The Fabrication and Characterization of a Nickel Nanoparticle Modified Boron Doped Diamond Electrode for Electrocatalysis of Primary Alcohol Oxidation

We report the fabrication of a Ni nanoparticle modified BDD electrode and its application in the electrocatalysis of primary alcohol electrooxidation. Modification was achieved via electrodeposition from Ni(NO₃)₂ dissolved in sodium acetate solution (pH 5). Characterization of the Ni‐modified BDD (Ni‐BDD) was performed using ex situ atomic force microscopy (AFM) and high resolution scanning electron microscopy (SEM) coupled with energy dispersive X‐ray spectroscopy (EDX). Large nanoparticles of nickel were observed on the BDD surface ranging 5 to 690 nm in height and 0.18 μm^?3 in volume, and an average number density of ca. 13×10⁶ nanoparticles cm^?2 was determined. The large range of sizes suggests progressive rather than instantaneous nucleation and growth. Electrocatalysis of ethanol and glycerol, was conducted in an alkaline medium using an unmodified BDD, Ni‐BDD and a bulk Ni macro electrode. The Ni‐BDD electrode gave the better electrocatalytic performance, with glycerol showing the greatest sensitivity. Linear calibration plots were obtained for the ethanol and glycerol additions over concentration ranges of 2.8–28.0 mM and 23–230 μM respectively. This gave an ethanol limit of detection of 1.7 mM and sensitivity of 0.31 mA/M, and the glycerol a limit of detection of 10.3 μM with a sensitivity of 35 mA/M.     

Electrochemical Detection of Catechol on Boron‐doped Diamond Electrode Modified with Au/TiO2 Nanorod Composite

Au/TiO₂ nanorod composites with different ratios of [TiO₂]:[Au] have been prepared by chemically reducing AuCl₄^‐ on the positively charged TiO₂ nanorods surface and used to modify boron‐doped diamond (BDD) electrodes. The electrochemical behaviors of catechol on the bare and different Au/TiO₂ nanorod composites‐modified BDD electrodes are studied. The cyclic voltammetric results indicate that these different Au/TiO₂ nanorod composites‐modified BDD electrodes can enhance the electrocatalytic activity toward catechol detection, as compared with the bare BDD electrode. Among these different conditions, the Au/TiO₂‐BDD3 electrode (the ratio of [TiO₂]:[Au] is 27:1) is the most choice for catechol detection. The electrochemical response dependences of the Au/TiO₂‐BDD3 electrode on pH of solution and the applied potential are studied. The detection limit of catechol is found to be about 1.4 × 10^‐6 M in a linear range from 5 × 10^‐6 M to 200 × 10^‐6 M on the Au/TiO₂‐BDD3 electrode.     

The Fabrication and Characterization of a Bismuth Nanoparticle Modified Boron Doped Diamond Electrode and Its Application to the Simultaneous Determination of Cadmium(II) And Lead(II)

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by square‐wave anodic stripping voltammetry (SWASV) using a bismuth nanoparticle modified boron doped diamond (Bi‐BDD) electrode. Bi deposition was performed in situ with the analytes, from a solution of 0.1 mM Bi(NO₃)₃ in 0.1 M HClO₄ (pH 1.2), and gave detection limits of 1.9 μg L^?1 and 2.3 μg L^?1 for Pb(II) and Cd(II) respectively. Pb²⁺ and Cd²⁺ could not be detected simultaneously at a bare BDD electrode, whilst on a bulk Bi macro electrode (BiBE) the limits of detection for the simultaneous determination of Pb²⁺ and Cd²⁺ were ca. ten times higher.     

Electrochemical detection of ascorbic acid and serotonin at a boron-doped diamond electrode modified with poly(N,N-dimethylaniline)

The electrochemical oxidation of ascorbic acid (AA) and serotonin (5-HT) at a boron-doped diamond (BDD) electrode modified with poly(N,N-dimethylaniline) (PDMA) has been studied. The oxidation potentials of 5-HT and AA overlapped after mixing of the two chemicals, due to interference of AA at the bare BDD electrode. However, after modifying the BDD electrode with a cationic polymer (PDMA), the oxidation peaks of 5-HT and AA were separated. PDMA-coated BDD electrodes can be used for simultaneous detection of these species.     

A Nitrite Electrochemical Sensor Based on Boron‐Doped Diamond Planar Electrochemical Microcells Modified with a Monolacunary Silicotungstate Polyoxoanion

A new boron doped diamond microcells (BDD) was modified, for rapid, selective and highly sensitive determination of nitrite, using a coating film of polyoxometalates (POMs), formed by cyclic voltammetry on the molecular p‐phenylenediamine (PPD) functionalized BDD. The scanning electron microscopy (SEM) technique was used to examine the morphology of (PPD/SiW₁₁) modified (BDD) electrode. It was found that (SiW₁₁) layer was uniformly formed on the electrode surface. It was observed that (BDD/PPD/SiW₁₁) showed excellent electrocatalytic activities towards nitrite ion. Under the selected conditions, the anodic peak maximum at ?0.6 V was linear versus nitrite concentration in the 40 µM–4 mM range, and the detection limit obtained was 20 µM. The newly developed electrode has been successfully applied to the determination of nitrite content in real river water samples.     

The Determination of Methanol Using an Electrolytically Fabricated Nickel Microparticle Modified Boron Doped Diamond Electrode

A nickel modified boron doped diamond (Ni‐BDD) electrode and nickel foil electrode were used in the determination of methanol in alkaline solutions. The Ni‐BDD electrode was electrodeposited from a 1 mM Ni(NO₃)₂ solution (pH 5), followed by repeat cycling in KOH. Subsequent analysis utilised the Ni(OH)₂/NiOOH redox couple to electrocatalyse the oxidation of methanol. Methanol was determined to limits of 0.3 mM with a sensitivity of 110 nA/mM at the Ni‐BDD electrode. The foil electrode was less sensitive achieving a limit of 1.6 mM and sensitivity of 27 nA/mM. SEM analysis of the electrodes found the Ni‐BDD to be modified by a quasi‐random microparticle array.     

On the Utilization of Boron Doped Diamond Electrode as a Sensor for Parathion and as an Anode for Electrochemical Combustion Of Parathion

This work proposes the utilization of a boron doped diamond (BDD) electrode as a sensor for pesticides and as well as an anode for electrochemical combustion of Parathion in spiked, pure and natural waters. The square‐wave voltammetry was selected as the electroanalytical technique and the Britton–Robinson buffer as the electrolyte. The electrochemical reduction responses of Parathion were analyzed and compared with those previously obtained using a hanging mercury electrode (HMDE). The detection and quantification limits were calculated from the analytical curves both for BDD and HMDE in Milli‐Q water (2.4 and 7.9 μg L^?1 and 3.9 and 12.8 μg L^?1 respectively) showing only a slight improvement when used BDD. However, if the application involves polluted natural waters the improvement is accentuated due to the very low adsorption characteristics of BDD, which prevent the fouling of electrode surface by organic pollutants. The BDD was also used as anode for electrochemical remediation of Parathion contamination. In this case, electrolysis was carried out in high positive potential (3.0 V) and lead the electrochemical combustion of Parathion to CO₂ and H₂O, as measured by the diminishing of total organic carbon in the electrolyte.     

Comparison of Boron‐Doped Diamond and Glassy Carbon Electrodes for Determination of Procaine Hydrochloride

The electrochemical oxidation of procaine hydrochloride (PC?HCL, 2‐diethylaminoethyl 4‐aminobenzoate hydrochloride) was investigated at as‐deposited boron‐doped diamond (ad‐BDD) electrode, anodically oxidized BDD (ao‐BDD) electrode and glassy carbon (GC) electrode using cyclic voltammetry (CV). Well‐defined cyclic voltammograms were obtained for PC?HCL oxidation with high signal‐to‐background (S/B) ratio, low tendency for adsorption, good reproducibility and long‐term stability at ad‐BDD electrode, demonstrating its superior electrochemical behavior and significant advantages in contrast to ao‐BDD and GC electrode. At 100 μM PC?HCL, the voltammetric S/B ratio was nearly one order of magnitude higher at an ad‐BDD electrode than that at a GC electrode. In a separate set of experiments for oxidation of 100 μM PC?HCL, 96%, 92% and 84% of the initial oxidation peak current was retained at the ad‐BDD, ao‐BDD and GC electrode, respectively, by stirring the solution after the tenth cycle. The current response was linearly proportional to the square root of the scan rate within the range 10–1000 mV s^?1 in 10 μM PC?HCL solutions, indicating that the oxidation process was diffusion‐controlled with negligible adsorption at an ad‐BDD surface. The good linearity was observed for a concentration range from 5 to 200 μM with a linear equation of y=0.03517x+0.65346 (r=0.999), and the detection limit was 0.5 μM for oxidation of PC?HCL at the ad‐BDD electrode. The ad‐BDD electrode could maintain 100% of its original activity after intermittent use for 3 months.     

Further Study of CO2 Electrochemical Reduction on Palladium Modified BDD Electrode: Influence of Electrolyte

The study of CO₂ electrochemical reduction to useful compounds using bare or modified BDD electrode attracts numerous attentions. Meanwhile, the efficiency of products obtained from CO₂ electrochemical reduction is known to be determined by the electrode material and the electrolyte. Formic acid as main product and CO as a minor product, have also been known on the CO₂ reduction using BDD electrode. Recently, we reported the successful improvement of CO production from the reduction of CO₂ by decorating the surface of BDD electrode with palladium particles. Following this, herein, we present further investigation on electrolyte dependence, including cation and anion dependence and also concentration effect in order to understand deeply the CO₂ reduction on surface of palladium modified BDD electrode. The results suggest the use of NaCl and KCl as a catholyte for optimum performance, in addition to the improvement of CO₂ reduction product in higher electrolyte concentration.     

A novel paper-based device coupled with a silver nanoparticle-modified boron-doped diamond electrode for cholesterol detection

A novel paper-based analytical device (PAD) coupled with a silver nanoparticle-modified boron-doped diamond (AgNP/BDD) electrode was first developed as a cholesterol sensor. The AgNP/BDD electrode was used as working electrode after modification by AgNPs using an electrodeposition method. Wax printing was used to define the hydrophilic and hydrophobic areas on filter paper, and then counter and reference electrodes were fabricated on the hydrophilic area by screen-printing in house. For the amperometric detection, cholesterol and cholesterol oxidase (ChOx) were directly drop-cast onto the hydrophilic area, and H₂O₂ produced from the enzymatic reaction was monitored. The fabricated device demonstrated a good linearity (0.39 mg dL⁻¹ to 270.69 mg dL⁻¹), low detection limit (0.25 mg dL⁻¹), and high sensitivity (49.61 μA mM⁻¹ cm⁻²). The precision value for ten replicates was 3.76% RSD for 1 mM H₂O₂. In addition, this biosensor exhibited very high selectivity for cholesterol detection and excellent recoveries for bovine serum analysis (in the range of 99.6–100.8%). The results showed that this new sensing platform will be an alternative tool for cholesterol detection in routine diagnosis and offers the advantages of low sample/reagent consumption, low cost, portability, and short analysis time.     

Pt-polyaniline nanocomposite on boron-doped diamond electrode for amperometic biosensor with low detection limit

Boron-doped diamond electrodes covered with a nanostructured Pt nanoparticle-polyaniline composite have been fabricated and employed as sensitive amperometric sensors with low detection limit. A highly conductive boron-doped diamond thin film (BDD) was prepared by chemical vapor deposition, and its morphology was characterized by scanning electron microscopy and transmission electron microscopy. The nanostructured composite layer was grown on the BDD electrode by electrochemical deposition of polyaniline and Pt nanoparticles. Glucose oxidase (GOx) was then adsorptively immobilized on the modified BDD electrode. The biosensor displays a large surface area, high catalytic activity of the Pt nanoparticles, efficient electron mediation through the conducting polymer, and low background current of the electrode. The biosensor exhibits an excellent response to glucose, with a broad linear range from 5.9 μM to 0.51 mM, a sensitivity of 5.5 μA·mM^?1, a correlation coefficient (R) of 0.9947, and a detection limit of 0.10 μM. The apparent Michaelis-Menten constant (K _M ^app ) and the maximum current density of the electrode are 4.1 mM and 0.021 mA, respectively. This suggests that the immobilized GOx possesses a higher affinity for glucose at the lower K _M ^app , and that the enzymatic reaction rate constitutes the rate-limiting step of the response.     

Comparison of the performances of Ti/SnO2-Sb, Ti/SnO2-Sb/PbO2, and Nb/BDD anodes on electrochemical degradation of azo dye

In this paper, the preparation conditions of antimony-doped SnO₂ and PbO₂ electrode were optimized for the degradation activity of AO7 dye solution. The results showed that when the doping content of Sb is 8 mol %(SnO₂-Sb(0.08)), the SnO₂ electrode exhibited best activities for the decolorization and mineralization of AO7. The concentration of NaF in electroplating solution had a noticeable effect on PbO₂ electrode for the decolorization of AO7 solution, but little influence on the COD removal rate. The anodic stability tests showed that the electrode prepared in the solution containing 0.10 g l⁻¹ NaF (PbO₂-F(0.10)) was best for environmental application. The comparison of SnO₂-Sb(0.08), PbO₂-F(0.10) and Boron-doped Diamond (BDD) electrodes revealed that a more rapid decolorization rate was obtained on SnO₂-Sb(0.08) and PbO₂-F(0.10) electrodes in dilute AO7 solutions, while higher COD removal rate of concentrated AO7 solutions was on BDD and SnO₂-Sb(0.08) electrodes. The effect of concentration of Na₂SO₄ on the degradation rate of AO7 was very notable on BDD electrode for its highest overpotential of oxygen evolution reaction. In the chloride-containing medium, the decolorization was accelerated greatly but the completed mineralization of AO7 was inhibited with the increasing of chloride ions concentration when these high-overvoltage anodes were used Published in Russian in Elektrokhimiya, 2008, vol. 44, No. 7, pp. 865–875. The text was submitted by the authors in English.     

Electroanalytical Determination of Cadmium(II) and Lead(II) Using an Antimony Nanoparticle Modified Boron‐Doped Diamond Electrode

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by linear sweep anodic stripping voltammetry (LSASV) using an antimony nanoparticle modified boron doped diamond (Sb‐BDD) electrode. Sb deposition was performed in situ with the analytes, from a solution of 1 mg L^?1 SbCl₃ in 0.1 M HCl (pH 1). Pb²⁺ inhibited the detection of Cd²⁺ during simultaneous additions at the bare BDD electrode, whereas in the presence of antimony, both peaks were readily discernable and quantifiable over the linear range 50–500 μg L^?1.     

Electrochemical oxidation of 3-methylpyridine at a boron-doped diamond electrode: application to electroorganic synthesis and wastewater treatment

The electrochemical oxidation of 3-methylpyridine (3-MP) at synthetic boron-doped diamond (BDD) thin film electrode has been studied in acid media by cyclic voltammetry and bulk electrolysis. The results have shown that in the potential region of water stability there can occur direct electron transfer reactions on BDD surface that result in electrode fouling due to the formation of a polymeric film on its surface. While during electrolyses in the potential region of water decomposition, indirect oxidation reactions can take place by electrogenerated active intermediates, probably hydroxyl radicals that can avoid electrode fouling. Depending on the values of applied current density, it is possible to obtain the partial oxidation of 3-MP to nicotinic acid or the complete combustion of 3-MP to CO₂.     

Polymer‐coated Boron Doped Diamond Optically Transparent Electrodes for Spectroelectrochemical Sensors

Spectroelectrochemical sensors combine electrochemistry, spectroscopy, and partitioning into a film to provide improved selectivity for the target analyte. The sensor usually consists of an optically transparent electrode (OTE) coated with a charge selective polymer film. The polymer film is chosen to pre‐concentrate analyte at the OTE surface to improve the sensitivity and provide selectivity against like charged interferences. OTEs such as Indium Tin Oxide (ITO) have been used extensively for spectroelectrochemical sensors, but little is known about the applicability of such sensors using other OTE materials, such as Boron Doped Diamond (BDD). One distinct advantage of BDD OTEs over ITO OTEs is their significant increase in sensitivity for organic compounds, such as 4‐aminophenol and hydroquinone. We have developed absorption and fluorescence‐based sensing methods with a BDD OTE coated with a sulfonated ionomer film, Nafion. This is demonstrated with tris(2,2′‐bipyridyl)ruthenium(II) ion [Ru(bpy)₃²⁺] using an attenuated total reflectance (ATR) flow cell setup for both absorption and fluorescence. With a Nafion coated BDD optically transparent thin layer electrode (OTTLE), we developed a fluorescence based sensor for a common polyaromatic hydrocarbon (PAH), 1‐hydroxypyrene (1‐pyOH), achieving a detection limit of 80 nM (17 ppb). This work manifests new sensing applications while broadening the use of spectroelectrochemistry, OTEs, and BDD as an electrode material.     

Electrochemical Behavior and Electroanalytical Determination of Indole‐3‐Acetic Acid Phytohormone on a Boron‐Doped Diamond Electrode

In this work, a boron‐doped diamond (BDD) electrode was used for the electroanalytical determination of indole‐3‐acetic acid (IAA) phytohormone by square‐wave voltammetry. IAA yielded a well‐defined voltammetric response at +0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer, pH 2.0. The process could be used to determine IAA in the concentration range of 5.0 to 50.0 µM (n=8, r=0.997), with a detection limit of 1.22 µM. The relative standard deviation of ten measurements was 2.09 % for 20.0 µM IAA. As an example, the practical applicability of BDD electrode was tested with the measurement of IAA in some plant seeds.     

Fabrication and characterization of boron doped diamond microelectrode arrays of varied geometry

Boron doped diamond (BDD) is a well-known electrode material that exhibits an excellent electrochemical potential window with very low background current. With this, microelectrodes and microelectrode arrays (MEAs) have been found to even further lower background currents without compromising sensitivity. As such, BDD MEAs are excellent electrode materials for a variety of electroanalytical applications, capable of multi-mode detection. We fabricated BDD MEAs adapting traditional semiconductor microfabrication processes; the resulting MEAs were patterned in different geometries to find an optimum electrochemical response, depending on the application. This is demonstrated using 4 different MEA geometries of different size and spacing using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), where the charge transfer resistance (R_ct) increases as the electrodes are farther spaced from one another. Excellent sigmoidal voltammogram shape in CV was obtained for each BDD MEA geometry. BDD MEAs spaced farther from one another were found to give better resolution from the background in fast scan cyclic voltammetric measurements of dopamine due to the decrease in the double layer capacitance (C_dl) as verified with EIS. This work furthers the understanding of BDD MEAs and their pertinence to sensitive electroanalytical techniques.     

Development of an amperometric biosensor based on covalent immobilization of tyrosinase on a boron-doped diamond electrode

An amperometric enzyme electrode based on direct covalent immobilization of tyrosinase on a boron-doped diamond (BDD) electrode has been developed for the detection of phenolic compounds. Combined chemical and electrochemical modifications of the BDD film with 4-nitrobenzenediazonium tetrafluoroborate, an aminophenyl-modified BDD (AP–BDD) surface was produced, and then the tyrosinase was covalently immobilized on the BDD surface via carbodiimide coupling. The response dependences of the enzyme electrode (Tyr–AP–BDD electrode) on pH of solution, applied potential, oxygen level and phenolic compounds diffusion were studied. The Tyr–AP–BDD electrode shows a linear response range of 1–200, 1–200 and 1–250 μM and sensitivity of 232.5, 636.7 and 385.8 mA M⁻¹ cm⁻² for phenol, p-cresol and 4-chlorophenol, respectively. 90 percent of the enzyme activity of the Tyr–AP–BDD electrode is retained for 5 weeks storing in 0.1 M PBS (pH 6.5) at 4 °C.     

Selective Determination of Verapamil in Pharmaceutics and Urine Using a Boron‐doped Diamond Electrode Coupled to Flow Injection Analysis with Multiple‐pulse Amperometric Detection

This work presents a simple and low‐cost method for fast and selective determination of Verapamil (VP) in tablets and human urine samples using a boron‐doped diamond working electrode (BDD) coupled to a flow injection analysis system with multiple pulse amperometric detection (FIA‐MPA). The electrochemical behaviour of VP in 0.1 mol L⁻¹ sulfuric acid showed three merged oxidation peaks at around +1.4 V and upon reverse scan, one reduction peak at 0.0 V (vs. Ag/AgCl). The MPA detection was performed applying a sequence of three potential pulses on BDD electrode: (1) at +1.6 V for VP oxidation, (2) at +0.2 V for reduction of the oxidized product and (3) at +0.1 V for cleaning of the working electrode surface. The FIA system was optimized with injection volume of 150 μL and flow rate of 3.5 mL min⁻¹. The method showed a linear range from 0.8 to 40.0 μmol L⁻¹ (R>0.99) with a low limit of detection of 0.16 μmol L⁻¹, good repeatability (RSD<2.2 %; n=10) and sample throughput (45 h⁻¹). Selective determination of VP in urine was performed at+0.2 V due to absence of interference from ascorbic and uric acids in this potential. The addition‐recovery tests in both samples were close to 100 % and the results were similar to an official method.     

Electroanalysis of myoglobin and hemoglobin with a boron-doped diamond electrode

The electrochemical behavior of myoglobin (Mb) and hemoglobin (Hb) was investigated with a boron-doped diamond (BDD) electrode by cyclic voltammetry. In acetate buffer solutions, the oxygen reduction at the BDD electrode showed a very high overpotential while the reduction of Mb or Hb was observed in the more positive potential region. Owing to the electrocatalytic reaction of O₂ and the participation of H⁺ following the electrochemical reduction of ferric proteins, the voltammetric responses for Mb and Hb on the BDD electrode in the negative going scans became remarkable in acidic buffer solutions in air. The peak current was linearly proportional to the concentration of Mb in the range 1×10⁻⁶–2×10⁻⁵ M or the concentration of Hb from 1×10⁻⁶ to 1×10⁻⁵ M.