钝感炸药DNP和NTO的酸性解离常数的测定方法研究

采用滴定法、半中和法、p H法、电导率法、紫外分光光度法5种方法,测定了3,4-二硝基吡唑(DNP)和3-硝基-1,2,4-三唑-5-酮(NTO)两种钝感炸药的酸性解离常数p Ka,并对不同方法所测的结果进行比较和讨论。结果表明,滴定法、半中和法、紫外分光光度法3种方法适合DNP类物质的p Ka测定,实验结果基本一致,与文献值的相对误差RE5%;滴定法、p H法更适合NTO类物质的p Ka测定,实验结果基本一致,与文献值的相对误差RE4%。DNP的p Ka大于NTO的p Ka,即DNP比NTO的酸性弱,对设备等的腐蚀作用较小,更适宜用作熔铸炸药载体。根据这5种酸性解离常数测定方法的优缺点,讨论了测定不同性质物质的p Ka时可选用的方法。     

AGNTO的制备和分子结构

通过3-硝基-1,2,4-三唑-5-酮（NTO）与氨基胍重碳酸盐反应制备NTO氨基胍盐,并用X射线衍射、元素分析、红外光谱对其进行了表征.晶体属于单斜晶系,空间群为P21/n.晶体学参数为：a=0.67870(10)nm, b=2.7915(4)nm, c=1.2739(2)nm; β =96.930(10) V=2.3959(6)nm3, Z=12, Dc=1.698 g•cm －3, μ( Mo K )=1.47 cm －1, F(000)=1272.晶体结构经全矩阵最小二乘法修正,最终偏离因子R=0.0352, wR =0.0718.该盐是一种具有广泛应用前景的产气剂材料.     

HMX晶体和HMX/F2311 PBXs力学性能的MD模拟研究

用分子动力学方法, 在295 K NVT系综和COMPASS力场下, 对环四甲撑四硝胺(HMX)晶体和F₂₃₁₁沿HMX (001), (010)和(100)晶面所构成PBXs模型的力学性能进行模拟研究. 结果表明, 加入F₂₃₁₁降低了HMX的刚性, 增强了它的延展性. 在HMX (100)面上添加F₂₃₁₁对提高体系的延展性较显著. 为考察温度对力学性能的影响及其机理, 在245～445 K范围完成对HMX (100)/F₂₃₁₁ PBX的MD模拟. 力学分析表明, 随温度增加HMX (100)/F₂₃₁₁的延展性呈抛物线变化规律, 归因于F₂₃₁₁分子链的运动及其构象随温度的变化.     

3-硝基-1,2,4-三唑-5-酮与NH3及H2O分子间相互作用的理论研究

在DFT-B3LYP/6-311＋＋G**水平上, 求得3-硝基-1,2,4-三唑-5-酮(NTO)/NH₃和NTO/H₂O两种超分子体系势能面上5种全优化构型. 经基组叠加误差(BSSE)和零点能(ZPE)校正, 求得NTO与NH₃和H₂O的分子间最大相互作用能依次为－37.58和－30.14 kJ/mol, 表明NTO与NH₃的分子间相互作用强于与H₂O的作用. 超分子体系中电子均由NH₃或H₂O向NTO转移, 相互作用能主要由强氢键所贡献, 由自然键轨道分析揭示了相互作用的本质. 对优化构型进行振动分析, 并基于统计热力学求得200.0～800.0 K温度范围从单体形成超分子的热力学性质变化. 发现由NTO和NH₃形成超分子II和III在常温下可自发进行; 而NTO和H₂O只在低温下才能自发形成IV, V和VI超分子.     

Ni-Cu作用对于1,4-丁炔二醇一步法低压加氢的影响

采用沉积沉淀法将金属助剂引入Ni/Al₂O₃催化剂,考察不同金属助剂对于BYD加氢体系的影响,进一步优选助剂的最佳含量,并结合BET、XRD、H₂-TPR、EDX-MAPPING、TEM、XPS、NH₃-TPD等表征手段对催化剂物化性质进行研究。结果表明,金属助剂的添加主要影响了活性组分与载体间相互作用,成为影响催化活性的主要原因。Cu与Fe的引入使催化剂中Ni²⁺与载体之间相互作用明显减弱,提高了还原性能,BYD转化率提高至95%。通过考察优选金属助剂Cu含量对于催化剂物化性质的影响,发现使Ni²⁺与载体间相互作用力减弱的主要原因在于Cu表面氢溢流现象,然而,较多还原后的Ni颗粒由于与载体间的弱相互作用,易发生团聚,对加氢过程造成不利影响,通过Ni-Cu金属作用可有效地将金属固定于在载体表面,避免粒子迁移、团聚,Cu添加量5%时,催化剂凭借较多分散度良好的活性组分和适宜酸性,最终表现出最优加氢性能。     

分子动力学模拟烷烃混合物在石墨烯表面取向

采用分子动力学模拟方法研究了烷烃混合物在石墨烯表面取向的过程.研究结果表明,模拟温度能够改变链取向的方向,相对较低的温度对链垂直表面取向有利,相对较高的温度对链平行于表面取向有利;温度升高短链烷烃会发生脱离混合物的情况,且温度越高发生脱离行为的烷烃数目越多.烷烃链与石墨烯的相互作用在此过程中起重要作用.     

左旋聚乳酸/聚(ε-己内酯)共混物在取向聚乙烯基底上的附生结晶行为

利用电子显微镜结合电子衍射研究了左旋聚乳酸/聚(ε-己内酯)(PLLA/PCL)共混物在取向聚乙烯(PE)基底上的结晶行为.纯PLLA在取向PE基底上能够附生结晶,主要形成分子链相互垂直的片晶结构.PCL在PE基质上也能发生附生结晶,导致两者分子链平行.PLLA/PCL共混物在取向PE基底上结晶的形态结构依赖于共混组成.在PLLA含量大于95 wt%时,PCL不影响PLLA与PE的附生结晶行为.当PCL含量增加至10 wt%时,PLLA在PE上的附生结晶行为受到了一定程度的影响.当PCL含量超过40 wt%时,PLLA在PE上的附生结晶被抑制,取而代之是PCL在PE取向基质上附生结晶,产生两者分子链平行的取向片晶.另外,在PLLA含量在50 wt%~30 wt%之间时,体系产生明显的微相分离,微相分离并不影响PCL与PE的附生结晶,在PCL的富集区仍然发生平行链附生结晶,而PLLA的富集区结构变得模糊.当PLLA含量少于20 wt%时,微相分离不明显,少量PLLA应该分散在PCL片晶间的非晶区.     

不同链长烷烃在碳纳米管表面行为的分子动力学模拟

采用分子动力学方法模拟了不同长度的烷烃在单壁碳纳米管表面的吸附和取向过程,直观地给出了过程中很多微观信息,如链与纳米管管轴的夹角,链的弯曲程度等.结果表明短链烷烃能够被吸附在纳米管表面并沿着特定的方向取向;碳纳米管表面起到诱导取向的作用,并且该诱导作用对离表面最近的吸附层作用最明显;在吸附过程中,烷烃链发生弯曲,而吸附以后,取向的烷烃链倾向于采取伸直的状态。     

聚(对亚苯基-1,3,4-噁二唑)纤维表面氟化处理研究

采用氟气(F2)对聚(对亚苯基-1,3,4-噁二唑)(p-POD)纤维表面进行直接氟化处理.衰减全反射红外光谱(ATR-FTIR)和表面电子能谱(XPS)的结果显示,通过直接氟化处理,p-POD纤维较易与F2发生反应,表面大分子链上引入了大量C—F键,表面氟元素含量高达28.2%,且F原子以—CF/C O、—CFH及—CF2形式存在,表明在表面氟化过程中,既有取代反应,也有加成反应.热失重(TGA)结果表明氟化前后p-POD纤维的耐高温性能没有受到影响,X射线衍射图谱(XRD)表明氟化后纤维的聚集态有序性略微增加.氟化前后纤维的断裂强度基本无变化,在体积分数为20%的硫酸溶液中的人工加速酸老化条件下,氟化后纤维在老化120 h后的断裂强力保留率在80%以上,相比氟化前的纤维提高了约90%,即耐酸性得到明显改善.推测表面氟化处理改善p-POD纤维耐酸性的机理是氟化后p-POD纤维表面N元素含量降低,抑制了溶剂化过程;纤维表面致密程度得到提高以及F原子与酸液形成氢键,从而阻止噁二唑环的质子化,延缓了老化进程.     

络合作用对重油加氢处理催化剂性能的影响

以Ni、W为催化剂的活性金属组分,考察在金属组分浸渍液中加入有机络合剂对催化剂性质及加氢脱硫、脱氮性能的影响。结果表明,络合剂与金属组分共浸渍更有利于金属组分的分散;提高络合剂用量,既有利于提高主活性金属组分WO₃在载体表面的分散,又能促进六配位八面体Ni物种及高加氢活性相NiWO₃的形成;焙烧温度具有调变催化剂金属组分分散性及酸性的双重作用,在适宜的焙烧温度下制得的催化剂具有较好的酸性及加氢活性,主要表现为较高的加氢脱硫及脱氮活性。     

氨基酸缓蚀剂在盐酸溶液中对钢的缓蚀作用

应用极化曲线、电化学阻抗谱等测试技术,研究了以谷氨酸作缓蚀剂在10%盐酸介质中对X65钢的缓蚀作用,测试腐蚀参数包括腐蚀电位(Ecorr)、极化电阻(Rp)、缓蚀效率(η)等.研究表明:该缓蚀剂是一种抑制阴极为主的混合型缓蚀剂,在较低的浓度具有良好缓蚀效果;缓蚀效率随着浓度的增加而提高,并在0.3g.L-1时达到最大值(90%以上).     

咪唑啉衍生物与硫脲之间的缓蚀协同效应研究

应用失重法、动电位扫描法、X射线光电子能谱(XPS)研究了咪唑啉缓蚀剂和硫脲复配后对碳钢在CO2盐水溶液中的缓蚀协同作用.实验表明,咪唑啉和硫脲之间存在着良好的协同效应,二者复合后对CO2腐蚀有较好的抑制作用.经XPS检测,试样表面吸附膜有N、S元素存在,而且,于接近基体处,S元素含量相对较高;而在溶液界面处,则N元素含量较高.据此推断缓蚀剂和硫脲在钢样表面可能形成"包含络合物",从而使缓蚀剂膜更加致密,缓蚀效果也更好.     

溴化十六烷基吡啶自盐酸溶液中在铝表面上的吸附及其缓蚀作用

用失重法研究了溴化十六烷基呲啶对铝在盐酸溶液中的缓蚀作用, 应用吸附理论和Sekine方法处理实验数据~[4], 发现溴化十六烷基吡啶自盐酸溶液中在铝表面上产生了吸附, 且基本服从Langmuir吸附等温式。求得吸附热为35.4 kJ mol~(-1), 认为这种吸附是产生缓蚀作用的重要原因。实验还表明, 缓蚀率随温度升高而增大, 根据这些结果讨论了吸附与缓蚀作用之间的关系。     

Adsorption and migration growth of the Ce,O, and F adatoms on the CeO2 (111) surface: A density functional theory study

In order to investigate the microscopic behavior of the crystal surface growth of the fluorinated cerium dioxide polishing powder, the adsorption and migration of the Ce, O, and F atoms on the CeO₂ (111) surface were studied by using density functional theory with Hubbard correction +U. The adsorption energies of three single atoms at five high-symmetry sites and the migration activation energies along the migration pathway on the CeO₂ (111) surface were calculated. Results show that the most stable adsorption sites of the Ce, O, and F atoms were the O_h, Ce_bri, and Ce_t sites, respectively. The Ce atom migrated from the O_h to the O_t site. The O atom migrated from the Ce_bri to the O_bri site. The F atom migrated from the Ce_t to the O_h site. The migration activation energies of the Ce, O, and F atoms along the migration pathways were 1.526, 0.597, and 0.263 eV, respectively. The F adatom does not change the spatial configuration of the Ce and the O atoms. When the O vacancy occurs on the CeO₂ (111) surface, the F adatom can make up for the O vacancy defect.     

Corrosion inhibition and adsorption behavior of methionine on mild steel in sulfuric acid and synergistic effect of iodide ion

The corrosion inhibition of mild steel in sulfuric acid by methionine (MTI) was investigated using electrochemical techniques. The effect of KI additives on corrosion inhibition efficiency was also studied. The results reveal that MTI inhibited the corrosion reaction by adsorption onto the metal/solution interface. Inhibition efficiency increased with MTI concentration and synergistically increased in the presence of KI, with an optimum [KI]/[MTI] ratio of 5/5, due to stabilization of adsorbed MTI cations as revealed by AFM surface morphological images. Potentiodynamic polarization data suggest that the compound functioned via a mixed-inhibition mechanism. This observation was further corroborated by the fit of the experimental adsorption data to the Temkin and Langmuir isotherms. The inhibition mechanism has been discussed vis-à-vis the presence of both nitrogen and sulfur atoms in the MTI molecule.     

环糊精包合有机磷酸作为缓蚀剂的理论研究

采用分子模拟对三种有机磷酸(5-单磷酸腺苷(A)、羟基乙叉二磷酸(B)、2-磷酸基-1, 2, 4-三羧酸丁烷(C))及其与阳离子改性的β-环糊精(HPTEA-β-CD)形成的包合物作为缓蚀剂进行了理论研究,并通过失重法进行了实验验证.量子化学的计算结果表明,三种有机磷酸分子的反应活性主要集中在N、O、P等原子上,其中C分子的反应活性更强.同时采用分子动力学模拟HPTEA-β-CD包合A、B、C分子作为缓蚀剂在Fe(001)表面上的平衡吸附,结果表明C-HPTEA-β-CD的缓蚀效率最强.通过失重法分析,三种缓蚀剂对q²35碳钢均有良好的缓蚀性,其中C-HPTEA-β-CD的缓蚀效率最高,达到了91.50%,实验结果与理论计算的分析一致.     

Cathodic etching for fabrication of super-hydrophobic aluminum coating with micro/nano-hierarchical structure

A facile method for fabricating super-hydrophobic surfaces on the magnetron sputtering aluminum film by cathodic electrochemical etching followed by the modification of myristic acid was presented in this article. The morphologies and the compositions of the films were characterized by means of scanning electron microscopy (SEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS), respectively. The corrosion behavior of the super-hydrophobic film was evaluated by potentiodynamic polarization measurement, linear polarization measurement, and electrochemical impedance spectroscopy. After the treatment with cathodic electrochemical etching, the thin aluminum film remained unbroken and the bulk structure of the aluminum coating maintained a microcrystalline morphology while the surface of the coating presented a petal-shaped microstructure dotted with nano-sized floccules. Aluminum myristate was formed on the nano/microstructural surface of the coating when the sample was modified in melting myristic acid. The static water contact angle on the surface was larger than 165°, which demonstrated that a super-hydrophobic film was prepared on the magnetron sputtering aluminum coating. The corrosion resistance of the aluminum coating was enhanced remarkably because of the super-hydrophobic modification.     

Molecular Dynamics Simulations for Effects of Fluoropolymer Binder Content in CL-20/TNT Based Polymer-Bonded Explosives

In order to better understand the role of binder content, molecular dynamics (MD) simulations were performed to study the interfacial interactions, sensitivity and mechanical properties of 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane/2,4,6-trinitrotoluene (CL-20/TNT) based polymer-bonded explosives (PBXs) with fluorine rubber F₂₃₁₁. The binding energy between CL-20/TNT co-crystal (1 0 0) surface and F₂₃₁₁, pair correlation function, the maximum bond length of the N–NO₂ trigger bond, and the mechanical properties of the PBXs were reported. From the calculated binding energy, it was found that binding energy increases with increasing F₂₃₁₁ content. Additionally, according to the results of pair correlation function, it turns out that H–O hydrogen bonds and H–F hydrogen bonds exist between F₂₃₁₁ molecules and the molecules in CL-20/TNT. The length of trigger bond in CL-20/TNT were adopted as theoretical criterion of sensitivity. The maximum bond length of the N–NO₂ trigger bond decreased very significantly when the F₂₃₁₁ content increased from 0 to 9.2%. This indicated increasing F₂₃₁₁ content can reduce sensitivity and improve thermal stability. However, the maximum bond length of the N–NO₂ trigger bond remained essentially unchanged when the F₂₃₁₁ content was further increased. Additionally, the calculated mechanical data indicated that with the increase in F₂₃₁₁ content, the rigidity of CL-20/TNT based PBXs was decrease, the toughness was improved.     

玉米醇溶蛋白/十二烷基硫酸钠复合物对碳钢的缓蚀效应

通过失重法、扫描电镜和极化曲线法研究了玉米醇溶蛋白/十二烷基硫酸钠(zein/SDS)复合物对碳钢的缓蚀效应。在1mol/L盐酸溶液中,加入0.05‰zein对碳钢的缓蚀率为65.5%,而加入zein/SDS复合物(0.05‰zein+0～8mmol/L SDS)能够使碳钢的缓蚀率逐渐增高至90.1%。随着zein/SDS复合物中SDS浓度的增大,碳钢表面逐渐由深坑面腐蚀变为局部点腐蚀,最终趋于平整。极化曲线测试表明,zein/SDS复合物能够有效抑制碳钢表面电极反应的发生。纯zein与碳钢表面吸附的ΔG_(ads)值表明,zein在碳钢表面主要发生静电吸附作用,而zein/SDS复合物对碳钢的缓蚀效应主要来源于zein同碳钢表面之间的配位吸附作用,这是由于SDS类胶束之间的静电斥力引起zein空间构象的改变。     

Electrospinning of a functional perfluorinated block copolymer as a powerful route for imparting superhydrophobicity and corrosion resistance to aluminum substrates

Superhydrophobic aluminum surfaces with excellent corrosion resistance were successfully prepared by electrospinning of a novel fluorinated diblock copolymer solution. Micro- and nanostructuration of the diblock copolymer coating was obtained by electrospinning which proved to be an easy and cheap electrospinning technology to fabricate superhydrophobic coating. The diblock copolymer is made of poly(heptadecafluorodecylacrylate-co-acrylic acid) (PFDA-co-AA) random copolymer as the first block and polyacrylonitrile (PAN) as the second one. The fluorinated block promotes hydrophobicity to the surface by reducing the surface tension, while its carboxylic acid functions anchor the polymer film onto the aluminum surface after annealing at 130 °C. The PAN block of this copolymer insures the stability of the structuration of the surface during annealing, thanks to the infusible character of PAN. It is also demonstrated that the so-formed superhydrophobic coating shows good adhesion to aluminum surfaces, resulting in excellent corrosion resistance.