碱液回流老化ZrO(OH)_2制备纳米晶ZrO_2的影响因素

通过考察回流老化所用的碱液（NH_4OH, NaOH和KOH）介质和容器材质（玻璃 和Teflon）对ZrO(OH)_2凝胶及其焙烧产物ZrO_2的织构／结构和热稳定性的影响， 研究了杂质元素掺杂和凝胶溶解－再沉淀等因素在形成高表面积纳米晶ZrO(OH) _2/ZrO_2过程中的作用。在Teflon容器中，以NH_4OH为介质（pH = 11.5）的回流 老化对ZrO(OH)_2/ZrO_2的性质无明显影响。而使用玻璃容器则可显著提高ZrO(OH) _2/ZrO_2的表面积、孔容和抗烧结性质，并在800℃获得小晶粒（5～7 nm）四方晶 相ZrO_2纳米晶材料；在DTA曲线上ZrO(OH)_2转变成ZrO_2晶体的温度由回流老化前 的463℃提高到810～840℃。在以KOH和NaOH为介质(pH = 13)的实验中，使用玻璃 容器得到与经NH_4OH为介质时相类似的结果；但在Teflon容器中只形成低表面积和 较大尺寸（约20 nm）以单斜相为主的混合晶相ZrO(OH)_2，其在800℃焙烧后形成 大晶粒（35 nm）单斜相ZrO_2。样晶的元素分析结果清楚地揭示出使用玻璃容器时 有SiO_2从器壁溶解掺杂进入ZrO(OH)_2凝胶。样品的表面积和孔容与杂质Si~(4+) 含量之间有顺变关系，表明Si~(4+)掺杂是形成高表面积和大孔容ZrO(OH) _2/ZrO_2、提高ZrO_2晶化温度以及稳定小晶粒四方晶相ZrO_2的最主要因素。在不 发生Si~(4+)掺杂前提下，K~+和Na~+的存在可促进ZrO(OH)_2形成结晶，但对高温 下ZrO_2织构的稳定性影响不大。此外，ZrO(OH)_2凝胶的溶解－再沉淀和骨架网络 有序化也是回流老化影响ZrO(OH)_2/ZrO_2织构的重要因素。     

B2O3/TiO2-ZrO2催化环己酮肟气相Beckmann重排反应研究 Ⅰ.B2O3含量的影响

 制备了不同B2O3含量（0～20％）的B2O3／TiO2－ZrO2固体酸催\r\n化剂，用XRD，FT－IR，N2吸附及NH3－TPD等方法测定了其结构、比表\r\n面积、孔分布和表面酸性．结果表明，当B2O3含量较低（≤5％）时，\r\n催化剂呈无定形态，样品中的B2O3主要以BO4结构存在．当B2O3含量较\r\n高（≥8％）时，催化剂中的TiO2－ZrO2以ZrTiO4晶相存在，分散于Ti\r\nO2－ZrO2表面的B2O3主要以玻璃体形式和BO3结构存在．随着B2O3含量\r\n的增加，催化剂的比表面积减小，孔径增大．300℃下的环己酮肟气相\r\nBeck－mann重排反应结果表明，随着B2O3含量的增加，己内酰胺的选择\r\n性逐渐增大，而己内酰胺的收率在B2O3含量为12％时达到最大值．讨论\r\n了B2O3／TiO2－ZrO2的催化性能与其表面酸性及孔径大小的关系．     

三维规则排列的大孔SiO2材料的制备及表征

 以聚苯乙烯微球离心后形成的三维规则排列的胶晶作模板，以正\r\n硅酸乙酯、水、乙醇和盐酸等配制的溶胶填充微球间的间隙，然后原位\r\n形成凝胶，最后通过焙烧除去微球得到三维规则排列大孔二氧化硅材料\r\n．以苯乙烯为原料，过硫酸钾为引发剂，在70℃下搅拌28h后得到含聚\r\n苯乙烯微球（直径约为600nm）的母液．将母液在900～1000r／min的转\r\n速下离心12～24h得到紧密堆积排列的胶晶．以正硅酸乙酯作为硅源，\r\n按n（Si（OEt）4）∶n（EtOH）∶n（HCl）∶n（H2O）＝1∶3．9∶0．\r\n3∶1．8制成透明的SiO2溶胶．溶胶浓度控制在0．5～1．0mol／L．滴\r\n加在胶晶上的溶胶靠毛细管的作用力填充入微球间隙．重复填充多次（\r\n一般不超过5次）．焙烧在流量为1L／min的空气中进行，升温速度控制\r\n在5℃／min以下．在300℃下恒温5h以除去聚苯乙烯微球，在570℃下焙\r\n烧5h．焙烧后的样品表面可观察到五颜六色的彩光．SEM分析结果表明\r\n，球形孔（孔径约500nm）大小均匀，排列整齐，保持了微球的紧密堆\r\n积排列结构．孔与孔之间由小孔窗相互交连，孔壁比较充实，壁厚约为\r\n130nm．     

纳米二氧化锆催化剂上一氧化碳加氢合成异丁烯

 考察了纳米ZrO2的制备方法及Al2O3和KOH助剂的添加对ZrO2催化\r\nCO加氢合成异丁烯反应的影响．纳米ZrO2的制备方法对ZrO2的物理性质\r\n和催化性能有较大的影响．用超临界流体干燥法干燥并在流动N2气氛中\r\n焙烧制得的ZrO2催化剂对异丁烯具有较高的选择性．Al2O3和KOH助剂表\r\n现出非常优良的助剂效应，在大幅度提高催化剂对i－C4烃选择性的同\r\n时保持了和ZrO2同样高的催化活性．催化剂的酸碱性表征结果表明，酸\r\n碱性对催化剂的催化性能影响很大，催化剂上适宜的酸碱数量和酸碱比\r\n例是影响其催化CO加氢合成异丁烯性能的非常重要的因素．     

制备方法对Pd催化剂上丙烯选择性还原NO反应性能的影响

 采用三种不同方法制备了氧化铝负载的Pd催化剂．比表面积测定\r\n结果表明,与浸渍法相比,溶胶－凝胶加浸渍法和溶胶－凝胶法制备的\r\nPd／Al2O3样品具有较大的比表面积,但抗烧结性能不佳．其中采用溶\r\n胶－凝胶法制备的样品中,由于Pd分散于体相中,表面的活性位相对较\r\n少,造成催化剂在NO选择性还原反应中的活性较差;而将Pd浸渍于溶胶\r\n－凝胶法制得的Al2O3载体上所获得的催化剂比表面积较大,活性较好\r\n．添加CeO2的样品活性总体上比Pd／Al2O3样品高．其中采用溶胶－凝\r\n胶法制备的样品比表面积不大,并且XRD数据表明Al2O3和CeO2是高度分\r\n散并均匀地搀杂在一起的,不象在浸渍法制备的样品中那样以大晶粒的\r\n形式存在,因而CeO2的助剂作用没有充分体现出来,催化剂的活性比浸\r\n渍法制备的样品差一些．     

氧化铝负载钌基氨合成催化剂的制备条件及载体改性

 利用等体积浸渍法制备了氧化铝负载钌基氨合成催化剂．考察了\r\n氢氧化铝的焙烧温度，催化剂的还原温度，助剂K、Ba和Sm的添加，以\r\n及用MgO和BaO改性氧化铝载体等对催化剂活性的影响．通过XRD，N2物\r\n理吸附和CO2化学吸附等方法表征了载体的物相结构、比表面积和表面\r\n碱性．研究结果表明，氧化铝表面碱性随着氢氧化铝焙烧温度的升高而\r\n增大是催化剂活性升高的主要原因，载体比表面积的降低对催化剂活性\r\n的影响相对较小．助剂K、Ba和Sm的加入显著地提高了催化剂的活性，\r\n同时助剂Ba和Sm还减弱了强吸附氢对氮吸附的抑制作用，明显提高了催\r\n化剂的高压活性．用MgO改性氧化铝载体降低了其比表面积，但是显著\r\n地提高了载体的表面碱性和催化剂的活性．BaO改性的氧化铝载体的比\r\n表面积、表面碱性及其负载的钌基催化剂的活性随着BaO含量的增加先\r\n升高后降低，当BaO摩尔含量为7．7％时，催化剂活性最高．     

四乙基溴化铵-氟化物复合模板剂合成β沸石 Ⅲ.结晶动力学及其影响因素

 考察了用四乙基溴化铵－氟化钠复合模板剂合成β沸石的结晶动\r\n力学．结果表明：其晶化曲线为典型的S形曲线；成核活化能En＝65．\r\n79kJ／mol，生长活化能Ec＝91．49kJ／mol；与单纯的四乙基溴化铵模\r\n板剂体系相比，本体系成核诱导期较短，生长速率较快；n（NaF）／n\r\n（SiO2）值增大时，晶化诱导期缩短，成核速率加快，但氟化钠量过高\r\n时，成核速率反而降低，n（NaF）／n（SiO2）最佳值为0．10～0．17\r\n；较高的OH－／SiO2比有利于缩短晶化诱导期．     

高渗透性能丝光沸石膜的合成及在醇/水分离体系中的应用

 以四乙基溴化铵为模板剂，用原位水热合成法在α－Al2O3陶瓷\r\n管上合成出丝光沸石膜，系统研究了合成母液的组成、晶化时间、老化\r\n时间、硅源和铝源以及氟化钠助剂的添加等因素对丝光沸石膜成膜和表\r\n面形貌的影响．结果表明，老化可使成膜沸石的晶粒从30μm减小到5μ\r\nm；添加氟化钠也能减小晶粒的大小；使用异丙醇铝为铝源能制得高度\r\n定向的丝光沸石膜．提出了丝光沸石膜的成膜机理，认为成核发生在载\r\n体表面，凝胶层的晶化过程是从载体的表面开始,不断转化,充分生长后达到凝胶层的表面. 丝光沸石膜对醇/水混合体系的分离研究表明,水/甲醇、水/乙醇、水/正丙醇和水/异丙醇的分离因子分别可达到1500(323 K,水含量xw=15%),4200(343 K,xw=15%),4200(343 K,xw=50%)和3400(343 K,xw=50%),所合成的丝光沸石膜能选择性地透过水,对醇/水混合物有较高的分离系数.     

制备蜂窝状筛网进行NH3选择性催化还原NO的反应

 制备了蜂窝状筛网催化剂，并用于以NH3为还原剂选择性催化还\r\n原NO的反应．蜂窝状筛网催化剂具有热响应迅速、传质系数较高、压力\r\n降适中、机械强度较高、几何可变形性、抗热震性能好、催化剂回收简\r\n便和成本较低等一系列优点．阐述了蜂窝状筛网催化剂的制备工艺，并\r\n采用扫描电镜、比表面积测定、X射线衍射、活性评价等手段考察了筛\r\n网预处理方法对其催化活性的影响．实验结果表明，最佳的预处理方法\r\n是首先经稀酸刻蚀，然后于500℃下焙烧20h．     

CeO2-ZrO2复合氧化物对金属蜂窝整体催化剂性能的影响

 用浸渍法制备了不同比例的CeO2－ZrO2复合氧化物，并用XRD，H2－TPR和BET等研究了复合氧化物的晶相、还原性能及热稳定性．结果表明，所制备的CeO2－ZrO2复合氧化物形成了固溶体，Ce0．6Zr0．4O2比Ce0．90Zr0．10O2更容易被H2还原；1100℃老化后，晶胞参数无明显变化，比表面积仍有11．8m2／g．模拟二冲程摩托车尾气组成，对用贵金属Pt，Pd，Rh与CeO2及CeO2－ZrO2固溶体所制备的催化剂进行了活性评价．结果显示，1100℃老化后，催化剂仍具有很高的氧化活性．在贫氧区，Pt－Pd－Rh／Ce0．6Zr0．4O2－Al2O3对碳氢化合物氧化的催化活性则有一定的优势，是一种具有较高热稳定性的催化剂．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.