Non-enzymatic Glucose Sensor Based on Porous Foam Au/MXene Nanocomposites

A novel electrochemical non-enzymatic glucose sensor based on three-dimensional Au/MXene nanocomposites was developed. MXenes were prepared using the mild etched method, and the porous foam of Au nanoparticles was combined with the MXene by means of in situ synthesis. By controlling the mass of MXene in the synthesis process, porous foam with Au nanoparticles was obtained. The three-dimensional foam structure of nanoparticles was confirmed by scanning electron microscopy. Cyclic voltammetry and electrochemical impedance spectroscopy were used to study the electrochemical performance of the Au/MXene nanocomposites. The Au/MXene nanocomposites acted as a fast redox probe for non-enzymatic glucose oxidation and showed good performance, including a high sensitivity of 22.45 μA\begin{document}$\cdot$\end{document}(mmol/L)\begin{document}$^{-1}$\end{document}\begin{document}$\cdot$\end{document}cm\begin{document}$^{-1}$\end{document} and a wide linear range of 1-12 mmol/L. Studies have shown that MXene as a catalyst-supported material is beneficial to enhance the conductivity of electrons and increase the loading rate of the catalyst materials. The foam structure with Au nanoparticles can provide a larger surface area, increase the contact area with the molecule in the catalytic reaction, and enhance the electrochemical reaction signal. In summary, this study shows that Au/MXene nanoparticles have the potential to be used in non-enzymatic glucose sensors.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

Electrochemical Sensor Based on a Novel Pt−Au Bimetallic Nanoclusters Decorated on Reduced Graphene Oxide for Sensitive Detection of Ofloxacin

Pt−Au nanoclusters decorated on the surface of reduced graphene oxide (rGO/Pt−Au) was facilely prepared by one‐pot electrochemical reduction. The morphology and composition of rGO/Pt−Au composites had been characterized by scanning electron microscopy (SEM) coupled with energy‐dispersive X‐ray spectrometry (EDX), fourier transform‐infrared spectroscopy (FT‐IR) and electrochemical methods. Ofloxacin is a member of synthetic quinolones which has been widely used for the treatment of common diseases in humans and animals. The performance of the rGO/Pt−Au nanocomposite toward the oxidation of ofloxacin was compared with the other similar nanostructures like rGO/Pt and rGO/Au. In the optimized conditions, two linear calibration curves were obtained, from 0.08 to 10 μM and 10 to 100 μM ofloxacin. A detection limit of 0.05 μM ofloxacin was observed at pH 5.7 for the GCE/rGO/Pt−Au. The proposed sensor was successfully applied to determine ofloxacin in tablets and human urine samples and the results were satisfactory.     

A Highly Sensitive Nonenzymatic Glucose Sensor Based on Carbon Electrode Amplified with PdxCuy Catalyst

Approximately global Pd and Pd₉₄Cu₆ alloy nano catalysts of average diameter 10.5 and 5.9 nm respectively, have been synthesized hydrothermally by wet chemical reduction and co-reduction methods without addition of any capping agent. X-ray diffraction and various microscopic studies are used to characterize the crystal phase and the morphology of the catalysts. Non-enzymatic amperometric glucose sensors based on these synthesized catalyst materials are tested and compared in alkali at different potentials by cyclic voltammetry and chronoamperometry. The sensors characterized by fixed potential chronoamperometry are found to be sufficiently sensitive to glucose at different negative potentials like −0.65 V, −0.40 V, −0.10 V with respect to Hg/HgO electrode (E⁰≈0.1 V), where the reactions of glucose oxidation are different. The sensor constructed with Pd₉₄Cu₆ nanocatalyst shows an outstanding sensitivity of 10.1 mA cm⁻² mM⁻¹ which is considerably higher than that constructed with similarly synthesized Pd nanoparticles at any potential and that found in the literature of Pd based glucose sensors. The lower detection limit and response time obtained with Pd₉₄Cu₆ nanoparticles are 10 μM and 3 s respectively. These sensors also exhibit high specificity to glucose and significant anti-interference property against some common species like ascorbic acid (AA), uric acid (UA) and some monosaccharides whose interfering effects are found to decrease with decrease of potential of glucose oxidation. The electrocatalytic ability of the synthesized Pd and Pd₉₄Cu₆ nanoparticles toward glucose oxidation has also found promising in blood sample at different potentials.     

Highly Sensitive Nonenzymatic Glucose Sensor Based on 3D Ultrathin NiFe Layered Double Hydroxide Nanosheets

As a promising electrode material, Ni‐based nanomaterials exhibit a remarkable electrochemical catalytic activity for nonenzymatic glucose sensors. In this paper, Nickel–Iron layered double hydroxide (NiFe‐LDH) film electrode with ultrathin nanosheets and porous nanostructures was synthesized directly on Ni foam (NF) by a one‐step hydrothermal method. The as‐obtained NiFe‐LDH electrode was adopted for glucose detection without further treatment. As an integrated binder‐free electrode for glucose sensor, the NiFe‐LDH/NF hybrid exhibits a superior sensitivity of 3680.2 μA mM⁻¹ cm⁻² with a low limit of detection (0.59 μM, S/N=3) as well as fast response time (<1 s). An excellent selectivity from potential interference species such as ascorbic acid, uric acid and Cl⁻ ions and acceptable stability were also achieved. The outstanding performance can be ascribed to the abundant electrochemistry active sites, facilitative diffusion of the electrolyte, high electron transfer rate and reliable stability architecture. Therefore, the NiFe‐LDH nanosheets demonstrate potential application in non‐enzymatic sensory of glucose.     

A Sensitive Sensor Based on CuTSPc and Reduced Graphene Oxide for Simultaneous Determination of the BHA and TBHQ Antioxidants in Biodiesel Samples

A novel and sensitive electrochemical sensor was developed for the simultaneous determination of the butylated hydroxyanisole (BHA) and tert‐butylhydroquinone (TBHQ) antioxidants in biodiesel samples employing the differential pulse voltammetry (DPV). In this sense, a glassy carbon electrode (GCE) modified with copper (II) tetrasulfonated phthatocyanine immobilized on reduced graphene oxide (CuTSPc/rGO) allowed the detection of BHA and TBHQ at potentials lower than those observed at unmodified electrodes. The sensor was characterized by cyclic voltammetry (CV) and linear scan voltammetry (LSV). After optimization of the experimental parameters, the analytical curves for simultaneous determination of BHA and TBHQ by DPV technique demonstrated an excellent linear response from 0.1 to 500 µmol L^?1 with detection limit of 0.045 µmol L^?1 for TBHQ and 0.036 µmol L^?1 for BHA. Finally, the proposed method was successfully applied in the simultaneous determination of BHA and TBHQ in six biodiesel samples, and the results obtained were found to be similar to those obtained using the HPLC method with agreement at 95 % confidence level.     

高灵敏检测葡萄糖的新型荧光纳米传感器

构建了一种用于高灵敏检测葡萄糖的新型荧光纳米传感器.在辣根过氧化物酶(HRP)的催化下,H2O2氧化3,3′,5,5′-四甲基联苯胺(TMB),生成具有强吸光性质的TMB多聚体,导致1-氧-1H-非那烯-2,3-二腈(1-Oxo-1H-phenalene-2,3-dicarbonitrile, OPD)分子的荧光发生淬灭,基于此实现H2O2的定量检测,线性范围分别为0.05~0.80 μmol/L和1~10 μmol/L,检出限(3σ)为0.02 μmol/L.由于葡萄糖氧化酶(Gox)可催化葡萄糖分解产生H2O2,基于此可以实现葡萄糖分子的定量检测,线性范围分别为0.1~3.0 μmol/L和4.0~30 μmol/L, 检出限(3σ)为0.02 μmol/L.将本方法用于实际血清样品中葡萄糖的定量检测,结果与临床检测结果相符.     

氧化石墨烯/多壁碳纳米管负载金铂核壳纳米粒子构建一种三维新型抗坏血酸电化学传感器

该文采用涂覆的方式构建了一种用于灵敏检测抗坏血酸(AA)的电化学传感器。先将多壁碳纳米管(MWCNTs)和氧化石墨烯(GO)混合悬浮液修饰在玻碳电极(GCE)表面,修饰的GO可有效防止MWCNTs聚集,再将具有良好电催化性能的金铂核壳纳米粒子(Au@Pt NPs)修饰在GO/MWCNTs电极上,层层组装构建形成GO/MWCNTs/Au@Pt NPs/GCE三维新型抗坏血酸电化学传感器。该修饰电极在磷酸缓冲溶液中对AA显示了较宽的线性范围和极低的检出限,氧化峰电流与AA浓度在0.005～0.5μmol/L和0.5～1 000μmol/L范围内呈良好的线性关系,相关系数均为0.999,检出限(S/N=3)为4×10~(-9) mol/L,稀释人体血清样品的加标浓度为0.01、0.1、10μmol/L,回收率为90.9%～108%,相对标准偏差(RSD,n=3)为1.2%～2.8%。该修饰电极对AA具有良好的选择性,可有效排除多巴胺、尿酸、葡萄糖等生物小分子的干扰。方法简单、高效、灵敏,可用于临床实际检测。     

A Highly Sensitive and Selective Non-enzymatic Hydrogen Peroxide Sensor Based on Nanostructured Co3O4 Thin Films Using the Sol-gel Method

In this work we report an easy and efficient way to fabricate nanostructured cobalt oxide (Co₃O₄) thin films as a non-enzymatic sensor for H₂O₂ detection. Co₃O₄ thin films were grown on ITO glass substrates via the sol-gel method and characterized with several techniques including X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and optical absorbance. The Co₃O₄ thin films’ performance regarding hydrogen peroxide detection was studied in a 0.1 M NaOH solution using two techniques, cyclic voltammetry (CV) and amperometry. The films exhibited a high sensitivity of 1450 μA.mM⁻¹.cm⁻², a wide linear range from 0.05 μM to 1.1 mM, and a very low detection limit of 18 nM. Likewise, the Co₃O₄ thin films produced showed an exceptional stability and a high selectivity.     

A Review of Glucose Biosensors Based on Graphene/Metal Oxide Nanomaterials

In recent years, considerable attention has been paid to developing economical yet rapid glucose sensors using graphene and its composites. Recently, the excellent properties of graphene and metal oxide nanoparticles have been combined to provide a new approach for highly sensitive glucose sensors. This review focuses on the development of graphene functionalized with different nanostructured metal oxides (such as copper oxide, zinc oxide, nickel oxide, titanium dioxide, iron oxide, cobalt oxide, and manganese dioxide) for use as glucose biosensors. Additionally, a brief introduction of the electrochemical principles of glucose biosensors (including amperometric, potentiometric, and conductometric) is presented. Finally, the current status and future prospects are outlined for graphene/metal oxide nanomaterials in glucose sensing.     

基于聚多巴胺/铜微粒自组装多层膜的无酶葡萄糖传感器

利用多巴胺易于在电极表面发生自聚反应,且聚多巴胺膜中富含邻苯二酚等反应性基团,可通过二次反应实现电极表面的进一步功能化修饰的特点,在玻碳电极(GCE)表面,将多巴胺自聚膜(PDA)与铜微粒(Cu)进行层-层自组装,构建了无酶葡萄糖电化学传感器(GCE/(PDA/ Cu) n )。传感器的灵敏度可通过控制多层膜的组装层数进行调控。采用紫外-可见光谱跟踪表征了多层膜的组装过程,结果表明,多层膜的生长是逐步且均匀的过程。采用循环伏安法和电流-时间曲线法研究了修饰电极对葡萄糖的电催化氧化性能。对于GCE/(PDA/ Cu)4,检测葡萄糖的线性范围为0.5~9.0 mmol/ L,检出限为5.8μmol/ L(S/ N=3)。本传感器具有良好的重现性、稳定性和较强的抗干扰能力。将本传感器用于血清中葡萄糖的测定,结果令人满意。     

A Novel Amperometric Nitric Oxide Sensor Based on Polythionine / Nation Modified Glassy Carbon Electrode

A novel amperometric sensor for the determination of nitric oxide was developed by coating polythionine / nafion on a glassy carbon electrode. This sensor exhibited a great enhancement to the oxidation of nitric oxide. The oxidation peak currents were linear to the concentration of nitric oxide over the wide range from 3.6×10-7 to 6.8×10-5 mol.L-1, and the detection limit was 7.2×10-8 mol.L-1. Experimental results showed that this nitric oxide sensor possessed excellent selectivity and longer stability. NO releasing from rat kidney was monitored by this sensor.     

Nonenzymatic Electrochemical Glucose Sensor Based on Novel Copper Film

Novel copper (Cu) film composed of pillar‐like structure was synthesized on indium‐doped tin oxide (ITO) substrate by electrodeposition in acetate bath with proline as additive for the first time and used to construct nonenzymatic glucose sensor. When applied to detect glucose, such prepared electrode showed low operating potential (0.4 V), high sensitivity (699.4499 µA mM⁻¹ cm⁻²), and fast response time (<3 s) compared with other Cu‐based electrodes. In addition, the prepared electrode also offered good anti‐interference ability to ascorbic acid, uric acid and acetaminophen. Present study provides new insights into the control of Cu film morphology for sensor fabrication.     

Preparation of Molecularly Imprinted Electrochemical Sensor for Detection of Vincristine Based on Reduced Graphene Oxide/Gold Nanoparticle Composite Film

An innovative molecularly imprinted electrochemical sensor was fabricated based on reduced graphene oxide (RGO) and gold nanocomposite (Au) for rapid detection of vincristine (VCR). The RGO‐Au composite membrane was obtained via direct one‐step electrodeposition technique of graphene oxide (GO) and chloroauric acid (HAuCl₄) on the surface of a glassy carbon electrode (GCE) by means of cyclic voltammetry (CV) in the potential range between ?1.5 and 0.6 V in phosphate buffer solution (PBS) of pH 9.18, which is capable of effectively utilizing its superior electrical conductivity, larger specific surface area due to its synergistic effect between RGO and Au. The molecularly imprinted polymers (MIPs) were synthesized on the RGO‐Au modified glassy carbon electrode surface with VCR as the template molecular, methyl acrylic acid (MAA) as the functional monomer, and ethylene glycol maleic rosinate acrylate (EGMRA) as a cross‐linker. The performance of the sensor was investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) in detail. Under the optimum conditions, the fabricated sensor exhibited a linear relationship between oxidation peak current and VCR concentration over the range of 5.0×10^?8–5.0×10^?6 mol·L ^minus;1 with a correlation coefficient of 0.9952 and a detection limit (S/N=3) of 2.6×10^minus;8 mol·L^minus;1. The results indicated that the imprinted polymer films exhibited an excellent selectivity for VCR. The imprinted sensor was successfully used to determine VCR in real samples with recoveries of 90% –120% by using the standard addition method.     

Disposable Sandwich‐type Electrochemical Sensor for Selective Detection of Glucose Based on Boronate Affinity

A disposable sandwich‐type electrochemical sensor for selective detection of glucose was established. The primary receptor, 3‐aminophenylboronic acid was grafted covalently onto the surface of screen‐printed carbon electrodes through an in situ‐generated diazo‐reaction. Glucose was first captured by boronic acid group on the electrode, followed by captureing an electroactive ferroceneboronic acid (FcBA) as the secondary receptor to form bidentate glucose‐boronic complex. Electrochemical impedance spectroscopy was applied to characterize the construction of sandwich‐type disposable sensor. In the sandwich assay, current response of captured FcBA on the electrode was dependent on the concentration of glucose. The sandwich assay showed higher selectivity for glucose than that for fructose, mannose, galactose and other electroactive interferences including uric acid, ascorbic acid and dopamine, and exhibited a dynamic concentration range of glucose from 0.5 to 20.0 mmol L⁻¹. The disposable sensor demonstrated a good reproducibility with 2.2 % relative standard deviation (RSD). In addition, the disposable glucose sensor was used in detection of the trace glucose in the clinical urine samples.     

Low-applied Potential Non-enzymatic Glucose Sensor Based on Ultrathin 2-D CuS Nanowall Arrays

The 2-D nanostructure, due to unprecedented physical, electronic, and chemical properties, was widely dedicated to the zooms of electrocatalysis, batteries, supercapacitors, solar cells, photocatalysis and sensing platforms. Herein, we reported a sort of low-applied potential non-enzymatic glucose sensor, which used ultrathin 2-D CuS nanowall arrays (CuS-NWAs) fabricated directly onto fluorine-doped tin oxide glass by potentiostatically deposition approach. Meaningfully, the potentiostatical-deposition time can control precisely the frame of 2-D CuS-NWAs on size and thickness and assist to ferret out the growing mechanization by analyzing the copper valence. Then, CuS-NWAs-based non-enzymatic glucose sensor presented the high sensitivity (2610 μA mM⁻¹ cm⁻²), a low detection of 17 nM, fast respond time (1.5–6.2 s) and low detection limits (2.6–17.7 nM, S/N=3) regardless of an applied potential as low as 0.33 V (vs. Ag/AgCl), attributed to that the 2-D CuS-NWAs offer large active area with numerous exposed active points, a low-resistance electron-shuttling passage and door-opened glucose-diffusion channel. Additionally, it was found that the sensitivity of CuS-NWAs-based non-enzymatic glucose sensors can be optimized by altering electrodeposition duration for CuS-NWAs growth. Confirmedly, the 2-D CuS-NWAs can be promised as a new system for high-performance electrochemical sensors with excellent properties of selectivity, stability and reproducibility.     

Nonenzymatic Electrochemical Glucose Sensor Based on Pt Nanoparticles/Mesoporous Carbon Matrix

A nonenzymatic amperometric sensor for sensitive and selective detection of glucose has been constructed by using highly dispersed Pt nanoparticles supported onto mesoporous carbons (MCs). The Pt nanoparticles/mesoporous carbons (Pt/MCs) composites modified electrode displayed high electrocatalytic activity towards the oxidation of glucose. At an applied potential of 0.1 V, the Pt/MCs electrode has a linear dependence (R=0.996) in the glucose concentration up to 7.5 mM with a sensitivity of 8.52 mA M^?1 cm^?2. The Pt/MCs electrode has also shown highly resistant toward poisoning by chloride ions and without interference from the oxidation of common interfering species.     

Reduced Graphene Oxide/Pt Nanoparticles/Zn‐MOF‐74 Nanomaterial for a Glucose Biosensor Construction

In this study, a new glucose biosensor was fabricated by immobilizing glucose oxidase (GOx) on platinum nanoparticles (Pt NPs) decorated reduced graphene oxide (rGO)/Zn‐MOF‐74 hybrid nanomaterial. Herein, the biosensor fused the advantages of rGO with those of porous Zn‐MOF and conductive Pt NPs. This has not only enlarged the surface area and porosity for the efficient GOx immobilization and faster mass transport, but also provided favorable electrochemical features such as high current density, remarkable electron mobility through metal nanoparticles, and improved electron transfer between the components. The GOx‐rGO/Pt NPs@Zn‐MOF‐74 coated electrode displayed a linear measurement range for glucose from 0.006 to 6 mM, with a detection limit of 1.8 μM (S/N: 3) and sensitivity of 64.51 μA mM^?1 cm^?2. The amperometric response of the enzyme biosensor demonstrated the typical behavior of Michaelis‐Menten kinetics. The obtained satisfying sensitivity and measurement range enabled fast and accurate glucose measurement in cherry juice using the fabricated biosensor. The water‐stable Zn‐MOF‐74 demonstrated higher enzyme loading capacity and can be potent supporting material for biosensor construction.     

Manganese Oxide Nanoparticles/Reduced Graphene Oxide as Novel Electrochemical Platform for Immobilization of FAD and its Application as Highly Sensitive Persulfate Sensor

In this study, manganese oxide nanoparticles/reduced graphene oxide(MnOxNPs/rGO) was used as support for strong immobilization of flavin adenine dinucleotide(FAD). A thin film of rGO cast on the electrode surface, followed by performing electrodeposition of MnOxNPs at applied constant potential of +1.4 V vs. Ag/AgCl for 200 s. Finally, FAD was electrodeposited onto the rGO/MnOxNPs film by potential cycling between 1.0 to ?1.0 V in solution containing 1 mg ml^?1 FAD. Electrochemical properties and catalytic activity of GCE/rGO‐MnOxNPs/FAD toward persulfate (S₂O₈^2?) reduction was investigated. Under optimized condition, the concentration calibration range, detection limit, and sensitivity were 0.1 μM–2 mM, 90 nM and 125.8 nA/μM, respectively, using hydrodynamic amperometry technique.