Influence of organic solvents in the mobile phase on the determination of carboxylic acids and inorganic anions in grape juice by ion chromatography

Investigations have been initiated to develop a sufficiently good separation of both major and minor organic acids and inorganic anions present in grape musts using a Dionex As11 column, a sodium hydroxide gradient elution and a suppressed conductivity detection. Separation was complicated in aqueous mobile phase by co-elutions and selectivity was optimized using organic modifiers that alter ion-exchange selectivity for hydrophobic ions. In this study, the influence of three different solvents (methanol, ethanol and acetonitrile) on the efficiency of column was compared. The best separation of all ions in a synthetic solution was achieved with an eluent containing 13% (v/v) methanol and 13% (v/v) ethanol in water, the run during only 20 min. This method was next applied to grape juices with success and has shown sensitivity and reproducibility. Moreover, sample preparation was a simple 20-fold dilution with 0.45 microm filtration and direct injection without prior sample clean-up.     

Analysis of Non-Selective Calcium-Channel Blockers by Reversed-Phase TLC

The selectivity of TLC separation of non-selective calcium-channel blockers prenylamine, lidoflazine, bepridil, and fendiline has been investigated silanized silica gel RP8 and RP18 plates. Optimization of retention and selectivity for these compounds was achieved by altering the pH and the concentration of organic modifier (methanol, ethanol, tetrahydrofuran, acetonitrile) in the aqueous mobile phases. The substances were separated in horizontal chambers and the drugs were detected by videoscanning and illumination of the plates at λ = 254 nm. On RP8 plates the best separation was achieved with 50% acetonitrile in pH 2.06 phosphate buffer as mobile phase. On RP18 the best separation was achieved with 50% ethanol in pH 2.06 phosphate buffer.

     

Use of 1-alkyl-3-methylimidazolium-based ionic liquids as background electrolytes in capillary electrophoresis for the analysis of inorganic anions

Separation of inorganic anions in CE is often a challenging task because the electrophoretic mobilities of inorganic anions are comparable to or even greater than the EOF mobility. In this study, we present the use of ionic liquids (ILs) as background electrolytes (BGEs) in CE of inorganic anions. The 1-alkyl-3-methylimidazolium-based ILs as BGEs dynamically coated the capillary wall and induced a reversed EOF. This allowed the anions to comigrate with the EOF and yielded a rapid separation. Increasing the alkyl chain length of the ILs and BGE concentration can significantly improve the separation resolution. With 40 mM 1-butyl-3-methylimidazolium tetrafluoroborate as BGE, good separations of five model anions (Br-, I-, NO2(-), NO3(-), and SCN-) were achieved in a range of buffer pH values. The separation efficiency was as high as 34 600-155 000, and the RSDs of the migration times were less than 0.8% (n = 5).     

Simultaneous Determination of Inorganic Anions and Organic Acids in Environmental Samples by Capillary Zone Electrophoresis with Indirect UV Detection

Capillary zone electrophoresis (CZE) with indirect UV detection was developed for the simultaneous determination of inorganic anions and organic acids in environmental samples. Various aromatic acids (benzoic, phthalic, trimellitic, and pyromellitic acids) were evaluated as background electrolytes (BGEs) to give high resolution and detection sensitivity. Co-electroosmotic conditions such as the concentration of BGE, electrolyte pH, and EOF modifier were systematically investigated. Three inorganic anions and ten organic acids were determined simultaneously in 10 min using an electrolyte containing 10 mM phthalic acid, 0.5 mM myristyltrimethylammonium bromide (MTAB), and 5% methanol (MeOH) (v/v) at pH 5.60. Linear plots for the test solutes were obtained in the concentration range 0.01–1.0 mM with detection limits in the range 5–30 μM. The proposed method was successfully demonstrated for the determination of inorganic anions and organic acids in natural water, soil, and plant extracts after direct sample injection.     

Exploration of the electrophoretic behaviour of borane cluster anions and of the capability of capillary electrophoresis to separate them chirally

Mobilities of investigated boron cluster compounds in 3-(N-morpholino)propanesulfonic and phosphate buffers adjusted to pH 7 either with sodium hydroxide or with tris(hydroxymethyl)aminomethane depend on both buffer ions. The zone width and zone asymmetry, which are usually markedly higher than those of organic or common inorganic ions of comparable size, depend on the type of the borane cluster anion. Unusual shapes of zones of two investigated compounds have been found in tris phosphate buffer. Acetonitrile was superior to methanol as an organic additive to separation systems from the viewpoint of the zone symmetry and separation speed. Narrow trigonal zones, typical of organic ions non-interacting with the capillary wall, have been observed for some bridged sandwich cobalt complexes in run buffers with the addition of acetonitrile. The interaction of borane cluster anions with beta-cyclodextrin cavity is excessively strong in purely aqueous solutions. Methanol and acetonitrile, which generally weaken the interaction, sometimes affect the separation enantioselectivity of various compounds in different ways in addition to the weakening effect. Chiral discrimination was reached for all ten investigated anions, which belong to four different structural types of cluster boranes. Stability constants estimated for some analyte-beta-cyclodextrin complexes range between 100 and 1800 l/mol in acceptable separations. The relative difference of the constants was from 3 to 20%.     

Study of the selectivity of inorganic anions in hydro-organic solvents using indirect capillary electrophoresis

In capillary electrophoresis (CE) analysis of small inorganic anions, the ability to control the electroosmotic flow (EOF) and the ability to alter the electrophoretic mobility of the ions are essential to improve resolution and separation speed. In this work, a CE method for separation of small inorganic anions using indirect detection in mixed methanol/water buffers is presented. The suitability of different UV absorbing probes commonly used for indirect detection including chromate, iodide, phthalate, benzoate, trimellitate, and pyromellitate, in mixed methanol/water buffers is examined. The effect of the electrolyte buffer system, including the pH, buffer concentration and the organic solvent on the electrophoretic mobility of the probes and analytes are also investigated. The EOF was reversed using cationic surfactant, cetyltrimethylammonium bromide (CTAB) so ions were separated under co-EOF mode. The organic solvent alters the electrophoretic mobility of the probes and the analytes differently and hence choice of the appropriate probe is essential to achieve high degree of detection sensitivity. Separations of six anions in less than 2.5 min were accomplished in buffers containing up to 30% MeOH. Adjustment of the methanol content helps to improve the selectivity and resolution of inorganic anions. Limit of detection, reproducibility and application of the method for quantification of anions in water samples will also be discussed.     

Chiral separability of hydrophobic boron cluster anions with native cyclodextrins in water-methanol background electrolytes

Cluster anions of boron are built up on three-center two-electron bonds in contrast to naturally occurring compounds and their synthetic analogs. Methanol works as a solvent and as a competing agent, which advantageously adjusts reasonable strength of their interaction with native CDs in water-organic BGE. The highest methanol concentration preserving chiral discrimination of atropoisomers of individual anions is approximately 35, 55 and 75% v/v for alpha-, beta- and gamma-CD, respectively. alpha-CD separates anionic 7, 8-nido-dicarbaundecaborate clusters with small exo-skeletal substituents. beta-CD separates anions of all four tested structural types. The efficiency of separation of a compound with alpha- or beta-CD is always markedly lower than the separation efficiency at the absence of a CD in BGE. The efficiency of separation of a compound with beta-CD is always lower than the efficiency of separation of the compound with alpha-CD. gamma-CD was proved to be unsuitable as a chiral selector because in BGEs with gamma-CD, effective mobilities of analytes as well as their differences continuously decrease. The decrease was ascribed to the decomposition of the gamma-CD. The assessment of analytical prospect of alpha- and beta-CDs as chiral selectors for chiral separations of boron cluster anions requires knowledge of stability of individual CDs at the conditions of analyses and recognition of the chance to eliminate low separation efficiency.     

有机酸与无机阴离子的梯度离子色谱法分析研究

研究了用离子色谱法梯度洗脱抑制电导检测器分析有机酸与无机阴离子的色谱条件,建立了最佳梯度程序。用阴离子交换分离,选用去离子水、氢氧化钠和甲醇作淋洗液,分别对５种二元有机酸和３种无机阴离子做二元梯度淋洗,对１０种多元有机酸和３种无机阴离子做三元梯度淋洗。方法用于果汁饮料与柠檬酸发酵液的测定,结果令人满意。     

Separation of anions by ion chromatography-capillary electrophoresis

Capillary electrophoresis (CE) with a water-soluble ion-exchange polymer in the background electrolyte is very efficient for the separation of organic and inorganic anions because the ion-exchange selectivity, as well as differences in electrophoretic mobility, can be used for separating sample ions. Poly(diallyldimethylammonium chloride) (PDDAC) was employed for this purpose. A very stable electroosmotic flow was obtained between pH 2.3 and 8.5 due to the strong adsorption of PDDAC onto the capillary wall. The effect of ion exchange on the migration of sample anions and their separation was controlled by varying the concentration of PDDAC, the concentration and the type of salt used in the CE background electrolyte. Addition of organic solvent (e.g., acetonitrile) could also modify the sample migration and the separation. Baseline separations were obtained for anions with very similar mobilities, such as bromide and iodide, naphthalenesulfonates, and bi- and tricarboxylic acids. Typical separation efficiencies were between 195,000 and 429,000 theoretical plates per meter. Ten replicate separations gave an average RSD of 1.0% for migration times of the sample anions studied. Excellent separations were obtained for a variety of samples, including a separation of 17 inorganic and organic anions in less than 6 min.     

MEKC–MS/MS method using a volatile surfactant for the simultaneous determination of 12 synthetic cannabinoids

This study describes a method for the simultaneous determination of 12 synthetic cannabinoids by MEKC–MS/MS using a volatile surfactant (ammonium perfluorooctanoate) as a constituent of the micellar pseudostationary phase. Although most synthetic cannabinoids comigrated by a CZE method, sufficient separation could be achieved by the proposed method. The best separation was made possible by 50 mM ammonium perfluorooctanoate in 20% v/v acetonitrile/water (apparent pH* 9.0) as the BGE, followed by MS detection using a sheath liquid composed of 5 mM ammonium formate in 50% v/v methanol/water mixed hydro‐organic solvent. The standard calibration curve for all analytes showed good linearity (r > 0.99). Satisfactory recoveries, ranging from 89.5 to 101.7%, were obtained. The LODs were 6.5–76.5 μg/g for the target analytes. This method appears to be a useful tool for the identification of synthetic cannabinoids in illegal herbal incense blends.     

Separation of polycyclic aromatic hydrocarbons by micellar electrokinetic chromatography with aqueous short-chain alcohol solvent

Micellar electrokinetic capillary chromatography (MEKC) with aqueous organic solvent has been developed to separate polycyclic aromatic hydrocarbons (PAHs). Methanol, ethanol or propanol as an organic modifier was added to sodium dodecyl sulfate (SDS) micellar solution in order to increase the solubility of very hydrophobic solutes in mobile phase. Both methanol and ethanol can be used as co-solvents for the separation of PAHs. Use of ethanol resulted in a shorter analysis time than use of methanol. The separations of some PAHs were unsatisfactory using propanol although the analysis time was much shorter than with ethanol. The influence of ethanol content, SDS concentration and temperature on the separations was studied. Benzene and nine polycyclic aromatic hydrocarbons were successfully separated using 50 mM SDS-20 mM phosphate-5 mM borate, containing 40% (v/v) ethanol at 35 degrees C. The relative standard deviation (R.S.D.) of t(R) ranged from 0.5 to 1.5% for six repeat injections.     

Nonionic surfactant enhanced semipermanent coatings for capillary electrophoresis of inorganic anions without use of organic additives

Separation of inorganic anions by capillary electrophoresis (CE) is usually conducted in co-electroosmotic mode due to the large electrophoretic mobilities of inorganic anions. Semipermanent surfactant coatings have been shown to be effective for CE of inorganic anions due to their strong capability of electroosmotic flow (EOF) manipulation. However, semipermanent coatings often suffer from their unsatisfactory stability. In addition, organic solvent additives are usually required to adjust the selectivity, which also aggravate the degradation of coating. In this work, a novel semipermanent coating consisting of cationic Gemini surfactant 18-10-18 and nonionic surfactant Tween 20 was developed to separate inorganic anions in CE. This coating is easy to prepare and more stable than pure Gemini coating. The introduction of nonionic surfactant in the coating not only suppresses the reversed EOF but can also adjust the selectivity of separation. Good separations of six model anions were achieved, the separation efficiency was as high as 65040-169700 plates/m and the RSDs of the migration times were less than 0.5 and 2.5% for run-to-run and day-to-day assays, respectively. Calibration curves were linear in the range of 0.05-5.0 mM; the detection limits ranged from 20 to 50 μM. More importantly, no organic solvents are required in the background buffer to achieve the satisfactory separations. This guarantees the coating stability and makes the method greener than most of other methods for CE of inorganic anions.     

Online concentration by field-amplified sample injection in acidic buffer for analysis of fangchinoline and tetrandrine in herbal medicine by flow injection-micellar electrokinetic capillary chromatography

A novel, rapid, and continuous online concentration approach based on field-amplified sample injection for the analysis of fangchinoline and tetrandrine was developed in this paper by combination of flow injection-MEKC. The BGE used was a solution composed of 75 mM H3PO4-triethylamine-2.5% v/v polyoxyethylene sorbitan monolaurate-20% v/v methanol buffer (pH* 5.0). The analytes prepared in 50% v/v aqueous ethanol were used as the test analytes. Sample was injected electrokinetically between plugs of water. When the cations reached the boundary between the water plug and BGE, they slowed down and became concentrated. Thereafter, MEKC was initiated for the separation. This results in 6.8-8.9-fold improvement in concentration sensitivity relative to conventional CE methods. The separation could be achieved within 10 min and sample throughput rate can reach up to 50/h. The repeatability (defined as RSD) was 4.8, 4.4% with peak height evaluation and 3.6, 0.94% with peak area evaluation for TET and FAN, respectively.     

离子色谱法同时分析啤酒中的有机酸和无机阴离子

建立了以NaOH-甲醇混合淋洗液,离子交换色谱柱,电导检测器检测,分离啤酒中有机酸和无机阴离子的离子色谱法.结果表明：在20 min内分离出啤酒中的11种主要有机酸与无机阴离子,方法回收率和相对标准偏差分别为96.30%～104.8%和0.02%～4.0%.     

Separation of anti-tumor peptides by capillary electrophoresis in organic solvent containing background electrolytes

Connections between the calculated and measured electrophoretic mobilities (nu(ep)) determined by capillary electrophoresis as well as connections between the measured and calculated diffusion coefficients of anti-tumor peptides have been investigated in background electrolytes (BGEs) containing different organic solvents (acetonitrile, methanol, ethanol and isopropanol). Comparison of the electrophoretic mobility (nu(ep)) values revealed discrepancies between the measured and calculated values. However, no change in the migration order or selectivity could be expected from the calculated nu(ep) values, variation of both properties was observed applying organic solvents as BGE modifiers. Experimental determination of the diffusion coefficient suggested that the effect of the organic solvents is not restricted to the change of the BGE viscosity. The reason for the discrepancy between the measured and calculated mobility values might be the possible conformation and/or solvation changes of the peptide caused by the different organic solvents.     

单一阴离子交换柱同时分离有机酸和无机阴阳离子

研究了用乙二胺四乙酸（ＥＤＴＡ）作淋洗液时，性质迥异的有机酸、无机阴离子和碱土金属离子（Ｃａ＾２＋、Ｍｇ＾２＋）在同一阴离子交换柱上的同时分离以及保留机理，结果表明，在离子交换机理之外，非离子交换机理对有机酸及钙镁的ＥＤＴＡ络阴郭的保留行为起一定的辅助作用，９种有机酸和无机阴阳离子在１０ｍｉｎ内得到了较好的分离。各离子的电导检测灵敏度在１０＾－９至１０＾－１１ｍｏｌ，能满足环境和食吕分析的要求。     

Polymeric ionic liquid as a background electrolyte modifier enhancing the separation of inorganic anions by capillary electrophoresis

A novel and easy method for the separation of inorganic anions by capillary electrophoresis using a polymeric ionic liquid (PIL), poly(1-vinyl-3-butylimidazolium bromide) as a background electrolyte modifier has been developed. The PIL has been proved to generate a reversed electroosmotic flow which reduces the analysis time and improves the separation significantly. Effects of the PIL concentration and buffer composition (pH and concentration) were evaluated on basis of the resolution and efficiency of the sample. Under optimum conditions, good separation of six model inorganic anions was achieved with high efficiency and excellent reproducibility within 3 min. The results obtained indicate that the combination of reversed EOF and the association between the analytes and the PIL on the capillary wall or BGE play a prominent role in the separation of anions. Therefore, the PIL presents a useful alternative for the BGE modifier in the study of inorganic anions by CE.     

Application of co-electroosmotic capillary electrophoresis for the determination of inorganic anions and carboxylic acids in soil and plant extract with direct UV detection

Summary Indirect UV detection in capillary zone electrophoresis (CZE) is frequently used for the determination of inorganic anions and carboxylic acids. However, there are few reports on direct UV detection of these solutes in real samples. This paper describes the use of direct UV detection of inorganic anions and organic acids in environmental samples using co-electroosmotic capillary zone electrophoresis (co-CZE) at 185 nm. The best separation and detection of the solutes was achieved using a fused silica capillary with an electrolyte containing 25 mM phosphate, 0.5 mM tetradecyltrimethylammonium bromide (TTAB) and 15% acetonitrile (v/v) at pH 6.0. Four common inorganic anions (Cl⁻, NO₂ ⁻, NO₃ ⁻ and SO₄ ²⁻) and 11 organic acids (oxalic, formic, fumaric, tartaric, malonic, malic, citric, succinic, maleic, acetic, and lactic acid), were determined simultaneously in 15 min. Linear calibration plots for the test solutes were obtained in the range 0.02–0.5 mM with detection limits ranging from 1–9 μM depending on the analyte. The proposed method was successfully used to determine inorganic anions and carboxylic acids in soil and plant tissue extracts with direct injection of the sample.     

无机阴离子的毛细管电泳分析

本文研究了常见无机阴离子的毛细管电泳规律，考察了分离电压、电解质熔液组成、浓度、ｐＨ值等对分离的影响，建立了高效、快速的无机阴离子毛细管电泳分析方法。在选定的实验条件下，各种常见无机阴离子在５ｍｉｎ内达到完全分离，对Ｂｒ＾－和Ｃｌ＾－的分离柱效每米可达７６万理论板数。迁移时间的相对标准偏差小于１％，峰面积的相对标准偏差小于５％，各离子的最低检测浓度为０．０５￣０．５μｇ／ｍｌ。     

Comparison of retention of aromatic hydrocarbons with polar groups in binary reversed-phase high-performance liquid chromatography systems

The retention of aromatic hydrocarbons with polar groups has been correlated as log k1 versus log k2 for reversed-phase high-performance liquid chromatography systems with different binary aqueous mobile phases containing methanol, acetonitrile or tetrahydrofuran as modifiers. Distinct changes in separation selectivity have been observed between tetrahydrofuran and acetonitrile or methanol systems. Methanol and acetonitrile systems show lower diversity of separation selectivity. The changes in retention and selectivity of aromatic hydrocarbons with various polar groups between any two chromatographic systems with binary aqueous eluents (tetrahydrofuran vs. acetonitrile, tetrahydrofuran vs. methanol and methanol vs. acetonitrile) have been interpreted in terms of molecular interactions of the solute with especially one component of the stationary phase region, i.e. extracted modifier, and stationary phase ordering. The ordering of the stationary phase region caused by modifier type influences the chromatographic selectivity of solutes with different molecular shape.