Electrochemical Behavior and Determination of Rutin at the Copper Nanoparticles-Doped Zeolite A/Graphene Oxide-Modified Electrode

In this work, a novel Cu?zeolite A/graphene modified glassy carbon electrode was applied for the determination of rutin. The Cu?zeolite A/graphene composites were prepared using copper doped zeolite A and graphene oxide as the precursor, subsequently reduced by chemical agents. Based on the Cu?zeolite A/graphene modified electrode, the overpotential of the rutin oxidation was lowered by ~300 mV. Also the proposed Cu?zeolite A/graphene modified electrode showed higher electrocatalytic performance than zeolite A/graphene electrode or graphene modified electrode. The electrochemical behavior of copper incorporated in the zeolite A modified electrode illustrated the adsorption-controlled reaction at the modified electrode. The behavior of electrocatalytic oxidation of rutin at the modified electrode was investigated. The diffusion coefficient of rutin was equal to 4.2 × 10^–7 cm²/s. A linear calibration graph was obtained for rutin over the concentration range of 2.3 × 10^–7–2.5 × 10^–3 M. The detection limit for rutin was 1.2 × 10^–7 M. The RSDs of 10 replicate measurements performed on a single electrode at rutin concentrations between 2.3 × 10^–7–2.5 × 10^–3 M were between 1.1 and 2.1%. Study of the influence of potentially interfering substances on the peak current of rutin showed that the method was highly selective. The proposed electrode was used for the determination of rutin in real samples with satisfactory results.     

Detection of Dexamethasone Sodium Phosphate in Blood Plasma: Application of Hematite in Electrochemical Sensors

We studied sensor application of a graphene oxide and hematite (α‐Fe₂O₃/GO) composite electrode well‐characterized by the SEM and XRD. Through differential pulse voltammetry (DPV), oxidation of dexamethasone sodium phosphate (DSP) was studied at the surface of a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) and the α‐Fe₂O₃/GO composite. The values of the transfer coefficient (α) and the diffusion coefficient (D) of DSP were 0.5961 and 4.71×10^?5 cm² s^?1 respectively. In the linear range of 0.1–50 μM, the detection limit (DL) was 0.076 μM. In the second step, a GCE was modified with α‐Fe₂O₃/GO composite and the DSP measurement step was repeated to analyzed and compare the effects of hematite nanoparticles present on graphene oxide surfaces. According to the results, α and D were 0.52 and 2.406×10^?4 cm² s^?1 respectively and the DL was 0.046 μM in the linear range of 0.1–10.0 μM. The sensor is simple, inexpensive and uses blood serum.     

A New Amperometric Hydrazine Sensor Based on Prussian Blue/Single‐walled Carbon Nanotube Nanocomposites

A slow reaction process has been successfully used to synthesize Prussian blue/single‐walled carbon nanotubes (PB/SWNTs) nanocomposites. Electrochemical and surface characterization by cyclic voltammetry (CV), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV‐vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) confirmed the presence of PB nanocrystallites on SWNTs. PB/SWNTs modified glassy carbon electrode (GCE) exhibits efficient electron transfer ability and high electrochemical response towards hydrazine. The fabricated hydrazine sensor showed a wide linear range of 2.0×10^?6–6.0×10^?3 M with a response time less than 4 s and a detection limit of 0.5 μM. PB/SWNTs modified electrochemical sensors are promising candidates for cost‐effective in the hydrazine assays.     

Evaluation of Reduced Graphene Oxide Modified with Antimony and Copper Nanoparticles for Levofloxacin Oxidation

This work presents, for the first time, the oxidation mechanism of levofloxacin combining electrochemical experiments and molecular modelling techniques. Levofloxacin is one of the most widely used antibiotics in the world. The detection of this antibiotic is important, because it cannot be fully assimilated by the human organism, therefore levofloxacin is considerate a hazardous pollutant for environment. Sensors based on reduced graphene oxide (rGO) modified with antimony and copper nanoparticles (NPs) were synthesized, characterized and evaluated for the electrochemical detection of the levofloxacin. The morphological and electrochemical characterization of the composites confirmed that the rGO was modified with the metallic nanoparticles. Molecular modelling studies were performed applying Density Functional Theory (DFT) approach, which indicated that the mechanism of levofloxacin oxidation is given by the loss of two electrons: one from N14 atom and other from C13 atom of the levofloxacin molecule. The glassy carbon electrode (GCE) modified with the SbNPs/rGO and CuNPs/rGO composites were evaluated for the determination of levofloxacin using differential pulse voltammetry (DPV) and achieved detection limit of 4.1×10⁻⁸ mol L⁻¹ and 1.7×10⁻⁸ mol L⁻¹, respectively, presenting as alternative composites to be used in the analysis of antibiotics.     

Division Electrosynthesis of Palladium Nanomaterials with Copper–Graphene as Sacrificial Templates and Its Application for Hydrazine Sensing

One‐pot electrodeposited copper‐graphene (Cu‐GE ) nanocomposite acting as sacrificial template for the division electrosynthesis of palladium nanoparticles (PdNPs ) on pyrolytic graphite electrode (PGE ) was synthesized. The designed PdNPs‐GE nanocomposite was evaluated as a new material for highly sensitive determination of hydrazine (N₂H₄ ). Scanning electron microscopy revealed that the PdNP‐GE ‐modified PGE had uniform morphology. The results of energy‐dispersive X‐ray spectrograms confirmed the ingredients of the division electrosynthesis process. Electrochemical experiments were performed to characterize the sensing properties of PdNPs‐GE toward the electrocatalytic oxidation of N₂H₄ at 0.20 V in sodium phosphate buffered saline (0.1 M pH 7.0). The sensor showed fast response (<3 s), high sensitivity [398 (1 × 10⁻⁶ A) (1 × 10⁻³ M)⁻¹], and broad linearity in the range 2.5 × 10⁻⁸–2.7 × 10⁻⁴ M with a relatively low detection limit of 1.0 × 10⁻⁸ M (S/N = 3).     

Electrochemical Determination of the KRAS Genetic Marker for Colon Cancer with Modified Graphete and Graphene Paste Electrodes

The determination of KRAS was performed using electrochemical sensing devices based on graphite and graphene pastes, modified with a phthalocyanine-boron dipyrromethene (BODIPY) and azulenes dyes. The limits of quantification for KRAS were 1.54?×?10^?4?µg/mL using the sensor based on the phthalocyanine-BODIPY dye and graphite, 2.64?×?10^?7?µg/mL using the sensor based on 2,6-bis((E)-2-(furan-2-yl)vinyl)-4-(4,6,8-trimethylazulen-1-yl)pyridine/TiO₂Pt/reduced graphene oxide, and 3.84?×?10^?3?µg/mL using the sensor based on 2,6-bis((E)-2-(thiophen-3-yl)vinyl)-4-(4,6,8-trimethylazulen-1-yl)pyridine/TiO₂Pt/reduced graphene oxide. Recovery measurements demonstrated the suitable analytical performance of these sensors for the early detection of colon cancer by the analysis of whole blood samples.     

The NADH Electrochemical Detection Performed at Carbon Nanofibers Modified Glassy Carbon Electrode

In this work, the capability of carbon nanofibers to be used for the design of catalytic electrochemical biosensors is demonstrated. The direct electrochemistry of NADH was studied at a glassy carbon electrode modified using carbon nanofibers. A decrease of the oxidation potential of NADH by more than 300 mV is observed in the case of the assembled carbon nanofiber‐glassy carbon electrode comparing with a bare glassy carbon electrode. The carbon nanofiber‐modified electrode exhibited a wide linear response range of 3×10^?5 to 2.1×10^?3 mol L^?1 with a correlation coefficient of 0.997 for the detection of NADH, a high specific sensitivity of 3637.65 (μA/M cm²), a low detection of limit (LOD=3σ) of 11 μM, and a fast response time (3 s). These results have confirmed the fact that the carbon nanofibers represent a promising material to assemble electrochemical sensors and biosensors.     

Comparative Study on Electroanalysis of Fenthion Using Silver Amalgam Film Electrode and Glassy Carbon Electrode Modified with Reduced Graphene Oxide

Oxidation and reduction processes of the insecticide fenthion was comparatively investigated at a reduced graphene oxide modified glassy carbon electrode (RGO‐GCE) and a cyclic renewable silver amalgam film electrode (Hg(Ag)FE) using square wave stripping voltammetry (SWSV). The influence of pH and SW parameters was investigated. The linear concentration ranges were found to be 1 × 10⁻⁶ – 2 × 10⁻⁵ and 1 × 10⁻⁷ – 2 × 10⁻⁵ mol L⁻¹ for Hg(Ag)FE and RGO‐GCE, respectively. The detection and quantification limits were calculated as 1.3 × 10⁻⁷ and 4.5 × 10⁻⁷ mol L⁻¹ for Hg(Ag)FE and 7.6 × 10⁻⁹ and 2.5 × 10⁻⁸ mol L⁻¹ for RGO‐GCE. Both of the developed electroanalytical methods offer rapid and simple detection of fenthion and were used on spiked tap and river water and apple juice samples. Scanning electron microscopy was used for RGO‐GCE surface characterization.     

Determination of Explosives Using Electrochemically Reduced Graphene

A graphene‐based electrochemical sensing platform for sensitive determination of explosive nitroaromatic compounds (NACs) was constructed by means of electrochemical reduction of graphene oxide (GO) on a glassy carbon electrode (GCE). The electrochemically reduced graphene (ER‐GO) adhered strongly onto the GCE surface with a wrinkled morphology that showed a large active surface area. 2,4‐Dinitrotoluene (2,4‐DNT), as a model analyte, was detected by using stripping voltammetry, which gave a low detection limit of 42 nmol L⁻¹ (signal‐to‐noise ratio=3) and a wide linear range from 5.49×10⁻⁷ to 1.1×10⁻⁵ M . Further characterizations by electrochemistry, IR, and Raman spectra confirmed that the greatly improved electrochemical reduction signal of DNT on the ER‐GO‐modified GC electrode could be ascribed to the excellent electrocatalytic activity and high surface‐area‐to‐volume ratio of graphene, and the strong π–π stacking interactions between 2,4‐DNT and the graphene surface. Other explosive nitroaromatic compounds including 1,3‐dinitrobenzene (1,3‐DNB), 2,4,6‐trinitrotoluene (TNT), and 1,3,5‐trinitrobenzene (TNB) could also be detected on the ER‐GO‐modified GC electrode at the nM level. Experimental results showed that electrochemical reduction of GO on the GC electrode was a fast, simple, and controllable method for the construction of a graphene‐modified electrode for sensing NACs and other sensing applications.     

Graphene/Poly(vinylferrocene) Composite Based Amperometric Biosensor for L‐lysine Determination

A novel and sensitive amperometric biosensor for L‐lysine determination based on a glassy carbon electrode (GCE) modified with graphene (GR) and redox polymer poly(vinylferrocene) (PVF) was constructed. L‐lysine‐α‐oxidase was immobilized onto the modified GCE by a glutaraldehyde/bovine serum albumin cross‐linking procedure. SEM, CV and EIS were used for the characterization of the surface morphology and stepwise fabrication processes of PVF/GR composite. Optimal composition of the biosensor and experimental conditions that affect the performance of the biosensor are discussed. The effect of buffer pH on biosensor response was studied in detail over a wide pH range. L‐lysine biosensor displayed a linear range of 9.9×10⁻⁷ ‐ 3.1×10⁻⁴ M with a low detection limit of 2.3×10⁻⁷ M and K_M ^app value of 0.4 mM. The L‐lysine biosensor was tested using pharmaceutical sample and cheese with satisfactory results.     

Electrochemical Sensing Platform Based on Graphene Oxide-chitosan for Simultaneous Determination of some Antihypertensive Drugs

The development of selective and simple methods for the determination of different analytes is of great interest. This is the first time to show the applicability of graphene oxide-chitosan (GO-CS) nanocomposite for designing an electrochemical nanosensor for determination of Amlodipine, Valsartan, and Hydrochlorothiazide, simultaneously. Differential pulse voltammetrics current of AML, HCT, and VAL increased linearly in the ranges of 0.1–110, 0.1–110, and 1–230 μM with LOD of 5.5×10⁻², 3.5×10⁻² and 8.6×10⁻² μM, respectively. Finally, GO-CS/GCE was used for the detection of these drugs in commercial tablets and compared with the reference method (HPLC).     

Binary Metal Oxide Adsorbed Graphene Modified Glassy Carbon Electrode for Detection of Riboflavin

Tungsten oxide (W) decorated titanium oxide (T) adsorbed onto a graphene (Gr) and modified the glassy carbon electrode for the electrochemical quantification of riboflavin (RF) in edible food and pharmaceuticals. For comparison, nanocomposites are formed using graphene oxide (GO), reduced graphene oxide (rGO) and pure graphite (G) sheets to study the electrochemical activities towards riboflavin. The ternary WTGr modified GCE shows the highest electrocatalytic activity due to synergetic interactions between the metal oxide and graphene. The electrochemical observations are supported by the SEM, HRTEM, XRD, UV-Vis, Zeta potential (ζ) and size data. The sensor shows a wide linear range 20 nM–2.5 μM with a detection limit 25.24 nM and sensitivity (4.249×10⁻⁸ A/nM). The fabricated sensor is validated in real samples.     

Electrochemical Detection of Epinephrine Using an L-Glutamic Acid Functionalized Graphene Modified Electrode

The development and application of an L-glutamic acid functionalized graphene nanocomposite, modified glassy carbon electrode are reported for the determination of epinephrine. The properties of the nanocomposite were characterized by scanning electron microscopy, ultraviolet-visible absorption spectroscopy, infrared spectroscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The modified electrode had high sensitivity and strongly catalytic activity for the detection of epinephrine. A linear relationship between the epinephrine concentration and the current response was obtained in the range of 1 × 10^?7 M to 1 × 10^?3 M by differential pulse voltammetry with a limit of detection of 3 × 10^?8 M. The modified electrode was employed to determine epinephrine in urine with satisfactory results.     

Amperometric Biosensors for Tyramine Determination Based on Graphene Oxide and Polyvinylferrocene Modified Screen‐printed Electrodes

A comparison of the analytical characteristics of two tyramine biosensors, based on graphene oxide (GRO) and polyvinylferrocene (PVF) modified screen‐printed carbon electrodes (SPCE), is reported. Diamine oxidase (DAOx) or monoamine oxidase (MAOx) was immobilized onto the PVF/GRO modified SPCE to fabricate the biosensors. Surface characteristics and electrochemical behaviour of the modified SPCEs were investigated by atomic force microscopy (AFM), scanning electron microscopy (SEM), energy dispersive X‐ray spectroscopy (EDX) and cyclic voltammetry (CV). Electrode surface composition and experimental variables such as pH and working potential were optimized in order to ensure a high performance. Under optimum experimental conditions, both DAOx/PVF/GRO/SPCE and MAOx/PVF/GRO/SPCE biosensors exhibited wide linear dynamic ranges for tyramine from 9.9×10^?7 to 1.2×10^?4 M and from 9.9×10^?7 to 1.1×10^?4 M, respectively. MAOx/PVF/GRO/SPCE biosensor showed higher sensitivity (11.98 μA mM^?1) for tyramine determination than the DAOx/PVF/GRO/SPCE biosensor (7.99 μA mM^?1). The substrate specifity of the biosensors to other biogenic amines namely histamine, putrescine, spermine, spermidine, tryptamine, β‐phenylethylamine and cadaverine was also investigated. The developed biosensors were successfully used for tyramine determination in cheese sample.     

Graphene Oxide/ZnO Nano Composite for Sensitive and Selective Electrochemical Sensing of Levodopa and Tyrosine Using Modified Graphite Screen Printed Electrode

Determination of levodopa and tyrosine as two important species for treatment of Parkinson's disease is described. A novel electrochemical sensor involving graphene oxide/ZnO nanorods (GR/ZnO) nano composite and the graphite screen‐printed electrodes (GSPE) was developed for the simultaneous detection of levodopa and tyrosine. The screen‐printed electrodes with several advantages, including low cost, versatility and miniaturization were employed. On the other hand, the graphene oxide/ZnO nanorods nano composite was casted on the surface of GSPE to obtain GR/ZnO/SPE. The proposed nano sensor has excellent performance such as high sensitivity, good selectivity and analytical application in real samples. The combination of graphene oxide/ZnO nanorods nano composite with the screen‐printed electrode is favorable for amplifying electrochemical signals. Under optimized conditions square wave voltammetry (SWV) exhibited linear dynamic ranges from 1.0×10^?6 to 1.0×10^?3 M and 1.0×10^?6 to 8.0×10^?4 M with detection limits of 4.5×10^?7 M and 3.4×10^?7 M for levodopa and tyrosine respectively.     

Selective Detection of Dopamine in the Presence of Uric Acid Using NiO Nanoparticles Decorated on Graphene Nanosheets Modified Screen‐printed Electrodes

A convenient, low cost, and sensitive electrochemical method, based on a disposable graphene nanosheets (GR) and NiO nanoparticles modified carbon screen printed electrode (NiO/GR/SPE), is described for the simultaneous determination of dopamine (DA) and uric acid (UA). The modified electrode exhibited good electrocatalytic properties toward the oxidation of DA and UA. A peak potential difference of 150 mV between DA and UA was large enough to determine DA and UA individually and simultaneously. The anodic peak currents of DA were found to be linear in the concentration range of 1.0–500.0 μM with the detection limit of 3.14×10^?7 M.     

Application of graphene oxide nanosheets as probe oligonucleotide immobilization platform for DNA sensing

In this work, a simple and novel electrochemical biosensor based on a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) was developed for detection of DNA sequences. The morphology of prepared nanoplatform was investigated by scanning electron microscopy, infrared (FTIR) and UV/Vis absorption spectra. The fabrication processes of electrochemical biosensor were characterized with cyclic voltammetry and electrochemical impedance spectroscopy (EIS) in an aqueous solution. The optimization of experimental conditions such as immobilization of the probe BRCA1 and its hybridization with the complementary DNA was performed. Due to unique properties of graphene oxide nanosheets such as large surface area and high conductivity, a wide liner range of 1.0 × 10^?17–1.0 × 10^?9 M and detection limit of 3.3 × 10^?18 M were obtained for detection of BRCA1 5382 mutation by EIS technique. Under the optimum conditions, the proposed biosensor (ssDNA/GO/GCE) revealed suitable selectivity for discriminating the complementary sequences from non-complementary sequences, so it can be applicable for detection of breast cancer.     

Electroanalysis of Dopamine at RuO2 Modified Vertically Aligned Carbon Nanotube Electrode

Electrochemical behavior of dopamine at the RuO₂‐modified vertically aligned carbon nanotubes electrode was investigated by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The RuO₂‐modified carbon nanotube electrode showed higher electrocatalytic activity towards the oxidation of dopamine than the MWNTs electrode in 0.10 M phosphate buffer solution. At an applied potential of +0.4 V, the RuO₂/MWNTs electrode exhibited a wide detection range up to 3.6×10^?3 M with detection limit of 6.0×10^?8 M (signal/noise=3) for dopamine determination. Meanwhile, the optimized sensor for dopamine displayed a sensitivity of 83.8 μA mM^?1 and response time of 5 s with addition of 0.20 mM dopamine. In addition, DPV experiment revealed that interfering species such as ascorbic acid and uric acid could be effectively avoided. The RuO₂/MWNTs electrode presents stable, highly sensitive, favorable selectivity and fast amperometric response of dopamine.     

Pt‐Pd Bimetallic Nanoparticles Decorated Nanoporous Graphene as a Catalytic Amplification Platform for Electrochemical Detection of Xanthine

The nanoporous graphene papers (NGPs) was prepared by the hard‐template method. The Pt−Pd modified NGPs hybrid was prepared by the self‐assembly method. Then a glassy carbon electrode (GCE) modified with Pt−Pd bimetallic nanoparticles‐functionalized nanoporous graphene composite has been prepared for the electrochemical determination of Xanthine (XA). The Pt−Pd/NGPs hybrid was characterized by transmission electron microscopy, scanning electron microscope and X‐ray diffraction. The electrochemical behavior of XA on Pt−Pd/NGPs/GCE was investigated by cyclic voltammetry and amperometric i‐t. The Pt−Pd/NGPs modified electrode exhibited remarkably electrocatalytic activity towards the oxidation reaction of XA in phosphate buffer solution (pH=5.5). Under the optimal conditions, the determination of XA was accomplished by using amperometric i‐t, the linear response range from 1.0×10⁻⁵∼1.2×10⁻⁴ M. The detection limit was 3.0×10⁻⁶ M (S/N=3). The proposed modified electrode showed good sensitivity, selectivity, and stability with applied to determine XA in human urine.     

Detection of Trace Phenol Based on Mesoporous Silica Derived Tyrosinase‐Peroxidase Biosensor

A novel electrochemical biosensor for phenol based on immobilization of tyrosinase‐peroxidase on mesoporous silica is described. The enhanced sensitivity of the tyrosinase‐horseradish peroxidase based biosensor to phenol was observed on comparing with tyrosinase or horseradish peroxidase monoenzyme modified electrodes. Two enzymes retained their enzymatic activities for phenol determination without any mediator. The preparation conditions of the biosensor are discussed. Optimization of the experimental parameters was performed with regard to pH and operating potential. The phenol sensor exhibited a fast response of less than 10 seconds. The sensitivity of the biosensor for phenol was 14 μA μM^?1 cm^?2 with a linear range from 2×10^?7 to 2.3×10^?4 M and a detection limit of 4.1×10^?9 M. The biosensor showed a good stability and reproducibility.