实际大气中闪烁指数测量的数据处理

在闪烁指数定义的基础上,综合考虑背景光噪声、探测器固有噪声和散粒噪声等影响闪烁指数测量精确度的因素,修改了测量系统的数学模型,并对现有数据处理方法做出改进。在1 km距离上进行了激光水平传输实验,分别采用了现有方法和改进方法处理实验数据,并对获取的3种闪烁指数进行了比较。实验结果显示:修改后数学模型相比现有模型更符合实测值;相比系统本底噪声,探测器散粒噪声要高出一个数量级,将会严重影响测量准确度;在信噪比有较大波动的条件下,改进方法受到的影响小于现有方法;在信噪比较低时,改进方法的准确度优于现有方法。     

Alternative method of wavelength drift free dual-wavelength heterodyne interferometry for the absolute distance measurement

Based on the technique of dual-wavelength and principle of heterodyne interferometry, a modified method for measuring the absolute distance is proposed. Because two test lights suffer from the same influence of wavelength drift in the measurement setup, the minus effect coming from the wavelength drift can be offset. Therefore, the measurement accuracy can be significantly increased. The feasibility of this method was demonstrated with a measurement resolution of about 1.50 μm. This method provides the advantages of a simple optical setup, easy operation and rapid measurement.     

Increasing the efficiency of post-selection in direct measurement of the quantum wave function

Direct weak or strong measurement of quantum wave function based on post-selections has been widely explored; however, the efficiency of the measurement is heavily limited by the success probability of post-selection. Here we propose a modified scheme to directly measure photon's wave function by simply inserting a liquid crystal plate before the post-selection stage. Numerical simulations demonstrate that our modified method can significantly increase the efficiency of post selection. Our proposal would speed up the quantum wave function measurement with high resolution and high fidelity.     

A modified electro-acoustical reciprocity method for measuring low-frequency sound source in arbitrary surroundings

The reciprocity principle provides a possible means of measuring the low-frequency volume velocity of a sound source in arbitrary surroundings; however, the auxiliary transducer in the reciprocity experiment is required to be absolutely reciprocal, which means that the radiation property and the receiving property of the transducer are identical. However, it is not always easy to obtain such a low-frequency reciprocal transducer, because some issues like nonlinearity would lead the transducer to be non-reciprocal. In this study, a modified method is proposed to conduct the reciprocity measurement using an ordinary loudspeaker instead of a strictly reciprocal one as the auxiliary transducer. Firstly, the relationship is established between the measurement error and the inconsistency of auxiliary loudspeaker’s radiation property and receiving property. Furthermore, a modified reciprocity method is proposed to compensate the inconsistency. Finally, experiments are carried out with the modified reciprocity method in both an anechoic room and a reverberation room with two different auxiliary loudspeakers. The experimental results of the modified reciprocity method agree with the results obtained with the free field method very well.     

基于改进哈特曼法的眼镜片全孔径屈光度测量

自由曲面镜片的发展和普及,对现有的屈光度测量方法提出了挑战,也要求新的测量方法具有更高的精度以及更好的可靠性。因此,介绍了传统哈特曼检测法测量眼镜片屈光度的测量原理并提出了一种改进方法,对球面单焦点镜片和散光镜片进行仿真测量的屈光度误差均在1%以内。对改进方法与传统方法测量所得到的渐进多焦点自由曲面镜片屈光度分布图的分析结果表明,改进哈特曼检测法相比于传统哈特曼检测法具有测量范围大,精度高的特点,能够准确反映眼镜片的屈光度分布特征。     

缺陷关联参数红外检测Levenberg-Marquardt改进识别算法研究

对Levenberg-Marquardt(LM)算法在缺陷参数估计修正过程中无法确保参数几何关联性的局限性进行改进,并保留原算法快速收敛的特性.以二维试件内部矩形缺陷红外检测为例,采用数值实验方法比较改进前后的LM算法,分析初始假设、红外测温误差对缺陷定量识别结果的影响.数值实验表明:改进后的LM算法参数修正过程中确保了关联性的一致性;不同初始假设对缺陷识别结果的影响不大;受红外测温误差的影响,各缺陷参数之间表现出不同的识别精度.     

Absolute distance measurement by using modified dual-wavelength heterodyne Michelson interferometer

This study proposes a modified dual-wavelength heterodyne Michelson interferometer for measuring the absolute distance that can avoid the influence of wavelength drifts. This modified interferometer consists of two conventional Michelson interferometers. A standard plate is introduced in one arm of one Michelson interferometer. The phase differences of p- and s- polarization test lights in the two interferometers can be measured accurately by dual-wavelength heterodyne interferometry. Hence, the absolute distance can be determined by substituting the phase differences into special derived equations. Meanwhile, the test lights suffer from the same wavelength drift effect. Therefore, the negative effect caused by the drift can be offset, and the measurement stability can be significantly increased. The feasibility of this method was demonstrated with a measurement resolution of about 1.36 μm. Additionally, this method has a simple structure, easy operation and rapid measurement.     

Error compensation in two-step triangular-pattern phase-shifting profilometry

This paper presents an analysis of error compensation using a newly modified two-step triangular-pattern phase-shifting measurement method, developed to reduce periodic measurement errors due to gamma nonlinearity and defocus of the projector and camera. Experimental analysis revealed that a trade-off is necessary in choosing a higher minimum projector input intensity to use the more linear region of input-to-output intensity mapping, and a lower minimum input intensity for greater dynamic range of input intensity. The modified two-step triangular-pattern phase-shifting method performs two-step triangular-pattern phase-shifting twice, the second time with an initial phase offset of one-eighth of the pitch, and generates the three-dimensional object height distribution by averaging the two obtained object-height distributions. The modified two-step triangular-pattern phase-shifting method consistently had higher measurement accuracy than the unmodified method. Errors were reduced by 23.4% at the midrange of depth using an input intensity value of 40, which yielded the highest measurement accuracy and up to 64% and 54% at small and large depths, respectively.     

Improved method for depth profiling of multilayer structures

A modified, improved method has been developed for the dissolution of semiconductor materials containing a GaAlAs layer. This modified method involves the alternate application of anodic and cathodic processes in order to produce an arsenic-free surface for the carrier concentration measurement.

The advantageous features of this method are demonstrated by comparison of the depth profiles of various semiconductor structures obtained by conventional and modified techniques.     

Optimal design of acoustic performance for automotive air-cleaner

The research on optimal design of acoustic performance for air-cleaner was presented and evaluated in this paper using a numerical simulation method and experimental method. A modified measurement was proposed in the paper to solve the problem of air flow noise caused by the original measurement layout. The modified measurement was proved to produce good results. A new study on the acoustic effect of filter was also developed here and noise reduction (NR) of the air-cleaner was predicted based on the study using the numerical simulation method. Actual intake noise was then predicted using the simulation method. Side branch silencers were designed to improve the acoustic capacity of the air-cleaner. The result shows that the newly optimized air-cleaner has a much better performance of noise elimination when engine operating.     

Experimental investigation of a modified Beckmann-Kirchhoff scattering theory for the in-process optical measurement of surface quality

An experimental investigation of a modified Beckmann-Kirchhoff scattering theory applied in an in-process optical measurement of surface quality is described. The proposed theory describes the scattered light intensity distribution from a surface with the additional layers, and can be employed to analyze the surface characteristics in in-process measurement. Based on light scattering principle and machine vision method, the surface roughness is extracted to testify the correction of the modified Beckmann-Kirchhoff scattering theory. The experimental apparatus consists of a collimated laser diode, a beam splitter, a screen, a measuring lens and a camera. Test specimens with different surface roughness are studied. The results obtained demonstrate the feasibility of in-process optical measurement of surface quality using the modified model.     

Research on three-dimensional shape reconstruction of circular cylindrical flaw

In this article, three-dimensional Born inverse scattering method is modified to convenient form for a cylindrical specimen that includes three-dimensional defect. One aluminum cylinder with flaw model is prepared and ultrasonic measurements are carried out. The measurement area in the modified methods is restricted in the plane perpendicular to the axis of cylindrical specimen. That’s to say that the method is modified to convenient form to use measured waveforms in the x₁ − x₂ plane. The measured wave data are fed into the inversion method and cross-sectional images are obtained. Then, three-dimensional shape reconstruction of flaw model in aluminum specimen is performed by piling up the cross-sectional images. At the same time, we get the numerical results from all directions by finite element method.     

Measurement of structural intensity using boundary element method-based nearfield acoustical holography

The regularization method for measurement of structural intensity (SI) using boundary element method (BEM)-based nearfield acoustical holography (NAH) is proposed. Spatial derivatives of normal displacement are necessary to obtain the structural intensity. The derivative operations amplify high-wavenumber component of measurement noise and contaminate the measurement result of SI. To overcome this difficulty, regularization method for measurement of SI using fast Fourier transform-based NAH has been introduced. In this paper, this regularization method is modified for the BEM-based NAH. The BEM-based NAH avoids the aperture replication problem; therefore, measurement aperture for BEM-based NAH can be set smaller than that for FFT-based NAH. The effectiveness of the proposed method is demonstrated by experiments.     

基于改进倾斜刃边法的光电成像系统MTF高准确度测试

提出一种能高准确度测试光电成像系统调制传递函数的改进的倾斜刃边法.利用一种自动确定高低阈值的改进Canny算子提取边缘位置点,对提取到的边缘位置点进行线性拟合求得刃边倾角,在利用费米函数拟合边缘扩散函数的过程中,提出一种邻域平均值和设定误差容限的多重去噪改进方法.通过仿真与物理实验证明了本文方法的有效性,并分析了刃边倾角、噪声变化对本文方法与传统方法MTF测试准确度的影响.实验结果表明:本文方法的调制传递函数测试准确度达到0.004 9,重复准确度达到0.003 1,皆优于传统方法;说明其具有较高的测试准确度和良好的测试重复性,并且具有较强的抗噪性,基本不受刃边倾角变化的影响.     

Measurements of phase retardation and principal axis angle using an electro-optic modulated Mach–Zehnder interferometer

This paper presents an electro-optic modulated circular heterodyne modified Mach–Zehnder interferometer and a convenient two-phase signal-processing algorithm for the measurement of variations in the magnitude of phase retardation and the angle of principal axis in optical materials. The developed method solves the problems of normalized intensity jump and limited phase retardation measurement range associated with the circular heterodyne interferometer proposed previously. The present method uses a saw-tooth wave signal to drive an electro-optic (EO) modulator, and employs a lock-in amplifier to demodulate the principal axis angle and the phase retardation. Specifically, this paper considers two main sources of measurement errors, namely the misorientation of the EO modulator and the reflection phase retardation of the beam splitter. Furthermore, the study develops calibration procedures and identifies a means to minimize measurement errors induced by the reflection phase retardation of the beam splitter.     

HELS法在循环平稳声场全息重建中的理论与实验研究

Helmholtz 方程最小二乘法利用一组球面波基函数拟合声源产生的声场,根据重建和实际声压的误差最小原则,利用最小二乘法确定基函数展开的项数以及对应的权重系数,该方法具有计算效率高和需要测点少的优点,在实际工程中有很大的实用性.Helmholtz 方程最小二乘法和其他近场声全息方法一样都是针对平稳声场,对非平稳声场的分析很少.对于实际工程中经常遇到的一类特殊非平稳声场——循环平稳声场,现有的技术多以单通道信号分析为主,其高阶统计量在故障诊断领域应用较广.分析了循环平稳声场中Helmholtz方程最小二乘 关键词： 声全息 循环平稳 Helmholtz 方程 球面波     

Measurement of polarization mode dispersion in single mode fibre

Polarization mode dispersion (PMD) in fibre seriously limits the high-capacity optical fibre communication system. The measurement of PMD was realized by three methods — wavelength scanning method, modified OTDR method and modified York S-38 dispersion meter method. Different types of fibres have been measured using the above three methods and the results have been found to be consistent. Finally, we also found that the measured results of longer non-polarization-maintaining fibre satisfied the Maxwellian probability density function and the results of polarization maintaining fibre were derived. Supported by The National Natural Science Foundations of P. R. China.     

改进粒子群算法的立体传声器阵列声成像系统阵形优化设计

提出改进的粒子群优化算法,获得波束方向图主瓣宽度和旁瓣级折中的优化立体阵形,避免基本实数粒子群算法仅采用旁瓣级或主瓣宽度一个性能指标优化而导致另一个性能指标恶化的问题,利用阵列视角限制进一步优化立体阵形并设计了声成像测量系统。改进的粒子群算法与基本粒子群算法仿真优化阵形比较表明改进粒子群算法设计的优化阵形在保持较窄的主瓣宽度的条件下具有较低的旁瓣级。阵列声成像测量系统的性能测量分析结果表明该系统的空间分辨率和旁瓣抑制能力与理论结果接近,验证了所提算法的有效性。      

菲索干涉仪中精确移相的实现

为了实现移相式菲索干涉仪对光学元件面形的高精度测量,建立了干涉仪同步采集移相系统,并对精确移相方法进行了研究。介绍了移相系统的构成和工作原理,计算了测量过程中移相器的速度。针对PZT移相器在移相过程中会引入离焦误差,并存在加速段和减速段的问题,详细设计了移相器的行进过程。最后,对移相器的性能进行了标定。在改造后的干涉仪上开展了重复性验证实验,结果表明：干涉仪可以获得λ/11 340的RMS测量重复性。对改造后干涉仪与Zygo公司生产的Verifire XP/D干涉仪的测量精度做了比对实验,结果显示：相同元件下两者测量结果的面形RMS之差约为0.9 nm,表明提出的移相系统及移相方法在重复性和准确度方面都能满足纳米级面形测量的要求,为研制高精度移相干涉仪奠定了基础。     

聚焦法测量梯度折射率透镜的折射率分布

本文针对梯度折射率分布的透镜(以后简称梯析透镜)与光纤在折射率分布上的不同点,对用于光纤及其预制棒测量的聚焦法的原理公式,计算测量方法等进行了重要改进,从而使聚焦法可适用于梯折透镜的测量.本文通过计算机模拟计算,对原理公式及计算方法的准确性和可靠性进行了验证,并同时给出了这一测量方法的精度,最后给出了测量实例及其比较结果.