AC impedance analysis of CsNO3:Al2O3 composite solid electrolyte systems

Complex impedance spectroscopic studies were carried out on CsNO₃ and CsNO₃-Al₂O₃ dispersed solid electrolyte systems (DSES) in the temperature range of 100-350 °C and the frequency 50 kHz-1 MHz. Dielectric constant, loss tangent, ac conductivity and dc ionic conductivity (obtained from CIS) in these systems are presented. DC ionic conductivity is noticed to increase with temperature in the extrinsic region in pure and dispersed systems. The enhancement of conductivity in DSES was observed to be about two orders of magnitude over its pure form in the extrinsic region. This enhancement of conductivity was attributed to the formation of space charge layer between the host material and the dispersoid. Enhancement in conductivity is found to increase with m/o up to 40 m/o where as it decreased for 80 m/o. Dielectric constant, dielectric loss and ac conductivity are also found to increase with temperature, and with mole percent it maintained the similar behavior as that of dc conductivity. These dielectric properties are interpreted in terms of space charge polarization and increased concentration of defects in the interfacial layer formed between the host and the dispersoid.     

Electronic relaxation in zinc iron phosphate glasses

The electrical and dielectric properties of 10ZnO-30Fe₂O₃-60P₂O₅ (mol%) glasses, melted at different temperatures were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 3 MHz and over the temperature range from 303 to 473 K. It was shown that the dc conductivity strongly depends on the Fe(II)/[Fe(II) + Fe(III)] ratio. With increasing Fe(II) ion content from 17% to 37% in these glasses, the dc conductivity increases. Procedure of scaling conductivity data measured at various temperatures into a single master curve is given. The conductivity of the present glasses is made of conduction and conduction-related polarization of the polaron hopping between Fe(II) and Fe(III), both governed by the same relaxation time, τ. The high frequency dispersion in electrical conductivity arises from the distribution in τ caused by the disordered glass structure. The evolution of the complex permittivity as a function of frequency and temperature was investigated. At low frequency the dispersion was investigated in terms of dielectric loss. The thermal activated relaxation mechanism dominates the observed relaxation behavior. The relationship between relaxation parameters and electrical conductivity indicates the electronic conductivity controlled by polaron hopping between iron ions.     

Ac conductivity and dielectric relaxation in ionically conducting soda-lime-silicate glasses

The frequency dependent conductivity and dielectric relaxation of alkali ions in some soda-lime-silicate (Na₂O-CaO-SiO₂) glasses are investigated over a frequency range from 50 Hz to 1 MHz and in a temperature range from room temperature to 603 K by using alternating current impedance spectroscopy. The conductivity isotherms show a transition from frequency independent dc region to dispersive region where the conductivity continuously increases with increasing frequency. The electric modulus representation has been used to provide comparative analysis of the ion transport properties in these glasses. The scaling behavior of imaginary part of electric modulus indicates that all dynamical processes occurring at different frequencies give the same activation energy.     

Debye type dielectric relaxation in carbon nano-balls’ and 4-DMAABCA acid doped E7 coded nematic liquid crystal

The electrical properties of carbon nano-balls’ and 4-dimethylaminoazobenzene-2′-carboxylic acid doped dispersed nematic liquid crystal composite were investigated by impedance spectroscopy technique. The conductivity and capacitance were measured in the frequency range 100 kHz-1 MHz and temperature range 300-380 K. The loss peak was observed in the dielectric loss spectra and was identified as nearly-Debye type relaxation. Cole-Cole plots have been used to describe the characteristic changes of electrical properties in mentioned temperature interval. The sample presents monodispersive relaxation behavior with a relaxation time of ∼10⁻⁷ s. The relaxation process is attributed to the dipolar rotation of the long molecular axis and the activation energy is found to be 0.097 eV.     

Preparation and the proton conductivity of chitosan/poly(vinyl phosphonic acid) complex polymer electrolytes

This study describes the preparation and proton conductivity of novel polymer complex electrolytes consisting of chitosan and poly(vinylphosphonic acid), PVPA. The materials were prepared via in situ polymerization of vinyl phosphonic acid in the presence of chitosan at various monomer feed ratios with respect to d-glucosamine repeat unit. Homogeneous materials were produced and they were extensively characterized for their compositions by elemental analysis (EA), thermal properties by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) and the morphology by X-ray diffraction (XRD). The complexation of chitosan/PVPA via proton exchange reactions was confirmed by Fourier transform infrared (FT-IR). The methanol permeability of CHPVPA₅ was lower than Nafion^® 115. The water/methanol uptake was measured and the results showed that solvent absorption of the materials increased with increasing PVPA content in the matrix. The temperature dependence of the proton conductivity of the complex electrolytes follows VTF behavior at higher x. Proton conductivity of CHPVPA₅ was measured to be approximately 3 × 10⁻⁵ S/cm at 120 °C in the anhydrous state.     

Preparation and characterization of p-type hydrogenated amorphous silicon oxide film and its application to solar cell

Thin film wide band gap p-type hydrogenated amorphous silicon (a-Si) oxide (p-a-SiOx:H) materials were prepared at 175 °C substrate temperature in a radio frequency plasma enhanced chemical vapor deposition (RF-PECVD) and applied to the window layer of a-Si solar cell. We used nitrous oxide (N₂O), hydrogen (H₂), silane (SiH₄), and diborane (B₂H₆) as source gases. Optical band gap of the 1% diborane doped films is in the range of 1.71 eV to 2.0 eV for films with increased oxygen content. Dark conductivity of these films is in the range of 8.7 × 10^− 5 S/cm to 5.1 × 10^− 7 S/cm. The fall in conductivity, that is nearly two orders of magnitude, for about 0.3 eV increase in the optical gap can be understood with the help of Arrhenius relation of conductivity and activation energy, and may not be significantly dependant on defects associated to oxygen incorporation. Defect density, estimated from spectroscopic ellipsometry data, is found to decrease for samples with higher oxygen content and wider optical gap. Few of these p-type samples were used to fabricate p-i-n type solar cells. Measured photo voltaic parameters of one of the cells are as follows, open circuit voltage (V_oc) = 800 mV, short circuit current density (J_sc) = 16.3 mA/cm², fill-factor (FF) = 72%, and photovoltaic conversion efficiency (η) = 9.4%, which may be due to improved band gap matching between p-a-SiOx:H and intrinsic layer. J_sc, FF and V_oc of the cell can further be improved at optimized cell structure and with intrinsic layer having a lower number of defects.     

Dielectric study and ac conductivity of iron sodium silicate glasses

A series of glasses with formula (SiO₂)_0.7−x(Na₂O)_0.3(Fe₂O₃)_x with ( 0.0 ≤ x ≤ 0.20) were prepared and studied by means of AC measurements in the frequency range 20 kHz to 13 MHz at room temperature. The study of frequency dependence of both dielectric constant ε' and dielectric loss ε" showed a decrease of both quantities with increasing frequency. The results have been explained on the basis of frequency assistance of electron hopping besides electron polarization. From the Cole-Cole diagram the values of the static dielectric constant ε_s, infinity dielectric constant ε_∞, macroscopic time constant τ, and molecular time constant τ_m are calculated for the studied amorphous samples. The frequency dependence of the ac conductivity obeys a power relation, that is σ_ac (ω) = Α ω^s. The obtained values of the constant s lie in the range of 0.7 ≤ s ≤ 1 in agreement with the theoretical value which confirms the simple quantum mechanical tunneling (QMT) model. The increase in ac conductivity with iron concentration is likely to arise due to structural changes occurring in the glass network. The structure of a glass with similar composition was published and showed clustering of Fe²⁺ and Fe³⁺ ions which favor electron hopping and provide pathways for charge transport.     

A novel route of synthesis of WS2 thin film and its characterization

WS₂ thin films have been deposited by chemical deposition technique using citric acid as a complexing agent at 343 K. X-ray pattern shows that crystalline nature with hexagonal- and orthorhombic-mixed phase. The films show that good optical properties high absorption and band gap value was found to be 1.31 eV. The specific conductivity of the film was found to be in order of 10⁻³ (Ω cm)⁻¹.     

Transport property and structural characterization studies on (1 − x)[0.75AgI:0.25AgCl]:xTiO2 conducting composite electrolyte system

Transport property and structural investigation have been carried out on newly synthesized Ag⁺ ion conducting composite electrolyte system. The composite electrolyte system (1 − x)[0.75AgI:0.25AgCl]:xTiO₂, where 0 ? x ? 0.5 (in molar weight fraction) has been synthesized by melt quenching and annealing methods. The chemical compound TiO₂ (second phase dispersoid) dispersed in different compositions in a quenched (0.75AgI:0.25AgCl) mixed system/solid solution; this solid solution was used as a first phase host salt in place of AgI. The different preparation routes were adopted for the composite electrolyte system. Composition x = 0.1 exhibited highest conductivity at room temperature. The composite system 0.9[0.75AgI:0.25AgCl]:0.1TiO₂ was synthesized at different soaking times by melt quenching method. The system exhibited optimum conductivity at 20 min soaking time (σ_rt ≈ 1.4 × 10⁻³ S/cm). The ac conductivity has been measured from Z′-Z″ (Cole-Cole) complex impedance plots using impedance spectroscopic (IS) technique. The electrical conductivity as a function of temperature and frequency has been studied, and activation energy E_a, was calculated from Arrhenius plots for all compositions (0 ? x ? 0.5). The dc conductivity value has been evaluated from Log σ vs. log f plots. Structural characterization studies were carried out by X-ray diffraction (XRD) and differential thermal analysis (DSC) techniques.     

Spectroscopic and dielectric properties of a lithia-containing glass

Glass of the composition 65SiO₂-20CaO-15Li₂O (mol %) was prepared and subjected to heat treatment. The obtained samples were characterized before and after heat treatment by DTA, TG, XRD, SEM, IR and dielectric spectroscopy. DTA showed an endothermic peak at 954 °C, accompanied by a pronounced change in the microstructure, as revealed by SEM. XRD showed that metasilicate predominates on heat treatment at 726 °C, while on heat treatment at 726 °C, then at 954 °C, disilicate crystallizes as the main phase. The IR spectra of the heat-treated glasses revealed that the vibrations of O-H groups are drastically decreased, while those due to non-bridging oxygens Si-O⁻ are increased. The dielectric constant (ε′), the loss tangent (tan δ) and the ac conductivity (σ_ac) for the prepared glasses were investigated before and after heat treatment over a moderately wide range of frequency and temperature. The activation energy of the dielectric relaxation process was found to depend on the techniques of sample preparation. A drop of dielectric constant values was observed for the heat-treated sample, which can be attributed to the ordering of the induced crystalline phases. The conductivity behavior suggests a hopping mechanism responsible for conduction.     

Studies on electrical and the dielectric properties in MS structures

In this study, we investigated frequency dependent electrical and dielectric properties of metal-semiconductor (MS) structures using capacitance-voltage (C-V) and conductance-voltage (G/ω-V) characteristics in the frequency range 100 kHz-10 MHz in the room temperature. The dielectric constant (ε′), dielectric loss (ε″), dielectric loss tangent (tan δ) and ac electrical conductivity (σ_ac) were calculated from the C-V and G/ω-V measurements and plotted as a function of frequency. In general, ε′, ε″ and tan δ values decreased with increasing the frequency, while σ_ac increased with increasing frequency. Furthermore, the voltage and frequency dependence of series resistance were calculated from the C-V and G/ω-V measurements and plotted as functions of voltage and frequency. The distribution profile of R_S-V gives a peak in the depletion region at low frequencies and disappears with increasing frequencies. Also, series resistance values decreased with increasing frequency. The experimental results show that both frequency dependent electrical and dielectric parameters were strongly frequency and voltage dependent.     

Investigation on dielectric relaxations of PVP-NH4SCN polymer electrolyte

Poly (N-vinyl pyrrolidone) (PVP) and ammonium thiocyanate (NH₄SCN) based polymer films with different compositions have been prepared by solution casting technique. The amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The FTIR analysis confirms the complex formation of the polymer with the salt. The conductivity analysis shows that the 20 mol% ammonium thiocyanate doped polymer electrolyte has high ionic conductivity and it has been found to be 1.7 × 10⁻⁴ S cm⁻¹, at room temperature. From the admittance plot, the activation energy has been found to be low for 20 mol% salt doped polymer electrolyte. The dielectric behavior has been analyzed using dielectric permittivity (ε^∗), dissipation factor (tan δ) and electric modulus (M^∗) of the samples.     

Structural, thermal and electrical properties of PVA-LiCF3SO3 polymer electrolyte

The development of polymeric systems with high ionic conductivity is one of the main objectives in Li rechargeable battery. In the present study, the different composition of PVA-LiCF₃SO₃ polymer electrolyte has been prepared by solution cast technique using DMSO as solvent. The FTIR study confirms the polymer-salt complex formation. The amorphous nature of the polymer has been confirmed by XRD analysis. DSC measurements show decrease in T_g with increasing salt concentration. The temperature dependent conductivity obeys Arrhenius relationship. The maximum conductivity has been observed in the order of 7 × 10^− 4 S cm^− 1 for 25 mol% of LiCF₃SO₃. The activation energy has been found to be 0.16 eV. The two peaks have been observed in the dielectric loss spectrum which shows two types of relaxation α and β.     

Growth and characterization of glycine picrate—Remarkable second-harmonic generation in centrosymmetric crystal

Remarkable second-harmonic generation (SHG) efficiency has been observed in the glycine picrate (GP) though it crystallizes in centrosymmetric structure. Bulk single crystals of GP with a good size of ~20×10×3 mm³ have been successfully grown by the slow cooling method in aqueous medium. Powder X-ray diffraction (PXRD), Fourier transform infrared (FT-IR) and FT-Raman studies have confirmed, respectively, the crystal structure and functional groups of the grown crystal. Crystalline perfection of single crystals has been evaluated by high-resolution X-ray diffractometry (HRXRD) using a multicrystal X-ray diffractometer and found that the grown crystals are nearly perfect. Nonlinear optical (NLO) behavior of glycine picrate crystals has been studied for the first time by Kurtz powder technique and its second-harmonic generation efficiency is found to be 2.34 times higher than that of KDP. Transparency of crystals in UV–vis–NIR region has also been studied. Dielectric measurements have been carried out using an impedance analyzer over a wide range of frequency (100 Hz–3 MHz) at room temperature. The slight decrease in dielectric constant has been observed as the frequency is increased and the dielectric loss is very low for the entire frequency range. The ac conductivity is almost constant up to 1 MHz and sudden increase has been observed above this frequency.     

Decrease in dielectric loss of CaCu3Ti4O12 by the addition of TeO2

CaCu₃Ti₄O₁₂ (CCTO) has challenged for the last few years the scientific community due to its large dielectric constant, which is almost temperature and frequency independent, from 100 K to 400 K and from 1 kHz to 1 MHz, respectively. This makes the material desirable for many electronic applications. However, the dissipation factor is very large, with tan δ values, at room temperature and 1 kHz, higher than 0.1.In our work we report how the addition of TeO₂ lowers the dielectric loss and, although there is a decrease of dielectric constant of doped samples relatively to the undoped one, high dielectric constant values are still being reached. The sample of doped CCTO with 1.5% of TeO₂ by weight, presents, at room temperature and 60 kHz, a large dielectric constant, over 3000, and a dissipation factor around 0.09, which represents a decrease on tan δ over 30% relatively to the CCTO undoped sample. Two relaxation processes were identified for all the samples, one at MHz region and the other one at low frequency region (< 1 kHz). DC bias voltage was applied up to 40 V and a strong dc bias influence on the low frequency region was observed both at dielectric and impedance responses of the undoped sample, which was much weaker than the dc bias effects on the 4% Te doped sample.Dielectric measurements will be discussed and correlated with the samples' microstructure, supported on internal barrier layer capacitance (IBLC) and surface barrier layer capacitance (SBLC) models.     

Investigation of near constant loss contribution to conductivity in lithium bismo-silicate glasses

Glasses having compositions 20Li₂O · (80 − x)Bi₂O₃ · xSiO₂ (x = 55, 60, 65, 70 mol%) were investigated using impedance spectroscopy in the frequency range from 20 Hz to 1 MHz and in the temperature range from 543 to 663 K. The ac and dc conductivities, activation energy of the dc conductivity and relaxation frequency are extracted from the impedance spectra. The increase in conductivity with increase in SiO₂ content is attributed to the change in the structural units of bismuth. Both electric modulus and the conductivity formalism have been employed to study the relaxation dynamics of charge carriers in these glasses. A single ‘master curve’ for normalized plots of all the modulus isotherms observed for a given composition indicates the temperature independence of the dynamic processes for ions in these glasses. Similar values of activation energy for dc conduction and for conductivity relaxation time indicates that the ions overcome same energy barrier while conducting and relaxing. The observed conductivity spectra follows power law with exponent ‘s’ which increases regularly with frequency and approaches unity at higher frequencies. Near constant losses (NCL) characterize this linearly dependent region of conductivity spectra. A deviation from ‘super curve’ for various isotherms of conductivity spectra was also observed in high frequency region and at low temperatures, which supports the existence of different dynamic processes like NCL in addition to the ion hopping processes in the investigated glass system.     

Ion conducting corn starch biopolymer electrolytes doped with ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate

Biodegradable corn starch-lithium hexafluorophosphate (LiPF₆) based biopolymer electrolytes were prepared by solution casting technique. Ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF₆) was doped into the polymer matrix. Upon addition of 50 wt.% BmImPF₆, the maximum ionic conductivity of (1.47 ± 0.02) × 10^− 4 Scm^− 1 was achieved due to its higher amorphous region. This result had been further proven in ATR-FTIR study. Frequency dependence of conductivity and dielectric studies reveal the occurrence of polarization at the electrolyte-electrode interface and thus form the electrical double layer, asserting the non-Debye characteristic of polymer electrolytes. This result is in good agreement with dielectric loss tangent study. Based on the changes in shift, changes in intensity, changes in shape and existence of some new peaks, attenuated total reflectance-Fourier Transform Infrared (ATR-FTIR) divulged the complexation between corn starch, LiPF₆ and BmImPF₆, as shown in the spectra.     

The dielectric behavior of a thermoelectric treated B2O3-Li2O-Nb2O5 glass

A transparent glass with the composition 60B₂O₃-30Li₂O-10Nb₂O₅ (mol%) was prepared by the melt-quenching technique. Glass-ceramics, containing LiNbO₃ ferroelectric crystallites, were obtained by heat-treatment (HT) above 500 °C, with and without the presence of an external electric field. The dielectric properties of the glass and glass-ceramic were investigated, as a function of temperature (270-315 K), in the 10 mHz-32 MHz frequency range. The presence of an external electric field, during the heating process, improves the formation of LiNbO₃ crystallites. The rise of the treatment temperature and the applied field, during the heat-treatment, leads to a decrease in the dc electric conductivity (σ_dc), indicating a decrease of the charge carriers number. The dielectric permittivity (ε′) values (300 K;1 kHz) are between 16.25 and 18.83, with the exception of the 550 °C HT sample that presents a ε′ value of 11.25. An electric equivalent circuit composed by an R in parallel with a CPE element was used to adjust the dielectric data. The results reflect the important role carried out by the heat-treatment and the electric field during the HT in the electric properties of glass-ceramics.     

Complexation of macrocyclic ligands in ionic SDS micellar solutions: A dielectric spectroscopy investigation

The influence of two different macrocyclic ligands, [2.2.2] cryptand (C222) and 18-crown-6 (18C6) ether on the structural properties of sodium dodecyl sulfate (SDS) micellar solutions has been investigated by means of dielectric spectroscopy, in a frequency range from 1 kHz to 50 GHz. The dielectric spectra of SDS micellar solutions present three relaxation processes. In the MHz region, two different relaxations centered at about 30 MHz and 300 MHz, can be attributed to the micelle contribution, while, close to 20 GHz, the contribution of the bulk water orientational polarization is observed. The addition of ligands causes relevant changes in the overall dielectric relaxation spectrum. Significantly, the relaxation processes corresponding to the micelle component are largely modified by the presence of the different ligands investigated both in the relaxation frequency and in the dielectric strength, thus indicating a reorganization of the charged interface of ligand-decorated micelles. These changes are briefly discussed in the light of the phenomenology observed in attractive colloids, where the presence of a long-range electrostatic repulsive interaction and a short-range attractive interactions results in the presence of a well-defined cluster phase.     

Development of optical nonlinearity, high dielectric constant and ferromagnetic behavior in a silicate glass nanocomposite by suitable heat treatment

We have explored the development of multifunctionalities viz, optical nonlinearity, high dielectric constant and ferromagnetic behavior in a nanostructured silica based glass of 14.0Na₂O, 26.0BaO, 26.0TiO₂, 16.0B₂O₃, 17.0SiO₂, 1.0NiO (mol%) composition. A heat treatment at 863 K for 4 h led to nonlinear refractive index and absorption coefficients at wavelength 800 nm of 0.11 × 10⁻¹⁹ m²/W and 1.15 × 10⁻³ cm/GW, respectively. A heat treatment at 1073 K for 2 h followed by 1113 K for 3 h increased the dielectric constant from 11 to 50, apparently due to the formation of nanocrystals of BaTiO₃ within the glass medium. Glass samples reduced at 923 K for 1 h exhibited ferromagnetic behavior due to the presence of nickel nanoparticles.