Sodium tracer diffusion in glasses of the type (Na2O)0.2[(BO1.5)x(SiO2)1 − x]0.8

Sodium tracer diffusion coefficients, D_Na*, have been measured in sodium borosilicate glasses of the type (Na₂O)_0.2[(BO_1.5)_x(SiO₂)_1 − x]_0.8 as a function of temperature and the composition parameter x. In these glasses, which can alternatively also be described by using the formula Na₂O·(2B₂O₃)_x·(4SiO₂)_1 − x, one network former unit, SiO₂, is replaced by another one, BO_1.5, while keeping the sodium concentration constant. At constant temperature, the tracer diffusion coefficient of sodium as a function of x has a shallow minimum at about x = 0.7. At temperatures below about 310 °C the temperature dependences of the measured tracer diffusion coefficients are of Arrhenius-type; at higher temperatures one observes an increase in the temperature dependence with increasing temperature. The activation energy derived from sodium tracer diffusion data for temperatures up to about 310 °C increases about linearly with increasing x from about 70 to 80 kJ/mol. The pre-exponential factor as a function of x varies by about one order of magnitude and has a minimum at about x = 0.4. Values derived for the Haven-ratio are smaller than one and show a shallow minimum as a function of x at around x = 0.75. Furthermore, it was investigated whether there is a significant, directly measurable uptake of water during annealing in moist atmospheres and whether water taken up from moist atmospheres can influence the diffusion of sodium.     

Sodium tracer diffusion in glasses of the type (CaO·Al2O3)x(2 SiO2)1−x

Tracer diffusion coefficients of the radioactive isotope Na-22 were measured in glasses of the type (CaO·Al₂O₃)_x(2 SiO₂)_1−x to study the diffusion of sodium as a function of glass composition, x, temperature and initial water content. The diffusion of Na-22 in glasses diffusion-annealed in dry air can always be well described by a single tracer diffusion coefficient, but sometimes not in samples annealed in common air. It was found that the sodium tracer diffusion coefficient decreases by about six orders of magnitude when the glass composition x changes from 0 to 0.75 at 800 °C. The temperature dependence of the diffusion of sodium seems to decrease as the silica content increases. Variations of the initial water content in some of the glasses investigated did not very significantly influence the rate of the tracer diffusion of sodium.     

Ionic conduction, diffusion and glass transition in 0.2[XNa2O · (1−X)Rb2O] · 0.8B2O3

We have investigated the ionic transport in the 0.2[XNa₂O · (1−X)Rb₂O] · 0.8B₂O₃ mixed-alkali system with X=0.0, 0.2, 0.4, 0.6, 0.8, and 1.0 in the glassy and the undercooled-liquid state by means of impedance spectroscopy and tracer diffusion experiments. The calorimetric glass-transition temperature T_g obtained by differential scanning calorimetry shows a minimum with composition. The composition dependence of the electrical conductivity below T_g exhibits a minimum, as well. These deviations from an ‘ideal’ linear mixing rule are usually denoted as mixed-alkali effect. The dc conductivities times temperature σ_dc×T follow the Arrhenius law in the range below and above T_g, respectively. The glass transition appears as a kink in the Arrhenius presentation of σ_dc×T. Below the glass-transition temperature the onset frequency ν_on of the conductivity dispersion has an Arrhenius-like temperature dependence. According to ‘Summerfield scaling’ the activation enthalpies of σ_dc×T and ν_on are expected to be the same. This is indeed observed but only for the single-alkali compositions. The activation enthalpies of σ_dc×T as a function of composition show a classical mixed-alkali maximum, however the activation enthalpies of the onset frequencies as a function of composition exhibit a nearly constant behavior in contrast to the expectation from Summerfield scaling. The tracer diffusion measurements reveal a major difference in diffusion of ⁸⁶Rb and ²²Na in mixed-alkali glasses. A diffusivity crossover of tracer diffusion coefficients of ²²Na and ⁸⁶Rb occurs near X=0.2. By comparison of tracer and conductivity diffusivities the Haven ratio is deduced which shows a maximum near the conductivity minimum composition.     

Combined in-situ SAXS/WAXS and HRTEM study on crystallization of (Cu60Co40)1 − xZrx metallic glasses

CuZr as well as CoZr are well known metallic glass-formers in a wide compositional range. Since the binary Cu-Co system exhibits a metastable liquid-liquid miscibility gap, i.e. Cu and Co tend to separate from each other, the ternary Cu-Co-Zr system is a promising candidate to form phase separated glass-glass composites. In this work (Cu₆₀Co₄₀)_1 − xZr_x metallic glasses with relatively low Zr contents of x = 37 and x = 32 were prepared by melt spinning and investigated by in-situ small-angle and wide-angle X-ray scattering (SAXS/WAXS) and differential scanning calorimetry (DSC). Certain heat treated samples were additionally investigated by high-resolution transmission electron microscopy (HRTEM). Even for x = 32 there are no indications for any kind of phase separation in the as-quenched state within experimental resolution, i.e. the critical temperature T_c for a liquid-liquid phase separation has already decreased from 1556 K for binary Cu₆₀Co₄₀ to a temperature below the glass transition temperature T_g = 762(5)K found for (Cu₆₀Co₄₀)₆₈Zr₃₂. Combined in-situ SAXS/WAXS and HRTEM investigations reveal that thermal annealing also does not induce an amorphous-amorphous phase separation. Instead the formation of nano crystallites of a so far unknown Cu-rich/Zr-poor phase with relatively low activation energy for crystallization E_a = 116(7) kJ/mol at temperatures far below the crystallization temperature deduced from DSC measurements is observed.     

Thermal dissolution of Ag(Cu) in amorphous Ge(Sx Se1 − x)2 system

Thermally induced solid state reaction of Ag(Cu) into thin Ge(S_x Se_1 − x)₂ films with x = 0, 0.1, 0.4 and 1.0 was investigated using a step by step technique in order to design films with exact Ag(Cu) concentrations for applications in integrated IR optical devices. A thin film of Ag(Cu) was deposited on top of the host Ge(S_x Se_1 − x)₂ films followed by annealing in vacuum at constant temperature, which resulted in homogeneous films of good optical quality. The variation in Ag(Cu) concentration in the films ranged between 5 and 35 at.%. The kinetics of the diffusion and dissolution of metal in the host films was measured by optically monitoring the change in thickness of doped chalcogenide during consecutive thermal annealing steps. The kinetics studies revealed that the thermal dissolution rate of the Cu is greater than that of Ag. Optical UV-VIS transmission spectra of chalcogenide glass layers, undoped and thermal doped by Ag(Cu), were measured to establish the optical properties of the films. The spectra were analyzed using the technique proposed by Swanepoel and the results show that the addition of metal increases the absorption coefficient in the power-law regime and consequently the optical gap decreases and the refractive index increases. The amorphous character of the films was checked by X-ray diffraction which confirmed the amorphous structure of all Ag(Cu)GeSSe thin films.     

Crystallization behavior of (GeS2)0.1(Sb2S3)0.9 glass

The crystal growth kinetics of antimony trisulfide in (GeS₂)_0.1(Sb₂S₃)_0.9 glass has been studied by microscopy and DSC. The linear crystal growth kinetics has been confirmed in the temperature range 492 ? T ? 515 K (E_G = 405 ± 7 kJ mol⁻¹). The applicability of standard growth models has been assessed. From the crystal growth rate corrected for viscosity plotted as a function of undercooling it has been found that the most probable mechanism is interface controlled 2D nucleated growth. The non-isothermal DSC data, corresponding to the bulk sample, can be described by the Johnson-Mehl-Avrami equation.     

The effect of composition on UV-vis-NIR spectra of iron doped glasses in the systems Na2O/MgO/SiO2 and Na2O/MgO/Al2O3/SiO2

Glasses with the compositions xNa₂O · 10MgO · (90 − x)SiO₂, 10Na₂O · xMgO · (90 − x)SiO₂, 5Na₂O · 15MgO · xAl₂O₃ · (80 − x)SiO₂, xNa₂O · 10MgO · 10Al₂O₃ · (80 − x)SiO₂, 10Na₂O · 10MgO · xAl₂O₃ · (80 − x)SiO₂, 10Na₂O · 5MgO · 10Al₂O₃ · (80 − x)SiO₂ were melted and studied using UV-vis-NIR spectroscopy in the wavenumber range from 5000 to 30 000 cm⁻¹. At [Al₂O₃] > [Na₂O], the UV-cut off is strongly shifted to smaller wavenumbers and the NIR peak at around 10 000 cm⁻¹ attributed to Fe²⁺ in sixfold coordination gets narrower. Furthermore, the intensity of the NIR peak at 5500 cm⁻¹ increases. This is explained by the incorporation of iron in the respective glass structures.     

Viscosity of (GeSe2)x(Sb2Se3)1−x undercooled melts

Viscosity of (GeSe₂)_x(Sb₂Se₃)_1−x undercooled melts (x = 0.4-0.8) was measured using parallel-plate method and penetration method. By using these two techniques viscosity of the whole measurable region of undercooled melt and of the part of glass region can be measured. In this relatively broad viscosity interval (seven orders of magnitude) all measured samples show Newtonian behavior and the dependence of their viscosity on temperature can be described by a simple Arrhenius equation. The kinetic fragilities calculated from these dependencies show similar compositional dependence as heat capacity changes at glass transition measured by DSC.     

Thermodynamical miscibility in 0.8[xB2O3-(1 − x)P2O5]-0.2K2O glasses

The thermodynamical miscibility in 0.8[xB₂O₃-(1 − x)P₂O₅]-0.2K₂O glasses has been studied by measuring the glass transition temperature and the mixing enthalpy. Measurements have been performed by differential scanning calorimeter and hydrofluoric acid solution calorimetry at 298 K. The enthalpies of mixing are significantly negative over the whole range of composition. The results are discussed in terms of intermolecular associations.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

The effect of alumina on the Sn/Sn redox equilibrium and the incorporation of tin in Na2O/Al2O3/SiO2 melts

Glasses with the basic compositions 10Na₂O · 10CaO · xAl₂O₃ · (80 − x)SiO₂ (x=0, 5, 15, 25) and 16Na₂O · 10CaO · xAl₂O₃ · (74 − x)SiO₂ (x=0, 5, 10, 15, 20) doped with 0.25-0.5 mol% SnO₂ were studied using square-wave-voltammetry at temperatures in the range from 1000 to 1600 °C. The voltammograms exhibit a maximum which increases linearly with increasing temperature. With increasing alumina concentration and decreasing Na₂O concentration the peak potentials get more negative. Mössbauer spectra showed two signals attributed to Sn²⁺ and Sn⁴⁺. Increasing alumina concentrations did not affect the isomer shift of Sn²⁺; however, they led to increasing quadrupole splitting, while in the case of Sn⁴⁺ both isomer shift and quadrupole splitting increased. A structural model is proposed which explains the effect of the composition on both the peak potentials and the Mössbauer parameters.     

Crystallization and glass transition kinetics in Cu ion substituted Cux-Ag1 − xI-Ag2O-V2O5 superionic glasses

Crystallization kinetics and thermal properties in superionic glasses Cu_xAg_1 − xI-Ag₂O-V₂O₅ for x = 0.1-0.3 have been thoroughly investigated. X-ray diffraction and differential scanning calorimetry measurements confirm the precipitation of at least three compounds during crystallization, viz. AgI, Ag₄V₂O₇ and Ag₈I₄V₂O₇. The activation energies for structural relaxation (E_s) and crystallization (E_c) obtained using Moynihan and Kissinger formulation exhibit interesting trends with CuI substitution. The E_s value decreases with CuI substitution in the system. Further, the E_c values corresponding to precipitation of Ag₄V₂O₇ and Ag₈I₄V₂O₇ exhibit increasing trend, whereas, for that of AgI precipitation a decreasing trend with CuI content. The Avrami parameter calculated from Augis-Bennett method and Ozawa equation suggests predominantly surface crystallization in the glassy system. The electrical conductivity-temperature (σ-T) cycles interestingly demonstrate increasing precipitation of AgI with CuI content in the glass matrix.     

Bioactive glasses in the system CaO-B2O3-P2O5: Preparation, structural study and in vitro evaluation

Glasses in the system x B₂O₃(1 − x) [y CaO P₂O₅], (x = 0, 0.1, 0.2, 0.3, y = 2, 2.6, 3, 4, 5) have been prepared by fast quenching of high temperature melts. The presence of B₂O₃ affected the glass forming ability, allowing the preparation of calcium phosphate glasses with y ? 2.6. The structure of glasses was analyzed by μ-Raman and infrared spectroscopy. The analysis indicated that the glass network is dominated by highly charged species from phosphate tetrahedra with 3 (pyro) or 4 (ortho) NBOs, while the boron atoms are incorporated mainly in 3 coordinated sites in the form of B∅₃ or B∅₂O⁻ units. A small fraction of units was also evident from the spectra analysis of glasses with high CaO content. All calcium borophosphate glasses exhibited bioactivity after soaking in SBF solution within a few days. This was observed by μ-Raman and SEM microscopy, while XRD patterns clearly revealed growth of hydroxyapatite phase. The presence of boron in the glass network has a catalytic effect at favoring bioactivity of the otherwise bioinert calcium phosphate glasses.     

Optical properties of Cr ion in lithium metasilicate Li2O · SiO2 transparent glass-ceramics

The optical properties of Cr³⁺ ions in lithium metasilicate (Li₂O · SiO₂) transparent glass-ceramics were investigated. The main crystalline phase precipitated was the lithium metasilicate (Li₂O · SiO₂) crystal. The percent crystallinity and crystalline size were ranging 65-75% and 20-35 nm, respectively. The color changes drastically to deep pink from emerald green upon crystallization. New and strong absorption bands appeared and the absorption intensity increases by about 10 times that in glass. These new absorption bands are found to be derived from Cr³⁺ ions in octahedral sites in the lithium metasilicate crystal lattice. Cr³⁺ ions substitute for three Li⁺ ions and occupy the distorted octahedral site between single [SiO₄]_n chains of lithium metasilicate crystal. The ligand field parameters can be estimated: 10Dq = 13 088 cm⁻¹, B = 453 cm⁻¹, Dq/B = 2.89 and C = 2036 cm⁻¹. The near-infrared luminescence centered at 1250 nm was not detected in the deep pink glass-ceramics unlike emerald green glass.     

Thermodynamic mixing properties of liquids in the system Na2O-SiO2

Enthalpies of fusion have been measured by differential scanning calorimetry for a Na₂O-SiO₂ system at 50, 66.6, and 74.4 mol% SiO₂. Enthalpies of mixing of liquids obtained from different calorimetry techniques are critically evaluated. The data on calorimetric enthalpy, activity of Na₂O, cristobalite liquidus, and immiscibility gap are used to determine the enthalpy and entropy of mixing of sodium-silicate liquids are determined as a function of composition by the least squares method. The derived mixing properties are based only on the experimental data and are independent of any assumption about the structure and chemical species in liquids. The enthalpy of mixing has a minimum value of −120 kJ/mol at 35-40 mol% SiO₂ and is convex upward around 80-90 mol% SiO₂. The entropy of mixing have a maximum value of + 6 J/K-mol at 75 mol% SiO₂, and it decreases with the SiO₂ content to −5 J/K-mol at 40 mol% SiO₂. This decrease in entropy can be accounted for by ideal mixing of Q⁴, Q³, and Q^{0 + 1 + 2} (= Q⁰ + Q¹ + Q²) species in the liquids and is responsible for the negative temperature dependence of the partial molar Gibbs energy of mixing of Na₂O, observed in activity measurements. Comparison of the present results with previous values suggests that a quasi-chemical model and the Adam-Gibbs model overestimate the configurational entropy of mixing of liquids.     

Three-dimensional structure of fast ion conducting 0.5Li2S + 0.5[(1 − x)GeS2 + xGeO2] glasses from high-energy X-ray diffraction and reverse Monte Carlo simulations

A high-energy X-ray diffraction study has been carried out on a series of 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses with x = 0.0, 0.1, 0.2, 0.4, 0.6 and 0.8. Structure factors were measured to wave vectors as high as 30 Å⁻¹ resulting in atomic pair distribution functions with high real space resolution. The three dimensional atomic-scale structure of the glasses was modeled by reverse Monte Carlo simulations based on the diffraction data. Results from the simulations show that at the atomic-scale 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses may be viewed as an assembly of independent chains of (Li^+-S)₂GeS_2/2 and (Li^+-O)₂GeO_2/2 tetrahedra as repeat units, where the Li ions occupy the open space between the chains. The new structure data may help understand the reasons for the sharp maximum in the Li⁺ ion conductivity at x ∼ 0.2.     

Dielectric analysis of tungsten-phosphoniobate 20A2O-30WO3 -10Nb2O5 -40P2O5 (A = Li, Na) glass-ceramics

New phosphate glasses of the quaternary system A₂O-Nb₂O₅-WO₃-P₂O₅, where X = Li and Na were prepared by the melt-quenching method. The introduction of WO₃ in the glass composition was based on the proposal of analysing the effect of the diminishing of the molar amount of the alkaline oxide and thus decreasing the molar ratio between network modifiers and network formers (M/F).In the present work we present the preparation of 20A₂O-30WO₃-10Nb₂O₅-40P₂O₅ (A = Li, Na) transparent glasses. These glasses were heat-treated in air, at 550 °C and 650 °C for 4 h. The structure of the obtained samples was studied by X-ray powder diffraction (XRD) and Raman spectroscopy and the morphology by scanning electron microscopy (SEM). The dc (σ_dc), ac (σ_ac) conductivity and dielectric spectroscopy measurements were performed in the function of the temperature and were related with the structural changes of the glass structures.     

Electrical properties of AsxSe1−x (x ≤ 0.05) Mott-barriers

We have experimentally measured the current-voltage and capacitance-voltage characteristics of Au/amorphous As_xSe_1 − x (x ≤ 0.05)/Zr trilayer structures at temperatures from 4 to 295 K. The observed capacitance of structures with an amorphous As_xSe_1 − x (a-As_xSe_1 − x) thickness of ~ 0.4 to ~ 2.8 μm does not significantly change over the entire range of applied bias (− 5 V to 5 V), indicating that the a-As_xSe_1 − x films are fully depleted and thus the structures are Mott barriers. The current-voltage (I-V) characteristics of the a-As_0.03Se_0.97 device at low (< 3000 V/cm) to moderate fields (3000 V/cm-10000 V/cm) follow the predictions of trap limited space charge conduction theory, as they exhibit Ohmic behavior at low fields and trap limited space charge current at moderate fields. According to the trap limited space charge current model of Lampert, the a-As_0.03Se_0.97 film has an effective hole mobility, Θμ (with Θ < 1), of ~ 5 × 10^− 7 cm²/V-sec at 295 K. This value is similar to, but consistently lower than previously reported mobilities inferred from time of flight measurements. The current at high fields (> 10⁴ V/cm) increases rapidly with applied field as a result of carrier emission from localized states and is consistent with transport by the Poole-Frenkel mechanism. A permanent transition to a high conductance state (~ 10^− 3 S) is observed after exposure to very high electric fields (~ 4 × 10⁵V/cm).     

Spectrometric and ellipsometric studies of (1 − x)TiO2 · xLn2O3 (Ln = Nd, Sm, Gd, Er, Yb) thin films

Spectrometric and ellipsometric studies of (1 − x)TiO₂ · xLn₂O₃ (Ln = Nd, Sm, Gd, Er, Yb; x = 0.33, 0.5) thin films at room temperature were performed. The obtained dispersion dependences of refractive indices are successfully described by the optical-refractometric relation. The dependence of optical pseudogap and refractive indices on composition and molar mass of the films is investigated. The influence of compositional disordering on the energy width of the exponential absorption edge is studied.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.