ICP-MS multielemental determination of metals potentially released from dental implants and articular prostheses in human biological fluids

A sector field high-resolution (HR)-ICP-MS and an octapole reaction system (ORS)-ICP-MS have been compared for the simultaneous determination of traces of metals (Ti, V, Cr, Co, Ni, and Mo) released from dental implants and articular prostheses in human biological fluids. Optimum sample treatments were evaluated to minimize matrix effects in urine and whole blood. Urine samples were diluted tenfold with ultrapure water, whereas whole blood samples were digested with high-purity nitric acid and hydrogen peroxide and finally diluted tenfold with ultrapure water. In both matrices, internal standardization (Ga and Y) was employed to avoid potential matrix interferences and ICP-MS signal drift. Spectral interferences arising from the plasma gases or the major components of urine and whole blood were identified by (HR)-ICP-MS at 3,000 resolving power. The capabilities of (HR)-ICP-MS and (ORS)-ICP-MS for the removal of such spectral interferences were evaluated and compared. Results indicate that polyatomic interferences, which hamper the determination of such metallic elements in these biological samples, could be overcome by using a resolving power of 3,000. Using (ORS)-ICP-MS, all those elements could be quantified except Ti and V (due to the polyatomic ions ³¹P¹⁶O and ³⁵Cl¹⁶O, respectively). The accuracy of the proposed methodologies by (HR)- and (ORS)-ICP-MS was checked against two reference materials. Good agreement between the given values and the concentrations obtained for all the analytes under scrutiny was found except for Ti and V when analyzed by (ORS)-ICP-MS.     

Capillary electrophoresis with contactless conductivity detection for uric acid determination in biological fluids

The suitability of capillary electrophoresis (CE) with capacitively coupled contactless conductivity detection (C⁴D) for the direct determination of uric acid in human plasma and urine was investigated. It was found that a careful optimization of the buffer composition and pH was necessary to achieve selective determination in the complex sample matrices. An electrolyte solution consisting of 10 mM 2-morpholinoethanesulfonic acid (MES), 10 mM histidine and 0.1 mM hexadecyltrimethylammonium bromide (CTAB), pH 6.0, was finally found suitable for use as running buffer for both sample matrices. The limit of detection (3 S/N) was determined as 3.3 μM. The linearity of the response was tested for the range between 10 and 500 μM and a correlation coefficient of 0.9996 was obtained. Intra- and inter-day variabilities were <10%. Quantitative analysis of urine and plasma samples showed a good correlation with the routine enzymatic method currently used at the University Hospital of Basel.     

电感耦合等离子体质谱法测定汽车尾气净化催化剂中铂、钯、铑含量

汽车尾气净化催化剂样品经过氧化钠熔融,用热水浸出,加入盐酸酸化后,分取部分试液用电感耦合等离子体质谱法测定其中铂、钯、铑的含量。选择镉(~(111)Cd)和铊(~(203)Tl)作为内标元素。铂、钯、铑的检出限(3s)分别为0.048,0.056,0.019μg·g~(-1)。方法用于5件催化剂样品的分析,测定结果与光度法测定结果相一致。铂、钯、铑的平均回收率分别为100.0%,100.0%,99.8%;相对标准偏差(n=12)分别为1.3%,1.0%,1.6%。     

Iodine determination in biological materials by ICP-MS

The present work describes an analytical procedure for the determination of the total iodine content in biological materials (serum, milk, plants, tissues etc.). Liquid samples can be directly analyzed after dilution, if necessary, by ICP-MS. Milk powder, plants and tissues were dissolved by using a modified simple Schöninger combustion, subsequently the residue was taken up in 0.1 mol/l NaOH and this solution was analyzed by ICP-MS. The detection limit is in the range of 0.01 g/l. The method was tested using different CRMs certified for the iodine content.     

Investigation of ICP-MS spectral interferences in the determination of Rh, Pd and Pt in road dust: Assessment of correction algorithms via uncertainty budget analysis and interference alleviation by preliminary acid leaching

A method for classification of the potential spectral interferences in inductively coupled plasma mass spectrometry (ICP-MS) was proposed based on statistical assessment of the interfering signals. The concept was applied to investigate the variety of spectral interferences over the isotopes of Rh, Pd and Pt concerning their analysis in road dust samples. For the significant interferences the applicability of mathematical corrections using two alternative algorithms were studied by uncertainty budget analysis and the approach resulting in lower combined uncertainty of the corrected signals was selected. Further the uncertainty evaluation was used for assessment of the most appropriate Pd isotope to be measured. The adequateness of the mathematical corrections for Rh and Pd was highly relevant to the number of elements causing spectral interferences and the relative analyte/interferent concentrations. This was overcome by preliminary road dust leaching with 0.35 mol l⁻¹ hydrochloric acid. Interferents present as easily soluble salts were substantially removed form the samples while the platinum group metals were not leached which allowed a relative analyte preconcentration to be obtained. For the leached samples the isotopes of Rh and Pd were still spectrally interfered from Sr, Y and Pb but at considerably lesser degree thus after mathematical correction the ICP-MS analysis of Rh, Pd and Pt was reliable and robust using the isotopes 103, 105 and 195, respectively. The method was validated via an alternative analysis based on selective separation of the platinum group metals by microwave-assisted cloud point extraction.     

Microwave-assisted solid phase extraction prior to ICP-MS determination of Pd and Pt in environmental and biological samples

A sensitive and selective microwave-assisted solid phase extraction procedure coupled to inductively coupled plasma-mass spectrometry (ICP-MS) is proposed for palladium (Pd) and platinum (Pt) quantification in environmental and biological samples. Pd and Pt were quantitatively retained on commercial thioureido propyl functionalised silica gel packed inside a home-made glass microcolumn, and later eluted with 0.5% thiourea solution under microwave irradiation, followed by ICP-MS determination. The main variables affecting the procedural stages (i.e., sorption and desorption) and ICP-MS determination were optimised. The best conditions found were: (a) sorption: sample acidity, 1?M HCl; sample flow rate, 3?mL?min^?1; (b) desorption: microwave radiation, power 800?W; eluent concentration, 0.5% thiourea; eluent flow rate, 0.5?mL?min^?1; (c) ICP-MS determination: nebuliser feeding, free aspiration (0.3?mL?min^?1); internal standard, Rh (5?µg?L^?1). Analyte recoveries were higher than 90% and concentration factors up to 90 and 92 were achieved for Pd and Pt, respectively. Depending on the conditions, the methodological limits of detection were down to 0.2?ng?L^?1 for both analytes and repeatability, expressed as RSD%, varied between 1.3 and 11.0%. A method selectivity evaluation showed that most of the ICP-MS interferents were either quantitatively separated or more than 86% eliminated, except for Cu (elimination efficiency around 30%). Finally, the method was successfully used to determine Pd in certified reference materials (i.e. human urine and serum) and Pd and Pt in PM₁₀ airborne particulate matter fractions.     

ICP-MS法测定高纯铝中杂质不确定度的评定

利用ICP-MS测定高纯铝中杂质。用建立数学模型的方法对结果的不确定度进行评估和计算。对试料的称重、标准溶液的配制、工作曲线的拟合、测量重复性的各分量不确定度进行分析。得到了各分量不确定度和合成不确定度,最终得出更加客观的结果。     

Development of a validated HPLC method for the determination of four penicillin antibiotics in pharmaceuticals and human biological fluids

A quantitative method for the determination of four penicillin antibiotics, amoxicillin (AMO), oxacillin (OXA), cloxacillin (CLO), and dicloxacillin (DICLO), has been developed. Separation was achieved on an Inertsil ODS-3 (250 x 4 mm, 5 microm) column after selective extraction of penicillin drugs from biological matrices by means of SPE. Gradient elution with a mobile phase consisting of 0.1% TFA (pH 1) and ACN, and PDA detection with monitoring at 240 nm was applied. Salicylic acid (5 ng/microL) was used as the internal standard. RP-8 Adsorbex Merck cartridges provided high absolute recoveries (98-101%). The developed method was fully validated in terms of selectivity, linearity, accuracy, precision, stability, and sensitivity. Repeatability (n = 8) and between-day precision (n = 8) revealed RSD <10%. Recoveries from biological samples ranged from 91 to 103%. The detection limits were estimated as 3.3 ng for AMO, OXA, and CLO, and 6.6 for DICLO in blood plasma. LOD in whole blood and urine was 6.6 ng. Injection volume was 20 microL. The method was applied to commercially available AMO containing pharmaceuticals and spiked biological matrices. The method was also applied to biological samples after AMO oral administration, where the drug was successfully identified and quantified.     

On‐line determination of sarcosine in biological fluids utilizing dummy molecularly imprinted polymers in microextraction by packed sorbent

Several years ago, sarcosine received attention as a prostate‐cancer marker. Prostate cancer is one of the most widespread types of tumor diseases in men. The prostate‐specific antigen is normally used as a marker, and it can only be detected in blood with a sensitivity of approximately 80%. In the present study, dummy molecularly imprinted polymers in microextraction by packed sorbent with on‐line liquid chromatography coupled to tandem mass spectrometry was used for the determination of sarcosine in human plasma and urine samples. The polymer network glycine was used for the dummy molecularly imprinted polymers. The selectivity of the method was evaluated using similar prostate‐cancer biomarkers. In addition, various parameters affecting the extraction performance were investigated. The method limits of detection and quantification in the plasma and urine were 1.0 and 3.0 ng/mL, respectively. The values of the coefficient of determination were over 0.99 for all runs in the studied concentration range (3.0–10 000 ng/mL). The method recovery was 87 and 89% in plasma and urine, respectively. The intraday and interday precisions of sarcosine in the plasma and urine samples were in the ranges of 4.0–7.1, 3.0–6.3, 2.9–4.7, and 5.0–6.7, respectively.     

An uncertainty budget for trace analysis by isotope-dilution ICP-MS with proper consideration of correlation

Isotope-dilution mass spectrometry (IDMS) is considered to be a method without significant correction factors. It is also believed that this method is well understood. But unfortunately a large number of different uncertainty budgets have been published that consider different correction factors. These differences lead to conflicting combined uncertainties especially in trace analysis. It is described how the known correction factors must be considered in the uncertainty budget of values determined by IDMS combined with ICP-MS (ICP-IDMS). The corrections applied are dead time, background, interference, mass discrimination, blank correction and air buoyancy.IDMS measurements consist always of a series of isotope abundance ratio measurements and can be done according to different measurement protocols. Because the measurement protocols of IDMS are often rather sophisticated, correlations of influence quantities are difficult to identify. Therefore the measurement protocol has to be carefully considered in the specification of the measurand and a strategy is presented to properly account for these correlations. This will be exemplified for the estimation of mass fractions of platinum group elements (PGEs) and Re in the geological reference material UB-N (from CRPG-CNRS, Nancy in France) with ICP-IDMS. The PGEs with more than one isotope and the element Re are measured with on-line cation-exchange chromatography coupled to a quadrupole ICP-MS. All contents are below 10 µg kg^–1. Only osmium is separated from the matrix by direct sparging of OsO₄ into the plasma. This leads to transient signals for all PGEs and Re. It is possible to estimate the combined uncertainties and keep them favourably small despite the low contents, the transient signals and the sophisticated correction model.     

ICP-MS技术快速测量尿样中的铀同位素

核事故状态下的应急处理要求对环境介质中的放射性核素进行快速分析。尿样中铀同位素测量作为内照射剂量评价的主要手段,其分析效率越高,则对核事故中涉铀人员的安全救治越及时、有效。尿样中其他无机离子的含量是铀含量的106倍,导致ICP-MS测量过程中尿盐堵塞进样毛细管。为降低样品的含盐量并获得较好的检测结果,本文对样品预处理过程进行优化。采用先加热氧化去除有机物,再进行1~10倍稀释后测试样品的铀同位素丰度及浓度。结果表明,将25m L样品稀释至100m L后效果最佳,分析方法相对标准不确定度为5.4%,回收率95%~105%。     

Terbium-sensitized luminescence optosensor for the determination of norfloxacin in biological fluids

The use of a flow through solid phase terbium-sensitized luminescence system is described for the determination of the widely used fluoroquinolone norfloxacin. A chelate between the terbium ion and the analyte is formed online previously to the sample injection into the carrier stream. Then the chelate is transported towards the flow-through cell, where it is retained on a cationic Sephadex resin packed in the cell, developing the corresponding luminescence signal. Afterwards, an ethylenediaminetetraacetic acid solution was used as eluting agent, in order to regenerate the sensing zone. The system has been satisfactorily applied to the determination of norfloxacin in human urine and serum, without the need of a pre-treatment. The response was linear in the range 10-150 ng ml⁻¹. The detection and quantification limits were 1.5 and 5 ng ml⁻¹, respectively and the R.S.D. 1.82%.     

Development of a validated HPLC method for the determination of four 1,4-benzodiazepines in human biological fluids

A simple and sensitive HPLC method was developed and validated for the determination of four frequently prescribed 1,4-benzodiazepines: alprazolam (ALP), bromazepam (BRZ), diazepam (DZP), and flunitrazepam (FNZ). Separation was achieved on an Inertsil C8 analytical (250 mm x 4 mm, 5 microm) column, after selective extraction of benzodiazepine drugs from biological matrices by means of SPE. Isocratic elution was performed with a mobile phase consisting of CH3COONH4, 0.05 M CH3OH, and CH3CN (33:57:10 by volume). Quantification was performed at 240 nm with mefenamic acid (6 ng/microL) as the internal standard. DSC-18 Supelco cartridges provided high absolute recoveries (81-115%). The developed method was fully validated in terms of selectivity, linearity, accuracy, precision, stability, and sensitivity. Repeatability (n = 8) and between-day precision (n = 8) revealed RSD <12%. Recoveries from biological samples ranged from 81.2 to 115%. The detection limit of the method was calculated as 3.3-10.2 ng in blood plasma and 2.6-12.6 ng in urine for 20 microL injection volume. The method was applied to spiked biological matrices. Moreover, the method was applied to real samples of urine after an oral administration.     

Surfactant‐assisted electromembrane extraction combined with capillary electrophoresis as a novel technique for the determination of acidic drugs in biological fluids

In this paper, for the first time, surfactant‐assisted electromembrane extraction coupled with capillary electrophoresis with UV detector was introduced for the extraction of acidic drugs from biological fluids. In this technique, in the presence of the nonionic surfactant in the donor phase, tendency of analyte ions into the supported liquid membrane (SLM) was increased. Naproxen and diclofenac were selected as model acidic drugs. In order to obtain the best extraction efficiency, several factors influencing the extraction efficiency were investigated. Optimal extractions were accomplished with 1‐octanol as the SLM, 15 Volt dc potential as the driving force, pH 12 in acceptor solution, and 0.2 mmol/L Triton X‐100 with pH 7.4 in donor solution. Equilibrium extraction conditions were obtained after 15 min of operation where the whole assembly agitated at 1000 rpm. Under the optimized conditions, preconcentration factors in the range of 176–184 and recoveries in the range of 88–92% were obtained. The applied method offers acceptable linearity with correlation coefficients higher than 0.9992. Limits of detection of 1.51 ng/mL and 2.42 ng/mL were obtained for naproxen and diclofenac, respectively. Finally, the developed method was successfully applied for the determination of naproxen and diclofenac in different matrices including plasma and urine samples.     

On-line preconcentration and recovery of palladium from waters using polyaniline (PANI) loaded in mini-column and determination by ICP-MS; elimination of spectral interferences

The applicability of polyaniline (PANI) for the on-line preconcentration and recovery of palladium from various water samples has been investigated. Batch experiments were performed to optimize conditions such as pH and contact time to achieve quantitative separation of Pd spiked at high (μg ml⁻¹) and low levels (ng ml⁻¹). During all the steps of the removal process, it was found that Pd was selectively removed by PANI even in the presence of various ions. Quantitative removal of Pd occured in the entire studied pH range (1-12) and the K_d value was found to be >10⁶. Kinetic studies show that a contact time of <4 min was adequate to reach equilibrium. The retained Pd was subsequently eluted with a mixture of HCl and thiourea, optimized using a factorial experimental design approach. ICP-OES was used for the micro-level determinations of Pd whereas ICP-MS was used for the determination of Pd at sub-ppb levels.Breakthrough curve using column experiments demonstrated that PANI has an excellent ability to accumulate up to ∼120 mg g⁻¹ of Pd from synthetic sample solutions. A preconcentration factor of about 125 was achieved for Pd when 250 ml of water was passed. PANI columns prepared were used up to 10 times in consecutive retention-elution cycles without appreciable deterioration in their performance. The proposed on-line method also has the ability to remove interfering elements Cu and Y for the determination of Pd in waters by ICP-MS. The reported method has been applied successfully for the determination of Pd in ground water, lake water sea-water and waste water samples. The recoveries were found to be >95% in all cases. These studies indicate that PANI has an excellent ability to preconcentrate Pd from various waters making the method very promising for the determination of Pd.     

氯硝柳胺衍生物的合成及抗肿瘤活性研究

以氯硝柳胺为起始原料,经醚化、亲核取代反应得到目标化合物,采用MTT法考察所合成化合物对人类乳腺癌细胞(MDA-MB-231)和人类胰腺癌细胞(ASPC-1)的体外抗肿瘤活性。合成了5个氯硝柳胺衍生物,其结构均经IR、1H-NMR、13C-NMR和MS确证。初步的体外抗肿瘤活性结果显示目标化合物9b和9c的抗肿瘤活性强于阳性对照药,其中化合物9b的活性对所测两种肿瘤株的抑制活性均强于阳性对照药,展现出较强的应用前景。     

电感耦合等离子体质谱法测定米托坦中的汞

介绍了电感耦合等离子体质谱法(ICP-MS)测定米托坦中的汞,重点从消解方式、酸体系和微波消解程序等方面对样品前处理方法进行了优化。在优化的实验条件下,本方法检出限为0.005 mg/kg,6次平行测定结果的相对标准偏差为7.7%,加标回收率为82.3%～85.7%。本方法灵敏度高、稳定性好,而且准确度高。     

Gas chromatographic determination of carbonyl compounds in biological and oil samples by headspace single-drop microextraction with in-drop derivatisation

A suitable method for the gas chromatographic determination of 10 characteristic carbonyls in biological and oil samples based on the in-drop formation of hydrazones by using 2,4,6-trichlorophenylhydrazine (TCPH), has been developed. The derivatisation-extraction procedure was optimized separately for aqueous and oil samples with respect to the appropriate organic drop solvent, drop volume, in-drop TCPH concentration, sample stirring rate, temperature during single-drop microextraction (SDME), reaction time and headspace-to-sample volume ratio. The optimization showed differentiation of optimum values between the studied matrices. The limits of detection were found to range from 0.001 to 0.003 μg mL⁻¹ for the aqueous biological samples and from 0.06 to 0.20 μg mL⁻¹ for the oil samples. The limits of quantification were in the range of 0.003-0.010 μg mL⁻¹ and 0.020-0.059 μg mL⁻¹ for aqueous and oil samples, respectively. The overall relative standard deviations of the within-day repeatability and between-day reproducibility were <4.4% and <8.2% for the aqueous biological samples and <3.9% and <7.4% for the oxidized oil samples.     

Anodic voltammetric behavior and determination of cefixime in pharmaceutical dosage forms and biological fluids

The voltammetric behavior of cefixime was studied using cyclic, linear sweep, differential pulse and square wave voltammetric techniques. The oxidation of cefixime was irreversible and exhibited diffusion controlled process depending on pH. The oxidation mechanism was proposed and discussed. Different parameters were tested to optimize the conditions for the determination of cefixime. The dependence of current intensities and potentials on pH, concentration, scan rate, nature of the buffer was investigated. According to the linear relationship between the peak current and the concentration, differential pulse (DPV) and square wave (SWV) voltammetric methods for cefixime assay in pharmaceutical dosage forms and biological fluids were developed. For the determination of cefixime were proposed in acetate buffer at pH 4.5, which allows quantitation over the 6 × 10⁻⁶-2 × 10⁻⁴ M range in supporting electrolyte and spiked serum sample; 8 × 10⁻⁶-2 × 10⁻⁴ M range in urine sample; 6 × 10⁻⁶-1 × 10⁻⁴ M range in breast milk samples for both techniques. The repeatability, reproducibility, precision and accuracy of the methods in all media were investigated. No electroactive interferences from the excipients and endogenous substances were found in the pharmaceutical dosage forms and in the biological samples, respectively.     

Review of analytical methods for the quantification of iodine in complex matrices

Iodine is an essential element of human nutrition. Nearly a third of the global population has insufficient iodine intake and is at risk of developing Iodine Deficiency Disorders (IDD). Most countries have iodine supplementation and monitoring programs. Urinary iodide (UI) is the biomarker used for epidemiological studies; only a few methods are currently used routinely for analysis. These methods either require expensive instrumentation with qualified personnel (inductively coupled plasma-mass spectrometry, instrumental nuclear activation analysis) or oxidative sample digestion to remove potential interferences prior to analysis by a kinetic colorimetric method originally introduced by Sandell and Kolthoff ∼75 years ago. The Sandell–Kolthoff (S–K) method is based on the catalytic effect of iodide on the reaction between Ce⁴⁺ and As³⁺. No available technique fully fits the needs of developing countries; research into inexpensive reliable methods and instrumentation are needed. There have been multiple reviews of methods used for epidemiological studies and specific techniques. However, a general review of iodine determination on a wide-ranging set of complex matrices is not available. While this review is not comprehensive, we cover the principal developments since the original development of the S–K method.