Micellar colorimetric determination of iron, cobalt, nickel and copper using 1-nitroso-2-naphthol

1-Nitroso-2-naphthol, an excellent color-forming chelating agent, combines to Fe(III), Co(II), Ni(II), Cu(II) and so on to form slightly soluble complexes in aqueous solution. To determine these metal ions, a tedious and time consuming separation technique, such as liquid-liquid extraction, has often been performed. However, these metal-1-nitroso-2-naphthol complexes could be determined conveniently by ultraviolet-visible (UV-Vis) spectrophotometry in Tween 80 micellar medium that has polyoxyethylene groups. After conditions such as pH, the amount of 1-nitroso-2-naphthol and the stability were adjusted to their optimum values, the sensitivities of the metal ions in Tween 80 medium and in chloroform were compared. It was shown that the sensitivities of Fe(III) and Co(II) in Tween 80 medium were higher than in chloroform, but that of Cu(II) was lower. The interfering effects among analytes ions, Fe(III), Co(II), Ni(II) and Cu(II) were more serious than by other ions, but the interfering effects could be removed by adjusting pH or adding the masking agents such as NH(3) or oxalate. Detection limits of Fe(III), Co(II), Ni(II), and Cu(II) were 0.024, 0.016, 0.039 and 0.023 mug ml(-1), respectively, and the correlation coefficients of these calibration curves were above 0.996. Recovery yields of the metal ions in the mixed standard solution ranged from 96 to 103%, and their coefficients of variation were low ranging between 0.94 and 1.75%. Cu(II) in brass sample and the amount of Fe(III) in steel sample were also determined. This proposed technique is simple, convenient and speedy.     

A rapid spectrophotometric method for the determination of trace level lead using 1,5-diphenylthiocarbazone in aqueous micellar solutions.

A very simple, ultra-sensitive and fairly selective direct spectrophotmetric method is presented for the rapid determination of lead(II) at ultra-trace level using 1,5-diphenylthiocarbazone (dithizone) in micellar media. The presence of the micellar system avoids the previous steps of solvent extraction and reduces the cost and toxicity while enhancing the sensitivity, selectivity and the molar absorptivity. The molar absorptivities of the lead-dithizone complex formed in the presence of the cationic cetyltrimethylammonium bromide (CTAB) surfactants are almost ten times the value observed in the standard method, resulting in an increase in the sensitivity of the method. The reaction is instantaneous and the absorbance remains stable for over 24 h. The average molar absorption coefficient was found to be 3.99 x 10(5) L mol(-1) cm(-1) and Sandell's sensitivity was 30 ng cm(-2) of Pb. Linear calibration graphs were obtained for 0.06-60 mg L(-1) of Pb(II); the stoichiometric composition of the chelate is 1:2 (Pb:dithizone). The interference from over 50 cations, anions and complexing agents has been studied at 1 mg L(-1) of Pb(II). The method was successfully used in the determination of lead in several standard reference materials (alloys and steels), environmental water samples (potable and polluted), biological samples (human blood and urine), soil samples and solutions containing both lead(II) and lead(IV) and complex synthetic mixtures. The method has high precision and accuracy (sigma = +/-0.01 for 0.5 mg L(-1)).     

Kinetic spectrophotometric determination of Fe(II) in the presence of Fe(III) by H-point standard addition method in mixed micellar medium

The H-point standard addition method was applied to kinetic data for simultaneous determination of Fe(II) and Fe(III) or selective determination of Fe(II) in the presence of Fe(III). The method is based on the difference in the rate of complex formation between iron in two different oxidation states and methylthymol blue (MTB) at pH 3.5 in mixed cetyltrimethylammonium bromide (CTAB) and Triton X-100 micellar medium. Fe(II) can be determined in the range 0.25-2.5 microg ml(-1) with satisfactory accuracy and precision in the presence of excess Fe(III) and other metal ions that rapidly form complexes with MTB under working condition. The proposed method was successfully applied to the simultaneous determination of Fe(II) and Fe(III) or selective determination of Fe(II) in the presence of Fe(III) in spiked real environmental and synthetic samples with complex composition.     

Use of a novel medium, the ionic liquid 1-butyl-3-trimethylsilylimidazolium hexafluorophosphate, for liquid-liquid extraction of lead in water and its determination by graphite furnace atomic absorption spectrometry

The ionic liquid 1-butyl-3-trimethylsilylimidazolium hexafluorophosphate, abbreviated as [C4tmsim][PF6], was developed as a novel medium for liquid-liquid extraction of lead(II) in water, in which dithizone was used as a metal chelator to form a neutral lead-dithizone complex. Under optimal conditions, the complex was extracted into the [C4tmsim][PF6] phase from aqueous solution and back-extracted with nitric acid solution into the aqueous phase that was used directly for the subsequent determination of Pb. The system using the ionic liquid demonstrated good extraction performance; the extraction and back-extraction efficiencies were 99.8 and 99.7%, respectively, for Pb(II) at 20 microg/L. The above procedure, including the extraction and back-extraction, was used to enrich trace levels of Pb(ll) in a relatively large volume of water samples (1000 mL water), and an enrichment factor of 400 was obtained. The enrichment coupled with graphite furnace atomic absorption spectrometry was successfully applied to the determination of Pb in water. The calibration graph was linear at levels near the detection limits up to > or = 100 ng/L Pb(II). The limits of quantitation and detection for lead in real water samples were 2.5 and 1.0 ng/L, respectively. Lead recoveries of 96.2-103.8% from spiked samples demonstrate the accuracy of the proposed method.     

A sensitive and simple extractive-spectrophotometric method for the determination of microgram amount of cobalt by using alpha-benzilmonoxime.

Alpha-benzilmonoxime has been used for the extraction and determination of cobalt at microgram amount. The reagent reacts with cobalt(II) in the pH range of 8.8 - 9.3 to form a yellow-color chelate, which is extracted in chloroform, toluene, and some other non-polar solvents. The chelate is stable in chloroform for about one day. Under the optimum conditions of the a-benzilmonoxime concentration and pH of 9.0, Beer's law was obeyed in the concentration range of 0.08 - 2.2 microg/ml cobalt. The molar absorptivity of the extracted species was 2.55 x 10(4) dm3/mol cm at 380 nm, with a detection limit of 0.01 microg/ml cobalt. Relative standard deviations of 0.4, 0.8 and 2.3% were found for the determination of cobalt concentrations of 2.2, 1.1 and 0.08 microg/ml, respectively. The effect of diverse ions on the determination of 1.00 microg/ml of cobalt has been studied. The method was applied to the determination of cobalt in vitamin B12 and B-complex ampoules, a Co2O3-Co3O4 laboratory chemical mixture and some synthetic alloy samples. The method is sensitive, simple, rapid and accurate.     

Differential pulse anodic stripping voltammetry of lead (lI) benzoylacetonate in chloroform: Application to the analysis of free-lead gasoline and gas oil samples

The voltammetric characteristics of lead(II) benzoylacetonate in chloroform at the mercury electrode are investigated. The conditions for nearly reversible reduction of lead(II) were optimized. Anodic stripping voltammetry for the determination of trace-lead was developed using differential pulse technique to strip amalgamed lead from hanging mercury drop electrode. The experimental conditions, such as scanning rate of electrode potential and deposition time of lead were optimized. The calibration graph was linear over concentration range 5x10(-8)-10(-6) M of lead(II). The detection limit was 2.5x10(-9) and the relative standard deviation for the determination of 4x10(-7) M Pb(II) was 2%. Preceded by decomposition of organolead compounds with concentrated nitric acid, then ashing at 300 degrees C and a solvent extraction of Pb(II) benzoylacetonate in chloroform, the suitability of the proposed method for the determination of lead in free-lead gasoline and gas oil was demonstrated as a typical example of application.     

Extractive photometric determination of gold(III) with 1-(2',4',6'-trichlorophenyl)-4,4,6-trimethyl-(1H,4H)-2-pyrimidinethiol in presence of tri-iso-octylamine

Tervalent gold was determined spectrophotometrically as its anionic 1:4 gold-thiol complex extracted into chloroform from aqueous acidic medium (1.5M sulphuric acid) in the presence of tri-iso-octylamine. The complex exhibits maximum absorption at 480 nm (molar absorptivity 4.60 x 10(3) l.mole(-1).cm(-1)) and Beer's law is obeyed in the concentration range 5-50 microg of gold(III) per ml. The relative standard deviation and relative error, calculated from ten determinations of solutions containing 15 microg of gold(III) per ml were 1.0% and 0.8%. The method is simple, selective and reproducible. It permits separation of gold(III) from associated elements and its determination in synthetic mixtures.     

Spectrophotometric determination of lead in biological samples with dibromo-p-methyl-methylsulfonazo

A new highly sensitive and selective chromogenic reagent, dibromo-p-methyl-methylsulfonazo (DBM-MSA), was studied for determination of lead. In 0.24 mol l(-1) phosphoric acid medium, which greatly increases the selectivity, lead reacts with DBM-MSA to form a 1:2 blue complex which has a sensitive absorption peak at 642 nm. Under the optimal conditions, Beer's law was obeyed over the range 0-0.6 mug ml(-1) Pb(II). The molar absorptivity and Sandell's sensitivity are 1.02x10(5) l mol(-1) cm(-1) and 0.00203 mug cm(-2), respectively. The limit of quantification, limit of detection and relative standard deviations were found to be 7.30 and 2.21 ng ml(-1) and 1.1%, respectively. It is found that, except for Ca(II) and Ba(II), all foreign ions studied do not interfere with the determination. The interference caused by Ca(II) and Ba(II) can be easily eliminated by prior extraction with potassium iodide-methylisobutylketone. The method has been applied to the determination of lead in some biological samples with satisfactory results.     

Spectrophotometric determination of rifampicin through chelate formation and charge transfer complexation in pharmaceutical preparation and biological fluids

Two simple and accurate spectrophotometric methods for determination of Rifampicin (RIF) are described. The first method is based on charge transfer (CT) complex formation of the drug with three pi-electron acceptors either 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ), 7,7,7,8-Tetracyanoquinodimethane (TCNQ) or 2,3,5,6-Tetrachloro-1,4-benzoquinone (p-chloranil) in acetonitrile. The method is followed spectrophotometrically by measuring the maximum absorbance at 584 nm, 761 nm (680 nm) or 560 nm for DDQ, TCNQ and p-chloranil, respectively. Under the optimized experimental conditions, the calibration curves showed a linear relationship over the concentration ranges of 5-140 microg/ml, 2-45 microg/ml (5-120 microg/ml) and 15-200 microg/ml, respectively. The second method is based on the reaction of RIF with iron(III) forming a water insoluble violet complex which is extracted into chloroform. The method determines RIF in concentration range of 10-240 microg/ml at 540 nm. The proposed methods applied to determination of RIF in capsule, human serum and urine samples with good accuracy and precision. The results were compared statistically with the official method and showed no significant different between the methods compared in terms of accuracy and precision.     

H-point standard addition method for simultaneous spectrophotometric determination of Co(II) and Ni(II) by 1-(2-pyridylazo)2-naphthol in micellar media

A very simple and selective spectrophotometric method for simultaneous determination of Co(II) and Ni(II) by 1-(2-pyridylazo) 2-naphthol (PAN), in micellar media, using H-point standard addition method (HPSAM) is described. The ligand and its metal complexes (Co(II)-PAN and Ni(II)-PAN) were made water-soluble by the neutral surfactant Triton X-100, and therefore, no extraction with organic solvents was required. Formation of both the complexes was complete within 10 min at pH 9 (adjusted by ammonia buffer). The linear range was 0.10-2.00 microg ml(-1) for Co(II) and 0.05-1.50 microg ml(-1) for Ni(II). The relative standard deviation (R.S.D.) for the simultaneous determination of 0.50 microg ml(-1) each of Co(II) and Ni(II) was 2.32 and 3.13%, respectively. Interference effects of common anions and cations were studied and the method was applied to simultaneous determination of Co(II) and Ni(II) in alloy samples. The method was compared with derivative spectrophotometric method.     

Spectroscopic studies of interaction of Safranine T with nonionic micelles and mixed micelles

The visible spectra of Safranine T (ST) in micellar solution of Brij 58, Tween 20 and Tween 40 and mixed micellar solution of Brij 58/Tween 20 and Brij 58/Tween 40 indicate formation of 1:1 charge transfer (CT) complex between acceptor ST and donor nonionic micelles and mixed micelles. The experimental CT transition energies are well correlated (through Mulliken's equation) with the vertical ionization potential of the donors. The solvent parameters, i.e. the intramolecular charge transfer energy ET(30) have been determined from the Stokes spectral shift. Variations of ionization potential and micropolarity in the mixed micellar region have been investigated as a function of surfactant composition and the obtained results in mixed micellar medium has been compared to the normal micelles. The critical micelle concentration (CMC) values determined at various surfactant compositions are lower than the ideal values indicating a synergistic interaction. The interaction parameter (beta) and micellar stability has been calculated using regular solution theory.     

Spectrophotometric and spectrofluorimetric methods for the determination of ramipril in its pure and dosage form

This paper describes three sensitive spectrophotometric and spectrofluorimetric methods for determination of ramipril in its pure form and pharmaceutical tablets. The first method is based on the oxidation of the drug with 1-chlorobenzotriazole reagent (CBT) in strong alkaline medium followed by measuring the absorbance at 350 nm. The method obeys Beer's law over concentration range 15-50 microg ml(-1). For the second and third, both are non-extractive methods based on the formation of ternary complex between copper (II), eosin and ramipril in the presence of methylcellulose as surfactant. Spectrophotometrically, under the optimum condition, the ternary complex showed an absorption maximum at 543 nm. The method obeys Beer's law over concentration range of 20-80 microg ml(-1). A fluorescence quenching method for the determination of ramipril by forming this ternary complex was also investigated for the propose of enhance the sensitivity of the determination. The methods are simple, sensitive, and accurate. The results obtained are reproducible with a coefficient of variation less than 2%. The proposed have been successfully applied to the assay of ramipril in tablets. The results compare favorably with official method.     

Catalytic behavior of tris(2,2'-bipyridine)iron(II) complex in chemiluminescence reaction of luminol in reversed micellar medium of cetyltrimethylammonium chloride

Tris(2,2'-bipyridine) complex of iron(II) was found to cause an increase in the chemiluminescence (CL) emission of luminol dispersed in the reversed micellar medium of cetyltrimethylammonium chloride (CTAC) in 1:1 (v/v) dichloromethane-cyclohexane/water, when the iron(II) complex in dichloromethane was mixed directly with the reversed micellar solution containing luminol. Visible absorption measurements showed that, when dispersed in the CTAC reversed micellar medium, the iron(II) complex dissociates easily. In the reverse micelle, subsequently the free iron(II) ion produced may catalyze the CL oxidation of luminol even in the absence of hydrogen peroxide. The CL emission produced under the optimized experimental conditions was detectable at a minimum iron(II) concentration of 1.0 x 10(-9) M using a flow injection system.     

Spectrophotometric determination of some dibenzazepines with picryl chloride

A simple and sensitive spectrophotometric method has been developed for the determination of some dibenzazepines, based on reaction with picryl chloride in chloroform medium and measurement at 395 nm. Beer's law is obeyed in concentration ranges 0.1-1.0 microg/ml for imipramine hydrochloride, trimipramine maleate and opipramol dihydrochloride, 0.16-1.6 microg/ml for desipramine hydrochloride and 0.4-2.4 microg/ml for clomipramine hydrochloride. The method was applied successfully to the determination of dibenzazepines in tablets and the results were comparable to those obtained by official procedures.     

Univariate and simplex optimization for the flow-injection spectrophotometric determination of copper using nitroso-R salt as a complexing agent.

A simple colorimetric flow-injection system for the determination of Cu(II) based on a complexation reaction with nitroso-R salt is described. The chemical and FIA variables were established using the univariate and simplex methods. A small volume of Cu(II) was mixed with merged streams of nitroso-R salt and acetate buffer solutions. The absorbance of the complex was continuously monitored at 492 nm. The calibration curve over the concentration range 1.0-7.0 microg ml(-1) was obtained. The relative standard deviation for determining 4.0 microg ml(-1) Cu(II) was 0.47% (n = 11). The detection limit (3sigma) was 0.68 microg ml(-1) and the sample throughput was 150 h(-1). The validity of the method has been satisfactorily examined for the determination of Cu(II) in wastewater and copper ore samples. The accuracy was found to be high, because the student t-values were calculated to be less than the theoretical values when the results were compared with those obtained by FAAS.     

Removal of lead from aqueous solutions using Cassia grandis seed gum-graft-poly(methylmethacrylate)

Using persulfate/ascorbic acid redox system, a series of Cassia grandis seed gum-graft-poly(methylmethacrylate) samples were synthesized. The copolymer samples were evaluated for lead(II) removal from the aqueous solutions where the sorption capacities were found proportional to the grafting extent. The conditions for the sorption were optimized using copolymer sample of highest percent grafting. The sorption was found pH and concentration dependent, pH 2.0 being the optimum value. Adsorption of lead by the grafted seed gum followed a pseudo-second-order kinetics with a rate constant of 4.64 x 10(-5) g/mg/min. The equilibrium data followed the Langmuir isotherm model with maximum sorption capacity of 126.58 mg/g. The influence of electrolytes NaCl, Na(2)SO(4) on lead uptake was also studied. Desorption with 2 N HCl could elute 76% of the lead ions from the lead-loaded copolymer. The regeneration experiments revealed that the copolymer could be successfully reused for at least four cycles though there was a successive loss in lead sorption capacity with every cycle. The adsorbent was also evaluated for Pb(II) removal from battery waste-water containing 2166 mg/L Pb(II). From 1000 times diluted waste water, 86.1% Pb(II) could be removed using 0.05 g/20 ml adsorbent dose, while 0.5 g/20 ml adsorbent dose was capable of removing 60.29% Pb from 10 times diluted waste water. Optimum Pb(II) binding under highly acidic conditions indicated that there was a significant contribution of nonelectrostatic interactions in the adsorption process. A possible mechanism for the adsorption has been discussed.     

Simultaneous determination of cobalt and palladium in micellar media using H-point standard addition method and partial least square regression

A simple, sensitive and selective spectrophotometric method for the simultaneous determination of Co(II) and Pd(II) using partial least square (PLS) calibration and H-point standard addition method is described. The method is based on the complex formation of Co(II) and Pd(II) with 4-(2-pyridylazo) resorcinol (PAR) in acidic media and in the presence of sodium dodecyl sulfate (SDS) as a micellizing agent. Acidic media and the presence of a micellar system improve selectivity and sensitivity, respectively. By applying PLS calibration, Co(II) and Pd(II) can be determined in the range of 0.20-2.0 and 0.40-4.0 microg ml(-1), respectively. The relative errors of prediction for the determination of Co(II) and Pd(II) in the 10 prediction samples were 1.69 and 1.72%, respectively. The results of applying H-point standard addition method show that Co(II) and Pd(II) can be determined simultaneously with concentration ratio of Co(II) to Pd(II) varying between 7:1 and 1:8 in the mixed samples. Both proposed methods (PLS and HPSAM) were applied to the determination of Co(II) and Pd(II) in several alloy solutions with satisfactory results.     

Extraction and spectrophotometric determination of lead(II) with pyridine-2-acetaldehyde salicyloylhydrazone

Lead(II) reacts with pyridine-2-acetaldehyde salicyloylhydrazone (PASH) in the pH range 8.6-9.3 to form a yellow-green, 1:2 chelate which can be extracted into chloroform. Beer's law is obeyed in the concentration range 1.5-6.2 mug ml(-1) of lead(II). The molar absorptivity of the extracted species is 1.93 x 10(4) l mol(-1) cm(-1) at 380 nm. The proposed method is sensitive, simple, rapid, accurate and has been satisfactorily applied for the determination of lead in synthetic mixtures, alloys, water and soil samples.     

Catalytic determination of Pb(II) in the presence of Cu(II)

A kinetic method is presented to determine micro-molar amounts of Pb(II) from various river and wastewater samples, in the presence of trace copper. The procedure is based on the catalytic effect of both species on the oxidation of mercaptosuccinic acid by chromate in acidic media. The extent of the reaction is followed spectrophotometrically at 420 nm and pseudo-first-order rate coefficients of the rate-determining step are determined as a function of catalyst concentrations. The optimum operating conditions (ionic strength, temperature, and concentration of reagents) regarding sensitivity towards lead were established. Interference by several ionic species has been studied. The effect of Fe(III), the only severe interferent, is suppressed by complexation with 1,10-phenantroline. The bi-component calibration model employs an artificial neural network to compute the Pb(II) concentration from a k(obsd) value and the a priori-known Cu(II) concentration of the sample. Working concentration ranges are 20-2160 micro g L(-1) for Pb(II) and 80-650 micro g L(-1) for Cu(II), respectively. Detection limits are 20 micro g L(-1) Pb(II) and 80 micro g L(-1) Cu(II), respectively. The relative standard deviations (3 measurements) for four different testing points are lower than 2.5%. The method was applied to samples of river and wastewater of the mining region of Baia-Mare, Northern Romania. The results were compared to those obtained by an officially standardized AAS method. Good agreement was achieved. The method is inexpensive, fairly rapid, and sensitive. Its working range covers the exact range of concentrations usually encountered in the mentioned geographic area.     

Spectrofluorimetric determination of drugs containing active methylene group using N1-methyl nicotinamide chloride as a fluorigenic agent

A spectrofluorimetric method was described for the determination of drugs containing active methylene groups adjacent to carbonyl groups. The method was applied successfully to the determination of three life saving cardiovascular drugs, with narrow therapeutic indices: pentoxifylline (I), propafenone hydrochloride (II) and acebutolol hydrochloride (III), in laboratory-prepared mixtures, in commercial tablets and in plasma samples. The method involved the reaction of each of the tested drugs with N1-methyl nicotinamide chloride (NMNCl) in the presence of alkali, followed by addition of formic acid, where highly fluorescent reaction products were produced. The produced fluorescence were measured quantitatively at 472 nm (lambdaex 352 nm), 409 nm (lambdaex 310 nm) and 451 nm (lambdaex 266 nm) for (I), (II), and (III) respectively. The method was linear over concentration ranges of 10-1000 microg/ml , 0.2-12 microg/ml and 0.08-10 microg/ml in standard solutions for (I), (II), and (III) respectively. In spiked human plasma samples, calibration graphs were linear over concentration ranges of 20-1000 microg/ml, 0.2-15 microg/ml and 0.08-10 microg/ml for (I), (II), and (III) respectively. The method showed good accuracy, specificity and precision in both laboratory-prepared mixtures and spiked human plasma samples. The proposed method is simple, with low instrumentation requirements, suitable for quality control application, bioavailability and bioequivalency studies.