Nafion-离子液体-修饰碳糊电极在抗坏血酸和尿酸存在下选择性测定多巴胺

用Nafion和亲水性离子液体溴化1-辛基-3-甲基咪唑([OMIM]Br)作修饰剂制作了Nafion-离子液体-修饰碳糊电极;在0.1 mol/L磷酸盐缓冲溶液(pH 7.40)中,用循环伏安法(CV)和方波伏安法(SWV)研究了多巴胺在该修饰电极上的电化学行为,建立了抗坏血酸和尿酸存在下选择性测定多巴胺的新方法.研究表明,该修饰电极降低了多巴胺氧化、还原反应的过电位,增大了其氧化、还原反应的峰电流,而抗坏血酸和尿酸在该修饰电极上无响应;在方波伏安曲线上,多巴胺的氧化电流与其浓度在3.0×10-8～2.0×10-6 mol/L范围内呈线性关系,检出限为1.0×10-8 mol/L.该法可用于注射液和模拟生物样品中多巴胺的测定.     

石墨烯/十二烷基硫酸钠复合物修饰碳糊电极测定氯霉素

以液体石蜡和硅油为混合粘合剂,与石墨粉混合制备了碳糊电极基底电极,将石墨烯/十二烷基硫酸钠复合物修饰在基底碳糊电极上,得到了基于石墨烯复合物的新型修饰碳糊电极。应用扫描电镜和循环伏安法分别研究了该电极的表面特性和电化学性质,结果表明,石墨烯和十二烷基硫酸钠修饰的碳糊电极增大了比表面积,有利于电子传递。在pH 3.0的HAc-NaAc缓冲溶液中,该修饰碳糊电极对氯霉素具有良好的电化学响应,氧化峰电位为0.194 V,氧化峰电流是基底碳糊电极的10倍。在最优实验条件下,该氧化峰电流与氯霉素的浓度在1.0×10~(-8)~5.0×10~(-4)mol/L范围内呈良好的线性关系,检出限为5.0×10~(-9)mol/L。该方法简便,重现性及选择性好,用于测定氯霉素滴眼液和虾中氯霉素残留,结果满意。     

Electrocatalytic Determination of the antibiotic Levofloxacin using modified carbon paste electrode with a poly-murexide thin film voltammetrically

In this work, a simple, cheap, sensitive, and selective modified carbon paste electrode is proposed for the electroanalytical determination of Levofloxacin (LEVO), the drug used to treat pneumonia caused by coronavirus. The electrochemical polymerization method was applied to create a thin poly-murexide film (POMUR) on the bare carbon paste electrode (BCPE) surface to enhance its electrocatalytic activity. The peak current response of LEVO obtained by POMUR/CPE was increased by 14.2 μA compared to BCPE. Scanning electron microscopy (SEM) and cyclic voltammetry (CV) techniques were employed to characterize BCPE and POMUR/CPE. Under the optimal experimental circumstances, the prepared sensor was capable of determining LEVO with a low limit of detection (LOD) of 7.18 nM (S/N = 3) for a linear dynamic range of 25 – 1 × 10³ nM utilizing differential pulse voltammetry (DPV). Moreover, the practical applicability of POMUR/CPE for determining LEVO in pharmaceutical formulations and biological samples (human serum) demonstrated high sensitivity and selectivity with a recovery of 95.08 – 100.5 %.     

基于表面活性剂单分子层修饰碳糊电极的一氧化氮电化学传感器及其应用

报道了一种表面活性剂单分子层修饰碳糊电极,并用于NO的高灵敏电化学检测。研究表明,表面活性剂通过烷基链在电极表面形成的疏水性单分子层微环境对NO的电化学响应具有较好的促进作用。其中,阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)对NO的电化学氧化表现出最强的催化活性和增敏作用。在Nafion膜覆盖的CTAB修饰碳糊电极上,NO的安培响应与其浓度在3.6×10-8～1.8×10-5mol/L范围内呈良好的线性关系,检出限为1.8×10-8mol/L。该电极作为低成本、高灵敏的NO电化学传感器,被成功应用于大鼠肺组织细胞中NO释放的实时监测。     

Selective determination of cysteine in the presence of tryptophan by carbon paste electrode modified with quinizarine

A sensitive and selective electrochemical method for the determination of L-cysteine was developed using a modified carbon paste electrode (MCPE) with quinizarine. Cyclic voltammetry was used to investigate the redox properties of this modified electrode at various solution pH values and at various scan rates. The apparent charge transfer rate constant, ks and transfer coefficient for electron transfer between quinizarine and carbon paste electrode (CPE) were calculated as 2.76 s^?1 and 0.6, respectively. This modified carbon paste electrode shows excellent electrocatalytic activity toward the oxidation of L-cysteine in a phosphate buffer solution (pH 7.0). The linear range of 1.0 × 10^?6 to 1.0 × 10^?3 M and a detection limit (3s) of 2.2 × 10^?7 M were observed in pH 7.0 phosphate buffer solutions. In differential pulse voltammetry, the quinizarine modified carbon paste electrode (QMCPE) could separate the oxidation peak potentials of L-cysteine and tryptophan present in the same solution, though at the unmodified CPE the peak potentials were indistinguishable. This work introduces a simple and easy approach to selective detection of L-cysteine in the presence of tryptophan. Also, the modified electrode was employed for the determination of L-cysteine in the real samples such as serum of blood and acetylcysteine tablet.     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Nanostructured Conducting Polymer/Copper Oxide as a Modifier for Fabrication of L‐DOPA and Uric Acid Electrochemical Sensor

A modified electrode was prepared by modification of the carbon paste electrode (CPE) with a nanostructured material. This nanostructure with electrocatalytic activity was synthesized by combination of poly pyrrole and copper oxide nanoparticles (PPy/CuO). The structure and morphology of PPy/CuO was studied. The fabricated modified electrode (CPE‐PPy/CuO) exhibited an excellent electrocatalytic activity toward levodopa (L‐DOPA) and uric acid (UA) oxidation because of high conductivity, low electron transfer resistance and catalytic effect. The CPE‐PPy/CuO had a lower overvoltage and enhanced electrical current with respect to the bare CPE for both L‐DOPA and UA. Also, the modified electrode showed a good resolution for the overlapped anodic peaks of L‐DOPA and UA. This electrode was used for the successful simultaneous determination of L‐DOPA and UA. The electrochemical sensor responded to L‐DOPA and UA in the concentration range of 0.050–1200 μM and 0.040–2000 μM, respectively. The detection limits were obtained by differential pulse voltammetry as 15 nM for L‐DOPA and 20 nM for UA. Finally, the proposed electrode was used for determination of L‐DOPA and UA in real samples using standard addition method.     

硫脲在10-甲基吩噻嗪修饰碳糊电极上的电催化氧化及电分析方法研究

研究了硫脲(Thiourea,Tu)在10-甲基吩噻嗪修饰碳糊电极(MPT/CPE)上的电催化氧化行为.结果表明,Tu在裸碳糊电极(CPE)上的直接电化学氧化过程十分迟缓,MPT/CPE对Tu的电化学氧化具有良好的催化作用.用计时电流法(CA)测定了Tu在MPT/CPE上的电极过程动力学参数,测得电荷传递系数α=0.61,电催化氧化反应的速率常数k=(1.96±0.10)×104(mol/L)-1·s-1.用方渡伏安法(SWV)测得催化氧化峰电流与Tu浓度在1.0×10-6～8.0×10-3mol/L范围内呈良好的线性关系,线性回归方程为,Ips(μA)=10.836c(10-3mol/L)+5.326,R=0.9984,检出限为2.2×10-7mol/L(S/N=3).方法可用于Tu的电化学法测定.     

Application of Carbon Paste Electrode Modified with Carbon Nanofibres/Polyaniline/Platinum Nanoparticles as an Electrochemical Sensor for the Determination of Bezafibrate

The present study deals with the development of an electrochemical sensor for quantitative determination of Bezafibrate (BZF) based on carbon nanofibers/polyaniline/platinum nanoparticles modified carbon paste electrode (CNF/PANI/Pt/CPE). BZF is a fibric acid derivative and is used largely in the treatment of lipid disorders. The nanocomposite was synthesized by in situ polymerization of aniline using ammonium persulphate and platinum nanoparticles were uniformly decorated on the CNF/PANI surface by reducing hexachloroplatinic acid using sodium borohydride. The electrochemical response of BZF at CNF/PANI/Pt/CPE was studied using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The above study resulted into significant improvement of the electrochemical signal towards the oxidation of BZF, revealing that the oxidation process is highly favorable at the surface of modified electrode. The anodic peak current I_p (μA) is found to be linearly dependent on BZF concentration in the range of 0.025 μM to 100 μM with a detection limit of 2.46 nM. The practical analytical utilities of the sensor were investigated by performing the experiments on synthetic pharmaceutical formulations, human blood serum and urine samples which offered good recovery, suggesting the high efficacy and authenticity of CNF/PANI/Pt/CPE sensor for BZF determination.     

Novel Fe2O3@CeO2 Coreshell‐based Electrochemical Nanosensor for the Voltammetric Determination of Norepinephrine

A new selective carbon paste electrode (CPE), was applied as an electrochemical sensor for the detection of norepinephrine (NOE). The sensor was modified with 6‐amino‐4‐(3,4‐dihydroxyphenyl)‐3‐methyl‐1,4‐dihydropyrano[2,3‐c],pyrazole‐5‐carbonitrile (ADPC) assisted Fe₂O₃@CeO₂ coreshell nanoparticles (CNs) synthesized by simple method. To identify the redox properties of the modified electrode, and to examine its electrochemical properties, cyclic voltammetry (CV), chronoamperometry and differential pulse voltammetry (DPV) were conducted. Through electrochemical investigations, the coefficient of electron transfer between ADPC and the CNs/CPE (i. e. carbon paste electrode which was modified with CNs), the apparent charge transfer rate constant (k_s), and the diffusion coefficient (D) were calculated. The NOE oxidation occurred at the optimum pH of 7.0 and a potential that was about 235 mV less positive than that of the unmodified carbon paste electrode. The interaction between the two metals in the Fe₂O₃@CeO₂ coreshell led to an increase in the surface area and, consequently a sharp increase in the current. The differential pulse voltammogram of NOE showed two linear dynamic ranges an excellent detection limit (3σ) of 40 nM. In addition, NOE, AC and Trp were simultaneously determined at the modified electrode. Finally, NOE was quantitated in a number of real samples.     

Electroanalysis of Carbendazim using MWCNT/Ca‐ZnO Modified Electrode

The present research involves the report on electrochemical deportment of Carbendazim (MBC) at multiwalled carbon nanotubes and calcium‐doped zinc oxide nanoparticles altered nanocomposite based carbon paste electrode (MWCNTs/Ca‐ZnO‐CPE). The modified carbon paste evidenced manifest electrocatalytic behavior for MBC in 0.2 M phosphate buffer (PB) solutions. Cyclic voltammetry (CV), linear sweep voltammetry (LSV), and square wave voltammetry (SWV) techniques were used for the analysis. The working electrode assembly exhibits faster electron transfer of MBC with increase in the peak current. At bare CPE, MBC showed maximum peak current of 1.098 μA at potential 0.7568 V whereas at MWCNT/Ca‐ZnO/CPE peak current of 5.203 μA was observed at potential 0.7541 V in 0.2 M PBS of pH 7.0 at the sweep rate of 50 mV s^?1. The synthesized 5 % Ca‐ZnO nanoparticles (NPs) were characterized by X‐ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive X‐ray analysis (EDX), and Transmission electron microscopy (TEM) analysis. Various factors influencing the voltammetry of MBC such as pre‐concentration time, pH, sweep rate, and amount of MBC were studied and from the studies we observed that the response was found to be diffusion‐controlled. The concentration variation studies for MBC was watched in the linear working range of 0.01 μM to 0.45 μM and the detection limit was found by SWV technique.     

An electrochemical DNA sensor based on a layers-film construction modified electrode

This work developed a relatively inexpensive and layers-film construction electrochemical sensor for DNA recognition and its performance was investigated. The Fe(3)O(4) magnetic nanoparticles-cysteine were immobilized on the carbon paste electrode (CPE) surface using magnetic force. Multiwalled carbon nanotubes (MWCNTs), gold nanoparticles (GNPs), and chitosan (Chi) were used successively to coat on the electrode surface. The thiolated capture probe was assembled and competitively hybridized with the target nucleic acid and biotinylated response probe. The electrochemical behavior was analyzed by cyclic voltammetry and electrochemical impedance spectroscopy. In addition, the sensor performance was also analyzed by introducing the notion of detection efficiency. The experimental results showed that although the electron transfer capability of the CPE is less strong than that of a metal electrode used in the DNA sensor, the materials modified on the CPE could significantly improve the performance. A detection limit of 1 nM of target DNA and a sensitivity of 2.707 × 10(3) mA M(-1) cm(-2) were obtained. Although the resulting detection limit was not remarkable, further experiments could improve it.     

美索巴莫在［BnMIM］PF6修饰碳糊电极上的电催化氧化及电分析方法

研究了美索巴莫（MET）在离子液体1-苄基-3-甲基咪唑六氟磷酸盐［BnMIM］PF6修饰碳糊电极（［BnMIM］PF6/CPE）上的电催化氧化行为和电化学动力学性质,并用循环伏安法（CV）、计时电流法（CA）测得MET在［BnMIM］PF6/CPE上的电极反应过程动力学参数。实验结果表明,MET在［BnMIM］PF6/CPE上发生了受扩散控制的不可逆电化学氧化过程。用方波伏安法（SWV）测得MET氧化峰电流（Ipa）与其浓度在3.0×10-5~1.0×10-2 mol?L-1范围内呈良好线性关系,检出限（S/N=3）为3.3×10-6 mol?L-1。同时运用SWV法对市售美索巴莫片进行电化学定量测定,RSD为1.5%~2.5%,加标回收率为98%~99%。     

双酚A在SDS现场自组装膜与[bupy]PF6复合修饰碳糊电极上的电催化氧化及电分析方法

研究了双酚A(BPA)在十二烷基硫酸钠(SDS)现场自组装膜与离子液体N-丁基吡啶夫氟磷酸盐([ bupy]PF6)复合修饰碳糊电极(SDS-[ bupy]PF6/CPE)上的电催化氧化行为和电化学动力学性质.实验结果表明,在SDS-[ bupy]PF6/CPE上BPA发生了一受扩散控制的不可逆电化学氧化过程,用循环伏安(CV)法和计时电流(CA)法测得BPA在SDS-[bupy]PF6/CPE上的电极反应过程动力学参数.用方波伏安(SWV)法测得BPA氧化峰电流(Ipa)与其浓度在1.0×10-5～ 1.0×10-3 mol/L范围内呈良好的线性关系,线性方程为Ipa(μA) =2.635 +51.30c( 10-3 mol/L),r =0.998 1,检测限(S/N=3)为3.01×10-7 mol/L,同时运用SWV法对湖水样品中双酚A的含量进行了电化学定量测定.     

Electrochemical performances of C/Fe nanocomposite and its use for mediator-free glucose biosensor preparation

C/Fe nanocomposite (CFN) was synthesized by a procedure similar to an exfoliation/adsorption process to intercalate Fe³⁺ into graphite oxide (GO) layers and would be reduced in a H₂ atmosphere. The results of X-ray diffractometry (XRD) and transimission electron microscopy (TEM) show that the form of CFN is carbon nanotube-Fe nanoparticle composite with α-Fe distributed on the nanotube wall. Paste electrode has been constructed using CFN mixed with paraffin. The electrochemical characteristics of such carbon-Fe nanocomposite paste electrode (CFNPE) has been compared with that of carbon paste electrode (CPE) and evaluated with respect to the electrochemistry of potassium ferricyanide, ascorbic acid and cysteine by cyclic voltammetry. CFNPE can accelerate the electron-transfer to improve the electrochemical reaction reversibility. To fabricate the third-generation glucose biosensor, glucose oxidase (GOD) was immobilized on CFNPE surface with Nafion covered after a pretreatment. Oxygen, ascorbic acid and uric acid have no interference with the glucose detection. The biosensor displays a remarkable sensitivity and stability and the results used in the determination of glucose in the human serum samples are satisfactory.     

Sensitive Voltammetric Determination of Captopril Using a Carbon Paste Electrode Modified with Nano-TiO2/Ferrocene Carboxylic Acid

A carbon paste electrode (CPE) modified with ferrocene carboxylic acid (FcCA) and TiO2 nanoparticles was constructed by incorporating TiO2 nanoparticles and ferrocene carboxylic acid into the carbon paste matrix.The electrochemical behavior of captopril (CAP) at the surface of the modified electrode was investigated using electroanalytical methods.The modified electrode showed excellent electrocatalytic activity for the oxidation of CAP in aqueous solutions at physiological pH values.Cyclic voltammetric curves showed that the oxidation of CAP at the surface of the modified electrode reduced its overpotential by more than 290 mV.The modified electrode was used for detecting captopril using cyclic voltammetry and square wave voltammetry techniques.A calibration curve in the range of 0.03 to 2400μmol/L was obtained that had a detection limit of 0.0096 μmol/L (3σ) under the optimized conditions.The modified electrode was successfully used for the determination of captopril in pharmaceutical and biological samples.     

氧化石墨烯/铁氰化铈修饰玻碳电极同时测定扑热息痛和咖啡因

采用滴涂法和电沉积法制备了氧化石墨烯/铁氰化铈(CeFe(CN)6)纳米复合膜修饰玻碳电极。用扫描电镜对氧化石墨烯和氧化石墨烯/CeFe(CN)6纳米复合膜进行了表征。分别用循环伏安法和差分脉冲伏安法研究了扑热息痛和咖啡因在修饰电极上的电化学行为。结果表明,在0.1 mol/L醋酸盐缓冲溶液(pH5.0)中,扑热息痛和咖啡因在此修饰电极上具有良好的电化学行为,扑热息痛和咖啡因分别在1.0×10-7～6.0×10-5mol/L和1.0×10-6～1.3×10-4mol/L浓度范围内与电化学响应信号呈良好的线性关系,相关系数分别为0.990和0.992;信噪比为3时,扑热息痛和咖啡因检出限分别为5.0×10-8mol/L和5.2×10-7mol/L。将本方法用于人尿样品分析,回收率为96.1%～105.4%。     

新型聚中性红膜修饰碳糊电极的制备、表征及应用

运用一种新型的化学引发-电聚合方式将中性红膜固定到碳糊电极表面,制备出聚中性红薄膜修饰碳糊电极(PNR/CPE)。利用循环伏安法(CV)和交流阻抗谱(EIS)对修饰电极的电化学性能进行研究,借助于扫描电子显微镜(SEM)对修饰电极表面进行表征,并采用红外吸收光谱法(IR)和紫外可见吸收光谱法(UV-Vis)对PNR薄膜结构进行测试。结果表明,中性红成功地固定在碳糊电极表面,修饰电极的表面呈现特定的立体化结构,表面的电活性位点增多,电催化性能增大。在优化条件下,将该电极应用于鲱鱼精DNA(hs DNA)的检测,PNR电极上出现了1对较强的氧化还原峰,峰电流与其浓度在1.0×10~(-6)~8.0×10~(-5)mol/L范围内呈良好的线性关系,检出限为1.0×10~(-7)mol/L。     

High Sensitive Sensor Based on Carbon Nanotube Electrode for Determination of Lanthanum in the Presence of Calcon Carboxylic Acid

In this paper we have investigated the electrochemical activity of lanthanum chloride (La (III)) in the presence of calcon carboxylic acid (CCA) using a multi-walled carbon nano tube/carbon paste electrode (CNT/CPE). The peak current increases linearly with increasing of the La (III) concentration. For this purpose, a few electrochemical methods such as cyclic, differential pulse voltammetry, linear sweep and hydrodynamic voltammetry, and chronoamperometry were used. The results show that calcon carboxylic acid as a ligand was useful for determination of La (III) and was able to improve its sensitivity. Cyclic voltammetry was used for study of reduction reaction of La (III) at the surface of modified electrode. The electrochemical parameters for La (III) at the surface of CNT/CPE, such as diffusion coefficient (D/ cm² s ^?1 = 5.26 × 10^?6), the electron transfer coefficient, (α = 0. 43), and the reduction rate constant, (k/ M s^?1 = 2.33 (±0.015) × 10²), were determined using voltammetry methods, which with the detection limit of La (III) by differential pulse voltammetry was found to be 1.3 nM. The combination of CCA with CNT as mediators in carbon paste electrode showed that this electrode is capable, sensitive, and simple to quantify La (III) in real samples with an average recovery of 97.64%.     

Electrocatalytic determination of epinephrine and uric acid using a novel hydroquinone modified carbon paste electrode

A sensitive and selective electrochemical method for the determination of epinephrine(EP) was developed using a modified carbon paste electrode(MCPE) with 2,2’-[3,6-dioxa-1,8-octanediylbis(nitriloethylidyne)]-bis-hydroquinone(DOH).Cyclic voltammetry was used to investigate the redox properties of this modified electrode at various solution pH values and at various scan rates.In differential pulse voltammetry,the modified electrode could separate the oxidation peak potentials of EP and uric acid(UA) present in the solution but at the unmodified CPE the peak potentials were indistinguishable.This method was also examined for determination of EP in EP injection.