Oil recovery performances of surfactant solutions by capillary imbibition

Critical parameters playing a role in oil recovery by capillary imbibition of surfactant solutions were studied. Experiments conducted on sandstone and carbonate samples using different oil and surfactant types were evaluated for surfactant selection. In this evaluation interfacial tension (IFT), surfactant type, solubility characteristics of surfactants, rock type, initial water (pre-wet rock), and surfactant concentration were considered. In addition to these, a new technique was adopted to facilitate the surfactant screening process. This technique is based on assigning inorganic and organic property values and plotting organic conception diagrams (OCD) for surfactants. OCD defines the property of a compound in terms of physical chemistry in such a way that the property that depends much on the van der Waals force is called "organic" and the one that depends much on electric affinity is called "inorganic." Correlations between the capillary imbibition recovery performance and the properties of surfactant and oil (organic value (OV), inorganic value (IV), and IFT of surfactant solutions, oil viscosity, and surfactant type) were obtained. These correlations are expected to be useful in selecting the proper surfactant for improved oil recovery as well as identifying the effects of surfactant properties on the capillary imbibition performance.     

Tube radial distribution phenomenon observed in an aqueous micellar solution of non-ionic surfactant fed into a microspace and an attempt of capillary chromatographic application

A new type of tube radial distribution phenomenon was observed in an aqueous micellar solution of non-ionic surfactant that was fed into a microspace. A homogeneous aqueous solution containing 2 wt % Triton X-100 and 2.0 M sodium chloride was fed into a microchannel (40 μm in depth and 200 μm in width) in a microchip at a flow rate of 4.0 μL/min, where the microchip was maintained at a temperature of 34°C. The homogeneous aqueous solution changed to a heterogeneous solution with two phases in the microchannel; the surfactant-rich phase was generated around the middle of the channel, while the aqueous phase containing little surfactant was formed near the wall. The radial distribution of the surfactant was observed through Rhodamine B dissolved in the aqueous micellar solution with a bright-field microscope — CCD camera system. An open-tubular capillary chromatographic system was also tried to develop using the fusedsilica capillary tube (75 μm inner diameter and 120 cm length) as a separation column and the aqueous micellar solution as a carrier.     

Spontaneous rise of surfactant solutions into vertical hydrophobic capillaries

It has been found earlier (N.V. Churaev, G.A. Martynov, V.M. Starov, Z.M. Zorin, Colloid Polym. Sci. 259 (1981) 747) that aqueous surfactant solutions spontaneously rise in vertical hydrophobized quartz capillaries. A theory of this phenomenon is presented, which connects the experimental observations with the adsorption of surfactant molecules in front of the moving meniscus on the bare hydrophobic interface.     

Modulation of photo-oxidative DNA damage by cationic surfactant complexation

The natural packaging of DNA in the cell by histones provides a particular environment affecting its sensitivity to oxidative damage. In this work, we used the complexation of DNA by cationic surfactants to modulate the conformation, the dynamics, and the environment of the double helix. Photo-oxidative damage initiated by benzophenone as the photosensitizer on a plasmid DNA complexed by dodecyltrimethylammonium chloride (DTAC), tetradecyltrimethylammonium chloride (TTAC), cetyltrimethyammonium chloride (CTAC) and bromide (CTAB) was detected by agarose gel electrophoresis. By fluorescent titration in the presence of ethidium bromide (EB) and agarose gel electrophoresis, we experimentally confirmed the complexation diagrams with a critical aggregation concentration on DNA matrix (CAC DNA) delimiting two regions of complexation, according to the DNA-phosphate concentration. The study of the photo-oxidative damage shows, for the first time, a direct correlation between the DNA complexation by these surfactants and the efficiency of DNA cleavage, with a maximum corresponding to the CAC DNA for DTAC and CTAC, and to DNA neutralization for CTAC and CTAB. The localization of a photosensitizer having low water solubility, such as benzophenone, inside the hydrophobic domains formed by the surfactant aggregated on DNA, locally increases the photoinduced cleavage by the free radical oxygen species generated. The inefficiency of a water-soluble quencher of hydroxyl radicals, such as mannitol, confirmed this phenomenon. The detection of photo-oxidative damage constitutes a new tool for investigating DNA complexation by cationic surfactants. Moreover, highlighting the drastically increased sensitivity of a complexed DNA to photo-oxidative damage is of crucial importance for the biological use of surfactants as nonviral gene delivery systems.     

Co- and counter-current spontaneous imbibition into groups of capillary tubes with lateral connections permitting cross-flow

A model for co- and counter-current imbibition through independent capillaries has already been developed and experiments conducted to verify the theory [E. Unsal, G. Mason, N.R. Morrow, D.W. Ruth, J. Colloid Interface Sci. 306 (2007) 105]. In this paper, the work is extended to capillaries which are connected laterally and in which cross-flow can take place. The fundamental pore geometry is a rod in an angled round-bottomed slot with a gap between the rod and a capping glass plate. The surfaces of the slot, rod and plate form capillaries and interconnecting passages which have non-axisymmetric cross-sections. Depending on the gap size either (i) a large single meniscus, (ii) two menisci one on each side of the rod, or (iii) three menisci, one between the rod and the glass additional to the ones on each side can be formed. A viscous refined oil was applied to one end of the capillaries and co-current and counter-current spontaneous imbibition experiments were performed. The opposite end was left open to the atmosphere for co-current experiments. When the gap between the rod and the plate was large, the imbibing oil advanced into the tubes with the meniscus in the largest capillary always lagging behind the two menisci in the other two smaller capillaries. For counter-current imbibition experiments the open end was sealed and connected to a sensitive pressure transducer. In some experiments, the oil imbibed into the smaller capillaries and expelled air as a series of bubbles from the end of the largest capillary. In other experiments, the oil was allowed to imbibe part way into the tubes before counter-current imbibition was started. The meniscus curvatures of the capillaries have been calculated using the Mayer and Stowe-Princen method for different cell slot angles and gap sizes using a value of zero for the contact angle. These values have been compared with actual values by measuring the capillary rise in the tubes; agreement was very close. A model for co-current and counter-current imbibition has also been developed. The significance of this model is that some hydraulic/capillary properties are common for both co-current and counter-current imbibition. The experiments give an illustration of behavior expected in a real porous material and verify the importance of the 'perfect cross-flow' modification to the 'bundle of parallel tubes' model.     

Spontaneous vesicle formation in aqueous solution of zwitterionic and anionic surfactant mixture

Vesicles form spontaneously in the aqueous mixtures of dodecyl sulfonate betaine (DSB) and sodium bis(2-ethylhexyl) sulfosuccinate (Aerosol OT (AOT)) at certain mixing ratios, which has been demonstrated by microcalorimeter, negative-staining transmission electronic microscopy (TEM) and quasi-elastic light scattering (QELS) methods. The addition of NaCl will expand the range of vesicle formation, and monodispersed vesicles are obtained in the solution from the salinity of 0.03 to 0.09 M at the mixing molar ratio of 7/3 (DSB/AOT, mol/mol), with the polydispersity of the system lower than 0.1. To learn more about the structural change in the mixture, ultrasonic was employed finally. Meanwhile analysis was made from the viewpoint of molecular geometry structure.     

Dynamics of capillary imbibition when surfactant, polymer, and hot water are used as aqueous phase for oil recovery

Capillary imbibition is an oil recovery mechanism in naturally fractured reservoirs if rock matrix is water wet and there is enough water in fractures in contact with matrix. It, however, may not yield an effective recovery under certain circumstances even if these conditions are maintained. Heavy matrix oil, high interfacial tension (IFT), oil-wet matrix sample, and limited contact area of matrix with water in fractures require additional effort to enhance the oil recovery by capillary imbibition. Chemicals and heat can be injected into naturally fractured reservoirs to improve the capillary imbibition recovery performance. With the involvement of low IFT fluid, heat, and polymer solution in the process, capillary imbibition dynamics may change and this entails an identification of the dynamics of the process through laboratory experiments before injection of these expensive fluids into oil reservoirs. In this study, the dynamics of capillary imbibition was studied experimentally. Static imbibition experiments were conducted on oil- and water-wet rock samples under different boundary conditions and saturated with different types of oil. The analyses were conducted using three indicators, namely the capillary imbibition rate, ultimate oil recovery, and shape of the recovery profile. Based on these indicators, the dynamics of capillary imbibition of different aqueous phases were evaluated for different oil types and matrix properties. The conditions that cause weak or strong capillary imbibition were identified.     

Phase behavior of mixed solution of a glycerin-modified cationic surfactant and an anionic surfactant

The phase behavior of mixed solution of newly synthesized monoglycerylcetyldimethylammonium chloride (MGCA) and sodium octyl sulfate (SOS) in water was investigated by cryo-transmission electron microscopy (cryo-TEM), dynamic light scattering (DLS), differential scanning calorimetry (DSC), and fluorescence polarizing for evaluation of the microviscosity of bilayers. No precipitate was observed in the mixed solution except at concentrations below 20 mM over all mixing ratios, and stable vesicles were formed in a considerably wide range of mixing ratio, even at the equimolar ratio. Vesicles formed in aqueous 1/1 MGCA/SOS mixture were found to exhibit no phase transition, and fluorescence polarizing measurements showed that the vesicle bilayers have a high fluidity. This flexibility allows the bilayers to have a spontaneous curvature, and thus vesicles rather than flat lamellae can be stabilized in the mixture even at the equimolar ratio. In addition, because the glycerin group of MGCA interacts strongly with water, the hydration repulsion contributes to prevent the bilayers consisting of MGCA and SOS from adhering and flocculating even though the charge neutralization between MGCA and SOS occurs at the equimolar ratio.     

Wettability of a polytetrafluoroethylene surface by an aqueous solution of two nonionic surfactant mixtures

Measurements of the advancing contact angle (theta) were carried out for an aqueous solution of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol)s (Triton X-100 (TX100) and Triton X-165 (TX165) mixtures) on polytetrafluoroethylene (PTFE). The obtained results indicate that the wettability of PTFE depends on the concentration and composition of the surfactant mixture. The minimum of the dependence between the contact angle and composition of the mixtures for PTFE for each concentration at a monomer mole fraction of TX100, alpha = 0.8, points to synergism in the wettability of PTFE. This effect was confirmed by the negative values of interaction parameters calculated on the basis of the contact angle and by the Rosen approach. In contrast to Zisman, there was no linear dependence between cos theta and the surface tension of an aqueous solution of TX100 and TX165 mixtures for all studied systems, but a linear dependence existed between the adhesional tension and surface tension for PTFE over the whole concentration range, the slope of which was -1, indicating that the surface excess of the surfactant concentration at the PTFE-solution interface was the same as that at the solution-air interface for a given bulk concentration. Similar values of monomer mole fractions of the surfactants at water-air and PTFE-water interfaces calculated on the basis of the surface tension and contact angles showed that adsorption at these two interfaces was the same. It was also found that the work of adhesion of an aqueous solution of surfactants to the PTFE surface did not depend on the type of surfactant and its concentration. This means that for the studied systems the interaction across the PTFE-solution interface was constant and was largely of Lifshitz-van der Waals type. On the basis of the surface tension of PTFE, the Young equation, and the thermodynamic analysis of the adhesion work of an aqueous solution of surfactant to the polymer surface, it was found that in the case of PTFE the changes in the contact angle as a function of the mixture concentration of two nonionic surfactants resulted only from changes in the polar component of the solution surface tension.     

Capillary imbibition of surfactant solutions in porous media and thin capillaries: partial wetting case

The capillary imbibition of aqueous surfactant solutions into dry porous substrates is investigated from both theoretical and experimental points of view in the case of partial wetting. Cylindrical capillaries are used as a model of porous media to study the problem. It is shown that if the mean pore size is below a critical value, then the permeability of the porous medium is not influenced by the presence of surfactants whatever the value of the concentration: the imbibition front moves exactly in the same way as in the case of the imbibition of pure water. The critical radius is determined by the adsorption of the surfactant molecules onto the inner surface of the pores. If the mean pore size is larger than the critical value, then the permeability increases with increasing surfactant concentration. These theoretical conclusions are in agreement with the experimental observations.     

Enantioseparation of derivatized amino acids by capillary isoelectric focusing using cyclodextrin complexation

Enantioseparation of dansylated as well as 6-aminoquinolyl-N-hydroxysuccinimidylcarbamate (AQC)-derivatized amino acids by means of capillary isoelectric focusing using various cyclodextrin derivatives is demonstrated. Separation is based on the enantioselective shift of the isoelectric points upon complexation with the chiral selectors. The zwitterionic, diastereomeric analyte-cyclodextrin complexes exhibited differences in the pI values up to more than 0.25 pI units. Enantioresolution was achieved for a number of derivatized amino acids and various selectors added to the carrier ampholyte solution. The hydroxypropyl-beta-cyclodextrin proved to be the best selector for this purpose. Enantioseparation as dependent on the selector concentration was evaluated in a range between 5 and 30 mM. Separation could be attained down to selector concentrations corresponding to a degree of complexation as low as 30%. The peaks appear according to the degree of complexation between the positions adopted without and with full complexation. The kinetics of complex formation and dissociation was fast enough in most instances to produce single peaks, even with complexation degrees near 0.5 and significant pI shifts. Peak widths were slightly enlarged in these instances. The method offers excellent perspectives for preparative applications.     

Characterization and determination of poly(vinylpyrrolidone) by complexation with an anionic azo-dye and nonequilibrium capillary electrophoresis

Using capillary zone electrophoresis in nonequilibrium conditions, the complexes of poly(vinylpyrrolidone) (PVP) with anionic azo-dyes dissociate following a first-order kinetics. Two peaks due to the remaining PVP–dye complexes and the equilibrium concentration of the free dye, plus an exponential region due to the dye liberated by the complexes during the electrophoretic run, are obtained. This behaviour was closely similar to that described in the literature for protein–probe and DNA–protein mixtures, upon application of the technique known as nonequilibrium capillary electrophoresis of equilibrium mixtures or NECEEM. Using Congo Red and Acid Blue 113, information about the maximal stoichiometry and average stability of the PVP–dye complexes was obtained. The procedure was also useful to predict the average molecular mass of PVP and to determine PVP in cleaning products and pharmaceutical preparations. By using an appropriate probe, the procedure should be also useful to characterize and determine many other synthetic or natural nonionic polymers, and to study polymer–probe interactions.     

Controlled complexation of plasmid DNA with cationic polymers: effect of surfactant on the complexation and stability of the complexes

The aggregation of the cationic polymer-plasmid DNA complexes of two commonly used polymers, polyethyleneimine (PEI) and poly-l-lysine (PLL) were systematically compared. The complexation was studied in 5% glucose solution at 25 degrees C using dynamic light scattering and isothermal titration calorimetry. The aggregation of the complexes was controlled by addition of the surfactant polyoxyethylene stearate (POES). The stability of the complexes was evaluated using dextran sulphate (DS) as relaxing agent. The relaxation of the complexes in the presence of DS was studied using agarose gel electrophoresis. This study elucidates the role of surfactant in controlling the size of the PEI/pDNA complex and reveals the differences of the two polymers as complexing agents.     

Determination of metal ions by capillary electrophoresis using pre-column complexation with 1,10-phenanthroline

The capillary electrophoretic separation of Fe(II), Cu(II) and Zn(II) ions in an acidic buffer solution (pH 2.5) by complexation with 1,10-phenanthroline is investigated. As 1,10-phenanthroline is a neutral ligand, the positively charged metal complexes formed migrate in the same direction as the EOF, providing a rapid separation of metal ions in acidic buffers. The method was applied to the determination of metal ions in vitamin tablets. Received: 5 January 1998 / Revised: 27 March 1998 / Accepted: 15 May 1998     

Selective foam separation of binary protein solution by SDS complexation method

A fundamental study about the selective foam separation of protein mixture was carried out. A solution containing two proteins, ovalbumin (OA) and lysozyme (LZ), and an anionic surfactant, sodium dodecyl sulfate (SDS), was adjusted to pH 6.0, which referred to an intermediate state between the isoelectric points of the proteins. The solution was processed by continuous foam separation. The results showed that a proper addition of SDS greatly improved the selective recovery of LZ to OA. The experimental data were well explained by a simple model that most of cationic protein molecules (LZ) are associated with SDS and the adsorption of all the species including LZ-SDS complexes are subjected to Langmuir adsorption isotherm. The results also showed that one of the Langmuir parameters, which means a kind of lyophillic property of adsorbed material, of LZ-SDS complexes was extremely large as compared with that of primary protein.     

Determination of metal ions by capillary electrophoresis using pre-column complexation with 1,10-phenanthroline

The capillary electrophoretic separation of Fe(II), Cu(II) and Zn(II) ions in an acidic buffer solution (pH 2.5) by complexation with 1,10-phenanthroline is investigated. As 1,10-phenanthroline is a neutral ligand, the positively charged metal complexes formed migrate in the same direction as the EOF, providing a rapid separation of metal ions in acidic buffers. The method was applied to the determination of metal ions in vitamin tablets. Received: 5 January 1998 / Revised: 27 March 1998 / Accepted: 15 May 1998     

Structure selective complexation of cyclodextrins with five polyphenols investigated by capillary electrokinetic chromatography

The complexation of five polyphenols, namely trans‐resveratrol, astilbin, taxifolin, ferulic acid, and syringic acid (guest molecules) with α‐, β‐, and γ‐cyclodextrin (host molecules), was investigated by capillary electrokinetic chromatography. The binding constants were calculated based on the effective electrophoretic mobility change of guests with the addition of cyclodextrins into the background electrolyte. Because of cavity size, cyclodextrins showed structure‐selective complexation property to different guest. The stability of the trans‐resveratrol complexes was in the order of β‐ > α‐ > γ‐cyclodextrin. The cavity size of α‐cyclodextrin was too small for astilbin and taxifolin molecules, and thus they could not form complexes. The molecular size of syringic acid was too big for all cyclodextrins cavity, and no cyclodextrin could form complexes with it. Temperature studies showed that the binding constants decreased with the rise of temperature. Enthalpy and entropy values were calculated and the negative values of these parameters indicated that the complexation process was enthalpy‐controlled. Van der Waals force and release of high‐enthalpy water molecules from the cyclodextrins cavity played important roles in the process.