Conductivity study of some polymer electrolytes based on polyacrylonitrile

The present paper deals with the room temperature conductivity study of some polymer electrolytes based on polyacrylonitrile, ammonium tetraflouroborate as dopant, and propylene carbonate (PC) and polyethylene glycols (PEG300 and PEG600) as plasticizers. The additions of plasticizers having different dielectric constant have been found to modify the conductivity of polymer electrolytes. The increase in room temperature conductivity with plasticizer addition has been found to depend upon (1) the amount of salt present and (2) amount of plasticizers added. The polymer electrolytes prepared were characterized by X-ray diffraction, scanning electron micrographs, infrared, thermogravimetric, and AC impedance measurements. The highest room temperature conductivity observed in case of these polymer electrolytes was ∼10–13 s/cm.     

Effect of donor number of solvent on the conductivity behaviour of nonaqueous proton-conducting polymer gel electrolytes

The effect of donor number of solvent on the conductivity behaviour of gel electrolytes has been studied. Liquid electrolytes were prepared by dissolving salicylic acid in solvents based on ethylene carbonate (EC), propylene carbonate (PC) and dimethylformamide (DMF) with different donor number and dielectric constant values. Three different polymers, polymethylmethacrylate (PMMA), polyacrylonitrile (PAN) and polyethylene oxide (PEO), were used as the gelling polymer. The conductivity of polymer gel electrolytes has been found to be higher than the corresponding liquid electrolytes, i.e. σ (gel)>σ (liquid). This has been explained to be due to an increase in carrier concentration by the dissociation of undissociated salicylic acid/ion aggregates present in the electrolytes with the addition of polymer. However, the relative increase in conductivity observed with the addition of different gelling polymers has been found to depend upon the donor number of the solvent used.     

Effect of plasticizer on ionic transport and dielectric properties of PVA-H3PO4 proton conducting polymeric electrolytes

Solid polymer electrolytes have attracted considerable attention due to their wide variety of electrochemical device applications. The present paper is focused on the effect of plasticizer to study the structural, electrical and dielectric properties of PVA-H₃PO₄ complex polymer electrolytes. XRD results show that the crystallinity decreases due to addition of plasticizer up to particular amount of polyethylene glycol (PEG) and thereafter it increases. Consequently, there is an enhancement in the amorphicity of the samples responsible for process of ion transport. This characteristic behavior can be verified by the analysis of the differential scanning calorimetry results. FTIR spectroscopy has been used to characterize the structure of polymer and confirms the complexation of plasticizer with host polymeric matrix. Electrical and dielectric properties have been studied for different wt% of plasticizer and their variations have been observed. The addition of PEG has significantly improved the ionic conductivity. The optimum ionic conductivity value of the plasticized polymer electrolyte film of 30 wt% PEG has been achieved to be of the order of 10⁻⁴ S cm⁻¹ at room temperature and corresponding ionic transference number is 0.98. The minimum activation energy is found to be 0.25 eV for optimum conductivity condition.     

Evidence of ion pair breaking by dispersed polymer in polymer gel electrolytes

Non-aqueous polymer gel electrolytes containing trifluoromethanesulfonic acid (HCF₃SO₃) and polyethylene oxide (PEO) as the gelling polymer has been studied. The increase in conductivity observed with the addition of PEO to liquid electrolytes has been explained to be due to the breaking of ion aggregates present in electrolytes at higher acid concentrations. The increase in free H⁺ ion concentration upon breaking of ion aggregates has also been observed in pH measurements and viscosity of gel electrolytes has been found to increase with PEO addition. Polymer gel electrolytes containing dimethylacetamide (DMA) have σ ∼ 10⁻² S/cm at room temperature and are stable over −50 to 125 °C range of temperature. Gels based on propylene carbonate (PC) and ethylene carbonate (EC) are stable in the −50 to 40 °C temperature range and loose their gelling nature above 40 °C.     

Evidence of ion pair breaking by dispersed polymer in polymer gel electrolytes

Non-aqueous polymer gel electrolytes containing trifluoromethanesulfonic acid (HCF₃SO₃) and polyethylene oxide (PEO) as the gelling polymer has been studied. The increase in conductivity observed with the addition of PEO to liquid electrolytes has been explained to be due to the breaking of ion aggregates present in electrolytes at higher acid concentrations. The increase in free H⁺ ion concentration upon breaking of ion aggregates has also been observed in pH measurements and viscosity of gel electrolytes has been found to increase with PEO addition. Polymer gel electrolytes containing dimethylacetamide (DMA) have σ ∼ 10⁻² S/cm at room temperature and are stable over −50 to 125 °C range of temperature. Gels based on propylene carbonate (PC) and ethylene carbonate (EC) are stable in the −50 to 40 °C temperature range and loose their gelling nature above 40 °C.     

Lithium ion conductivity and dielectric properties of P(VdCl-co-AN-co-MMA)-LiCl-EC triblock co-polymer electrolytes

Lithium ion conducting polymer electrolytes based on triblock polymer P(VdCl-co-AN-co-MMA)–LiCl were prepared using a solution casting technique. XRD studies show that the amorphous nature of the polymer electrolyte has been increased due to the addition of LiCl. The maximum amorphous nature has been observed for 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl samples. The FTIR study of the lithium ion conducting polymer membrane confirms the complex formation between the polymer P(VdCl-co-AN-co-MMA) and LiCl. The lithium ion conductivity is found to be 1.6 × 10^?5 Scm^?1 for the 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl sample at room temperature. This value is found to be greater than that of pure polymer whose conductivity is found to be 1.5 × 10^?8 Scm^?1. To improve ionic conductivity, ethylene carbonate has been added as a plasticizer to the 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl sample. When we add 0.6 m% of ethylene carbonate, it has been observed that the lithium ion conductivity has increased to 1.3 × 10^?3 Scm ^?1 . This value is two orders of magnitude greater than the 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl sample. It is also observed from XRD patterns of 40 m% P(VdCl-co-AN-co-MMA)/60 m % LiCl/0.6 m % EC that the amorphous nature has been increased further. A dielectric study has been performed for the above membranes.     

Effects of gamma radiation treatment and plasticizer on alkaline solid polymer electrolytes

Alkaline solid polymer electrolyte films have been prepared by the solvent-casting method. Gamma radiation treatment and propylene carbonate plastisizer were used to improve the ionic conductivity of the electrolytes at ambient temperature. The structure of the irradiated electrolytes changes from semi-crystalline to amorphous, indicating that the crosslinking of the polymer has been achieved at a dose of 200 kGy. The ionic conductivity at room temperature of PVA/KOH blend increases from 10⁻⁷ to 10⁻³ Scm⁻¹ after the PVA crosslinking and when the plasticizer concentration was increased from 20 to 30%. Paper presented at the International Conference on Functional Materials and Devices 2005, Kuala Lumpur, Malaysia, June 6 – 8, 2005.     

Physicochemical studies of PVdF–HFP-based polymer–ionic liquid composite electrolytes

Polymer–ionic liquid composite electrolytes based on poly (vinylidenefluoride-co-hexafluoropropylene) (PVdF–HFP) and room temperature ionic liquid: 2,3-dimethyl-1-octylimidazolium hexafluorophosphate (DMOImPF₆) have been synthesized and studied. The addition of dimethylacetamide (DMA) and propylene carbonate (PC), both with high dielectric constant and low viscosity, to polymer electrolytes has been found to result in an enhancement of conductivity by one order of magnitude. Composite polymer electrolytes containing ionic liquid have been found to be thermally stable upto 300°C. Motional narrowing observed in the variation of line width of ¹H and ¹⁹F NMR peaks with temperature suggests that both cations and anions are mobile in these electrolytes.     

Conductivity studies on PEO:NaClO3 electrolyte system with different plasticizers

A new ion conducting solid polymer electrolyte thin film based on Polyethylene oxide (PEO) with NaClO₃ salt is prepared by solution-casting method. The solvation of salt with PEO has been confirmed by X-ray diffraction and IR spectral studies. Plasticizer effects were studied in PEO:NaClO₃ system by using low molecular weight polyethylene glycol (PEG), dimethyl formamide (DMF) and propylene carbonate(PC). AC conductivity in the temperature range (308–378 K) was measured to evaluate the conductivity of the polymer electrolytes. From the conductivity data, it was found that the conductivity value of pure PEO increases 10²–10⁴ order of magnitude with the addition of salts as well as plasticizers. From the transference number experiments, it was confirmed that the charge transport in these electrolyte is mainly due to the ions (t_ion≈0.94). Finally, the conductivity value of all PEO: NaClO₃ systems were compared.     

Effects of MnO<Subscript>2</Subscript> nano-particles on the conductivity of PMMA-PEO-LiClO<Subscript>4</Subscript>-EC polymer electrolytes

Li-ion rechargeable batteries based on polymer electrolytes are of great interest for solid state electrochemical devices nowadays. Many studies have been carried out to improve the ionic conductivity of polymer electrolytes, which include polymer blending, incorporating plasticizers and filler additives in the electrolyte systems. This paper describes the effects of incorporating nano-sized MnO₂ filler on the ionic conductivity enhancement of a plasticized polymer blend PMMA–PEO–LiClO₄–EC electrolyte system. The maximum conductivity achieved is within the range of 10⁻³ S cm⁻¹ by optimizing the composition of the polymers, salts, plasticizer, and filler. The temperature dependence of the polymer conductivity obeys the VTF relationship. DSC and XRD studies are carried out to clarify the complex formation between the polymers, salts, and plasticizer.     

Effect of dibutyl phthalate as plasticizer on high-molecular weight poly(vinyl chloride)–lithium tetraborate-based solid polymer electrolytes

A series of different composition of polymer electrolytes-based on poly(vinyl chloride) (PVC) as host polymer, lithium tetraborate (Li₂B₄O₇) as dopant salt, and dibutyl phthalate (DBP) as plasticizer were prepared by solution casting method. The interaction between the PVC, Li₂B₄O₇, and DBP were studied by Fourier transform infrared. The shifting, broadening, and splitting of transmission peaks were the evidences of complexation. The highest ionic conductivity polymer electrolyte of 2.83 × 10⁻⁶ S/cm was achieved at ambient temperature upon addition of 30 wt.% of DBP. In addition, the temperature-dependent conductivity, frequency-dependent conductivity, dielectric permittivity, and modulus studies were performed. The temperature-dependent conductivity of the polymer electrolytes was found to obey the Arrhenius behavior. The thermal stability of polymer electrolytes was verified by thermogravimetric analysis. The lower in glass transition temperature was proven in differential scanning calorimetry, whereas the higher amorphous region within the polymer matrix was demonstrated in X-ray diffraction.     

Structural and ionic conductivity studies on P(ECH-EO):γ-BL:LiClO<Subscript>4</Subscript> plasticized polymer electrolyte

The plasticized polymer electrolyte consisting of poly(epichlorohydrin-ethyleneoxide) [P(ECH-EO)], lithium perchlorate (LiClO₄) and γ-butyrolactone (γ-BL) have been prepared by simple solution casting technique. The polymer–salt–plasticizer complex has been confirmed by XRD analysis. The ionic conductivity studies have been carried out using AC impedance technique. The effect of plasticizer (γ-BL) on ionic conductivity has been discussed with respect to different temperatures. The maximum value of ionic conductivity is found to be 1.3 × 10⁻⁴ Scm⁻¹ for 70P(ECH-EO):15γ-BL:15LiClO₄ at 303 K. The temperature dependence of the plasticized polymer electrolyte follows the Vogel–Tamman–Fulcher formalism. The activation energy is found to decrease with the increase in plasticizer.     

Effects of plasticizer and nanofiller on the dielectric dispersion and relaxation behaviour of polymer blend based solid polymer electrolytes

Solid polymer electrolytes consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend (50:50 wt/wt%) with lithium triflate (LiCF₃SO₃) as a dopant ionic salt at stoichiometric ratio [EO + (CO)]:Li⁺ = 9:1, poly(ethylene glycol) (PEG) as plasticizer (10 wt%) and montmorillonite (MMT) clay as nanofiller (3 wt%) have been prepared by solution cast followed by melt–pressing method. The X–ray diffraction study infers that the (PEO–PMMA)–LiCF₃SO₃ electrolyte is predominantly amorphous, but (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG electrolyte has some PEO crystalline cluster, whereas (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG–3 wt% MMT electrolyte is an amorphous with intercalated and exfoliated MMT structures. The complex dielectric function, ac electrical conductivity, electric modulus and impedance spectra of these electrolytes have been investigated over the frequency range 20 Hz to 1 MHz. These spectra have been analysed in terms of the contribution of electrode polarization phenomenon in the low frequency region and the dynamics of cations coordinated polymer chain segments in the high frequency region, and also their variation on the addition of PEG and MMT in the electrolytes. The temperature dependent dc ionic conductivity, dielectric relaxation time and dielectric strength of the plasticized nanocomposite electrolyte obey the Arrhenius behaviour. The mechanism of ions transportation and the dependence of ionic conductivity on the segmental motion of polymer chain, dielectric strength, and amorphicity of these electrolytes have been explored. The room temperature ionic conductivity values of the electrolytes are found ∼10⁻⁵ S cm⁻¹, confirming their use in preparation of all-solid-state ion conducting devices.     

Li ion conduction on plasticizer-added PVAc-based hybrid polymer electrolytes

Poly(vinyl acetate), poly(vinylidene fluoride–hexafluoropropylene), lithium perchlorate salt, and the different plasticizer-based gel polymer electrolytes were prepared by solvent-casting technique. The structural and the complex formation have been confirmed by X-ray diffraction spectroscopic analysis. Thermal stability of the different plasticizer-added electrolyte films has been analyzed by means of thermogravimetric analysis. Ionic conductivity of the electrolyte samples has been found as a function of temperature and the plasticizers. Among the various plasticizers, ethylene carbonate-based complexes exhibit maximum ionic conductivity value of the order of 10⁻⁴ Scm⁻¹. Finally, the microstructure of the maximum ionic conductivity sample has been depicted with the help of scanning electron microscope analysis.     

Electrical characterization of nano-composite polymer gel electrolytes containing NH4BF4 and SiO2: role of donor number of solvent and fumed silica

Nano-composite polymer gel electrolytes were synthesized by using polyethylene oxide (PEO), ammonium tetrafluoroborate (NH₄BF₄), fumed silica (SiO₂), dimethylacetamide (DMA), ethylene carbonate (EC), and propylene carbonate (PC) and characterized by conductivity studies. The effect of donor number of solvent on ionic conductivity of polymer gel electrolytes has been studied. The mechanical strength of the gel electrolytes has been increased with the addition of nano-sized fumed silica along with an enhancement in conductivity. Maximum room temperature ionic conductivity of 2.63 × 10⁻³ and 2.92 × 10⁻³ S/cm has been observed for nano-composite gel electrolytes containing 0.1 and 0.5 wt% SiO₂ in DMA+1 M NH₄BF₄+10 wt% PEO, respectively. Nano-composite polymer gel electrolytes having DMA have been found to be thermally and electrically stable over 0 to 90 °C temperature range. Also, the change in conductivity with the passage of time is very small, which may be desirable to make applicable for various smart devices.

     

Development and characterizations of PVdF-PEMA gel polymer electrolytes

A new class of gel polymer electrolytes comprising the blend of poly(ethyl methacrylate) (PEMA) and poly(vinylidene fluoride), the mixture of ethylene carbonate and propylene carbonate as a plasticizer, and lithium perchlorate (LiClO₄) as a salt was prepared using solvent casting technique. The formation of polymer–salt complexes has been confirmed by XRD analysis. Morphological and thermal studies have been performed using SEM and DMA analyses. A comparative look between PEMA and poly(methyl methacrylate) (PMMA) electrolytes has showed that PEMA electrolytes exhibited better electrochemical performances than PMMA electrolytes, despites its lower conductivity.     

Effect of radiation on conductivity of solid PVA–KOH–PC composite polymer electrolytes

The aim of this work is to enhance the room temperature conductivity of solid alkaline composite polymer electrolytes (ACPEs) based on polyvinyl alcohol/potassium hydroxide/propylene carbonate (PVA–KOH–PC) composites by cross-linking the PVA and bond scission of the PC by γ-radiation. The ACPEs were prepared by solvent-casting technique and irradiated with doses up to 200 kGy at room temperature. The microstructure of the ACPEs was measured using XRD spectrometer, and the results show the structural change from semicrystalline to amorphous, indicating that the cross-linking has been achieved at higher doses. It was found that the PKOH composite at 40 wt% KOH and PPC composite at 60 wt% PC show higher conductivities. The conductivity of the PKPC composites is dominated by dc conductivity at higher frequencies and that PC with 60 wt% has the highest conductivity at a dose of 200 kGy.Paper presented at the International Conference on Functional Materials and Devices 2005, Kuala Lumpur, Malaysia, June 6–8, 2005.     

Influence of plasticizer on ionic conductivity of PVC-PBMA polymer electrolytes

Plasticized polymer electrolytes comprising of ethylene carbonate as the plasticizing agent in poly (vinyl chloride) [PVC]–poly (butyl methacrylate) [PBMA] blended polymer electrolytes were prepared by solution casting technique. Complex formation, structural elucidation, conductivity, dielectric parameters (?′, ?″, M′, and M″), thermal stability, and surface morphology are brought out from FTIR, XRD, ac impedance analysis, dielectric studies, thermogravimetry/differential thermal analysis, and scanning electron microscopic studies, respectively. Polymer electrolytes are found to exhibit higher ionic conductivity at higher concentration of plasticizer at the cost of their mechanical stability. Conductivity of 1.879 × 10^?4 S cm^?1 is exhibited by the polymer electrolyte consisting of 69% of plasticizer with appreciable thermal stability up to 523 K. Temperature and frequency dependence of conductivity is found to follow Vogel Tammann Fulcher relation and Jonscher power law, respectively. Real and imaginary parts of dielectric constants are found to decrease with increase in frequency which could be due to the electrode polarization effect.     

Rheological properties and impedance spectroscopy of PMMA-PVdF blend and PMMA gel polymer electrolytes for advanced lithium batteries

In the present study, blend ionic conducting membranes formed by poly(methylmethacrylate (PMMA) / poly(vinilydenefluoride) (PVDF) (blend ratio PMMA/PVdF=80/20), lithium perchlorate (LiClO₄) as a salt and a mixture of ethylene carbonate (EC)-propylene carbonate (PC) as plasticizer are prepared and characterized by impedance spectroscopy and dynamic rheological experiments. We compared the results obtained on the blends with those on PMMA gel-based polymer electrolytes incorporating the same EC/PC mixture of plasticizer and the same quantities of salt. The main focus of this study is to illustrate the rheological data of the gels and blends electrolytes to point up their mechanical stability with the temperature in sight of the technological application. The conductivity values are reported in the 20–100 °C temperature range for different lithium salt contents, while the rheological behaviour has been recorded up to 140 °C. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Conductivity studies of plasticized PEO–HPF6–fumed silica nanocomposite polymer electrolyte system

The effect of the addition of propylene carbonate (PC) on the ion transport behaviour of nanocomposite polymer electrolytes having composition of polyethylene oxide?Chexafluorophosphoric acid?Cfumed silica has been studied. The ionic conductivity of 6.89?×?10^?4 S cm^?1 at 298?K has been obtained for these electrolytes along with good mechanical and thermal properties. The variation of ¹H NMR linewidth with temperature shows line narrowing at the glass transition and melting temperature of the electrolytes which suggests the onset of long-range ion translational motion. The increase in ionic conductivity with the addition of PC is related to the transformation of these electrolytes to the amorphous phase which has been supported by X-ray diffraction results. The polymer electrolytes are thermally stable up to around 498?K and hence are suitable for various applications.