Ex Situ Prepared Antimony Film Electrode for Electrochemical Stripping Measurement of Heavy Metal Ions

The antimony film electrode (SbFE) was prepared ex situ for anodic and adsorptive stripping voltammetric measurement of selected heavy metal ions. The electrode revealed good linearity for Cd(II) and Pb(II) in a nondeaerated solution of 0.01 M HCl in the examined concentration range from 25 to 80 μg L^?1 with limits of detection of 1.1 μg L^?1 for Cd(II) and 0.3 μg L^?1 for Pb(II) and an excellent reproducibility. The preplated SbFE was also preliminary tested for measuring low levels of Ni(II) using adsorptive stripping voltammetry exhibiting good linearity and sensitivity in combination with only a 30 s deposition step.     

AgNP/Bi/Nafion‐modified Disposable Electrodes for Sensitive Zn(II), Cd(II), and Pb(II) Detection in Aerosol Samples

A new method for modifying electrodes with Ag nanoparticles (AgNPs) using electrospray deposition for sensitive, selective detection of Zn(II), Cd(II), and Pb(II) in aerosol samples when combined with Bismuth and Nafion coating and square‐wave anodic stripping voltammetry (SWASV) is reported. Carbon stencil‐printed electrodes (CSPEs) fabricated on a polyethylene transparency (PET) sheet were produced for an inexpensive, simple to fabricate, disposable sensor that can be used with the microliter sample volumes for analysis. Sensor performance was improved by modifying the electrode surface with electrospray‐deposited AgNPs. The use of electrospray deposition resulted in more uniform particle dispersion across the electrode surface when compared to drop‐casting. Using AgNP‐modified electrodes combined with Bi and Nafion, experimental detection limits (LODs) of 5.0, 0.5, and 0.1 μg L⁻¹ for Zn(II), Cd(II), and Pb(II), respectively, were achieved. The linear working ranges were 5.0–400.0 μg L⁻¹, 0.5–400.0 μg L⁻¹, and 0.1–500.0 μg L⁻¹ for Zn(II), Cd(II), and Pb(II), respectively. Interference studies showed Cu(II) was the only metal that interfered with this assay but inference could be eliminated with the addition of ferricyanide directly to the sample solution. This electrochemical sensor was applied for the simultaneous determination of Zn(II), Cd(II), and Pb(II) within source particulate matter (PM) samples collected on filters using an aerosol test chamber.     

The Fabrication and Characterization of a Bismuth Nanoparticle Modified Boron Doped Diamond Electrode and Its Application to the Simultaneous Determination of Cadmium(II) And Lead(II)

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by square‐wave anodic stripping voltammetry (SWASV) using a bismuth nanoparticle modified boron doped diamond (Bi‐BDD) electrode. Bi deposition was performed in situ with the analytes, from a solution of 0.1 mM Bi(NO₃)₃ in 0.1 M HClO₄ (pH 1.2), and gave detection limits of 1.9 μg L^?1 and 2.3 μg L^?1 for Pb(II) and Cd(II) respectively. Pb²⁺ and Cd²⁺ could not be detected simultaneously at a bare BDD electrode, whilst on a bulk Bi macro electrode (BiBE) the limits of detection for the simultaneous determination of Pb²⁺ and Cd²⁺ were ca. ten times higher.     

Preparation of an ion-selective electrode by chemical treatment of copper wire for the measurement of copper(II) and iodide by batch and flow-injection potentiometry

The preparation of an ion-selective electrode by chemical treatment of copper wire and its application for the measurements of copper (II) and iodide ions is described. The proposed reaction mechanism at the sensing surface, which explains the response of the electrode to Cu²⁺ and iodide ions, is discussed. The prepared electrode was suitable for direct potentiometric measurements of iodide and copper (II) in batch experiments down to concentrations of 1 × 10^–5 mol L^–1. A tubular electrode, prepared in the same way, may be used as a potentiometric sensor in a flow-injection analysis for Cu (II) and/or iodide determinations.     

Preconcentration of palladium(II) from water with thionalide loaded on silica gel

2-Mercapto-N-2-naphthylacetamide (thionalide) on silica gel is used for rapid preconcentration of μg l^?1 levels of palladium(II) from aqueous solution, followed by atomic absorption spectrometric measurement. In batch experiments, palladium was quantitatively retained on the gel from solutions 5 M in acid to pH 8; equilibrium was achieved within 10 s. The chelating capacity of the gel was 7.5 μmol Pd g^?1 at pH < 4. The effect of flow rate on retention was studied. Palladium retained on the column was completely eluted with 20 ml of 0.2 M thiourea in 0.1 M hydrochloric acid. The palladium concentration in sea water is shown to be < 0.3 μg l^?1.     

Differential Pulse Anodic Stripping Voltammetric Determination of Lead (II) Using Poly Xylenol Orange Modified Electrode

In this work a method for sensitive anodic stripping voltammetric determination of Pb(II) ions using a poly xylenol orange film modified electrode (PXOFME) has been proposed. Poly xylenol orange film (PXOF) was formed on a paraffin impegrenated graphite electrode (PIGE) using electro polymerization method by scanning the potential between −0.5 V to 1.3 V, at a scan rate of 50 mV/s for 30 segments in 0.1 M phosphate buffer solution (PBS) of pH 7. The PXOFME was characterized by scanning electron microscopy (SEM), ATR‐IR spectroscopy, cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The modified electrode has been used to develop a sensitive method for the determination of Pb(II) ions by anodic stripping voltmmetry (ASV). The PXOFME was used to preconcentrate Pb(II) ions through complexation, the complexed metal ions were reduced electrochemically and then stripped anodically from the surface of the electrode. A linear range of 5 μg/L to 413 μg/L with a limit of detection (S/N=3) of 1.6 μg/L was observed for the determination of Pb(II) ions. The method was applied to lead determination in sea water and tap water samples and the results were found to be satisfactory.     

A Prospect for the Analysis of Species Acting as Enzyme Inhibitors as Illustrated by Heavy Metal Inhibition

Abstract

A flow system incorporating an amperometric glucose oxidase enzyme electrode has been used to study the inhibitory effects of 16 metal cations on glucose oxidase. Only copper(II), mercury(II) and silver(I) caused any significant inhibition. the enzyme electrode could be reactivated by EDTA, the reactivation being most effective for copper(II) and least so for silver(I). Other complexing agents were tried for reactivation but proved to be unsatisfactory.

The ability to reactivate the enzyme on the electrode following copper(II) inhibition, and the linear response of the system to the level of this inhibitor according to I/A = -9.49 × 10^?7 log([Cu]/M) + 4.84 × 10^?8; r = 0.994 between 2.5 × 10^?4M and 5 × 10^?3M [Cu]²⁺ indicates a prospect for the use of a flow system for determining enzyme inhibitors in samples.     

Selective Electrochemical Analysis of Various Metal Ions at an EDTA Bonded Conducting Polymer Modified Electrode

An EDTA‐bonded conducting polymer modified electrode was prepared and characterized by FT‐IR. The modified electrode was used for the selective electrochemical analysis of various trace metal ions such as, Cu(II), Hg(II), Pb(II), Co(II), Ni(II), Fe(II), Cd(II), and Zn(II) at the different pHs by linear sweep and square wave voltammetry. Dynamic ranges were obtained using square wave voltammetry from 0.1 μM to 10.0 μM for Co(II), Ni(II), Cd(II), Fe(II), and Zn(II) and 0.5 nM to 20 nM for Cu(II), Hg(II), and Pb(II) after 10 min of preconcentration. The detection limits were determined to be 0.1 nM, 0.3 nM, 0.4 nM, 50.0 nM, 60.0 nM, 65.0 nM, 80.0 nM, and 90.0 nM for Cu(II), Hg(II), Pb(II), Co(II), Ni(II), Cd(II), Fe(II), and Zn(II), respectively. The technique offers an excellent way for the selective trace determination of various heavy metal ions in a solution.     

Voltammetric Detection of Captopril Using Copper(II) and an Unmodified Glassy Carbon Electrode

We report a simple, sensitive, and rapid detection of captopril using copper(II) and a bare glassy carbon electrode with cyclic voltammetry. The captopril is detected by the formation of a copper(II)‐captopril complex that is observed to have a characteristic oxidation potential at+0.24 V vs. Ag/AgCl. It is found that the peak current varies linearly with the concentration of captopril. The linear dynamic range is obtained for a captopril concentration of 1 µM to 10 µM, and the sensitivity is found to be 0.10±0.003 μA μM^?1. Importantly, the low limit of detection (n=3) of 0.10 μM and the precision of 3.2 %, are achieved using a simple, unmodified electrode. This is attributable to in situ adsorption of a copper(II)‐captopril complex on the electrode surface.     

Carbon Paste Electrode Plated with Lead Film. Voltammetric Characteristics and Application in Adsorptive Stripping Voltammetry

A lead film plated in situ at a carbon paste support was tested as a novel, potential electrode for adsorptive stripping voltammetric determination of cobalt traces in an ammonia buffer solution. To show the practical applicability of the new electrode, a catalytic adsorptive Co system in a supporting electrolyte containing 0.1 M ammonia buffer, 5×10^?4 M nioxime and 0.25 M nitrite was selected and investigated as a model solution. Pb and Co ions were simultaneously accumulated in situ on the electrode surface: Pb ions electrochemically at ?1.3 V) and then at ?0.75 V, at which potential the Co(II)‐nioximate complex was also pre‐concentrated via adsorption. Instrumental parameters, such as the time of nucleation and formation of Pb film deposits, the time of accumulation of the Co‐nioxime complex at the PbF/CPE, and the procedures of electrode regeneration, were optimized to obtain good reproducibility and sensitivity of the Co response. The optimized procedure yields favorable and highly stable stripping responses with good precision (RSD=3% for a 5×10^?8 M Co) and good linearity (up to 5×10^?7 M, coefficient of determination, R=0.996). The detection limit was 4×10^?10 M Co (0.023 μg L^?1) for an accumulation time of 120 s. The method enables the determination of Co in the presence of high excesses of Ni or Zn. The voltammetric data were correlated with the structural characterization by scanning electron microscopy (SEM) and X‐ray fluorescence spectroscopy (XRF).     

Preconcentration of copper,lead, cadmium and zinc ions from water with 2-mercaptobenzothiazole loaded on glass beads with the aid of collodion

2-Mercaptobenzothiazole (MBT) loaded on glass beads with the aid of collodion was prepared and used for selective preconcentration of μg l^?1 levels of copper(II) and lead from aqueous solutions. Copper and lead were quantitatively retained on the loaded beads from solutions of pH 5.0–6.0 and >5.0, respectively, while cadmium(II) and zinc(II) were retained at ? pH 6.0 and 7.0, respectively. The retention capacity of the loaded beads was ca. 108 μg Cu g^?1 (1.7 μmol g^?1) at pH 5.5 for beads of 0.3–0.4 mm diameter. The mole ratios of MBT to copper(II) and lead(II) were ca. 10 and 45, respectively, regardless of the amount of MBT loaded on the beads. Copper was completely retained on the column at a high flow rate (21.7 ml min^? cm^?2) and lead(II) at up to 12.7 ml min^? cm^?2. Cadmium(II) and zinc(II) were not retained quantitatively even at low flow rates (< 1.2 ml min^?1 cm^?2). Thus, selective preconcentration of copper and lead was achieved by passing the sample through the column at high flow rate at pH 6.5. The copper and lead retained on the column were complete eluted together with the collodion with 5 ml of MIBK by batch-mode elution, and determined directly by one-drop atomic absorption spectrometry. Copper(II) and lead(II) in several kinds of water were determined.     

Trace Analysis of Lead and Copper Ions in Fish Tissue Using Paste Electrodes

Abstract

DNA was immobilized onto a carbon nanotube surface through cyclic voltammetry, in which paste electrode (PE) was subjected to lead and copper trace ion analysis. Optimized conditions for square‐wave stripping voltammetry were then searched. The results indicated three other linear working ranges—3–21 mg l^?1, 2–16 µg l^?1, and 3–17 ng l^?1 Pb(II) Cu(II)—within an accumulation time of 190 s in 0.1‐M ammonium phosphate electrolyte solutions of pH 10.0. At the optimized conditions, the detection limit (S/N) was pegged at 0.4 ng l^?1 (1.93×10^?12 M Pb(II) and 6.29×10^?12 M Cu(II)). And the relative standard deviation at 10 mg l^?1 Pb(II) and Cu(II) was a 0.074 and 0.069% precision, in 15 measurements. The method can be applied to assays of fish tissue.     

Simultaneous determination of mercury(II), copper(II) and bismuth(III) in urine by flow constant-current stripping analysis with a gold fibre electrode

Urine samples are treated with concentrated nitric acid and potassium permanganate ar 70°C for 10 min prior to injection. The flow electrode system consists of a 10-μm diameter gold fibre working electrode, a glassy carbon reference electrode and a platinum counter electrode. In the fully automated constant-current stripping procedure, the gold fibre is first covered with a fresh gold film after which the sample is electrolyzed for 1 min prior to stripping in 0.1 M hydrochloric acid with a current of 0.1μA. The procedure is repeated on a spiked sample after which the sample analyte concentrations are evaluated and presented digitally and graphically on a printer/plotter. The results obtained for bismuth, copper and mercury in a urine reference sample were 36.9, 39.7 and 47.7 μg l^?1 with standard deviations (n=10) of 3.2, 4.2 and 2.1, respectively. The certified values for copper and mercury were 45 and 51 μg l^?1; no certified value was available for bismuth.     

Preparation of an ion-selective electrode by chemical treatment of copper wire for the measurement of copper(II) and iodide by batch and flow-injection potentiometry

The preparation of an ion-selective electrode by chemical treatment of copper wire and its application for the measurements of copper (II) and iodide ions is described. The proposed reaction mechanism at the sensing surface, which explains the response of the electrode to Cu²⁺ and iodide ions, is discussed. The prepared electrode was suitable for direct potentiometric measurements of iodide and copper (II) in batch experiments down to concentrations of 1 × 10^–5 mol L^–1. A tubular electrode, prepared in the same way, may be used as a potentiometric sensor in a flow-injection analysis for Cu (II) and/or iodide determinations. Received: 4 December 1998 / Revised: 31 March 1999 / Accepted: 6 April 1999     

Determination of Copper in the Presence of Various Amounts of Arsenic with L‐Cysteine Modified Gold Electrodes

An L ‐cysteine modified gold electrode for the determination of copper in the presence of various amounts of arsenic with anodic stripping voltammetry has been studied. The electrode was fabricated by immersing a gold electrode in an ethanol solution of 5mM L ‐cysteine for 60 min. Various parameters, such as the effect of different supporting electrolytes, the pH of the electrolyte and the deposition potential were investigated. Under optimum conditions, copper was accumulated at ?0.3 V (vs. SEC) for 60 s in 0.1 M phosphate buffer pH 5.0 in the presence of different amounts of arsenic. Essentially the same sensitivities (0.33±0.001 μA/μM) and limits of detection (0.13±0.002 μM) of copper were obtained with various amount of arsenic in the range 2 μM to 20 μM.     

A copper ion-selective electrode with high selectivity prepared by sol-gel and coated wire techniques

A sol-gel electrode and a coated wire ion-selective poly(vinyl chloride) membrane, based on thiosemicarbazone as a neutral carrier, were successfully developed for the detection of Cu (II) in aqueous solutions. The sol-gel electrode and coated electrode exhibited linear response with Nernstian slopes of 29.2 and 28.1 mV per decade respectively, within the copper ion concentration ranges 1.0×10^–5–1.0×10^–1 M and 6.0×10^–6–1.0×10^–1 M for coated and sol-gel sensors. The coated and sol-gel electrodes show detection limits of 3.0×10^–6 and 6.0×10^–6 M respectively. The electrodes exhibited good selectivities for a number of alkali, alkaline earth, transition and heavy metal ions. The proposed electrodes have response times ranging from 10–50 s to achieve a 95% steady potential for Cu²⁺ concentration. The electrodes are suitable for use in aqueous solutions over a wide pH range (4–7.5). Applications of these electrodes for the determination of copper in real samples, and as an indicator electrode for potentiometric titration of Cu²⁺ ion using EDTA, are reported. The lifetimes of the electrodes were tested over a period of six months to investigate their stability. No significant change in the performance of the sol-gel electrode was observed over this period, but after two months the coated wire copper-selective electrode exhibited a gradual decrease in the slope. The selectivity of the sol-gel electrode was found to be better than that of the coated wire copper-selective electrode. Based on these results, a novel sol-gel copper-selective electrode is proposed for the determination of copper, and applied to real sample assays.     

A Simple and Sensitive Method for the Detection of Trace Pb(II) and Cd(II) based on Nafion‐coated Antimony Film Electrode

Nafion‐coated antimony film electrode (NCAFE) was prepared in situ by simultaneously plated antimony with analytes, and applied to the determination of trace Pb(II) and Cd(II) in non‐deaerated solutions by differential pulse anodic stripping voltammetry (DPASV). Various experimental parameters, which influenced the response of the NCAFE to those metals, were thoroughly optimized and discussed. The results indicated that the sensitivity and resistance to surfactants at the NCAFE were remarkably improved with relative to the antimony film electrode (AFE). In the presence of 5 mg·L^?1 gelatin, the peak heights at the NCAFE showed 4‐fold enhancement for Pb and a 9‐fold enhancement for Cd over a bare AFE. Reproducibility of the sensor was satisfactory, and the relative standard deviations were 4.8% for 20 μg·L^?1 Pb and 3.2% for 25 μg·L^?1 Cd (n=15) with preconcentration time of 180 s. The determination limits (S/N=3) of this sensor were determined to be 0.15 μg·L^?1 for Pb and 0.30 μg·L^?1 for Cd with accumulation time of 300 s. The NCAFE was successfully applied to determining Pb(II) and Cd(II) in vegetable and water samples with satisfactory results.     

Coulometric determination of lead(II) and lead(IV) in high-T c superconductors containing copper and bismuth

The behavior of Pb(II) and Pb(IV) was studied by voltammetry in supporting electrolytes containing 0.1 M NaOH or 0.1 M NaOH + 0.1 M Na₃Cit at a graphite and a mercury thin-film electrodes. The best conditions were found for the coulometric determination of Pb by the oxidation of Pb(0) to Pb(II) in the presence of 5- to 20-fold amounts of Bi(III) and Cu(II) within the range 0.2–2 mg Pb(II) with an error and a relative standard deviation of less than 0.5%. Along with the procedure proposed previously for the determination of Pb(II) and Pb(IV) present simultaneously using a platinum gauze electrode, this procedure was applied to the determination of Pb(II) and Pb(IV) in samples of high-T_c. Cu-Bi superconductors. For samples of high-T_c. Bi-Pb-A-Cu-0 superconductors (A = Ba or Sr-Ca) containing from 2 to 12% Pb(II), the relative standard deviation was less than 0.5%; for 0.6–7% Pb(IV), it was 1-0.2%.     

Copper ring-disk microelectrodes: fabrication, characterization, and application as an amperometric detector for capillary columns

A novel approach to the fabrication of metal ring-disk (RD) microelectrodes is presented that employs flexible chemical vapor deposition (CVD) and electrode modification techniques. Specifically, the development of a copper ring-disk microelectrode is described utilizing a combination of CVD coating, electroetching, and electroplating. Initially, a 25 μm diameter tungsten wire is concentrically coated by CVD with an insulating layer of silica, a layer of tungsten metal, and finally, a second outer layer of silica. The copper surface was prepared by first creating micrometer cavities by electrochemical etching the tungsten in hydroxide solutions followed by electrodeposition of copper from aqueous solutions of Cu(II). Each step of the process was characterized by scanning electron microscopy, optical microscopy, and cyclic voltammetry, demonstrating the preparation of a viable metal-based dual ring-disk microelectrode system. For the purpose of demonstrating the concept of introducing specific selectivity into the device, amperometric detection of galactose in 0.1 M NaOH was performed at +0.60 V in bulk solution and after flow injection analysis in a capillary column.     

An Electrochemical Biosensor with Uricase Immobilized on Functionalized Gold Coated Copper Wire Electrode for Urinary Uric Acid Assay

A new second generation uricase electrode for urinary uric acid determination has been developed by chemically binding both uricase and redox mediator to inexpensive copper wire through simple electrodeposition of gold on copper surface and subsequent functionalization of the gold with L‐methionine. During a 209‐day testing period, the overall electrode performance exhibits in average a low oxidation potential of 0.33 V, a response time of 5 s, a widest linear calibration concentration range (0–2.38 mM, r²>0.9952), a sensitivity of 50 μA mM^?1, and a detection limit of 2.4 μM. The measurement accuracy and precision for the determination of uric acid in human urine specimens were 85.6–95.5 % and 0.3–2.4 %, respectively. The developed uricase electrode is potential for clinical applications.