新型高温、长寿命氯化物熔盐参比电极的制备与研究

本文介绍一种全固态离子导电玻璃盐桥制备方法,并以此设计新型的Ag/AgCl高温参比电极.该电极制作简单, 具有电位稳定,重现性好,使用寿命长,不污染研究体系等特点.可在多种氯化物熔盐体系中反复使用,适用温度范围 400~900℃.     

Nafion修饰Ag/AgCl参比电极的研制及其在pH电化学传感器中的应用

制备了Nafion修饰的Ag/AgCl参比电极,参比电极电位(25℃)为-47.5±1mV,制备的电极有良好的重现性,电极电位不受溶液pH值和Cl-浓度变化的影响,有良好的抗S2-I、-离子干扰能力,且有较好的抗脉冲电流干扰能力。该参比电极适用于间歇式测试场合,可以保证稳定的参比电位;可用于基于W氧化物pH电极的电化学传感器,传感器的内阻为22kΩ,小于玻璃pH电极计内阻(1~10MΩ)。     

Long-term equilibrium potential and electrochemical impedance study of Ag/AgCl electrodes used in Harned Cell measurements of pH

A long term study of the voltage and electrochemical impedance characteristics of Ag/AgCl electrodes used in Harned Cell measurement of pH is presented. By all the measures investigated the electrodes are shown to degrade only slowly until approximately 200 days after manufacture, after which time the rate of degradation and critical failure of the electrodes increases. The absolute voltage drift of the electrodes may not be easily measured, so parameters determined directed or indirectly by electrochemical impedance spectroscopy have been assessed as a method to produce an alternative indication of electrode integrity. In this respect, resistance to charge transfer has been shown to be a very sensitive measure of changes in the characteristics of the electrodes, and the most closely related to the observed changes in voltage. Evidence is presented to support the hypothesis that the majority of electrode degradation (excluding critical failure) comes from the increased blocking of the microporous structure of the electrodes.     

An Arrayed Micro‐glutamate Sensor Probe Integrated with On‐probe Ag/AgCl Reference and Counter Electrodes

Complete all‐in‐one multi‐arrayed glutamate (Glut) sensors have been constructed on a silicon‐based micromachined probe composed of micro‐platinum (Pt) working electrodes, a micro‐silver/silver chloride (Ag/AgCl) reference electrode (RE), and a micro‐Pt counter electrode (CE). The OCP shift of the electrodeposited Ag/AgCl on‐probe micro‐reference electrode compared with a Ag/AgCl wire is <0.1 mV/h. The composition ratio of Ag, Cl, and Pt on the electrodeposited on‐probe micro‐reference electrode is observed to be 1.00 : 0.48 : 0.02 analyzed by EDS. The miniaturized amperometric Glut biosensors were constructed on working electrode sites (electrode area: ∼8.5×10⁻⁵ cm²) of the microprobe modified with glutamate oxidase (GlutOx) enzyme layers for the selective, fast, and continuous detection of L‐glutamate. The sensor selectivity towards common electroactive interferents has been improved significantly by coating the electrode surface with perm‐selective polymer layers, overoxidized polypyrrole (PPY) and Nafion®. The sensitivity, detection range, and response time of the proposed all‐in‐one Glut biosensors are 204.7±5.8 nA μM⁻¹ cm⁻² (N=5), 4.99–109 μM, and 2.7±0.3 sec, respectively and no interferent signals of AA and DA were observed. The sensor can be reused over 19 times of continuous repetitive operation (total measurement time: ∼4 hours) and the sensor sensitivity can retain up to four weeks of storage.     

Bifunctional AgCl/Ag composites for SERS monitoring and low temperature visible light photocatalysis degradation of pollutant

With the assistance of Polyvinylpyrrolidone (PVP), AgCl/Ag composites were fabricated in N, N-Dimethylformamide (DMF) solvent via a photoactivated route. The size of AgCl particles was in the range of 500 nm to 1 μm and the Ag particle's diameter was about 10–20 nm. Different from those core–shell structures reported before, the Ag nanoparticles were dispersed uniformly both on the surface and in the body of AgCl particles. The generation of such kind of composites was resulted from the reducing ability of DMF and light irradiation during the formation of AgCl particles. The as-obtained AgCl/Ag composites presented great activity for both surface-enhanced Raman scattering (SERS) detection and visible light photocatalytic degradation of organic dyes. Additionally, the AgCl/Ag composites could maintain high photocatalytic activity even though the ambient temperature was as low as 15 °C and recycle photocatalysis experiments indicated that the photocatalyst exhibited higher stability. Such kind of AgCl/Ag composites holds great potential for environmental monitoring devices and pollutant treatments.     

Synthesis of V5+‐doped Ag/AgCl photocatalysts with enhanced visible light photocatalytic activity

V⁵⁺‐doped Ag/AgCl photocatalysts were prepared via the ion exchange method. The catalysts were characterized using X‐ray diffractometry, transmission electron microscopy, and energy‐dispersive X‐ray, X‐ray photoelectron, Fourier transform infrared and ultraviolet–visible spectroscopies. The V⁵⁺‐doped Ag/AgCl photocatalysts show much higher photocatalytic activities than Ag/AgCl under visible light irradiation for methyl orange (MO) decomposition. Especially, the 2.0 wt% V⁵⁺‐doped Ag/AgCl photocatalyst shows the highest photocatalytic activity and also high stability after five cycles. The MO degradation rate during each cycle is almost maintained at 97%. Electron spin resonance spectroscopy and radical trapping experiments reveal that holes play an important role in the photocatalytic process.     

Ag/AgCl/铁-海泡石异相可见光Fenton催化降解双酚A

光-Fenton技术是高级氧化技术中的一种,常用于难降解废水处理,由于其反应速度快、毒性低、反应条件温和而受到广泛关注.然而,传统的光-Fenton体系具有可见光利用率低、回收困难等缺点.为了解决这些问题,本文采用廉价易得、无污染、吸附能力强的天然矿物海泡石作为催化剂载体,并利用Ag/AgCl能够吸收可见光的表面等离子响应这一光学性质,合成了一种有潜力的非均相等离子体光催化剂Ag/AgCl/铁-海泡石催化剂(Ag/AgCl/Fe-S),并对该催化剂的形貌结构、性能和机理等进行了系统研究.通过XRD,SEM,XPS,BET,UV-vis等表征手段对催化剂形貌、结构和可见光性能进行了分析.其中,XRD和SEM结果显示,Ag/AgCl粒子已经成功负载在Fe-海泡石上;XPS结果显示,铁氧化物的组成主要为FeOOH和Fe2O3;UV-vis结果显示,催化剂有较好的可见光吸收性能.以双酚A为目标污染物,分别考察了Ag/AgCl/Fe-S,Ag/AgCl和Fe-海泡石的光-Fenton催化性能.结果显示,Ag/AgCl/Fe-S降解双酚A的效果明显优于另外两种催化剂,在H2O2浓度为6mmol/L,pH为4,光照强度500W,Ag/AgCl/Fe-S催化剂量为1.0 g/L,双酚A初始浓度为10 mg/L的条件下,1 h时,双酚A基本被完全降解,且3 h时,其矿化率达到61.2%;而Ag/AgCl和Fe-海泡石催化剂在同样的条件下完全降解双酚A至少要3 h,且其矿化率分别只有46.61%和28.85%.另外,还分别探讨了H2O2浓度、pH值、光照强度和催化剂剂量对双酚A降解的影响.最后,通过活性物种捕获、ESR、电化学和PL实验对该体系的反应机理进行了探讨.活性物种捕获实验和ESR实验结果表明,羟基自由基(?OH)和空穴(h+)是该体系中的主要活性物种,且Ag/AgCl/Fe-S+H2O2+vis体系产生的?OH明显多于Fe-S+H2O2+vis体系.为了探讨?OH增多的原因,我们进行了电化学实验和PL实验.电化学实验结果显示,Ag/AgCl/Fe-S催化剂具有更低的阻抗,因此有利于电子-空穴分离.PL结果显示,Ag/AgCl/Fe-S催化剂的电子-空穴复合率更低.结合以上实验,我们提出了Ag/AgCl/Fe-S+H2O2+vis体系对双酚A的降解机理,即一方面催化剂能够发生Fenton反应而产生?OH,另一方面,催化剂中的Ag/AgCl在可见光下由于表面等离子响应而产生电子-空穴,空穴本身可作为活性物种降解双酚A.同时,产生的电子被体系中的Fe3+捕获生成Fe2+,从而促进了铁循环,有利于体系中产生更多的?OH.最后,空穴和羟基自由基发生协同作用共同促进污染物降解.     

Preparation and photocatalytic activity of carbon dot/Ag/AgCl

CD (carbon dot)/Ag/AgCl compound photocatalysts with different compounding degrees were prepared via a precipitation method, and their physiochemical properties were characterized by X‐ray diffraction, FE‐SEM, UV–vis and the like. Through the degradation experiment of methyl orange (MO), the effects of different compounding amount and methyl orange concentration on photocatalytic degradation were investigated to find the best ratio. It was found the photocatalytic activity of CD/Ag/AgCl was significantly higher than Ag/AgCl, and the best compounding dosage was 6 mg/l carbon dot. The degradation rate of CD/Ag/AgCl was lower when the initial MO concentration was higher. Five repeated experiments were conducted to test the stability of the catalysts, and showed the MO degradation rates were all above 85%, indicating the CD/Ag/AgCl compound photocatalysts all showed high stability and repeatability. The reaction mechanism of CD/Ag/AgCl photocatalyst was studied by electrochemical experiments and ESR experiments. The results show that the doping of CD effectively improves the photocatalytic degradation ability of MO.     

Development of a micro-planar Ag/AgCl quasi-reference electrode with long-term stability for an amperometric glucose sensor

This paper reports a micro-planar Ag/AgCl quasi-reference electrode (QRE) with long-term stability which is characterized by both long-term potential stability and practical immunity to interference species, and which has been applied for use with an amperometric glucose sensor for plasma glucose. For fabrication, we coated a silver/silver chloride (Ag/AgCl) electrode first with γ-aminopropyltriethoxysilane (γ-APTES) and then with perfluorocarbon polymer (PFCP). Tests demonstrate the new electrode’s ability to remain stable over an 82-day period in 150 mM KCl, and also show its imperviousness to the effects of interference species (1 mM KI and 1 mM KBr), pH, and serum. Furthermore, in tests for glucose concentrations in plasma samples, a good correlation coefficient, 0.954 (n=30, Y=1.02X+0.20), was demonstrated between results obtained with a clinical analyzer and those obtained with an amperometric glucose sensor that used the developed Ag/AgCl QRE, showing that the Ag/AgCl QRE functions well as a reference electrode for plasma samples.     

Fabrication of dual Z-scheme photocatalyst via coupling of BiOBr/Ag/AgCl heterojunction with P and S co-doped g-C3N4 for efficient phenol degradation

Advances in noble metal mediated Z-scheme photocatalytic system have ushered in a climax on environmental remediation. Herein, graphitic carbon nitride (GCN) and phosphorus sulphur co-doped graphitic carbon nitride (PSCN) were synthesized via calcination process. GCN, PSCN and Z-scheme visible light driven (VLD) ternary BiOBr/PSCN/Ag/AgCl nanophotocatalyst were characterized by X-ray diffraction pattern (XRD), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV–visible diffuse reflectance spectra (UV–vis DRS). BiOBr/PSCN/Ag/AgCl nanocomposite exhibited superior visible light driven photocatalytic ability as compared to pristine PSCN, AgCl and BiOBr towards degradation of phenol. The results explicated promising photocatalytic activity along with space separation of photocarriers caused via formation of BiOBr/PSCN/Ag/AgCl Z-scheme heterojunction. The visible light absorption efficacy of BiOBr/PSCN/Ag/AgCl photocatalyst was confirmed by photoluminescence (PL) spectra. Finally, recycling experiments were explored for the mechanistic detailing of phenol photodegradation employing BiOBr/PSCN/Ag/AgCl photocatalyst. After seven successive cycles photodegradation efficacy of photocatalyst was reduced to 90% from 98%. Proposed mechanism of BiOBr/PSCN/Ag/AgCl nanophotocatalyst for degradation of phenol was discussed. OH and O₂⁻ radicals were main reactive species responsible for photocatalytic phenol degradation.     

Electrochemical Immunosensing Chip Using Selective Surface Modification,Capillary‐Driven Microfluidic Control,and Signal Amplification by Redox Cycling

A sensitive electrochemical immunosensing chip is presented by employing (i) selective modification of protein‐resistant surfaces; (ii) fabrication of a stable Ag/AgCl reference electrode; (iii) capillary‐driven microfluidic control; (iv) signal amplification by redox cycling along with enzymatic reaction. Purely capillary‐driven microfluidic control is combined with electrochemical sandwich‐type immunosensing procedure. Selective modification of the surfaces is achieved by chemical reactivity‐controlled patterning and electrochemical deposition. Fluidic control of the immunosensing chip is achieved by spontaneous capillary‐driven flows and passive washing. The detection limit for mouse IgG in the immunosensing chip is 10 pg/mL.     

W18O49 nanorods decorated with Ag/AgCl nanoparticles as highly-sensitive gas-sensing material and visible-light-driven photocatalyst

A novel gas-sensing material and photocatalyst was successfully obtained by decorating Ag/AgCl nanoparticles on the W₁₈O₄₉ nanorods through a clean photochemical route. The as-prepared samples were characterized using combined techniques of X-ray diffractometry, electron microscopy, energy dispersive X-ray spectrometry, and X-ray photoelectron spectroscopy. Gas-sensing measurements indicate that the Ag/AgCl/W₁₈O₄₉ NRs sensors exhibit superior reducing gas-sensing properties to those of bare W₁₈O₄₉ NRs, and they are highly selective and sensitive to NH₃, acetone, and H₂S with short response and recovery times. The Ag/AgCl/W₁₈O₄₉ NRs photocatlysts also possess higher photocatalytic performance than bare W₁₈O₄₉ NRs for degradation of methyl orange under simulated sunlight irradiation. Possible mechanisms concerning the enhancement of gas-sensing and photocatalytic activities of the Ag/AgCl/W₁₈O₄₉ NRs composite were proposed.     

石墨烯量子点-银纳米颗粒复合物用于过氧化氢和葡萄糖比色检测

以石墨烯量子点(GQDs)为还原剂和稳定剂,在其表面原位生长银纳米粒子(AgNPs),制备了具有良好分散性的GQDs/AgNPs纳米复合物,其粒径小于30 nm.GQDs/AgNPs纳米复合物具有类过氧化物酶的催化活性,能有效催化H2O2氧化3,3',5,5'-四甲基联苯胺(TMB)并发生显色反应.稳态动力学分析表明,GQDs/AgNPs催化动力学遵循典型的Michaelis-Menten模型,其催化机理符合乒乓机制.与辣根过氧化物酶(HRP)相比,GQDs/AgNPs纳米复合物具有更强的亲和性.基于GQDs/AgNPs的催化活性和葡萄糖氧化产生H2O2的原理,建立了H2O2和葡萄糖的比色检测方法,检出限分别为0.18和1.6 μmol/L.将本方法应用于血浆中葡萄糖的检测分析,结果与标准方法相符.     

Amperometric Detection of H2O2 Using Gold Electrodes Modified with Starburst PAMAM Dendrimers and Prussian Blue

Gold‐bead electrodes were modified by covalent bonding or physical adsorption of several Starburst PAMAM dendrimers (generations 2.0, 3.0 and 4.0) followed by absorption of Prussian Blue (PB). The covalent dendrimer‐PB‐modified electrodes can be used as amperometric sensors of H₂O₂ in aqueous solution. They offer enhanced sensitivity with correspondingly lower detection and quantification limits compared to similar amperometric detectors.     

Pt／C气体扩散电极制备方法的探索

Ｐｔ／Ｃ气体扩散电极制备方法的探索马永林（青海教育学院,青海,西宁８１０００８）以Ｐｔ／Ｃ为电催化剂的气体扩散电极的制备方法是直接影响该电极电化学性能的重要因素。一般的制备方法是基于将Ｐｔ／Ｃ电催化剂和聚四氟乙烯以及某些有机物或表面活性剂的糊状物涂布...     

Haemoglobin immobilized on nafion modified multi-walled carbon nanotubes for O2, H2O2 and CCl3COOH sensors

A conductive biocomposite film (MWCNTs-NF-Hb) containing multi-walled carbon nanotubes (MWCNTs) incorporated with entrapped haemoglobin (Hb) in nafion (NF) has been synthesized on glassy carbon electrode (GCE), gold (Au), indium tin oxide (ITO) and screen printed carbon electrode (SPCE) separately by potentiostatic methods. The presence of both MWCNTs and NF in the biocomposite film enhances the surface coverage concentration (Γ), and increases the electron transfer rate constant (K_s) to 132%. The biocomposite film exhibits a promising enhanced electrocatalytic activity towards the reduction of O₂, H₂O₂ and CCl₃COOH. The cyclic voltammetry has been used for the measurement of electrocatalysis results of analytes by means of biocomposite film-modified GCEs. The MWCNTs-NF-Hb-modified GCEs’ sensitivity values are higher than the values obtained for other film modified GCEs. The surface morphology of the biocomposite films which have been deposited on ITO has been studied using scanning electron microscopy and atomic force microscopy. The studies have revealed that there was an incorporation of NF and immobilization of Hb on MWCNTs. Finally, the flow injection analysis has been used for the amperometric studies of analytes at MWCNTs-Hb and MWCNTs-NF-Hb film modified SPCEs. The amperometric study results have shown higher slope values for MWCNTs-NF-Hb biocomposite film.     

Enhanced Hydrogen Peroxide Sensing Based on Tetraruthenated Porphyrins/Nafion/Glassy Carbon‐modified Electrodes via Incorporating of Carbon Nanotubes

The incorporation of carbon nanotubes to a Nafion/tetraruthenated cobalt porphyrin/ glassy carbon electrode (GC/Nf/CoTRP vs GC/Nf/CNTCoTRP) enhanced the amperometric determination of hydrogen peroxide. Both electrodes produced a decrease in the overpotential required for the hydrogen peroxide oxidation in about 100 mV compared to glassy carbon under the same experimental conditions. Nevertheless, for GC/Nf/CNT/CoTRP, the increase in the current is remarkable. The GC/Nf/CoTRP modified electrode gave no significant analitycal signal for hydrogen peroxide reduction. Moreover, a great increase in current is observed with GC/Nf/CNT/CoTRP at ?150mV which suggests a significant increase in the sensitivity of the modified electrode. Scanning electrochemical microscopy (SECM) revealed an enhancement in the electroactivity of the GC/Nf/CNT/CoTRP modified electrode. This fact has been explained in terms of enhanced homogeneity of the electrodic surface as a consecuence of better dispersibility of CNT‐CoTRP produced by a Nafion polyelectrolyte.     

Ag/IrO_x-pH电极的制备、性能及应用研究

报道了一种基于Ag丝电化学修饰IrOx制备Ag/IrOx-pH电极的方法. 电极线性范围2～12pH, 响应斜率-73 mV/pH, 响应时间＜35 s. 用于实际样品与pH玻璃电极对照, ΔpH≤0.05, 拓展了可直接测定糊状物、半固体、土壤等pH的领域.     

Electrochemically regenerative visible light-induced reactivity of α-Fe2O3 films with Ag(core)–AgCl(shell) microcrystal composites

Ag(core)–AgCl(shell) microcrystal composites (Ag@AgCl) have been formed on an α-Fe₂O₃ film-coated SnO₂ electrode by a 2 step method consisting of the electrochemical reduction of Ag⁺ ions and the subsequent electrochemical oxidation. The synergy of α-Fe₂O₃ and Ag@AgCl gave rise to a high visible light-induced reactivity (λ_ex > 420 nm) for the oxidation of 2-naphthol (2-NAP) used as a model water pollutant in the presence and absence of oxygen. These findings were attributable to the function of Ag@AgCl composites as an excellent charge-separation promoter and built-in acceptor.     

Effect of Various Deposition Techniques,Electrode Materials and Posttreatment with Tetrabutylammonium and Tetrabutylphosphonium Salts on the Electrochemical Behavior and Stability of Various Prussian Blue Modified Electrodes

The effect of various deposition techniques, electrode materials and posttreatment with tetrabutylammonium and tetrabutylphosphonium salts on the electrochemical behavior and stability of various Prussian blue (PB) modified electrodes, namely PB modified glassy carbon electrodes, silicate‐film supported PB modified glassy carbon electrodes, PB‐doped silicate glassy carbon electrodes, PB modified carbon ceramic electrodes using electrochemical deposition and PB modified carbon ceramic electrodes using chemical deposition is reported. Cyclic voltammetry and amperometric measurements of hydrogen peroxide were performed in a flow injection system while the carrier phosphate buffer (pH 7.0) with a flow rate of 0.8 mL min^?1 was propelled into the electrochemical flow through cell housing the PB modified working electrode as well as an Ag|AgCl|0.1 M KCl reference and a Pt auxiliary electrode. The results showed that the deposition procedure, electrode material and posttreatment with additional chemicals can significantly alter the stability and electrochemical behavior of the PB film. Among the studied PB modified electrodes, those based on carbon ceramic electrodes modified with a film of electropolymerized PB showed the best electrochemical stability.