Surface chemistries of lithium: Detailed characterization of the reactions with O2 and H2O using XPS, EELS, AND microgravimetry

The surface chemical reactions of O₂ and H₂O on clean lithium have been studied by a combination of XPS, EELS and microgravimetry. Reactions with O₂ produce a monolayer of oxide which does not passivate the surface and which allows for the growth of several monolayers of additional oxide, probably as a result of the mixing of zero-valent metal into the oxide layer. The reaction of H₂O with the clean lithium surface results in the complete dissociation of the molecule and loss of hydrogen to form one monolayer of the oxide. This is followed by the formation of multilayers of hydroxide/oxide mixtures which are shown to be unstable over periods of minutes, converting back to the oxide form predominantly.     

The interaction of C2Cl4 with fe(110)

Quantitative adsorption studies, temperature programmed desorption (TPD) and Auger spectroscopy have been used to study the interaction of C₂Cl₄ with Fe(110) at 90 and 325 K. At 90 K, multilayer C₂Cl₄ adsorption occurs. The following desorption products are observed in the temperature range of 90–1050 K: C₂Cl₄ from the multilayer and the monolayer, FeCl₂, and a high mass iron chloride species with mass spectrometer cracking products FeCl⁺₂, FeCl⁺, and Fe⁺. Irreversible dissociative C₂Cl₄ adsorption occurs at 325 K and the only desorption product which is observed is the high mass iron chloride species. Auger spectroscopy shows that surface carbon from C₂Cl₄ starts to diffuse into the bulk of the crystal at ˜ 480 K while small coverages of chlorine remain on the surface of the crystal even after heating to 1050 K. Comparison of the behavior of C₂Cl₄ and CCl₄ on Fe(110) indicates that radical products (·CCl₃ and :CCl₂) observed to be produced from CCl₄ adsorption are not produced from C₂Cl₄ adsorption. This difference is probably due to the enhanced surface reactivity of the C=C bond in C₂Cl₄. A special reactivity of iron defect sites for C₂Cl₄ is observed through the production of associated FeCl₂ species which desorb via zero-order kinetics with an activation energy of 44.8 ± 8.5 kcal/mol, the sublimation enthalpy of FeCl₂.     

Interaction of copper and NO2: Effect of joint presence of SO2, relative humidity and temperature

This paper reports laboratory tests involving the dry deposition on copper surfaces of NO₂, alone and in combination with SO₂, at different concentrations (200 and 800 μg m⁻³), temperatures (15, 25 and 35 °C) and relative humidities (50%, 70% and 90%). Gravimetric results and characterisation of the corrosion products by optical microscopy, scanning electron microscopy (SEM/EDX), grazing incidence X-ray diffraction (GIXD) and X-ray photoelectron spectroscopy (XPS) show that the corrosive effect of NO₂ acting alone depends greatly on the RH. At 90% RH copper behaves in the same way as in unpolluted atmospheres, while at lower RH localised attack is detected. Analysis reveals the presence of basic copper nitrate (gerhardtite, Cu₂(OH)₃NO₃). However, in SO₂-polluted atmospheres no differential behaviour with RH or temperature is observed. In these atmospheres copper corrosion is similar to that obtained in unpolluted or in NO₂-polluted atmospheres at high RH, although GIXD detects basic copper sulphate (posnjakite, Cu₄(OH)₆SO₄·2H₂O). In the case of mixed atmospheres (SO₂+NO₂) a significant accelerating effect is observed when [NO₂]>[SO₂]. Otherwise an inhibitive effect is detected. At high RH in the presence of SO₂, NO₂ favours SO₂ oxidation and finally sulphuric acid formation, which attacks the cuprite layer. S-containing compounds, especially basic copper sulphate, are easily detected by GIXD and XPS in the outermost corrosion product layer. However, at low RH, NO₂ reacts preferentially with adsorbed water to produce nitrous and nitric acids that attack the cuprite layer. In this case, an outer corrosion product layer containing copper nitrite (soluble) and basic copper nitrate is formed over an intermediate layer that contains significant amounts of basic copper sulphate from the previous interaction of sulphuric acid and cuprite.     

Passivation of TiO2 by ultra-thin Al-oxide

The passivation of sol–gel TiO₂ by ultra-thin layers of Al-oxide has been investigated using transient and spectral photovoltage (PV) techniques. The ultra-thin layers of Al-oxide were prepared by the ion-layer gas reaction (ILGAR) technique and modified by thermal treatments in air, vacuum or Ar/H₂S atmosphere. The samples where characterized by elastic recoil detection analysis (ERDA), X-ray photoelectron spectroscopy (XPS), and contact potential difference (CPD) technique. Without an Al-oxide surface layer, electronic states in the forbidden gap of TiO₂ are formed during thermal treatments in vacuum and Ar/H₂S. The trap density is strongly reduced at the TiO₂/Al-oxide interface. The formation of electronic defects is prevented by a closed ultra-thin layer of Al-oxide.     

基于紫外吸收光谱技术的混合气体SO2和H2S浓度的实时监测

采用紫外波段吸收光谱检测技术,实现了SO₂和H₂S混合气体各组分浓度的实时监测。在实验中选用氘灯为测试光源,MAYA2000Pro光谱仪用于采集数据。基于光谱的峰谷特性,选择吸收光谱上波长非常接近的两个来推导SO₂气体的浓度公式,该方法可以忽略其他气体散射和吸收的影响。H₂S气体的吸收光谱可以通过减去混合气体中相应的SO₂气体吸收光谱获得。在常温常压下,H₂S气体的浓度可以从H₂S气体的吸收光谱的吸收峰获得。混合气体的测量精度约为1×10^-6(1 ppm)。基于上述方法,实现了混合气体SO₂和H₂S浓度的实时监测。     

A quantum chemical study of ZrO2 atomic layer deposition growth reactions on the SiO2 surface

Zirconium oxide (ZrO₂) is one of the leading candidates to replace silicon oxide (SiO₂) as the gate dielectric for future generation metal-oxide-semiconductor (MOS) based nanoelectronic devices. Experimental studies have shown that a 1–3 monolayer SiO₂ film between the high permittivity metal oxide and the substrate silicon is needed to minimize electrical degradation. This study uses density functional theory (DFT) to investigate the initial growth reactions of ZrO₂ on hydroxylated SiO₂ by atomic layer deposition (ALD). The reactants investigated in this study are zirconium tetrachloride (ZrCl₄) and water (H₂O). Exchange reaction mechanisms for the two reaction half-cycles were investigated. For the first half-reaction, reaction of gaseous ZrCl₄ with the hydroxylated SiO₂ surface was studied. Upon adsorption, ZrCl₄ forms a stable intermediate complex with the surface SiO₂–OH^* site, followed by formation of SiO₂–O–Zr–Cl^* surface sites and HCl. For the second half-reaction, reaction of H₂O on SiO₂–O–Zr–Cl^* surface sites was investigated. The reaction pathway is analogous to that of the first half-reaction; water first forms a stable intermediate complex followed by evolution of HCl through combination of a Cl atom from the surface site and an H atom from H₂O. The results reveal that the stable intermediate complexes formed in both half-reactions can lead to a slow film growth rate unless process parameters are adjusted to lower the stability of the complex. The energetics of the two half-reactions are similar to those of ZrO₂ ALD on ZrO₂ and as well as the energetics of ZrO₂ ALD on hydroxylated silicon. The energetics of the growth reactions with two surface hydroxyl sites are also described.     

EPR evidence of local lattice mode in K3H(SO4)2 and Rb3H(SO4)2 fast-proton conductors

The observation of an anomalous temperature dependence of Mn²⁺ EPR spectra linewidth and nonaxial crystal-field parameter in K₃H(SO₄)₂ and Rb₃H(SO₄)₂ allows one to suggest the presence of “local mode” predicted by Yamada (Ferroelectrics 170 (1995) 23). The activation energy for this kind of excitation was found and equals 11.3 (0.5) and 7.4 (0.3) meV for Mn²⁺ doped K₃H(SO₄)₂ and Rb₃H(SO₄)₂, respectively.     

O2/CO2气氛下循环流化床煤燃烧SO2排放

在热输入功率50 kW的循环流化床O₂/CO₂燃烧试验装置上研究燃煤SO₂排放特性及石灰石脱硫机理。结果发现,未添加石灰石时,O₂/CO₂气氛下SO₂排放量比相同O₂浓度的空气气氛下低;随着O₂浓度的升高,排放量升高。相同钙硫摩尔比下,O₂/CO₂气氛下石灰石的脱硫机理以直接脱硫为主,脱硫效率比空气气氛下高;随着O₂浓度的增加,石灰石脱硫效率提高。     

The reaction of H2S with surface oxygen on Ni(110)

The reactions of H₂S with predosed surface oxygen on Ni(110) surfaces were studied for a variety of coverage conditions. The primary reaction product is H₂O, but the details of the water formation and desorption depends on the coverage of both O and H₂S.

For high coverages of oxygen (p(2 × 1)−O; 0.5 ML), the reaction to form water is quantitative. The loss of oxygen from the surface (as measured by AES) is equal to the increase in sulfur coverage. XPS and HREELS measurements indicate the presence of chemisorbed H₂O immediately following large exposures of H₂S on the oxygen predosed surface at 110 K. Deuterium incorporation results suggest that the primary mechanism for these coverage conditions involves direct transfer of hydrogen from SH or H₂S moieties to the oxygen.

A second mechanism involving reaction of surface hydroxyl groups with surface hydrogen was also identified. This mechanism is particularly important for high coverages of oxygen (0.5 ML) and low coverages of H₂S (0.15 ML), where water desorption was observed at 235 K, but was not observed spectroscopically at 110 K. The sequential addition of two surface hydrogen atoms to surface oxygen is not an important mechanism in this system.

These reactions were modeled using a bond-order conservation method, and the model successfully reproduced the important mechanistic conclusions.     

On the controversial magnetic properties of the schiff-base metal-organic polymer {[Fe(C13H17N3)2]SO4·6H2O}n

Within the search for magnetic ordering in organic and metal-organic compounds, the polymeric material of formula {[Fe(C₁₃H₁₇N₃)₂]SO₄·6H₂O}_n has been extensively studied by magnetic measurements. Our results show a basic agreement with the previous ones. Nevertheless, our study, including more data, leads to an interpretation in terms of superparamagnetism rather than metamagnetism as was previously reported.     

An XPS study of SO2 ON A CaO surface derived from Ca(OH)2

The adsorption of SO₂ on a CaO surface derived from Ca(OH)₂ has been studied by X-ray photoelectron Spectroscopy. It is shown that SO₂ adsorbs molecularly on the CaO surface forming SO₃²⁻ and SO₄²⁻. The adsorbate SO₃²⁻ species shift the Ca2p core levels about 2 eV toward higher binding energy. However, the formation of SO₄²⁻ species does not induce any further observable changes in the Ca core line spectra. These results are explained and discussed in terms of an electronic charge transfer from the substrate metal atoms to the adsorbed molecules and vice versa.     

第一性原理研究O2在TiN4掺杂石墨烯上的氢化

作为一种新型高效质子交换膜燃料电池阴极材料, 金属与N共掺杂的石墨烯因其对氧还原反应具有较高的活性而引起了人们的广泛关注. 采用包含色散力校正的密度泛函理论方法系统地研究了O₂在TiN₄掺杂的Graphene上的吸附, 氢化特性. 结果表明: 1) O₂倾向于以side-on模式吸附在Ti顶位, 形成O-Ti-O三元环结构; 2) O₂在TiN₄-Graphene上更倾向于以分子形式直接氢化, 形式OOH结构, 并进一步解离为O+OH, 反应的限速步为O₂的氢化, 对应的反应势垒为0.52 eV.     

The decomposition of H2S on Ni(110)

Adsorbed H₂S decomposes on Ni(110) to form primarily surface S and H for coverages of less than 0.5 ML. The hydrogen evolves in two separate TPD peaks, characteristic of hydrogen recombination and desorption from the clean surface and from regions perturbed by chemisorbed sulfur. XPS and HREELS indicate the presence of SH and possibly H₂S groups on the surface at 110 K. The XPS data indicates that for coverages less than about 0.5 ML, the concentration of molecular H₂S is small, but it is difficult to asess the coverage of SH groups. However, all of the molecular species decompose prior to hydrogen desorption (for high coverage, 180 K). Physisorbed H₂S is observed on the surface for coverages greater than about 0.5 ML.

The sulfur Auger lineshape was observed to be a function of both coverage and temperature. The changes in the lineshape were attributed to perturbations in local bonding interactions between the S and the Ni surface, perhaps involving some change in either bonding sites or distances but not involving SH bond scission.

The decomposition reaction was modeled using a bond order conservation method which successfully reproduced the experimental results.     

NMR study of monomethylammonium cation in (CH3NH3)5Bi2Cl11 ferroelectric polycrystal

Spin-lattice relaxation times T₁ and T_1ρ are determined for protons in three polycrystals (CH₃NH₃)₅Bi₂Cl₁₁, (CD₃NH₃)₅Bi₂Cl₁₁ and (CH₃ND₃)₅Bi₂Cl₁₁. The temperature dependencies of the relaxation times obtained for (CH₃NH₃)₅Bi₂Cl₁₁ and (CD₃NH₃)₅Bi₂Cl₁₁ are interpreted as a result of correlated motions of the three-proton groups of the monomethylammonium cation. The minimum of the T_1ρ relaxation time is explained as a result of the oscillations of the symmetry axis of the whole cation.     

Plasma chemical investigations for NOx andSO2 removal from flue gases

In a streamer-dominated pulsed corona the energetic electrons can interact with the background molecules and produce O, OH, and HO₂ radicals. Reactions involving these radicals are studied to analyze their effect on the removal of acidic pollutants NO, NO₂ , and SO₂ from flue gases. For the NO removal the reactions with O and HO₂ play a dominant role, whereas the OH radical is primarily responsible for the SO₂ and NO₂ removal     

Electrical conductivity and defect structure of Mg-doped Cr2O3

The electrical conductivity of Cr₂O₃ nominally doped with 2 mol% MgO has been studied by the four point a.c. technique as a function of the oxygen activity (O₂ + Ar, CO + CO₂ and H₂ + H₂O) in the temperature range 400–1200 °C. It is concluded that Cr₂O₃ doped with MgO is an extrinsic conductor and that the dissolved Mg-dopant is compensated by the formation of electron holes at near atmospheric oxygen pressures and by oxygen vacancies (or possibly interstitial chromium ions) at highly reduced oxygen activities (in CO + CO₂ and H₂ + H₂O gas mixtures). In H₂ + H₂O mixtures Mg-doped chromia also dissolves hydrogen as protons and significantly affects the defect structure and electrical conductivity. The defect structure of the oxide under various conditions is discussed.     

大气SO2柱总量遥感反演算法比较分析及验证

卫星遥感技术已成为城市污染气体SO₂监测和全球火山活动监测及预警的重要手段. 目前新的PCA (principal component analysis)算法有效减小了反演数据噪声, 并替代之前业务算法BRD (band residual difference)用于边界层SO₂柱总量产品的反演. 然而, 目前对PCA算法反演产品精度的评价和验证研究较少, 缺少与BRD算法产品进行长时间序列的比较以评估算法适用性, 尤其在中国大气污染重点城市区域. 本文利用地基多轴差分吸收光谱仪(MAX-DOAS)观测及多尺度空气质量模式系统(RAMS-CMAQ)大气化学模式模拟等数据, 评估PCA和BRD 反演算法的精度及误差. 另外, 选取洁净海洋地区、中国大气污染重点城市区域和高浓度火山喷发三种情况, 比较分析PCA 与BRD SO₂ 总量的时空格局变化差异及对不同SO₂总量下的适用性, 并对两种算法反演不确定性进行分析讨论. 结果表明, 在中国京津冀、珠江三角洲和长江三角洲区域, PCA SO₂总量反演值低于BRD, BRD反演结果更接近于地基的MAX-DOAS观测值, 冬季BRD和PCA SO₂总量值低于RAMS-CMAQ 模拟结果, 夏季7月和8月BRD SO₂总量值高于RAMS-CMAQ 模拟结果. 在SO₂总量接近于0 值的洁净海洋地区, PCA 算法产品噪声水平低于BRD算法, 但PCA 反演结果整体偏差大于BRD算法. 在高浓度火山喷发情况下, 当SO₂总量大于25 DU时BRD SO₂总量反演值低于PCA, 且随着SO₂ 总量增大, 两种算法反演值差异亦增大. 该研究对于OMI (Ozone Monitering Instrument) SO₂产品的应用具有重要的参考价值, 通过分析不同反演算法的差异及对其不确定性追因, 对于算法改进研究也具有重要的科学意义.     

用于白光LED的高亮度蓝白色荧光粉Ca2SiO3Cl2：Eu2+的发光性质

采用固相法在较低温度下合成了Eu²⁺激活的Ca₂SiO₃Cl₂高亮度蓝白色发光材料,并对其发光性质进行了研究。其发射光谱由两个谱带组成,峰值分别位于420,498nm处,归结为Ca₂SiO₃Cl₂晶体中占据两种不同Ca²⁺格位的Eu²⁺离子的5d→4f跃迁发射。改变Eu²⁺浓度,可以使样品的发光在蓝白色和绿白色之间变化。当Eu²⁺浓度为0.005mol^-1时,样品呈现很亮的蓝白色发光。两个发射峰的激发光谱均分布在250~410nm的波长范围内,峰值分别位于333,369nm处。Ca₂SiO₃Cl₂:Eu²⁺可被InGaN管芯产生的近紫外辐射有效激发,是一种性能良好的白光LED用单一基质蓝白色荧光粉。     

纳米纤维状Sr3Al2O5Cl2:Eu2+,Tm3+的白色长余辉性能

采用高温固相法在800℃下制备出系列白色长余辉荧光粉Sr₃Al₂O₅Cl₂：Eu²⁺,Tm³⁺,并研究了它们的结构、形貌及发光性能。样品Sr_2.91Al₂O₅Cl₂：0.04Eu²⁺,0.05 Tm³⁺具有单一晶相和纳米纤维结构。该样品在紫外光激发下表现出两个很强的宽带发射（分别位于~448 nm和~590 nm）。它的余辉寿命大约是20 min。利用此种荧光粉所制作出的白光LED器件表现出很强的白光发射。