丙烯酸乙酯在炭黑表面的阴离子接枝聚合研究

丙烯酸乙酯在炭黑表面的阴离子接枝聚合研究蒋子铎，刘长生，刘安华，吴璧耀（武汉化工学院精细化工系武汉４３００７３）关键词炭黑，丙烯酸乙酯，阴离子聚合，接枝聚合由于炭黑粒子自聚力强，存在难分散、易絮凝的特点，影响其在高分子材料中的分散和分散稳定性．对此国...     

天然橡胶原位接枝炭黑的分散性研究

采用原位固相接枝方法,使在高温和强剪切作用下降解的天然橡胶接枝到炭黑表面.采用透射电镜(TEM)、原子力显微镜(AFM)等方法观察了接枝前后的炭黑粒子形貌变化,发现未接枝炭黑以微米级的附聚体形式存在,而由于炭黑聚集体被强剪切力部分破坏,接枝炭黑的聚集程度明显减弱,粒子的尺寸减小.采用激光光散射粒度仪对接枝前后炭黑的粒度进行分析,接枝炭黑的体积平均粒径为164 nm,远小于测得的原炭黑的粒径797 nm.采用沉降法、透光率法及zeta电位测量研究了接枝改性对炭黑在溶剂中的分散性及分散稳定性的影响,结果表明,接枝炭黑在接枝分子的溶剂中的分散性变好,分散稳定性提高.     

聚丙烯酸酯接枝炭黑的合成,表征及其应用

探讨聚丙烯酸酯接枝炭黑的合成条件及其影响因素。用红外光谱和元素分析对接枝物进行了表征,通过ζ－电位法,透光率和ＳＥＭ研究了接枝炭黑的分散稳定性。接枝炭黑分散于水性无皂涂料中形成黑色涂料具有良好的综合性。     

丙烯酰胺在炭黑表面接枝聚合研究

利用Ｃｅ＾４＋和羟甲基化炭黑组成的氧化还原引发体系，探讨了丙烯酰胺在炭黑表面的自由基水溶液接枝聚合机理。研究表明：单体浓度、硝酸浓度和铈盐用量直接影响丙烯酰胺在炭黑表面的接枝聚合，ＦＴＩ和ＴＥＭ分析证明：改性炭黑表面存在着聚丙烯酰胺。改性炭黑粒子的Ｚｅｔａ电位值与未改性炭黑粒子相同，但它与水组成的分散体具有极好的分散稳定性。     

丙烯酸甲酯在炭黑表面的接枝聚合及水解

在炭黑表面接枝聚合物 ,可提高其在相应介质中的分散性[1] .乙酰丙酮合锰可以有效地引发羊毛、纤维素、淀粉等天然高分子的接枝聚合 [2～ 4 ] ,季君晖 [5]将其与羟甲基化炭黑组成引发体系 ,引发了甲基丙烯酸甲酯、丙烯酸丁酯、苯乙烯等单体在炭黑表面进行接枝聚合 .但该体系难以引发水溶性的单体 ,因此得到的接枝炭黑只能用于油性体系 .目前制备亲水性接枝炭黑大多采用 Ce4 +/羟甲基化炭黑引发体系 ,该体系对 O2 特别敏感 ,反应条件相当苛刻 .本文采用乙酰丙酮合锰与羟甲基化炭黑组成引发体系 ,引发丙烯酸甲酯在炭黑表面的接枝聚合 .在 Na…     

乙烯基单体在炭黑表面上的接枝聚合

讨论了分别在铈离子体系，正丁基锂体系，过渡金属离子乙酰丙酮铜（Ⅱ）以及焦磷酸络锰（Ⅲ）体系的作用下，炭黑与乙烯基单体的接枝聚合．研究了引发剂浓度、单体浓度、反应时间对接枝聚合反应的影响．利用ＦＴ ＩＲ分析确证了炭黑表面的接枝反应，利用ＴＥＭ表征了接枝炭黑的形态．结果表明，在所研究的多种炭黑表面接枝聚合体系中，正丁基锂体系的接枝率最高，可达２００％．而各种氧化还原体素的接枝率只能达到３０％左右．表面接枝后的炭黑在介质中的分散稳定性明显改善．     

炭黑接枝方法与接枝炭黑应用的研究进展

炭黑接枝是常用的炭黑表面改性方法。讨论了最新的炭黑接枝方法,主要包括二次接枝法、γ-射线辐射接枝、三氯乙酰基团与六羰基钼引发乙烯基单体聚合接枝,偶联接枝与聚合物交联及其它方法;并对接枝炭黑在新材料领域的臆用作了介绍。     

原位接枝炭黑/天然橡胶复合材料的制备及性能

采用原位固相接枝方法,使在高温和强剪切作用下降解的天然橡胶接枝到炭黑表面.通过对接枝前后炭黑填充天然橡胶的性能对比发现,原位接枝炭黑不但能提高天然橡胶的硫化速度,还能提高拉伸强度,定伸应力和撕裂强度等;动态力学性能的测试结果表明接枝炭黑填充的天然橡胶中接枝炭黑网络化程度较低,这些结果主要归因于接枝炭黑在橡胶基体中分散性的改善及炭黑与橡胶之间作用力的增加.     

对苯乙烯磺酸钠改性炭黑对天然橡胶胶乳力学性能的影响

在Haake转矩流变仪的热机械作用下,用对苯乙烯磺酸钠(NASS)对炭黑进行预处理,制备了在水介质中具有优异的分散稳定性的亲水性纳米炭黑粒子(PNASS-CB),并将其直接用于天然橡胶胶乳的补强研究.1HNMR和FT-IR结果表明NASS在炭黑表面成功聚合包覆,用热重分析方法计算其包覆率为8.1 wt%,接枝率为2.5 wt%.亲水性炭黑的表面自由能降低,同时,Payne效应和结合胶含量表明亲水性炭黑粒子与橡胶的相互作用强于亲水性炭黑粒子之间的相互作用.因此,亲水性炭黑/天然橡胶胶乳复合材料的硫化时间变短,转化速度加快,硫化胶的撕裂强度提高了85%,拉伸强度提高了30%,断裂伸长率提高了20%.     

高分子型炭黑分散剂的合成及其性能研究

研究了嵌段型分分子颜料分散剂的合成及其有炭黑分散体系中的分散稳定作用。结果表明，高分子嵌段分散剂在炭黑分散体系中能明显改善分散稳定性。同时发现，嵌段分散剂的组成、结构及分子量对分散作用有综合影响。     

Grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticle and carbon black surfaces

The surface grafting of hyperbranched cyclotriphosphazene polymer onto silica nanoparticles and carbon black was investigated. The grafting of hyperbranched cyclotriphosphazene polymer onto these surfaces was achieved by the repeated reactions of hexachlorocyclotriphosphazene with hexamethylenediamine from surface amino groups and sodium carboxylate groups, respectively. The percentage of grafting onto silica and carbon black surfaces exceeded 760 and 390%, respectively. However, it proved difficult to achieve the theoretical growth of cyclotriphosphazene polymer from these surfaces because of steric hindrance. The introduction of sulfonic acid groups was successfully achieved by the reaction of terminal chlorophosphazene groups of the hyperbranched polymer‐grafted silica and carbon black with sulfanilic acid. The content of sulfonic acid groups introduced onto silica and carbon black surfaces was 4.98 mmol/g and 5.70 mmol/g, respectively. The sulfonated cyclotriphosphazene polymer‐grafted carbon black was extremely hydrophilic, yielding stable colloidal dispersions in polar solvents. The sulfonated cyclotriphosphazene polymer‐grafted silica and carbon black showed ionic conductivity, with the conductance increasing exponentially with increasing relative humidity and temperature. This study may offer important leads in the application of silica nanoparticles and carbon black in polymeric membranes for fuel cells. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4218–4226, 2008     

Radical Graft Polymerization of Vinyl Monomers Initiated by A20 Groups Introduced Onto a Carbon Black Surface: Effect of azo Groups on Graft Polymerization

The radical graft polymerization of vinyl monomers from carbon black initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto carbon black surface was achieved by three methods: the reaction of 2,2′-azobis[2-(2-imidazolin-2-yl)propane] (AIP) with (1) epoxide groups, which were introduced by the reaction of carbon black with chlorometh-yloxirane; (2) acyl chloride groups, which were introduced by the reaction of carboxyl groups on the surface with thionyl chloride; and (3) 3-chloroformyl-1-cyano-1-methylpropyl groups, which were introduced by the reaction of carbon black with 4,4′-azobis(4-cyanovaleric acid) and then thionyl chloride. The amount of azo groups introduced onto the surface by the above methods was determined to be 0.07-0.19 mmol/g. The graft polymerization of methyl methacrylate was found to be initiated by azo groups introduced onto the carbon black surface. During the polymerization, poly(methyl methacrylate) was effectively grafted onto carbon black through propagation of the polymer from the radical produced on the surface by the decomposition of the azo groups. The percentage of grafting using carbon black having azo groups introduced by method 1 increased to 40%. It was also found that the graft polymerization of several vinyl monomers such as styrene, acrylonitrile, and acrylic acid was initiated by the azo groups introduced onto the surface and the corresponding polymer was effectively grafted onto the surface. Furthermore, the effect of the amount of carbon black having azo groups on the graft polymerization was investigated.     

超声引发自由基聚合制备聚苯乙烯磺酸钠接枝炭黑

通过在超声环境下,单体苯乙烯磺酸钠发生自由基聚合,生成的聚合物长链自由基被炭黑表面捕获,制备聚合物接枝炭黑.借助红外光谱、热重、粒度、透射电镜和zeta电位分析对该接枝炭黑进行表征.同时研究超声条件对接枝率的影响.结果表明,单体聚合并接枝到炭黑表面,同时炭黑的附聚体和一些大的聚集体结构被超声破碎,平均粒径大为减小;在300W超声波输出功率下,反应1h后,接枝率达到12.8%并趋于稳定.由于接枝分子链上磺酸基的存在,接枝炭黑在水中的分散稳定性显著改善.     

Graft Polymerization of Vinyl Monomers Onto Carbon Black by Use of the Redox System Consisting of Ceric Ions and Carbon Black Carrying Alcoholic Hydroxyl Groups

The radical graft polymerization of vinyl monomers onto carbon black initiated by a redox system consisting of ceric ion and carbon black having alcoholic hydroxyl groups was investigated. The introduction of alcoholic hydroxyl groups onto the carbon black surface was achieved by the reaction of carbon black with alcoholic hydroxyl radicals, formed by the reaction of alcohol with benzoyl peroxide. The rate of the polymerization of acrylamide (AAm) initiated by the redox system was found to increase in the following order of hydroxyl groups: 1-hydroxyoctyl < 1-hydroxypropyl < 1-hydroxyethyl < hydroxymethyl < 1-hydroxy-1-methylethyl. In the redox polymerization, poly-AAm was effectively grafted onto carbon black by propagation of the polymer from the radical formed by the reaction of ceric ions with the alcoholic hydroxy groups. The percentage of grafting increased with increasing conversion. By use of this redox system, poly(acrylic acid), polyacrylonitrile, and poly(N-vinyl-2-pyrrolidone) could be grafted onto carbon black, but poly(methyl methacrylate) and polystyrene could not be so grafted. The graft polymerization of AAm by use of a redox system consisting of ceric ion and PVA-grafted carbon black was also investigated.     

Heat-Resistant Polymer-Grafted Carbon Black: Grafting of Poly(Organophosphazenes) onto Carbon Black Surface

Abstract

The grafting of poly(organophosphazenes) onto carbon black surface by the reaction of poly(dichlorophosphazene) (PDCP) with carbon black having sodium phenoxide groups was investigated. PDCP was prepared by the ring-opening polymerization of hexachlorocyclotriphos-phazene in solution using sulfamic acid as a catalyst. The introduction of sodium phenoxide groups onto carbon black was achieved by treatment of phenolic hydroxyl groups on the surface with sodium hydroxide in methanol. Poly(diphenoxyphosphazene) (PDPP) was successfully grafted onto carbon black by the reaction of PDCP with sodium phenoxide groups introduced onto the surface followed by the replacement of chlorine atoms in PDCP with phenoxy groups. The percentage of grafting onto carbon black increased to 206% at 30°C after 12 h. It was found that only 1.4% of sodium phenoxide groups on carbon black surface was used for the grafting of PDCP because of the blocking of the surface by grafted polymer chains. Poly(diaminophenylphosphazene) and poly-(diethoxyphosphazene) were also grafted onto carbon black surface by the treatment of PDCP-grafted carbon black with aniline and sodium ethoxide, respectively. Poly(organophosphazenes)-grafted carbon blacks produced stable colloidal dispersions in good solvents for grafted polymers. Furthermore, thermogravimetric analysis indicated that poly-(organophosphazenes)-grafted carbon blacks were stable in air about 300°C.     

Surface Grafting of Phenolic Resole onto LDPE Films

Many studies on surface modification of polymeric membranes have been reported. For example, acrylic acid(shorted as AA) and acrylamide monomers were grafted onto polyethylene, polypropylene and polyethylene terephthalate films in order to minimize the in…     

Heat-Resistant Polymer-Grafted Carbon Black: Grafting of Poly(Amide-Imide) Onto Carbon Black

Aromatic poly(amide-imide) with terminal isocyanate groups (PAINCO) was prepared by the polycondensation of trimellitic anhydride and a slight excess of 4,4′-diphenylmethane diisocyanate in N-methyl-2-pyrrolidone (NMP) at 160°C for 20 h. PAI was effectively grafted onto the surface by the reaction of PAI-NCO with carbon black: the percentage of grafting onto FW 200 and Neospectra II was determined to be 41.2 and 39.5%, respectively. When the carboxyl and phenolic hydroxyl groups on carbon black were blocked by treatment with diazomethane, the grafting of PAI-NCO onto the treated carbon black does not proceed. Therefore, it is concluded that PAI-NCO reacts with the carboxyl and phenolic hydroxyl groups on carbon black and PAI is grafted through amide and urethane bonds, respectively. The reaction of PAI-NCO with carbon black was accelerated by the addition of amines as catalyst and by raising of the reaction temperature. Thermogravimetric analysis indicated that PAI-grafted carbon black was stable in air up to about 300°C. The PAI-grafted carbon black was found to give a stable colloidal dispersion in NMP.     

Cationic grafting from carbon black. VII. Grafting of polyacetals by cationic ring-opening polymerization of trioxane and 1,3-dioxolane initiated by CO+ClO4− groups on carbon black

The cationic ring-opening polymerization of trioxane and 1,3-dioxolane was found to be initiated by CO⁺CIO₄^? groups on a carbon black surface, which were introduced by the reaction of COCI groups with AgCIO₄. The activation energy of the ring-opening polymerization of trioxane was estimated to be 15.5 kcal/mol. In the polymerization system, poly(oxymethylene) and poly(1,3-dioxolane) formed were effectively grafted onto carbon black depending upon the propagation of these polymers from the carbon black surface; for instance, the grafting ratio of poly(oxymethylene) onto carbon black increased with an increase in conversion and went up to about 180%. Although the grafted chain of poly(oxymethylene) was subject to stepwise thermal depolymerization from the chain ends, the thermal stability of poly(oxymethylene)-grafted carbon black was improved by acetylation of hemiformal end groups. The molecular weight of ungrafted poly(oxymethylene) formed in the polymerization was determined to be 1.8–2.0 × 10⁴. Furthermore, the copolymerization of trioxane with 1,3-dioxolane, styrene, and other comonomers initiated by CO⁺CIO₄^? groups and the thermal stability of these acetal copolymer-grafted carbon black were investigated.     

Grafting of hyperbranched poly(amidoamine) onto carbon black surfaces using dendrimer synthesis methodology

To modify carbon black surface, the surface grafting of hyperbranched poly(amidoamine) onto the surface by using dendrimer synthesis methodology was investigated. Carbon black having amino groups (initiator sites) was prepared by the reduction of surface nitro groups introduced by nitration of aromatic rings. It was found that hyperbranched poly(amidoamine) was propagated from carbon black surface by repeating two processes: (1) Michael addition of methyl acrylate (MA) to surface amino groups and (2) amidation of the resulting esters with ethylenediamine: the percentage of poly(amidoamine) grafting reached to 96.2% after 10th‐generation. The grafting of hyperbranched poly(amidoamine) onto polystyrene‐bead as a model compound of carbon black was also achieved by the above procedures. However, the theoretical propagation of poly(amidoamine) dendrimer was not achieved, because of steric hindrance of grafted polymer. Hyperbranched poly(amidoamine)‐grafted carbon black gave a stable dispersion in a good solvent for poly(amidoamine). Copyright © 2001 John Wiley & Sons, Ltd.