Fabrication and characterization of TiO2 photocatalytic thin film prepared from peroxo titanic acid sol

A novel sol–gel technique using the PTA (peroxo titanic acid) sol as precursor for the fabrication of TiO₂ photocatalytic thin film is introduced in this paper. The peroxo titanic acid sol was synthesized from titanyl sulfate (TiOSO₄), ammonia and peroxide solution (H₂O₂). The transparent and porous TiO₂ thin film was prepared via a sol–gel technique using PTA sol and polyethylene glycol (PEG) as precursor and template, respectively. The TiO₂ thin film samples were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectrophotometry (UV–vis), X-ray photoelectron spectrum (XPS) and thermogravimetry and differential thermal analysis (TG-DTA) technique. The PTA sol displayed amorphous TiO₂ below 100 °C. The anatase phase formed at 200 °C to 700 °C. The crystallinity of anatase phase was improved with increasing temperature. The anatase crystals on the surface of TiO₂ film were strip-like, the size being about 100 nm in length and 40 nm in diameter. Addition of PEG to the PTA sol developed porous structures in the film and changed the size and shape of the particles. The surface of the film contained Ti, O and C elements and Na element that diffused into the film from the glass substrate. The photocatalytic performance of TiO₂ film was tested for the degradation of 10 mg/L methyl orange. The degradation of methyl orange solution reached 98.9% after irradiated for 180 min under UV light. The porous TiO₂ thin film exhibited high photocatalytic activity towards degrading methyl orange.     

Controllable preparation of nanosized TiO<Subscript>2</Subscript> thin film and relationship between structure of film and its photocatalytic activity

TiO₂ nano-crystalline film and fixed bed photocatalytic reactor were prepared by the sol-gel process using tetrabutylorthotitanate as a precursor and glass tube as the substrate. XRD, AFM, SEM and thickness analysis results indicate that the preparation of nano-crystalline film can be controlled by optimizing experiment process. Under the optimized process, the phase of TiO₂ in film is anatase, and the grain size is 3–4 nm. The size of particles, which is about 20-80 nm, can be controlled. The thickness of monolayer film is in nanometer grade. The thickness and particles size in films growing on nanometer film can also be controlled in nanometer grade. As a result, the crack of film can be effectively avoided. Rhodamine degradation results using UV-Vis spectrophotometer show that the activity of nano-crystalline film in the photocatalytic reactor has a good relation with the diameter of TiO₂ particles, that is, the film shows high activity when the size is 20 –30 nm and greatly reduced when the size is above 60 nm. The activity of film does not decrease with the increase of film thickness, and this result indicates that nano-crystalline film has no ill influence on the transmissivity of ultraviolet light.     

Electrochemical sensor for acetaminophen based on an imprinted TiO2 thin film prepared by liquid phase deposition

An electrochemical sensor based on a molecularly imprinted TiO₂ thin film is proposed for the determination of acetaminophen. The imprinted TiO₂ films were obtained by liquid phase deposition (LPD) in the presence of acetaminophen, the functional monomer and the aqueous solution of (NH₄)₂TiF₆ and H₃BO₃. The results show that acetaminophen is embedded into the imprinted film in the presence of p-tert-butylcalix[6]arene as a functional monomer, and can be removed completely by washing with ethanol. The surface morphology, spectral properties and electrochemical characterizations of the imprinted sensor were investigated in detail. The combination of molecularly imprinted and LPD technique was shown to be a general strategy for constructing a molecular recognition system.     

Preparation of nanocrystalline TiO2 thin film at low temperature and its application in dye-sensitized solar cell

The electrophoretic deposition combined with common pressure hydrothermal treatment was employed to prepare nanocrystalline TiO₂ thin film from suspension of tetra-n-butyl titanate and P25 at low temperature. The tetra-n-butyl titanate was hydrolyzed and crystallized into anatase to interconnect nanocrystalline TiO₂ particles and to stick them to a conductive substrate by common pressure hydrothermal treatment to improve the electron transport properties of the deposited thin film. A dye-sensitized solar cell based on TiO₂ thin film prepared by the low temperature method yielded the conversion efficiency of 6.12%. Due to the relative slower electron transport rate in the deposited film, its conversion efficiency was slightly lower than that of the cell with TiO₂ thin film prepared by the conventional high temperature sintering method. Since it is free of high temperature sintering step, this method can be used to prepare nanocrystalline TiO₂ thin film on plastic polymer conductive substrate for fabrication of flexible dye-sensitized solar cell.     

Effect of dopant concentration on photocatalytic activity of TiO2 film doped by Mn non-uniformly

The thin films of TiO₂ doped by Mn non-uniformly were prepared by sol-gel method under process control. In our preceding study, we investigated in detail, the effect of doping mode on the photocatalytic activity of TiO₂ films showing that Mn non-uniform doping can greatly enhance the activity. In this study we looked at the effect of doping concentration on the photocatalytic activity of the TiO₂ films. In this paper, the thin films were characterized by UV-vis spectrophotometer and electrochemical workstation. The activity of the photocatalyst was also evaluated by photocatalytic degradation rate of aqueous methyl orange under UV radiation. The results illustrate that the TiO₂ thin film doped by Mn non-uniformly at the optimal dopant concentration (0.7 at %) is of the highest activity, and on the contrary, the activity of those doped uniformly is decreased. As a comparison, in 80 min, the degradation rate of methyl orange is 62 %, 12 % and 34 % for Mn non-uniform doping film (0.7 at %), the uniform doping film (0.7 at %) and pure titanium dioxide film, respectively. We have seen that, for the doping and the pure TiO₂ films, the stronger signals of open circuit potential and transient photocurrent, the better photocatalytic activity. We also discusse the effect of dopant concentration on the photocatalytic activity of the TiO₂ films in terms of effective separation of the photon-generated carriers in the semiconductor.     

Studies on photocatalytic activity of Ag/TiO2 films

Ag/TiO₂ photocatalytic films were produced by hybrid sol-gel method. The photocatalytic degradation of methyl orange (MO) in aqueous solution under 365 nm irradiation on TiO₂ and Ag/TiO₂ thin films was investigated. The state and amount of Ag species within the film and the enhancement mechanism of photocatalytic activity of Ag/TiO₂ were discussed. With a loading molar ratio of Ag/Ti = 0.135 in TiO₂ film, the maximum catalytic efficiency was observed. __________ Translated from Journal of Beijing Normal University (Natural Sciences), 2005, 41(6) (in Chinese)     

Preparation and properties of SiO2-TiO2 thin films from silicic acid and titanium tetrachloride

The preparation of SiO₂-TiO₂ thin films by the sol-gel method using silicic acid and titanium tetrachloride as starting materials was studied. The homogeneous sols were obtained by the condensation reaction of silicic acid with titanium tetrachloride in methanol-tetrahydrofuran. The dipcoating of slide glasses and silicon wafers followed by heat treatment gave oxide thin films of 88–93% transmittance, 3000–4500 Å thickness, and 1.45–1.80 refractive index, depending on heat-treatment temperature and TiO₂ content. FT-IR measurement showed that the Si-O-Ti bond is formed even in the sol and films. The variations of film thickness and refractive index on transformation from the gels into the oxides were found to be quite low.     

退火气氛对掺银TiO2薄膜结构和光催化性能的影响

本文采用sol-gel法制备了掺银的TiO2/glass纳米光催化薄膜,并分别在空气和真空条件下对薄膜进行退火处理, 结构和光催化性能的测试结果表明, 退火气氛对薄膜的结构和薄膜对染料溶液的光催化降解效率都有影响。经真空退火处理的TiO2及Ag-TiO2薄膜较空气中退火处理的同样薄膜的光催化性能都低, 但适量掺银的Ag-TiO2薄膜的光催化活性较TiO2有不同程度的增强。     

High photocatalytic activity and stability for decomposition of gaseous acetaldehyde on TiO2/Al2O3 composite films coated on foam nickel substrates by sol-gel processes

A set of anatase titanium dioxide (TiO₂) films coated on foam nickel that modified by Al₂O₃ films as transition layer (indicated as TiO₂/Al₂O₃ films) were synthesized via sol-gel route. The bulk and surface properties of the TiO₂/Al₂O₃ films were characterized by thermal gravimetric and differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), field-emission scanning electron microscope (FE-SEM), and BET. The photocatalytic activities of TiO₂/Al₂O₃ films were investigated based on the degradation of gaseous acetaldehyde under ultraviolet (UV) irradiation. The foam nickel is a promising substrate material in practical applications because of its excellent hydrodynamic properties for gas passing. The TiO₂/Al₂O₃ composite films showed much higher photocatalytic activity and stability for degradation of gaseous acetaldehyde than the onefold TiO₂ films. The significant enhancement in photocatalytic activity and stability can be ascribed to the coating of Al₂O₃ transition layer, which concentrates the target substances around TiO₂ particles and increases the specific surface area (SSA) of the substrate (the SSAs of bare foam nickel and Al₂O₃ modified foam nickel are 0.12 and 113.7 m²/g, respectively) to provide more sites for TiO₂ loading.     

Methane generated during photocatalytic redox reaction of alcohols on TiO2 suspension in aqueous solutions

Studies on the photo-catalytic redox reaction of C1–C3 alcohols such as methanol, ethanol and 2-propanol were carried out in aqueous solution containing TiO₂ photocatalyst (0.1% w/v) as suspension using 350 nm light. Other hydrocarbons such as ethane and ethene in the case of ethanol, and propene in the case of 2-propanol with low yields were produced along with the major photolytic products methane and carbon dioxide. The yields of methane and CO₂ were found to be dependent on the light exposure time and ambient conditions. Methane yields were higher in 2-propanol and ethanol systems than in methanol system, showing their better hole-scavenging properties. In the aerated condition, methane was produced during photolysis of all alcohols in the presence of TiO₂ and the yield was comparable to those observed in the corresponding CO₂-saturated systems. The overall results reveal that the surface adsorbed, as well as in-situ-generated CO₂ from photo-oxidation of alcohols are equally responsible for methane formation through photo-reduction in presence of TiO₂. In the O₂-saturated system, the methane yield was lower as compared to that in aerated system, in contrast to the CO₂ yield. In N₂O-and N₂-purged systems, the yield of methane was observed to be low, inferring that the methane generation has not taken place through photodecomposition/photodissociation of alcohols. Again, photolysis of alcohols without TiO₂ did not generate any methane.     

Hierarchical chlorine-doped rutile TiO2 spherical clusters of nanorods: Large-scale synthesis and high photocatalytic activity

In this study, we report the synthesis of hierarchical chlorine-doped rutile TiO₂ spherical clusters of nanorods photocatalyst on a large scale via a soft interface approach. This catalyst showed much higher photocatalytic activity than the famous commercial titania (Degussa P25) under visible light (λ>420 nm). The resulting sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), nitrogen adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy, ¹H solid magic-angle spinning nuclear magnetic resonance (MAS-NMR) and photoluminescence spectroscopy. On the basis of characterization results, we found that the doping of chlorine resulted in red shift of absorption and higher surface acidity as well as crystal defects in the photocatalyst, which were the reasons for high photocatalytic activity of chlorine-doped TiO₂ under visible light (λ>420 nm). These hierarchical chlorine-doped rutile TiO₂ spherical clusters of nanorods are very attractive in the fields of environmental pollutants removal and solar cell because of their easy separation and high activity.     

Structural characterization of Th-doped TiO2 photocatalyst and its extension of response to solar light for photocatalytic oxidation of oryzalin pesticide: a comparative study

The degradation efficiency of Th-doped TiO₂ / TiO₂ photocatalysts were investigated under UV and solar light illumination. The model compound chosen for the study was Oryzalin (OZ). Doping of inner transition metal ion Th was intended to modify the electronic properties of TiO₂. The Th-doped TiO₂ were synthesized by incorporating 0.02, 0.04, 0.06, and 0.1 atom percentage of Th into the TiO₂ lattice by solid-state reaction. The stochiometry of the prepared samples is Ti_1−xTh_xO₂, where ‘x’ is the percentage of Th. The samples were characterized by UV-Visible absorption, UV-Visible -Diffused reflectance spectra, Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Analysis (EDX) and X-ray Diffraction (XRD). The pore size and surface area of these samples were studied by Brunauer, Emmett and Teller (BET) adsorption method. It was found that metal ion doping at various percentage compositions enables a large shift in the absorption band of the TiO₂ towards visible light region. This is due to the formation of various mid band gaps at 2.84 eV, 2.804 eV, 2.66 eV, and 2.55 eV. The extent of degradation of the pesticide was followed by UV-Visible spectroscopy and GC-MS methods. Based on the spectral analysis, the probable degradation reaction mechanism for OZ is proposed. These results indicate that Th-doped TiO₂ with the modified electronic properties is a good catalyst under solar light irradiation. But these particles show marginal variation in rates under UV-illumination. All the photodegradation reactions follow the first order kinetics.      

Controllable preparation of nanosized TiO_2 thin film and relationship between structure of film and its photocatalytic activity

~~Controllable preparation of nanosized TiO_2 thin film and relationship between structure of film and its photocatalytic activity@魏刚$College of Material Science and Engineering,Beijing University of Chemical Technology! Beijing 100029,China @张元晶$College of Material Science and Engineering,Beijing University of Chemical Technology! Beijing 100029,China @熊蓉春$College of Material Science and Engineering,Beijing University of Chemical Technology! Beijing 100029,China~…     

Anatase TiO2 porous thin films prepared by sol-gel method using CTAB surfactant

Anatase TiO₂ porous thin films were prepared on glass substrates by sol-gel method with Cetyltrimethylammonium Bromide (CTAB) as a pore-forming agent, Tetrabutylorthotitanate as Ti precursor, ethanol as solvent and diethanolamine as chelating agent respectively. IR, TG-DSC, XRD and SEM analyzed the chemical and physical changes during sol-gel process and characteristics of the films. Effects of the amount of CTAB, alkane and water on morphology of the films were discussed and the principle of forming porous structure was proposed. It was shown that the diameter of pores was changed in the range of 30–400 nm.     

Preparation and characterization of mesoporous N-doped and sulfuric acid treated anatase TiO2 catalysts and their photocatalytic activity under UV and Vis illumination

Nitrogen-doped TiO₂ catalysts were prepared by a precipitation method. The samples were calcined at 400 °C for 4 h in air. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), low temperature N₂-adsorption was used for structural characterization and UV-diffuse reflectance (UV-DR) was applied to investigate the optical properties of the as-prepared samples. It was found that microporous N-doped catalysts have solely anatase crystalline structure. Acidic treatment of the calcined samples was performed using sulfuric acid agitation. The crystalline structure remained unchanged due to surface treatment, while the porosity and the surface areas were decreased dramatically. Optical characterization of the doped catalysts showed that they could be excited by visible light photons in the 400–500 nm wavelength range (λ_g,1=390 nm, λ_g,2=510 nm). It was also established that surface treatment enhances the Vis-light absorption of the N-TiO₂ powders. Finally the catalysts were tested in the photocatalytic degradation of phenol in aqueous suspensions. Two different light sources were used; one of them was a UV-rich high pressure Hg-lamp, while the other was a tubular visible light source. We found that using visible light illumination N-doped, acid treated TiO₂ samples were more catalytically active than non-doped TiO₂ catalysts.     

冷等离子体强化制备TiO2光催化材料及其机理

等离子体技术在材料制备和改性方面的优势得到众多研究者的认可。Ti O2具有化学稳定性高、氧化活性强、生产成本低等优势,被广泛应用于太阳能电池和光催化领域。本文综述了近年来介质阻挡放电等离子体在强化制备Ti O2光催化材料方面的研究成果,包括等离子体辅助制备Ti O2光催化薄膜和Ti O2的等离子体法掺杂两个方面,并分析了其作用机理。从目前的研究成果来看,等离子体技术制得的Ti O2光催化材料具有更好的均匀性和催化活性,这主要得益于等离子体中的高能电子,一方面,Ti O2粒子吸附电子,彼此之间产生静电场的斥力作用,可以抑制颗粒的团聚,另一方面,电子的强还原能力,能够打断Ti-O键,形成氧空位,从而提高其催化性能。     

Effect of initial precursor concentration on TiO2 thin film nanostructures prepared by PCVD system

TiO₂ thin film was prepared on Si substrate by plasma chemical vapor deposition (PCVD) system and the morphologies of TiO₂ thin film were controlled by adjusting the initial precursor concentration. As the initial titanium tetra-isopropoxide (TTIP) concentration increases in PCVD reactor, the shapes of TiO₂ particles generated in PCVD reactor change from the spherical small-sized particles around 20 nm and spherical large-sized particles around 60 nm to aggregate particles around 100 nm. The TiO₂ particles with different shapes deposit on the substrate and become the main building blocks of resulting TiO₂ thin film. We observed the TiO₂ thin film with smooth morphology at low initial TTIP concentration, granular morphology at medium initial TTIP concentration, and columnar morphology at high initial TTIP concentration. It is proposed that we can prepare the TiO₂ thin film with controlled morphologies in one-step process just by adjusting the initial precursor concentration in PCVD.     

Visible-light-mediated facile synthesis of disulfides using reusable TiO2/MoS2 nanocomposite photocatalyst

A nontoxic and inexpensive TiO₂/MoS₂ nanocomposite was prepared and employed as an efficient photocatalyst for the synthesis of symmetrical disulfides under visible light irradiation at room temperature. Both aryl and alkyl thiols survived the reaction conditions, affording the corresponding disulfides in good to excellent yields. The photocatalyst could be easily recovered by simple centrifugation and filtration and reused several times without significant loss in its activity.     

Structure of TiO2 in TiO2-SiO2 prepared by a complexing agent-assisted sol-gel procedure

Many types of TiO₂-SiO₂ (Ti:Si=50:50 mol%) were prepared by the sol-gel procedure with and without 2-methyl-2, 4-pentanediol (MPD) as an organic ligand. The effect of MPD on the gel structure and the properties of the TiO₂ crystals were studied by XRD and raman spectroscopy, and the effect of the sol standing time on the properties of the TiO₂ crystals were also studied by XRD spectroscopy. In the gels with MPD, anatase of TiO₂ appeared at approximately 580°C, and the crystal structures were similar despite the difference in the gel preparation procedure. The titania gels with MPD were presumed to be dispersed in the silica gel matrix without any Ti-O-Si bond. In the presence of MPD, the formation of titania gels is controlled and the specified TiO₂ crystal is produced.     

Characterization of TiO2 thin film immobilized on glass tube and its application to PCE photocatalytic destruction

TiO₂ was immobilized on to the surface of a pyrex glass tube through a dip coating process, and a pyrex glass tube with TiO₂ thin film was used as a batch reactor and continuous flow reactor for the photocatalytic destruction of PCE in water. TiO₂ could be successfully immobilized with a thickness of 0.3 μm in the pyrex glass tube. The TiO₂-immobilized pyrex glass tube itself showed high photocatalytic activity for the destruction of PCE in water.