考虑塑性应变记忆恢复的循环棘轮本构模型研究

在统一粘塑性循环本构理论框架下,以Ohno-Abdel-Karim非线性随动硬化模型为基础,建立了一个循环本构模型。模型通过引入塑性应变幅值记忆效应,并在塑性应变记忆项中加入恢复系数,提高了对循环硬化材料单轴棘轮行为的预言能力。将模型应用于316L不锈钢单轴棘轮行为的描述中,模拟不同平均应力、应力幅值下的棘轮应变,均与实验数据吻合较好,证明本文改进的本构模型能合理地描述循环硬化材料的单轴棘轮行为。     

纯铝在单轴应力循环作用下棘轮行为的试验研究

对纯铝进行了单轴应变控制和应力控制下的系统循环试验。对纯铝应变循环下的循环应变幅值、应变幅值历史、平均应变对循环特性的影响进行了揭示，对纯铝在非对称应力循环下的应力幅值、平均应力及其历史对循环蠕变〈即棘轮〉的影响进行了分析，得到了纯铝单轴循环行为的一些有意义的结果。     

304不锈钢室温和高温单轴循环塑性的实验研究

对304不锈钢进行了室温和高温单轴应变控制和应力控制下的系统循环试验。揭示和分析了循环应变幅值、平均应变及其历史和温度历史对材料应变循环特性的影响以及应力幅值、平均应力及其历史以及温度对循环棘轮行为的影响。也讨论了应变循环和应力循环间交互作用对材料循环塑性行为的影响。研究表明,无益单轴应变循环特性还是非对称单轴应力循环下的棘轮效应不仅取决于当前温度和加载状态,而且强烈依赖于其加载历史。研究得到了一些有助于304不锈钢室温和高温单轴循环行为本构描述的结果。     

退火和调质42CrMo合金钢单轴循环塑性行为的实验研究

在室温下对退火和调质42CrMo合金钢进行了单轴应变控制和应力控制的系统循环实验,并对它们的应变循环和应力循环特性进行比较.揭示和分析了应变幅值、平均应变及其历史对材料应变循环特性的影响以及应力幅值、平均应力及其历史对棘轮行为的影响.讨论了应变循环和应力循环间的交互作用以及不同热处理工艺下材料循环变形行为间的区别.研究发现材料的热处理工艺、平均应力和应力幅值及其历史对材料的棘轮行为都有很大的影响.得到了一些有助于进行合理本构描述的结果.     

内压循环下薄壁圆筒的环向棘轮应变预测

对单轴和比例加载下的棘轮应变进行预测目前仍有较大困难。本文考虑将移动极限面加入材料双面本构模型中，对原提出的叠加型随动强化律进行了修正，可以对较多循环数的1Crl8Ni9Ti不锈钢薄壁圆管的环向棘轮应变做出预测。     

循环软化45碳钢和循环硬化304不锈钢的棘轮行为实验研究

对循环软化45碳钢的单轴应力循环下的平均应力、应力幅值以及先前应变循环对棘轮效应的影响进行了实验研究;并对循环硬化的304不锈钢进行了多种非比例循环加载路径下路径形状、路径等效应力幅值、平均应变与平均应力对材料棘轮变形行为的影响实验.发现平均应力和应力幅值及其历史对于材料的棘轮行为都有很大的影响.     

一种考虑非比例附加损伤的多轴低周疲劳模型

在实际工作环境中,机械结构往往承受着多轴非比例循环载荷.相比多轴比例循环加载,多轴非比例循环加载由于产生了附加强化现象,造成机械结构疲劳寿命下降.通过分析薄壁圆筒管件在非比例加载工况下应力应变变化规律和发生破坏位置,本文基于临界面法提出一种考虑多轴非比例附加损伤的疲劳模型.该模型将最大剪切应变幅平面作为临界面,提出一个新的附加强化因子,结合临界面上切应变幅和正应变幅组成新的多轴疲劳损伤参量.此参量不仅考虑了非比例加载下临界面上正应变幅和切应变幅对材料造成的疲劳损伤,还考虑到应变路径的变化和材料非比例加载敏感特性对材料疲劳寿命的影响.考虑到实际情况下模型所需材料附加强化系数有时难以获得的情况,给出了材料附加强化系数的有关近似计算公式.只需要材料基本力学参数便可得到材料附加强化系数,方便工程实际应用.采用8种材料的多轴疲劳寿命数据对提出的新模型进行检验,结果表明所提出的新模型与传统多轴疲劳模型相比预测寿命精度更高.      

奥氏体不锈钢高温循环棘轮行为的实验研究

对两种不锈钢材料（316L和304）进行了高温应力控制下的系统循环试验。对该类材料在应力循环下的平均应力、应力幅值及其历史对循环蠕变（棘轮效应）的影响进行了分析,同时也分析了环境温度的变化以及先前应变循环对后继应力循环的棘轮行为的影响。研究表明,两种不锈钢材料在高温非对称循环下的单轴棘轮行为基本相同,不但依赖于当前温度和加载状态,而且还依赖于先前加载历史。研究得到了不锈钢材料高温单轴循环棘轮行为的一些有意义的结果。     

一种考虑非比例附加损伤的多轴低周疲劳模型

在实际工作环境中,机械结构往往承受着多轴非比例循环载荷.相比多轴比例循环加载,多轴非比例循环加载由于产生了附加强化现象,造成机械结构疲劳寿命下降.通过分析薄壁圆筒管件在非比例加载工况下应力应变变化规律和发生破坏位置,本文基于临界面法提出一种考虑多轴非比例附加损伤的疲劳模型.该模型将最大剪切应变幅平面作为临界面,提出一个新的附加强化因子,结合临界面上切应变幅和正应变幅组成新的多轴疲劳损伤参量.此参量不仅考虑了非比例加载下临界面上正应变幅和切应变幅对材料造成的疲劳损伤,还考虑到应变路径的变化和材料非比例加载敏感特性对材料疲劳寿命的影响.考虑到实际情况下模型所需材料附加强化系数有时难以获得的情况,给出了材料附加强化系数的有关近似计算公式.只需要材料基本力学参数便可得到材料附加强化系数,方便工程实际应用.采用8种材料的多轴疲劳寿命数据对提出的新模型进行检验,结果表明所提出的新模型与传统多轴疲劳模型相比预测寿命精度更高.     

拉扭复合加载下循环应力应变关系的研究

以拉扭簿壁管试件为研究对象,根据多轴临界面上的应力应变特性及多轴疲劳临界面法的结果,结合单轴循环应力应变关系,研究了多轴比例与非比例加载下的循环应力应变关系,推导出多应力应变关系模型,经拉扭复合比例与非比例物载试验难证,其预测结果与实测值相符合。     

Uniaxial and non-proportionally multiaxial ratcheting of SS304 stainless steel at room temperature: experiments and simulations

The uniaxial and non-proportionally multiaxial ratcheting behaviors of SS304 stainless steel at room temperature were initially researched by experiment and then were theoretically described by a cyclic constitutive model in the framework of unified visco-plasticity. The effects of cyclic stress amplitude, mean stress, and their histories on the ratcheting were experimentally investigated under uniaxial and different multiaxial loading paths. The shapes of non-proportional loading paths were linear, circular, elliptical and rhombic, respectively. In the constitutive model, the rate-dependent behavior of the material was reflected by a viscous term; the cyclic flow and cyclic hardening behaviors of the material under asymmetrical stress-controlled cycling were reflected by the evolution rules of kinematic hardening back stress and isotropic deforming resistance, respectively. The effect of loading history on the ratcheting was also considered by introducing two fading memorization functions for maximum inelastic strain amplitude and isotropic deformation resistance, respectively, into the constitutive model. The effect of multiaxial loading path on the ratcheting was reflected by a non-proportional factor defined in this work. The predicting ability of the developed model was proved to be good by comparing the simulations with corresponding experiments.     

An advancement in cyclic plasticity modeling for multiaxial ratcheting simulation

In a search for a constitutive model for ratcheting simulations, the models by Chaboche, Ohno–Wang, McDowell, Jiang–Sehitoglu, Voyiadjis–Basuroychowdhury and AbdelKarim–Ohno are evaluated against a set of uniaxial and biaxial ratcheting responses. With the assumption of invariant shape of the yield surface during plastic loading, the ratcheting simulations for uniaxial loading are primarily a function of the plastic modulus calculation, whereas the simulations for multiaxial loading are sensitive to the kinematic hardening rule of a model. This characteristic of the above mentioned models is elaborated in this paper. It is demonstrated that if all parameters of the kinematic hardening rule are determined from uniaxial responses only, these parameters primarily enable a better plastic modulus calculation. However, in this case the role of the kinematic hardening rule in representing the ratcheting responses for multiaxial loading is under-appreciated. This realization motivated many researchers to incorporate multiaxial load dependent terms or parameters into the kinematic hardening rule. This paper evaluates some of these modified rules and finds that none is general enough to simulate the ratcheting responses consistently for the experiments considered. A modified kinematic hardening rule is proposed using the idea of Delobelle and his co-workers in the framework of the Chaboche model. This new rule introduces only one multiaxial load dependent parameter to the Chaboche model, but performs the best in simulating all the ratcheting responses considered.     

Anatomy of coupled constitutive models for ratcheting simulation

This paper critically evaluates the performance of five constitutive models in predicting ratcheting responses of carbon steel for a broad set of uniaxial and biaxial loading histories. The models proposed by Prager, Armstrong and Frederick, Chaboche, Ohno-Wang and Guionnet are examined. Reasons for success and failure in simulating ratcheting by these models are elaborated. The bilinear Prager and the nonlinear Armstrong-Frederick models are found to be inadequate in simulating ratcheting responses. The Chaboche and Ohno-Wang models perform quite well in predicting uniaxial ratcheting responses; however, they consistently overpredict the biaxial ratcheting responses. The Guionnet model simulates one set of biaxial ratcheting responses very well, but fails to simulate uniaxial and other biaxial ratcheting responses. Similar to many earlier studies, this study also indicates a strong influence of the kinematic hardening rule or backstress direction on multiaxial ratcheting simulation. Incorporation of parameters dependent on multiaxial ratcheting responses, while dormant for uniaxial responses, into Chaboche-type kinematic hardening rules may be conducive to improve their multiaxial ratcheting simulations. The uncoupling of the kinematic hardening rule from the plastic modulus calculation is another potentially viable alternative. The best option to achieve a robust model for ratcheting simulations seems to be the incorporation of yield surface shape change (formative hardening) in the cyclic plasticity model.     

Uniaxial ratcheting of SS304 stainless steel at high temperatures: visco-plastic constitutive model

The uniaxial ratcheting of SS304 stainless steel at high temperatures (300, 600 and 700 °C) were analyzed experimentally, and described by a cyclic constitutive visco-plasticity model. The rate dependence of the material was accounted for by introducing a viscous term. The cyclic hardening and cyclic flow behavior of the material under asymmetrical stress-controlled cycling were described by the evolution rules of kinematic hardening back stress and isotropic deforming resistance. Under the isothermal condition, temperature effect was included by terms involving temperature in the evolution equations of isotropic deforming resistance. The effect of load history on ratcheting was also considered by introducing a fading memory function of the maximum inelastic strain amplitude and isotropic deformation resistance. After the material constants were determined from the experimental data, the uniaxial ratcheting of SS304 stainless steel was numerically simulated and compared with the corresponding experimental results at high temperatures. The predicted results agree well with the experimental ones.     

Uniaxial ratcheting and failure behaviors of two steels

The strain cyclic characteristics, ratcheting and failure behaviors of 25CDV4.11 steel and SS304 stainless steel were experimentally studied under uniaxial cyclic tests and at room temperature. The cyclic hardening/softening features of the materials were first observed under uniaxial strain cycling; and then the ratcheting and failure behaviors of the materials were researched in detail under cyclic stressing. The effects of stress amplitude and mean stress on the ratcheting and failure were discussed under uniaxial asymmetrical stress cycling. It is concluded that the ratcheting and failure behaviors of the materials depend greatly on the cyclic softening/hardening features of the materials and the stress values of cyclic loading. Some conclusions useful to understand the fatigue failure of the materials presented under asymmetrical cyclic stressing are obtained.     

304不锈钢室温单轴循环棘轮行为的粘塑性本构描述

在统一粘塑性循环本构模型的框架下对循环硬化的304不锈钢的单轴棘轮行为进行了本构描述. 模型中通过随动硬化背应力演化和各向同性变形阻力演化对304不锈钢在非对称应力循环下的循环附加硬化和循环流动特性进行了分析, 同时考虑了加载历史对循环棘轮行为的影响. 将模型应用于304不锈钢室温单轴循环棘轮行为及其对加载历史依赖性的描述中, 预言结果与实验结果吻合较好.