石墨烯修饰玻碳电极测定邻苯二酚

制备了用于测定邻苯二酚(CAT)的石墨烯修饰电极,并应用循环伏安法研究了CAT在该修饰电极上的电化学行为;用差分脉冲伏安法研究了测试底液的pH值对该修饰电极性能的影响,结果表明,此修饰电极在含不同浓度CAT的PBS溶液(pH=7.0)中测定,响应电流与CAT浓度在5.0×10-8～5.6×10-4mol/L范围内有良好的线性关系,相关系数r=0.9919,检出限为6.68×10-9mol/L(S/N=3)。与其它几种修饰电极相比,石墨烯修饰电极制备简单、响应时间快、操作简便,稳定性和重现性良好,有应用价值。     

Voltammetric Determination of an Anti-rheumatoid Drug Acemetacin on Graphite Flake Paste Electrode and Glassy Carbon Electrode

In this study, a simple and sensitive square wave voltammetric procedure has been developed for the determination of acemetacin (ACM) at graphite flake paste electrode (GFPE) and glassy carbon electrode (GCE). Under optimized conditions, the dependence of ACM peak current on its concentration showed wide linear range: 0.03–1.0 μmol L⁻¹ and 0.7–15.0 μmol L⁻¹ at GFPE and GCE, respectively. The developed method was successfully applied for the determination of ACM in pharmaceuticals and spiked urine with satisfying recoveries. The electrochemical oxidation of ACM is an irreversible process controlled by mixed nature of the mass transfer process.     

碳糊电极和化学修饰碳糊电极的制备及性能综述

碳糊电极在电化学研究中起着非常重要的作用．从电极材料选用和修饰剂选择方面综述了碳糊电极和化学修饰碳糊电极制备的几种方法,分析了碳糊电极和化学修饰碳糊电极制备技术存在的主要问题及其原因,评价了碳糊电极和化学修饰碳糊电极的表征技术、性能以及影响电极性能的因素．概括了近年来本课题组在碳糊电极研究中的一些结果．     

银掺杂聚L-甲硫氨酸修饰电极同时测定对苯二酚和邻苯二酚

用循环伏安法制备了银掺杂聚L-甲硫氨酸修饰玻碳电极,研究了对苯二酚和邻苯二酚在该修饰电极上的电化学行为,建立了同时测定对苯二酚和邻苯二酚的新方法.研究发现,在pH=5.0的磷酸盐缓冲溶液中,扫速为100 mV/s时,对苯二酚和邻苯二酚在银掺杂聚L-甲硫氨酸修饰玻碳电极上均出现1对氧化还原峰,峰电位分别为:Epa=0.228 V、Epc =0.162 V和Epa=0.347 V、Epc =0.287 V,二者的氧化峰电位差达119 mV,还原峰差达125 mV.在最佳的条件下,用差分脉冲伏安法同时测定邻苯二酚和对苯二酚的线性范围为3.00 ×10-6～1.00 ×10-4mol/L,检出限为8.0×10-7 mol/L(对苯二酚)和5.0×10-7 mol/L(邻苯二酚).此法用于废水样中对苯二酚和邻苯二酚的测定,获得满意结果.     

聚L-白氨酸-碳纳米管修饰电极同时检测对苯二酚和邻苯二酚

用Nafion将单壁碳纳米管(SWCNT)固定到玻碳电极(GCE)上,再利用电化学聚合方法将L-白氨酸(L-LEU)聚合到SWCNT/GCE上,制备得到poly L-LEU/SWCNT/GCE修饰电极。采用循环伏安法(CV)、差分脉冲伏安法(DPV)和电化学交流阻抗法(EIS)研究了对苯二酚(HQ)、邻苯二酚(CC)共存时,二者在修饰电极上的电化学行为。结果表明:此修饰电极对HQ和CC有很好的电催化和分离作用。二者在修饰电极上的氧化还原峰电流与GCE相比显著增强,HQ和CC的氧化峰电位差和还原峰电位差分别为124 mV和131 mV。HQ和CC的检测线性范围分别为2.0×10-7~1.0×10-4、5.0×10-7~1.0×10-4mol/L。检出限分别为8.0×10-8、1.0×10-7mol/L。制备的修饰电极重现性、稳定性良好。在模拟废水中采用该修饰电极对HQ和CC进行检测,结果满意。     

碳纳米纤维修饰碳糊电极用于双酚A的电化学检测

制备了碳纳米纤维修饰碳糊电极,并用于双酚A的高灵敏和高选择性电化学检测。碳纳米纤维材料经静电纺丝和碳化过程相结合制备而成,采用滴涂的方法修饰于碳糊电极表面制成电化学传感器。利用循环伏安法、交流阻抗法以及微分脉冲伏安法考察了传感器的性质及双酚A的电化学行为。结果表明,双酚A的峰电流响应与其浓度在0.8~50μmol/L之间呈良好的线性关系,检测限为0.1μmol/L。构建的电化学传感器用于环境水样中双酚A的检测具有较高的回收率。     

谷胱甘肽在高岭土修饰碳糊电极上的电化学研究

制备了高岭土修饰碳糊电极(KCPE),并以氢醌(HQ)为电催化介质测定还原型谷胱甘肽(GSH)。实验结果表明,在该电极上谷胱甘肽(GSH)的加入对氢醌的电化学响应有明显提高,且电催化氧化峰电流与GSH浓度呈良好的线性关系,由此可采用差分脉冲伏安法(DPV)对GSH进行定量测定。对修饰电极的电化学性能进行了表征,测得电极有效表面积为0.118 6 cm2、电荷传递系数为0.68、表观速率常数为1.08×104cm3·mol-1·s-1。在优化条件下,测得GSH在KCPE上的线性范围为0.1~1,2.5~25μmol/L,检出限为0.073μmol/L。用该方法对含GSH的市售药进行测定,结果满意。     

A Novel Modified Carbon Paste Electrode for Potentiometric Determination of Mercury(II) Ion

A new modified carbon paste electrode (CPE) based on a recently synthesized ligand of Ethyl‐2‐(benzoylamino)‐3‐(2‐hydroxy‐4‐methoxyphenyl)‐2‐propenoate (EBHMP) as a suitable carrier for Hg²⁺ ion was described. The electrode exhibit a super Nernstian slope of 48.5±1.0 mV per decade for Hg²⁺ ion over a wide concentration range from 3.0×10^?7–3.1×10^?2 M. The lower detection limits are 1.0×10^?7 M Hg²⁺. The electrode has a fast response time (ca. 5 s), a satisfactory reproducibility and relatively long life time. The proposed sensor shows a fairly good selectivity toward Hg²⁺ ion in comparison to other common cations. The potentiometric responses are independent of the pH of the test solution in the pH range 1.0–4.0. The proposed electrode was used as an indicator electrode in potentiometric titration of mercuric ion with standard solution of EDTA. The direct determination of mercury in spiked wastewater and an amalgam sample gave results that compare favorably with those obtained by the cold vapor atomic absorption spectrometric method.     

土豆汁修饰碳糊电极测定色氨酸的研究

本提出了用于测定色氨酸的土豆汁修饰碳糊电极，该电极选择性好，能有效地消除酪氨酸的干扰，在ｐＨ＝７．４的ＮａＨ２ＰＯ４－ＮａＯＨ生理缓冲液中，电极响应与色氨酸在９．８×１０＾－６～９．８×１０＾－５ｍｏｌ／Ｌ的浓度范围内呈线性关系，最低检出限是１．５×１０＾－６ｍｏｌ／Ｌ．并详细讨论了电极抗干扰能力与测定条件的关系。用该电极测定了实际样品氨基酸注射液中色氨酸的含量，结果与标准值吻合。     

纳米金修饰玻碳电极测定邻苯二酚

采用恒电位沉积方法将HAuCl4直接还原成纳米金并修饰于玻碳电极表面,制备了对邻苯二酚具有电催化氧化作用的纳米金修饰电极。邻苯二酚在该修饰电极上发生一可逆的氧化还原反应。在磷酸盐缓冲溶液(pH 7.5)中,当邻苯二酚的浓度为3.0×10-3mol.L-1时,与裸玻碳电极相比,其Epa负位移了170 mV,Epc正位移了50 mV,ΔE下降为60 mV,且峰电流显著增大,氧化峰电流与邻苯二酚浓度在5.0×10-6~4.2×10-3mol.L-1范围内呈线性关系,相关系数为0.997 6,检出限(3σ)为5.0×10-7mol.L-1。在浓度为5.0×10-4mol.L-1测得RSD(n=10)为2.9%,回收率在98.0%~101.0%之间。     

蒙脱石修饰碳糊电极测定苯酚的研究

本文报道蒙脱石修饰碳糊电极在醋酸盐缓冲溶液(pH=3.6)中,用微分脉冲伏安法测定苯酚。在+0.90 V(vs.Ag/AgCl)有一灵敏的氧化峰,伏安响应要比碳糊电极高得多.对测定苯酚的条件进行了研究,苯酚在0.1～1.0μg/ml范围内呈线性,检出限为40ng/ml,相对标准偏差为6.7％,平均回收率为97.2％。用此方法,不经分离直接测定饮料中的酚。还对苯酚在蒙脱石修饰碳糊电极上的反应机理进行了探讨。     

Voltammetric Determination of Bismuth in Water and Nickel Metal Samples with a Sodium Montmorillonite (SWy-2) Modified Carbon Paste Electrode

A simple and reliable electrochemical method for the determination of bismuth in water and nickel metal samples using a sodium montmorillonite (SWy-2) modified carbon paste electrode was described. Due to its strong cation-exchange ability and adsorptive characteristics, SWy-2 significantly enhances the sensitivity of determination for Bi³⁺. Bi³⁺ is firstly preconcentrated and then reduced on the modified electrode surface at –0.50V. After that, reduced bismuth is stripped from the electrode surface during the positive potential sweep of –0.50V to 0.20V, and a well-defined stripping peak at –0.12V appears. The stripping peak current is proportional to the concentration of Bi³⁺ from 4×10^–9molL^–1 to 1×10^–6molL^–1. The detection limit (signal-to-noise=3) is 1×10^–10molL^–1 after 5min. accumulation. The proposed method was successfully applied to the determination of bismuth in water and nickel metal samples.     

邻苯二酚和对苯二酚在钴氢氧化物膜修饰玻碳电极上的选择性测定

通过镀膜/循环伏安法制备了钴氢氧化物膜修饰的玻碳电极。该修饰电极对邻苯二酚(CA)和对苯二酚(HQ)具有较强的电催化活性。考察了支持电解质酸度对邻苯二酚和对苯二酚电化学响应的影响,选用0.1 mol/LPBS(pH 10.0)作为支持电解质。利用差示脉冲伏安法(DPV)对邻苯二酚和对苯二酚进行选择性检测,当两者浓度同时改变时,邻苯二酚和对苯二酚在6～100μmol/L范围内氧化峰电流与其浓度呈良好的线性关系,检出限分别为2×10–7,5×10–7mol/L(S/N=3)。钴氢氧化物膜电极具有较好的稳定性、重现性及较强的抗干扰能力,将此修饰电极应用于模拟水样中邻苯二酚和对苯二酚的测定,回收率为95.4%～100.4%。     

Determination of Trichloroacetic Acid (TCAA) Using CdO Nanoparticles Modified Carbon Paste Electrode

In this paper, the electrochemical behavior of a carbon paste electrode modified with CdO nanoparticles as a potential electrocatalyst for the reduction of trichloroacetic acid (TCAA) was investigated using cyclic voltammetry and double‐potential step chronoamperometry. The modified electrode showed a great enhancement in cathodic peak current with respect to reduction of TCAA in acidic aqueous solution. Using this increment, a quantitative method was developed for the determination of TCAA in aqueous solution. The detection limit and linear dynamic range of TCAA are 2.3×10^?6 M and 2.3×10^?4–3×10^?6 M, respectively.     

Amperometric L‐cysteine Sensor Using a Gold Electrode Modified with Thiolated Catechol

A thiolated catechol (CA) consisting of 1,6‐Hexanedithiol (HDT) and CA was modified on a gold (Au) electrode to obtain an amperometric L‐cysteine sensor with detection limit of 60.6 nM. The preparation of thiolated CA was conducted via a thiol addition between HDT and electro‐oxidized CA (EOCA). Briefly, the thiol addition reaction was accomplished by potential cycling of HDT/Au electrode in 0.1 M phosphate buffer (PB, pH 7.2) containing CA, and an EOCA‐HDT/Au electrode was produced. The obtained EOCA‐HDT/Au electrode exhibits a pair of well‐defined redox peaks (at 0.22/0.10 V) of o‐quinone moiety, which effectively mediates the oxidation of L‐cysteine in a 0.1 M PB (pH 7.2), with an over‐potential decrease by ca. 0.12 V (versus bare Au electrode). Electrochemical quartz crystal microbalance, cyclic voltammetry and surface‐enhanced Raman spectra were used to study relevant processes and/or film properties. The amperometric L‐cysteine sensor has good anti‐interferent ability and reproducibility. It also has acceptable recovery for detection of L‐cysteine in urine samples.     

Chemically Modified Carbon Paste Electrode for Determination of Sulfate Ion by Potentiometric Method

Four Schiff base complexes of different metal ions, M=Cr(III), Mn(III), Fe(III), and Co(III), were studied to characterize their ability as sulfate ion carriers in carbon paste electrode (CPE). The modified CPE electrode with Schiff base complex of Cr(III), N,N′‐ethylenebis(5‐hydroxysalicylideneiminato) chromium(III) Chloride, showed good response characteristics to SO₄^2? ion. The proposed electrode exhibits a Nernstian slope of 28.9±0.4 mV per decade for SO₄^2? ion over a wide concentration range from 1.5×10^?6?4.8×10^?2 M, with a detection limit of 9.0×10^?7 M. The CPE electrode manifested advantages of relatively fast response time, suitable reproducibility and life time and, most important, good potentiometric selectivity relative to a wide variety of other common inorganic anions. The potentiometric response of the electrode is independent of the pH of the test solution in the pH range 4.0–9.0. The proposed electrode was used as an indicator electrode in potentiometric titration of sulfate with Ba²⁺ ion, the determination of zinc in zinc sulfate tablet and also determination of sulfate content of a mineral water sample.     

Conducting Polymer/Ionic Liquid Composite Modified Carbon Paste Electrode for the Determination of Carbaryl in Real Samples

A new method has been described for carbaryl determination using a simple electrochemical sensor. The unique properties of poly‐pPhenylenediamine and ionic liquid were exploited to fabricate carbon paste electrode modified with composite based on conducting polymer/ionic liquid. Electrode surface characterization was performed by electrochemical methods (cyclic voltammetry and electrochemical impedance spectroscopy) and by scanning electron microscopy. Differential pulse voltammetry was employed for the detection of carbaryl in acetate buffer solution. Different parameters affecting the carbaryl response were optimized such as ionic liquid amounts, cycle number of polymerization and monomer concentration, pH, and accumulation time. Under the optimum experimental conditions, a linear response was obtained between 0.5 and 200 μmol/L, with detection limit of 0.09 μmol/L. The developed sensor offered satisfactory results for carbaryl detection in spring water and fruit samples.     

Enhanced Electrochemical Determination of Catechol and Hydroquinone Based on Pd Nanoparticles/Poly(Taurine) Modified Glassy Carbon Electrode

Here, Pd nanoparticles and poly(taurine) film was prepared on the glassy carbon electrode surface (Pd/Poly(TAU)/GCE) by the rapid electrochemical technique. The proposed composite surface was characterized by scanning electron microscopy(SEM), X‐ray photoelectron spectroscopy(XPS) and electrochemical impedance spectroscopy(EIS). Enhanced electron transfer ability and higher electroactive surface area were achieved at Pd/Poly(TAU)/GCE as compared to the bare GCE and polymer film electrode. The new and highly stable Pd/Poly(TAU)/GCE was employed for the individual and simultaneous determination of hydroquinone and catechol which were environmentally toxic. Under the optimized conditions, HQ and CC were individually determined by using the differantial pulse voltammetry in the linear ranges of 0.008–100 μM and 0.001–100 μM with the detection limits of (LOD) 2.1 nM and 0.68 nM, respectively. In case of simultaneous determination, LODs were found as 10 nM and 0.88 nM for HQ and CC, respectively. The content of both analytes in the real sample analysis was evaluated in the river water and tap water successfully.     

Carbon Paste Electrode Modified with Biochar for Sensitive Electrochemical Determination of Paraquat

The present work reports for the first time the determination of paraquat (PQ²⁺) by Differential Pulse Adsorptive Stripping Voltammetry (DPAdSV) using a carbon paste electrode modified (CPME) with biochar obtained from castor oil cake at different temperatures (200–600 °C). The best voltammetric response was verified using biochar yielded at 400 °C (CPME‐BC400). Linear dynamic range (LDR) for PQ²⁺ concentrations between 3.0×10^?8 and 1.0×10^?6 mol L^?1 and a limit of detection (LOD) of 7.5×10^?9 mol L^?1 were verified. The method was successfully applied for PQ²⁺ quantification in spiked samples of natural water and coconut water.