氮掺杂还原氧化石墨烯负载铂催化剂的制备及甲醇电氧化性能

采用高温热解聚苯胺修饰的氧化石墨烯（PANI-GO）,得到了氮掺杂的还原氧化石墨烯碳材料（N-RGO）,以其负载Pt 制备了Pt/N-RGO纳米结构电催化剂. 采用透射电镜（TEM）、X射线光电子能谱（XPS）、X 射线衍射（XRD）谱及拉曼光谱等技术对N-RGO和Pt/N-RGO的形貌及结构进行了表征,用循环伏安、计时电流等电化学技术研究了Pt/N-RGO电极催化剂对CO溶出反应和甲醇电氧化反应的催化性能. 结果表明：高温热解PANIGO可同时实现GO的还原及其氮掺杂的过程,氮掺杂引起还原氧化石墨烯碳材料表面缺陷结构和导电性的增加;与相应的未掺杂氮样品Pt/RGO相比较,Pt/N-RGO样品上Pt 颗粒的分散更均匀,显示出更强的抗CO毒化能力和更高的甲醇电氧化催化活性及稳定性.     

氮掺杂还原氧化石墨烯负载铂催化剂的制备及甲醇电氧化性能

采用高温热解聚苯胺修饰的氧化石墨烯(PANI-GO),得到了氮掺杂的还原氧化石墨烯碳材料(N-RGO),以其负载Pt制备了Pt/N-RGO纳米结构电催化剂.采用透射电镜(TEM)、X射线光电子能谱(XPS)、X射线衍射(XRD)谱及拉曼光谱等技术对N-RGO和Pt/N-RGO的形貌及结构进行了表征,用循环伏安、计时电流等电化学技术研究了Pt/N-RGO电极催化剂对CO溶出反应和甲醇电氧化反应的催化性能.结果表明:高温热解PANIGO可同时实现GO的还原及其氮掺杂的过程,氮掺杂引起还原氧化石墨烯碳材料表面缺陷结构和导电性的增加;与相应的未掺杂氮样品Pt/RGO相比较,Pt/N-RGO样品上Pt颗粒的分散更均匀,显示出更强的抗CO毒化能力和更高的甲醇电氧化催化活性及稳定性.     

Amperometric Glucose Biosensor Based on Pt‐Pd Nanoparticles Supported by Reduced Graphene Oxide and Integrated with Glucose Oxidase

A novel glucose biosensor was developed based on the immobilization of glucose oxidase (GOx) on reduced graphene oxide incorporated with electrochemically deposited platinum and palladium nanoparticles (PtPdNPs). Reduced graphene oxide (RGO) was more hybridized by chemical and heat treatment. Bimetallic nanoparticles were deposited electrochemically on the RGO surface for potential application of the Pd? Pt alloy in biosensor preparation. The as‐prepared hybrid electrode exhibited high electrocatalytic activities toward H₂O₂, with a wide linear response range from 0.5 to 8 mM (R²=0.997) and high sensitivity of 814×10^?6 A/mMcm². Furthermore, glucose oxidase with active material was integrated by a simple casting method on the RGO/PdPtNPs surface. The as‐prepared biosensor showed good amperometric response to glucose in the linear range from 2 mM to 12 mM, with a sensitivity of 24×10^?6 A/mMcm², a low detection limit of 0.001 mM, and a short response time (5 s). Moreover, the effect of interference materials, reproducibility and the stability of the sensor were also investigated.     

二氧化锆/石墨烯复合材料对亚硝酸盐的电化学传感研究

制备了一种二氧化锆/还原氧化石墨烯(ZrO2NPs/rGO)复合材料修饰电极的亚硝酸盐电化学传感器,并成功用于亚硝酸盐的检测.采用循环伏安法和电流-时间曲线考察了修饰电极的电化学行为.实验结果表明,ZrO2NPs/rGO复合材料修饰电极对亚硝酸盐具有良好的电流响应.在最优实验条件下,电流-时间曲线中的电流响应信号与亚硝酸盐浓度在3.0×10Symbolm@@_7～1.0×10Symbolm@@_6 mol/L和1.0×10Symbolm@@_6～6.0×10Symbolm@@_6 mol/L的范围内呈良好的线性关系,检测限为1.0×10Symbolm@@_7 mol/L(S/N 3).该传感器灵敏性高、稳定性和重现性好.使用此传感器检测实际样品香肠中的亚硝酸盐的回收率为93.7％～110.4％,相对标准偏差为1.6％～2.1％.     

DNA Induced FePt Bimetallic Nanoparticles on Reduced Graphene Oxide for Electrochemical Determination of Dopamine

FePt bimetallic nanoparticles were formed on reduced graphene oxide(rGO) with the help of double-stranded DNA(dsDNA) via a simple and universal route to obtain a FePt/DNA-rGO composite. The FePt nanoparticles with an average size of about 5 nm were well dispersed on rGO. FePt/DNA-rGO modified glassy carbon electrode(GCE) exhibited excellent electrocatalytic activity for the oxidation of dopamine(DA) with a detection limit of 100 nmol/L(S/N = 3). In addition, the FePt/DNA-rGO based electrochemical sensor showed an excellent selectivity for DA in the presence of ascorbic acid(AA), uric acid(UA) and other interference reagents. The as-prepared electrochemical biosensor shows great promise in the application of clinical diagnostics.     

Manganese Oxide Nanoparticles/Reduced Graphene Oxide as Novel Electrochemical Platform for Immobilization of FAD and its Application as Highly Sensitive Persulfate Sensor

In this study, manganese oxide nanoparticles/reduced graphene oxide(MnOxNPs/rGO) was used as support for strong immobilization of flavin adenine dinucleotide(FAD). A thin film of rGO cast on the electrode surface, followed by performing electrodeposition of MnOxNPs at applied constant potential of +1.4 V vs. Ag/AgCl for 200 s. Finally, FAD was electrodeposited onto the rGO/MnOxNPs film by potential cycling between 1.0 to ?1.0 V in solution containing 1 mg ml^?1 FAD. Electrochemical properties and catalytic activity of GCE/rGO‐MnOxNPs/FAD toward persulfate (S₂O₈^2?) reduction was investigated. Under optimized condition, the concentration calibration range, detection limit, and sensitivity were 0.1 μM–2 mM, 90 nM and 125.8 nA/μM, respectively, using hydrodynamic amperometry technique.     

Selective and Simultaneous Determination of Dihydroxybenzene Isomers Based on Green Synthesized Gold Nanoparticles Decorated Reduced Graphene Oxide

In the present study, we report the simultaneous electrochemical determination of hydroquinone (HQ), catechol (CC) and resorcinol (RC) at gold nanoparticles (Au‐NPs) decorated reduced graphene oxide (RGO) modified electrode. An enhanced and well defined peak current response with a better peak separation of HQ, CC and RC is observed at RGO/Au‐NPs composite than that of RGO and Au‐NPs modified electrodes. The fabricated modified electrode shows a wide linear response in the concentration range of 3–90 µM, 3–300 µM and 15–150 µM for HQ, CC and RC, respectively. The detection limit of HQ, CC and RC is found as 0.15 µM, 0.12 µM and 0.78 µM, respectively.     

Preparation of Sulphur-containing Aromatic Amines by Reduction of the Corresponding Aromatic Nitro Compounds with Hydrazine Hydrate over Iron Oxide Hydroxide Catalyst

The sulphur-containing aromatic amines are an important class of compounds frequently used as key intermediates in the synthesis of pharmaceutical products1,2, dyestuffs3-6 and polymers7. The usual methods for preparing sulphur-containing aromatic amines …     

Electrochemical Synthesis of β‐Cyclodextrin Functionalized Silver Nanoparticles and Reduced Graphene Oxide Composite for the Determination of Hydrazine

β‐cyclodextrin (β‐CD) functionalized silver nanoparticles (AgNPs) and reduced graphene oxide (RGO) via one step electrochemical potentiodyanamic method has been prepared. Scanning electron microscopy, Energy‐Dispersive X‐ray spectroscopy, electrochemical impedance spectroscopy and cyclic voltammetry were used to study the role of β‐CD on preparation of AgNPs and RGO. RGO/β‐CD/AgNPs modified GCE showed good electrochemical activity towards electro‐oxidation of hydrazine in terms of decreasing the over potential and increasing the peak current. The kinetic parameters such as electron transfer coefficient (α) and diffusion coefficient (Do) of the modified electrode towards hydrazine were determined to be 0.66 and 0.97×10^?6 cm² s^?1, respectively. The LOD of our sensor was many folds lower than that of recommended concentration of hydrazine in drinking water by United States Environmental Protection Agency and World Health Organization. The sensor exhibited a wide linear range from 0.08 to 1110 µM and a very low detection limit (LOD) of 1.4 nM. In addition, the sensor selectively determined hydrazine even in the presence of common interferents.     

Fabrication of Non‐enzymatic Electrochemical Glucose Sensor Based on Pd−Mn Alloy Nanoparticles Supported on Reduced Graphene Oxide

Mixed metals alloy nanoparticles supported on carbon nanomaterial are the most attractive candidates for the fabrication of non‐enzymatic electrochemical sensor with enhanced electrochemical performance. In this study, palladium‐manganese alloy nanoparticles supported on reduced graphene oxide (Pd?Mn/rGO) are prepared by a simple reduction protocol. Further, a novel enzyme‐free glucose sensing platform is established based on Pd?Mn/rGO. The successful fabrication of Pd?Mn alloy nanoparticles and their attachment at rGO are thoroughly characterized by various microscopic and spectroscopic techniques such as XRD, Raman, TEM and XPS. The electrochemical activity and sensing features of designed material towards glucose detection are explored by amperometric measurments in 0.1 M NaOH at the working voltage of ?0.1 V. Thanks to the newly designed Pd?Mn/rGO nanohybrid for their superior electrorochemical activity towards glucose comprising the admirable sensing features in terms of targeted selectivity, senstivity, two linear parts and good stability. The enhanced electrochemical efficacy of Pd?Mn/rGO electrocatalyst may be credited to the abundant elecrocatalytic active sites formed during the Pd?Mn alloying and the electron transport ability of rGO that augment the electron shuttling phenomenon between the electrode material and targeted analyte.     

Direct‐methanol Fuel Cell Based on Functionalized Graphene Oxide with Mono‐metallic and Bi‐metallic Nanoparticles: Electrochemical Performances of Nanomaterials for Methanol Oxidation

The catalysts based on 2‐aminoethanethiol functionalized graphene oxide (AETGO) with several mono‐metallic and bi‐metallic nanoparticles such as rod gold (rAuNPs), rod silver (rAgNPs), rod gold‐platinum (rAu‐Pt NPs) and rod silver‐platinum (rAg‐Pt NPs) were synthesized. The successful synthesis of nanomaterials was confirmed by various methods. The effective surface area (ESA) of the rAu‐Pt NPs/AETGO is 1.44, 1.64 and 2.40 times higher than those of rAg‐Pt NPs/AETGO, rAuNPs/AETGO and rAgNPs/AETGO, respectively, under the same amount of Pt. The rAu‐Pt NPs/AETGO exhibited a higher peak current for methanol oxidation than those of comparable rAg‐Pt NPs/AETGO under the same amount of Pt loading.     

Electrochemical Sensor‐Based Ruthenium Nanoparticles on Reduced Graphene Oxide for the Simultaneous Determination of Ethinylestradiol and Amoxicillin

The composite material of reduced graphene and Ru nanoparticles (rGO/RuNP) was obtained by electrochemical oxidation of ruthenium nanoparticles immobilised on the glassy carbon electrode (GCE) surface and used for simultaneous electroanalysis of drugs. There are many discussions in the scientific community about the decrease in therapeutic efficacy of contraceptives when associated with antibiotics. The antibiotic effect of the antagonist can increase the contraceptive excretion levels in urine, indicating a reduction in the body and thus a decrease in the desired effect. Using the DPV technique, it was possible to quantify ethinylestradiol (EE2) and amoxicillin (AMX) with a linear response range, 5.50x10⁻⁸ – 1.20x10⁻⁶ mol L⁻¹, and LOD, 2.04 nmol L⁻¹ and 1.63 nmol L⁻¹, respectively. The results for the electrochemical behaviour of EE2 and AMX using GCE/rGO/RuNP were compared with GCE/rGO and GCE. The GCE/rGO/RuNP showed greater stability and separation anodic peak currents, suitable for the quantification of organic molecules in samples of environmental interest, as well as clinical and food samples.     

Protein‐Directed In Situ Synthesis of Gold Nanoparticles on Reduced Graphene Oxide Modified Electrode for Nonenzymatic Glucose Sensing

A novel nonenzymatic glucose sensor was developed based on well‐dispersed gold nanoparticles, which were in situ grown under direction of protein on a reduced graphene oxide modified electrode. This electrode exhibited high electrocatalytic activity towards glucose oxidation without use of any enzyme or mediator. In application for the amperometric detection of glucose, a wide linear range of 0.02–16.6 mM, low detection limit of 5 µM and good selectivity were obtained. The attractive analytical performances of the proposed glucose sensor, coupled with the facile preparation method, provide a promising electrochemical platform for the development of effective nonenzymatic sensors.     

原位合成钴/还原氧化石墨烯纳米粒子催化氨硼烷制氢

采用简单的原位还原合成方法,利用具有温和还原性能的氨硼烷作为还原剂,在室温下一步还原氧化石墨烯和氯化钴混合溶液制备了还原氧化石墨烯负载钴纳米复合材料催化剂. 利用所制备的钴/还原氧化石墨烯催化剂催化氨硼烷水解制氢,发现钴/还原氧化石墨烯具有优异的催化性能. 相对于没有负载的钴纳米粒子以及采用硼氢化钠作为还原剂制备的钴/还原氧化石墨烯催化剂,采用氨硼烷还原制备的钴/还原氧化石墨烯催化剂表现出更加优越的催化性能. 动力学测试表明,钴/还原氧化石墨烯催化氨硼烷水解反应为零级反应,同时钴/还原氧化石墨烯催化剂催化氨硼烷水解反应的活化能为27.10 kJ·mol^-1,低于大部分已报道的其它催化剂,甚至一些贵金属催化剂的活化能. 钴/还原氧化石墨烯催化剂有着稳定的循环使用性,特别是其具有的磁性使得它能够直接从溶液中通过磁力回收,极具应用前景. 这种简单有效的合成方法有望推广到其它的金属-还原氧化石墨烯纳米复合材料体系.     

Reduced Graphene Oxide Supported Cobalt Bipyridyl Complex for Sensitive Detection of Methyl Parathion in Fruits and Vegetables

Herein, we are described a green route to prepare reduced graphene oxide supported cobalt inorganic complex nanocomposite (GRGO/[Co(bpy)₃]) (bpy=2,2′‐bipyridine) through facile and wet chemical approach. The formation of the nanocomposite was confirmed through suitable physical and chemical characterization techniques. The GRGO/[Co(bpy)₃] nanocomposite was coated on the pretreated glassy carbon electrode (GCE). The GCE/GRGO/[Co(bpy)₃] modified electrode has excellent electrocatalytic ability towards methyl parathion reduction, while the overpotential drops drastically to –0.18 V (vs. Ag/AgCl). Moreover, the effect of concentration, scan rate and electrolyte pH were detail studied. Besides, the linear response range was 0.05‐1700 μM and the detection limit was 0.0029 μM (S/N=3) and the sensitivity was 1.8197 μA μM⁻¹ cm⁻². Moreover, the fabricated electrode has high level of selectivity, which delivers satisfactory repeatability, reproducibility and stability. The sensing method was successfully demonstrated in real samples such as, tomato and apple samples.     

Functionalization of Reduced Graphene Oxide with β‐cyclodextrin Modified Palladium Nanoparticles for the Detection of Hydrazine in Environmental Water Samples

A sensitive and selective hydrazine sensor was developed by β‐cyclodextrin modified palladium nanoparticles decorated reduced graphene oxide (PdNPs‐β‐CD/rGO) nanocomposite. The PdNPs‐β‐CD/rGO hybrid material was prepared by simple electrochemical method. The hydrophobic cavity of β‐CD ineracts with palladium nanoparticles by hydrophobic interaction and further it is uniformly assembled on the rGO surface through hydrogen bond formation, which is clearly confirmed by FT‐IR, FESEM and TEM. The high electrocatalytic activity of hydrazine oxidation was observed at −0.05 V (vs. Ag/AgCl) on PdNPs‐β‐CD/rGO modified electrode; due to the excellent stabilization, high catalytic activity and large surface area of the PdNPs‐β‐CD/rGO composite. The PdNPs‐β‐CD/rGO fabricated hydrazine sensor exhibited an excellent analytical performance, including high sensitivity (1.95 μA μM⁻¹ cm⁻²), lower detection limit (28 nM) and a wide linear range (0.05 to 1600 μM). We also demonstrated that the PdNPs‐β‐CD/rGO nanocomposite modified electrode is a highly selective and sensitive sensor towards detection of hydrazine among the various interfering species. Hence, the proposed hydrazine sensor is able to determine hydrazine in different water samples.     

Novel Metal Oxide Support with Water Activation Ability for Use in Direct Methanol Fuel Cell

A new principle for designing catalyst supports with water activation ability was proposed. According to this principle, stabilized nickel(+3) oxides with different dopants were tested as possible support and promoter for Pt catalyst in direct methanol fuel cells. It was found that the chemical and electrochemical stabilities of these novel supports in acidic solution were sufficient. The support doped with Al(+3) has catalytic activity towards methanol electrooxidation while that doped with Co(+3) can improve both activity and poisoning tolerance of the Pt catalyst.     

The Effects of Hydrophobicity and Textural Properties on Hexamethyldisiloxane Adsorption in Reduced Graphene Oxide Aerogels

To expand the applications of graphene-based materials to biogas purification, a series of reduced graphene oxide aerogels (rGOAs) were prepared from industrial grade graphene oxide using a simple hydrothermal method. The influences of the hydrothermal preparation temperature on the textural properties, hydrophobicity and physisorption behavior of the rGOAs were investigated using a range of physical and spectroscopic techniques. The results showed that the rGOAs had a macro-porous three-dimensional network structure. Raising the hydrothermal treatment temperature reduced the number of oxygen-containing groups, whereas the specific surface area (S_BET), micropore volume (V_micro) and water contact angle values of the rGOAs all increased. The dynamic adsorption properties of the rGOAs towards hexamethyldisiloxane (L2) increased with increasing hydrothermal treatment temperature and the breakthrough adsorption capacity showed a significant linear association with S_BET, V_micro and contact angle. There was a significant negative association between the breakthrough time and inlet concentration of L2, and the relationship could be reliably predicted with a simple empirical formula. L2 adsorption also increased with decreasing bed temperature. Saturated rGOAs were readily regenerated by a brief heat-treatment at 100 °C. This study has demonstrated the potential of novel rGOA for applications using adsorbents to remove siloxanes from biogas.