m),并且存在少量的(Fe,Mn)3S i相。通过磁性测量发现,3个样品的居里温度有所不同,但是都在室温附近(270~290 K)。以Fe2P为原料制备的化合物具有较大的磁熵变,在1.5 T的磁场变化下其最大磁熵变为13.6 J.(kg.K)-1。以行星样品球磨机制备的化合物具有较小的热滞,最小热滞为6.7 K。这些表明不同的制备工艺和原料对化合物的居里温度、热滞和磁熵变都具有一定的影响。同时低成本的原料、简单的制备工艺、较小的热滞和较大的磁熵变使得Mn1.2Fe0.8P0.48S i0.52化合物成为一种理想的室温磁致冷候选材料。     

室温以上磁制冷材料La(Fe1-xCox)11.7Al1.3化合物的研究

通过X射线衍射分析和超导量子干涉磁强计（SQUID）磁性测量,研究了Co替代Fe含量对居里温度在室温以上的磁制冷材料La（Fe1-xCox）11.7Al1.3（x=0.072,0.081）磁结构和磁性能的影响。La（Fe1-xCox）11.7Al1.3材料的居里温度随Co的含量增加而增加,La（Fe0.919Co0.081）11.7Al1.3的居里温度为311 K。当外场变化为1.9 T时磁熵变达到3.6 J·kg^-1·K^-1,RCP值为168.6 J·kg^-1,虽然它的磁熵变小于具有巨磁熵变的磁制冷材料,但是它在磁场为1.9 T时的制冷能力与这些材料相当。     

添加镝的Nd-Fe-B纳米晶单相合金的微结构与磁性能研究

采用单辊快淬法制备了Nd12.3-xDyxFe79.7Zr0.8Nb0.8Cu0.4B6.0(x=0,0.5,1.5,2.5)合金纳米晶单相永磁薄带,研究了合金薄带晶化处理后,成分、组织结构与磁性能之间的关系.X射线衍射分析(XRD)表明,淬态合金主要由非晶相和Nd2Fe14B相组成,完全晶化后由Nd2Fe14B相和少量α-Fe组成.高分辨透射电镜(HRTEM)分析表明,经充分退火后,Nd2Fe14B晶体完整,晶粒间几乎没有边界相.随着Dy含量增加,晶粒尺寸细化,矫顽力大幅提高.x=0.5合金综合磁性能最佳,经过700℃晶化处理10min后,其磁性能为Jr=1.09 T,Hci=1048kA·m-1,(BH)max=169.5 kJ·m-3.     

快淬设备对Nd2Fe14B/α-Fe合金微结构和磁性能的影响

对比分析了感应喷射式熔旋快淬炉和电弧溢流式熔旋快淬炉在制备纳米双相Nd2Fe14B/α-Fe永磁材料方面的差异,研究了不同快淬设备对材料微结构和磁性能的影响. 结果表明:采用感应喷射式熔旋快淬炉制备的样品,表面较平整,厚度一致性好;而采用电弧溢流式熔旋快淬炉制备的样品,表面不平整,厚度一致性差. 对于相同的配方Nd10Fe79Zr1Co4B6,采用感应喷射式熔旋快淬炉制备的样品磁性能明显高于电弧溢流式熔旋快淬炉. 适当增加Zr含量,可以提高合金的非晶形成能力,有效削弱了电弧溢流式熔旋快淬炉冷却速率波动性较大对样品的负面影响,有助于提高磁性能.     

Gd7Pd3-xFex合金磁性及磁热效应的研究

采用电弧熔炼和高温退火的方法制备了Gd7Pd3-xFex(x=0, 0.2, 0.5, 0.8和1)合金材料,并对该系列合金材料的磁特性及磁热效应进行了研究。X射线粉末衍射研究表明,所有的材料均形成Th7Fe3型结构。并且随着x的增大,晶格常数、居里温度、饱和磁化强度和最大磁熵变均有所降低。相比于Gd7Pd3,掺入Fe元素的材料可以获得更接近室温的居里温度和更宽的工作温区,从而导致了7 T磁场下高达1096 J·kg^-1的相对制冷能力(RCP), Gd7Pd3-xFex有望被用于室温附近的磁制冷。     

镨元素对(Nd,Pr)10.5(FeCoZr)83.5B6合金显微结构和磁性能的影响

研究了稀土元素Pr对快淬(Nd1-xPrx)10.5(FeCoZr)83.5B6(x=0,0.2,0.4,0.6,0.8,1.0)合金显微组织结构和粘结磁体磁性能的影响。通过部分过快淬获得由非晶和微晶共同组成的条屑,在实验优化的退火条件下晶化处理后,制备出最佳磁性能的系列粘结磁体。随Pr含量的增加,磁体的内禀矫顽力Hci单调上升,剩磁Br单调下降,(BH)m在x=0.6～0.8处达到最大值70.6kJ·m-3。Pr元素使合金非晶态的晶化转变温度和转化能降低,合金的显微组织结构变得较粗大和较不均匀,从而使快淬粘结磁体剩磁降低,但Pr2Fe14B化合物较高的磁晶各向异性场使磁体的内禀矫顽力提高。     

快凝储氢合金La_(0.8)Ce_(0.2)Ni_(4.65-x)Mn_(0.9)Ti_(0.05)(V_(0.3)Fe_(0.4)Al_(0.3))_x微观结构和电化学性能研究

采用熔铸和快凝技术制备过计量比AB5.6型储氢合金La0.8Ce0.2Ni4.65-xMn0.9Ti0.05(V0.3Fe0.4Al0.3)x(x=0~1.0),研究了(V0.3Fe0.4Al0.3)对铸态和快凝合金相结构和电化学性能的影响。XRD和SEM结果表明:铸态合金组织由基体Ca Cu5型相和少量第二相组成;当x0.7时,快凝合金组织为计量比是AB5.5的Ca Cu5型单相组织,当x≥0.7后,合金中形成少量富La的La-Ni相;铸态与快凝合金的晶胞参数a,c及晶胞体积V均随x的增加而增加,快凝合金晶胞参数和晶胞体积明显大于铸态组织。室温(298 K)下铸态和快凝合金的放氢平台压随x的增加均依次降低,其中快凝合金放氢平台压降低幅度大。电化学测试结果表明:随x的增加,铸态和快凝合金电极的活化性能和最大放电容量均呈下降趋势,但电极循环稳定性逐渐提高;x=0.3~0.5时,快凝合金电极的最大放电容量为306~316 m Ah·g-1,经100次循环后的容量保持率S100达90%左右,快凝合金电极的循环寿命明显优于铸态合金。     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

Calculation of enthalpies of hydrogenation of hydrocarbons

Sets of hydrogen molecule equivalents have been developed which permit the calculation of hydrogenation of different types of carbon-carbon bonds from ab initio total energies (3-21G and 6-31G* basis sets, and, to a more limited extent, for MP2/6-31G* data) of reactants and products. The calculated enthalpies of hydrogenation are in good agreement with experiment for unstrained molecules, with average errors on the order of 2 kcal/mol. The 6-31G* equivalents allow the enthalpies for strained molecules to be calculated accurately, but the 3-21G equivalents do not. The equivalents for both basis sets have been tested by calculating the enthalpies of hydrogenation of carbon-carbon bonds in nitrogen- and oxygen-containing organic molecules, free radicals, and classical carbocations. The results are in good agreement with experiment in most cases.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。