三维连续结构Li4Ti5O12/石墨烯纳米复合材料:制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li₄Ti₅O₁₂/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物, 进一步高温热处理, 在热剥离石墨烯的孔道内原位形成Li₄Ti₅O₁₂纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中, 热剥离石墨烯的三维连续结构确保了Li₄Ti₅O₁₂纳米粒子与石墨烯在长循环过程中的有效接触。因此, 复合材料表现出优异的循环稳定性。在5C下, 5 000次循环后, 其容量保持率高达94%。     

Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

Li4Ti5O12-聚苯胺复合材料的合成与表征

以醋酸锂和钛酸四丁酯为原料，以乙醇为溶剂，采用溶胶-凝胶法制备Li₄Ti₅O₁₂;以苯胺、过硫酸铵为原料，以盐酸为溶剂，采用原位聚合法合成Li₄Ti₅O₁₂-聚苯胺复合材料。采用X-射线衍射、红外光谱和电化学测试等对复合材料进行了表征。结果表明，聚苯胺的加入明显提高了Li₄Ti₅O₁₂的电子导电性能，Li₄Ti₅O₁₂-PAn复合材料具有比Li₄Ti₅O₁₂更好的高倍率性能和循环稳定性。0.1C和2.0C放电时Li₄Ti₅O₁₂-PAn的放电容量达到了191.3和148.9 mAh·g^-1，经80次循环后二者平均每次循环容量衰减率分别为0.13%和0.61%。     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

锂离子电池用Li4Ti5O12-碳复合材料的制备与电化学性能

Li₄Ti₅O₁₂-C composite was prepared by sol-gel method using ethyl alcohol as solvent, lithium acetate and tetrabutyl titanate as raw materials, and graphite as carbon source. Li₄Ti₅O₁₂-C composites were characterized by thermogravimertric(TG) analysis and differential thermal analysis(DTA), X-ray diffraction(XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and electrochemical tests. Results show that Li₄Ti₅O₁₂-C composite with 5% carbon containing can be obtained by annealing the precursor at 600 ℃ for 6 h in N₂ atomsphere. The composites can deliver a specific capacity of 167.1 mAh·g^-1, 99.0% and 105.1% of the capacity can be retained after discharged for 80 times at 0.1C and 2.0C, respectively. Compared with pure Li₄Ti₅O₁₂, Li₄Ti₅O₁₂-C composite shares larger discharge capacity, better cyclability and rate performance.     

Bi2Ti2O7/TiO2/Bi4Ti3O12多异质结的构筑及其增强的可见光催化性能

以静电纺丝技术制备的TiO₂纳米纤维为基质,硝酸铋为铋源,KOH为矿化剂,成功制备了多异质结Bi₄Ti₃O₁₂/TiO₂/Bi₂Ti₂O₇复合纳米纤维光催化剂。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外可见漫反射光谱(UV-Vis DRS)等一系列表征,对其物相组成、微观形貌和光学性质等进行分析。结果表明： TiO₂纳米纤维的介入,将Ⅰ型异质结Bi₂Ti₂O₇/Bi₄Ti₃O₁₂分离为2个Ⅱ型异质结Bi₂Ti₂O₇/TiO₂和Bi₄Ti₃O₁₂/TiO₂。Bi₂Ti₂O₇、Bi₄Ti₃O₁₂和TiO₂三者的协同作用,有效提高了可见光吸收能力,改变了光生载流子的传输路径,降低了光生电子与空穴的复合几率,从而获得高效的光催化降解CH₃CHO性能。可见光照8 h,Bi₄Ti₃O₁₂/TiO₂/Bi₂Ti₂O₇复合纳米纤维对CH₃CHO的降解率达到87.1%。     

正极材料LiNi0.5Mn1.5O4的合成及性能

采用低温固相法制备镍锰复合草酸盐，煅烧后生成的镍锰复合氧化物与Li₃CO₃混合，在空气中于700 ℃反应12 h，得到LiNi_0.5Mn_1.5O₄。通过XRD，SEM和恒电流充放电测试对样品进行了表征。XRD结果表明：复合草酸盐经390 ℃煅烧3 h，生成了多相氧化物；合成的LiNi_0.5Mn_1.5O₄为纯相，具有立方尖晶石结构。电化学测试结果表明，合成的样品在室温和高温(55 ℃)下，具有较好的电化学性能；大电流充放电时，具有良好的循环性能。     

LixNi0.5Co0.5O2的态密度计算及电化学性能研究

>为获得综合性能更好的锂离子二次电池正极材料, 分析了Co掺杂对Li_xNiO₂电化学性能的影响. 采用密度泛函DFT理论对Li_xNiO₂和Li_xNi_0.5Co_0.5O₂的平均放电电压和态密度进行了计算. 同时, 用共沉淀法制备了Li_xNiO₂和Li_xNi_0.5Co_0.5O₂锂离子二次电池正极材料, 并对其进行了XRD结构分析和恒流充放电测试. 实验和计算结果表明: 随锂离子嵌入正极(电池放电), 电池的电压逐渐降低, 材料的态密度峰向低能量方向移动; 与Li_xNiO₂相比, Li_xNi_0.5Co_0.5O₂的电压平台相对较高(当0.25≤x≤0.5), 而且在Li^＋嵌/脱时, Li_xNi_0.5Co_0.5O₂的结构变化相对较小; Co离子的掺入, 减小了NiO₆八面体的畸变度, 使材料的电化学稳定性得以提高. 在钴掺杂镍酸锂体系中, NiO₆和CoO₆具有相互的稳定作用.     

Li4Ti5O12溶胶-凝胶法合成及其机理研究

The precursors of Li₄Ti₅O₁₂ were prepared from tetrabutyl titanate and lithium acetate by sol-gel process. The Li₄Ti₅O₁₂ samples were synthesized by calcining the gel precursors at 400～900 ℃ in air for 6～20 h. Its reaction mechanism was investigated by infrared spectroscopy(IR), thermogravimetry(TG) and X-ray diffraction(XRD). The effects of sinter-temperature, calcination-time and thermal-treatment for the products were discussed. The samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM). The results showed that the single-phase products were obtained by calcining the gel precursors at 800 ℃ in air for 20 h, the sinter-temperature was lower than that of solid-state method, the particles were narrowly distributed, well crystallized with a size range from 0.3μm to 0.5 μm.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

A new 2212-type stair like structure: Bi14Sr21Fe12O61, m=5 member of the generic [Bi2Sr3Fe2O9]m[Bi4Sr6Fe2O16] family

A new oxide, Bi₁₄Sr₂₁Fe₁₂O_61, with a layered structure derived from the 2212 modulated type structure Bi₂Sr₃Fe₂O₉, was isolated. It crystallizes in the I2 space group, with the following parameters: a=16.58(3) Å, b=5.496(1) Å, c=35.27(2) Å and β=90.62°. The single crystal X-ray structure determination, coupled with electron microscopy, shows that this ferrite is the m=5 member of the [Bi₂Sr₃Fe₂O₉]_m[Bi₄Sr₆Fe₂O₁₆] collapsed family. This new collapsed structure can be described as slices of 2212 structure of five bismuth polyhedra thick along , shifted with respect to each other and interconnected by means of [Bi₄Sr₆Fe₂O₁₆] slices. The latter are the place of numerous defects like iron or strontium for bismuth substitution; they can be correlated to intergrowth defects with other members of the family.     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃‐Bi₂O₃‐ZnO‐Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1364,介电损耗低至1.2%。     

Crystal growth, structural characterization and magnetic properties of Ca3CuRhO6, Ca3Co1.34Rh0.66O6 and Ca3FeRhO6

Single crystals of Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆ and Ca₃FeRhO₆ were synthesized by high temperature flux growth in molten K₂CO₃ and structurally characterized by single crystal X-ray diffraction. While Ca₃Co_1.34Rh_0.66O₆ and Ca₃FeRhO₆ crystallize with trigonal (rhombohedral) symmetry in the space group , Z=6: Ca₃Co_1.34Rh_0.66O₆a=9.161(1) Å, c=10.601(2) Å; Ca₃FeRhO₆a=9.1884(3) Å, c=10.7750(4) Å; Ca₃CuRhO₆ adopts a monoclinic distortion of the K₄CdCl₆ structure in the space group C2/c, Z=4: a=9.004(2) Å, b=9.218(2) Å, c=6.453(1) Å, β=91.672(5). All crystals of Ca₃CuRhO₆ examined were twinned by pseudo-merohedry. Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆, and Ca₃FeRhO₆ are structurally related and contain infinite one-dimensional chains of alternating face-sharing RhO₆ octahedra and MO₆ trigonal prisms. In the monoclinic modification, the copper atoms are displaced from the center of the trigonal prism toward one of the rectangular faces adopting a pseudo-square planar configuration. The magnetic properties of Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆, and Ca₃FeRhO₆ are discussed.