Mechanical properties of a TAS fiber: a preliminary study

The mechanical properties, including elastic moduli, hardness, fracture toughness and tensile strength of a glass fiber in the Te-As-Se system (TAS) were studied. The values for the hardness (1.4 GPa) and the fracture toughness (0.18 MPa √m) show that this glass is both soft and brittle in comparison to glasses from other systems. However, indentation measurements should be interpreted with caution due to an indentation creep phenomenon and to a delayed fracture process. In addition, the effect of treatments in air (relative humidity about 60%) at different temperatures below T_g were investigated. The main result of this study is that the studied TAS glass is sensitive to the presence of humidity, and aging treatments have a pronounced detrimental effect on the strength of the uncoated fibers.     

Zr-based bulk metallic glass with super-plasticity under uniaxial compression at room temperature

Commonly, bulk metallic glasses exhibit very limited plastic deformation (<2%) at room temperature. In this letter, through appropriate composition choices, rods of Zr_62.55Cu_17.55Ni_9.9Al₁₀ and Zr_64.80Cu_14.85Ni_10.35Al₁₀ bulk metallic glasses (BMGs) were prepared by using copper-mold suction-casting. X-ray diffraction and differential scanning calorimetry were utilized to determine their structures and thermal stabilities, and uniaxial compression tests were adopted to study their plastic deformation behaviors (PDBs) at room temperature. The results showed that T_g and T_x of the former are 651.5 K and 748 K, respectively, while those of the latter are 646 K and 750 K, respectively. Micro-hardness values are 693 ± 7 Hv and 595 ± 5 Hv for T1 and T2, respectively. During the compression tests, the former underwent about 2.5% engineering strain, i.e., 2.8% true strain, then fractured. While the latter was compressed into a flake-like form, of which, engineering strain values are larger than 70%, i.e., true strain exceeds 120%, showing super-plasticity at room temperature. It can be concluded that micro-hardness and PDBs of BMGs are very sensitive to composition.     

Hf–Cu–Ni–Al bulk metallic glasses: Optimization of glass-forming ability and plasticity

In the Hf–Cu–Ni–Al quaternary system, the Hf₅₁Cu_27.75Ni_9.25Al₁₂ bulk metallic glass (BMG) exhibits the best combination of the large glass-forming ability (GFA) and compressive plasticity. Minor substitution of Nb for Hf in Hf–Cu–Ni–Al BMGs degrades not only the GFA but also plasticity, while the substitution of Ta does not have an appreciable effect on both properties. For the investigated Hf-based BMGs, the shear modulus G is a more sensitive indicator to correlate with their plasticity than the Poisson′s ratio. Meanwhile, the correlation between the G and the glass transition temperature T_g for the Hf-based BMGs can be expressed as G = 9.9 + 576 (T_g/V_m)[1 ? 4/9(T/T_g)^2/3].     

Elasticity, thermal expansion and compressive behavior of Mg65Cu25Tb10 bulk metallic glass

The existence of special covalently bonded short-range ordering structures in a Mg₆₅Cu₂₅Tb₁₀ bulk metallic glass (BMG) is confirmed by thermal expansion and compression behavior. Under ambient conditions the linear thermal expansion coefficient obtained is almost constant in the glassy state with a value of 4.0 × 10⁻⁵ K⁻¹. By fitting the static equation of state at room temperature under ambient conditions we find the value for bulk modulus B of 48.7 GPa, which is in excellent agreement with the experimental study by pulse-echo techniques of 44.7 GPa. Unlike many bulk metallic glasses, such as Zr- and Pd-based, which bulk modulus is much larger than 100 GPa, the value B of Mg₆₅Cu₂₅Tb₁₀ BMG falls into the range of SiO₂ and fluorozirconate glass ZBLAN. Moreover, the elastic constant of the Mg₆₅Cu₂₅Tb₁₀ BMG is almost the same as those of ZBLAN. No evidence for the high-pressure phase transitions of the Mg₆₅Cu₂₅Tb₁₀ BMG has been found up to 31.19 GPa at room temperature.     

Crystallization behavior of Zr41Ti14Cu12.5Ni10Be22.5 bulk metallic glass under the action of high-density pulsing current

The crystallization behavior of Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (Vit1 BMG) under the action of high-density pulsing current (HDPC) have been studied experimentally. It has been found that high-density pulsing current can directly induce the rapid nanocrystallization of Vit1 BMG. The multiple crystallization processes of Vit1 BMG induced by HDPC have been confirmed as Amorphous → Amorphous + i-phase → Be₂Zr + Zr₂Cu + Ni₇Zr₂ + FCC phase + other phases → Zr₂Cu + Ni₇Zr₂ + FCC phase + other phases. By comparing to the crystallization behavior of Vit1 BMG induced by isothermal annealing, the crystallization temperature is reduced and crystallizing process is significantly shortened, while the sequence of crystallization process in both cases is basically same. The present results show that the HDPC has significantly influenced the crystallizing kinetics of Vit1 BMG due to that it can greatly promote the movement and rearrangement of atoms, which will result in a rapid nanocrystallization. It suggests that HDPC treatment can be an effective way to induce the rapid nanocrystallization of BMGs.     

Effect of Ti addition on the crystallization behavior and glass-forming ability of Zr-Al-Cu alloys

The crystallization behavior of melt-spun (Zr₆₅Al_7.5Cu_27.5)_100−xTi_x (x = 0-15; in at.%) metallic glasses has been investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The DSC traces showed an altered crystallization mode in the vicinity of 3 at.% Ti addition. A metastable icosahedral quasicrystal precipitated at the first crystallization stage of the Ti-bearing metallic glasses, which subsequently transformed to the stable Zr₂Cu-type phase in the followed exothermic reaction. The glass-forming abilities (GFAs) of these metallic glasses were assessed by the recognized GFA indicators T_rg, ΔT_x and γ. BMGs were easily made in the compositions containing 3-7 at.% Ti by means of copper mold casting. The validity of these parameters was clarified using the critical BMG forming diameter evidence.     

Thermal stability of amorphous Mg50Ni50 alloy produced by mechanical alloying

Amorphous Mg₅₀Ni₅₀ alloy was produced by mechanical alloying (MA) of the elemental powders Mg and Ni using a SPEX 8000D mill. The alloyed powders were microstructurally characterized by X-ray diffraction (XRD). The thermal transformation of amorphous Mg₅₀Ni₅₀ into stable intermetallics (Mg₅₀Ni₅₀ → remaining amorphous + Mg₂Ni → Mg₂Ni + MgNi₂) was analyzed using the Kissinger and isoconversional methods based on the non-isothermal differential scanning calorimetry (DSC) experiments. The apparent activation energies (E_a) and the transformation diagrams, temperature-time-transformation (T-T-T) and temperature-heating rate-transformation (T-HR-T), were obtained for both processes. A good agreement was observed between the calculated transformation curves and the experimental data, which verifies the reliability of the method utilized.     

Bulk metallic glass formation in Cu–Zr–Ti ternary system

The formation of bulk metallic glasses (BMG) in the Cu-rich Cu–Zr–Ti ternary system is studied by using the ‘e/a-variant line criterion’. Three such lines, (Cu₉Zr₄)_1−xTi_x, (Cu_61.8Zr_38.2)_1−xTi_x and (Cu₅₆Zr₄₄)_1−xTi_x, are defined in the Cu–Zr–Ti system by linking three binary compositions Cu₉Zr₄, Cu_61.8Zr_38.2 and Cu₅₆Zr₄₄ to the third element Ti. The binary compositions Cu₉Zr₄, Cu_61.8Zr_38.2 and Cu₅₆Zr₄₄ correspond to specific Cu–Zr binary clusters. BMGs are obtained by copper mould suction casting method with Ti contents of 7.5–15 at.%, 7.5–12.5 at.% and 5–12 at.%, respectively along the (Cu₉Zr₄)_1−x Ti_x, (Cu_61.8Zr_38.2)_1−xTi_x and (Cu₅₆Zr₄₄)_1−xTi_x lines. The BMGs on each composition line manifest decreased thermal stabilities and glass forming abilities (GFAs) with increasing Ti contents. The maximum GFA appears at Cu₆₄Zr_28.5Ti_7.5, with characteristic thermal parameters of T_g = 736 K, T_x = 769 K, T_g/T_l = 0.627 and γ = 0.403, which are all superior to those reported for the known Cu₆₀Zr₃₀Ti₁₀ BMG.     

Glass formation ability and mechanical properties of Ti40Cu40Zr10Ni10 alloy

Melt-spun ribbon and bulk samples in cylindrical rod form with diameter ranging from 2 mm to 4 mm of Ti₄₀Cu₄₀Zr₁₀Ni₁₀ alloy were prepared by melt-spinning technique and copper mould casting method, respectively. The microstructure, thermal stability and mechanical properties of the bulk samples were investigated. A completely glassy single phase is formed in the 2 mm rod sample. Increasing the diameter of the rod samples resulted in the formation of CuTi crystalline phase in the 3 mm and 4 mm rod samples. The 2 mm single glassy rod sample exhibited a large supercooled liquid region ΔT_x = 58 K and γ = T_x/(T_g + T_l) is 0.390, which indicated that the alloy possessed a good glass-forming ability. The bulk samples also exhibited good mechanical properties. The 2 mm rod sample showed the highest yield strength of about 2086 MPa. The 3 mm rod sample not only showed high yield strength of about 2000 MPa, but also enhanced plastic strain of about 0.71%.     

Effect of microalloying of Nb on corrosion resistance and thermal stability of ZrCu-based bulk metallic glasses

Bulk metallic glasses (BMGs) of Zr_46−xNb_xCu_37.6Ag_8.4Al₈ with x = 0, 0.5, 1, 2 and 4 at.% were prepared by copper mould casting. The corrosion resistance of the ZrCu-based BMGs with different Nb contents was carefully examined by weight loss measurements and potentiodynamic polarization tests in 3 mass% NaCl, 1 N HCl and 1 N H₂SO₄ solutions, respectively. Nb addition improves the newly developed BMGs’ corrosion resistance in chloride-containing solutions and the alloys all exhibit excellent corrosion resistance in 1 N H₂SO₄. The corrosion behavior of the alloy containing 0 and 4 at.% Nb in phosphate-buffered solution was examined by electrochemical polarization tests. The influence of Nb addition on glass forming ability (GFA), thermal stability and mechanical property was investigated by X-ray diffraction, differential scanning calorimetry and compression tests, respectively. It is found that the addition of Nb can deteriorate the GFA and thermal stability of the base system, but little effect is observed on the mechanical properties, e.g., yielding strength and plasticity, of the ZrCu-based BMG alloys.     

Effects of Zn on the glass forming ability and mechanical properties of MgLi-based bulk metallic glasses

Through the addition of Zn element, Mg-Li-Cu-Zn-(Y, Gd) bulk metallic glasses (BMGs) with diameter of 2 mm have been successfully fabricated by conventional copper mold injection casting method. The X-ray diffractometer (XRD) patterns and differential scanning calorimeter (DSC) traces demonstrated that the as-cast Mg₆₀Li₅Cu₂₀Zn₅(Y, Gd)₁₀ BMGs were fully amorphous phase. By the minor addition of 5 at.% Zn, the supercooled liquid regions (SLR) of Mg₆₀Li₅Cu₂₀Zn₅(Y, Gd)₁₀ BMGs increased 6 K and 3 K respectively compared with that of Zn-free samples, which implied that their glass forming ability (GFA) and thermal stability were improved. It was also proved that the addition of Zn effectively enhanced the alloys’ fracture strength (453 MPa and 456 MPa) and elastic strain (0.75% and 0.92%), which were much higher than that of Mg₆₀Li₅Cu₂₅Y₁₀ BMG (403 MPa, 0.62%) and Mg₆₀Li₅Cu₂₅Gd₁₀ BMG (412 MPa, 0.82%).     

Structure and properties of Ni60(Nb100−xTax)34Sn6 bulk metallic glass alloys

Refractory bulk metallic glasses and bulk metallic glass composites are formed in quaternary Ni-Nb-Ta-Sn alloy system. Alloys of composition Ni₆₀(Nb_100−xTa_x)₃₄Sn₆ (x = 20, 40, 60, 80) alloys were prepared by injection-casting the molten alloys into copper molds. Glassy alloys are formed in the thickness of half mm strips. With thicker strips (e.g., 1 mm), Nb₂O₅ and Ni₃Sn phases and the amorphous phase form an in situ composite. Glass transition temperatures, crystallization temperatures, and ΔT_x, defined as T_x1 − T_g (T_x1: first crystallization temperature, T_g: glass transition temperature) of the alloys increase dramatically with increasing Ta contents. These refractory bulk amorphous alloys exhibit high Young’s modulus (155-170 GPa), shear modulus (56-63 GPa), and estimated yield strength (3-3.6 GPa).     

Glass formation and crystallization behavior in Mg65Cu25Y10−xGdx (x=0, 5 and 10) alloys

The glass forming ability and crystallization behavior of Mg₆₅Cu₂₅Y_10−xGd_x (x=0, 5 and 10) alloys have been investigated. The glass forming ability (GFA) is significantly improved when Y in Mg₆₅Cu₂₅Y₁₀ is substituted with Gd. Ternary Mg₆₅Cu₂₅Gd₁₀ bulk metallic glass (BMG) with diameter of at least 8 mm was successfully fabricated by conventional Cu-mold casting method in air atmosphere. Mg₂(Y, Gd) is the first competing crystalline phase against the glass formation in the Mg₆₅Cu₂₅Y_10−xGd_x (x=0, 5) alloys, while Mg₂Cu and Cu₂Gd are the competing crystalline phases in the Mg₆₅Cu₂₅Gd₁₀ alloy. Therefore, the suppression of the formation of Mg₂(Y, Gd) during cooling from the liquid improves the GFA significantly.     

Structural relaxation of Ti40Zr25Ni8Cu9Be18 bulk metallic glass

Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈ bulk metallic glass has a unique quenched-in nuclei/amorphous matrix structure. The crystallization of quenched-in nuclei, when the experimental isothermal annealing time is within its incubation time, may not disturb the enthalpy relaxation, which makes it have the accordingly common enthalpy relaxation behavior with amorphous materials. The alloy's annealing time dependence of recovery enthalpy follows a stretched exponential function with the mean relaxation time obeying an Arrhenius law. The equilibrium recovery enthalpy ΔH_T^eq, mean relaxation time τ and stretching exponent β are all dependent on the annealing temperature, and generally, a higher annealing temperature comes with a lower value of ΔH_T^eq, τ and a higher value of β. Two parameters, β_g and τ_g, representing the stretching exponent and the mean structural relaxation time at the calorimetric glass transition temperature, respectively, are correlated with glass forming ability and thermal stability, respectively. For Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈ BMG, the high value of β_g, which is much higher than 0.84 and approaches unity, reveals its good glass forming ability, while, on the other hand, the low value of τ_g indicates a worse thermal stability compared with typical BMGs.     

Combined in-situ SAXS/WAXS and HRTEM study on crystallization of (Cu60Co40)1 − xZrx metallic glasses

CuZr as well as CoZr are well known metallic glass-formers in a wide compositional range. Since the binary Cu-Co system exhibits a metastable liquid-liquid miscibility gap, i.e. Cu and Co tend to separate from each other, the ternary Cu-Co-Zr system is a promising candidate to form phase separated glass-glass composites. In this work (Cu₆₀Co₄₀)_1 − xZr_x metallic glasses with relatively low Zr contents of x = 37 and x = 32 were prepared by melt spinning and investigated by in-situ small-angle and wide-angle X-ray scattering (SAXS/WAXS) and differential scanning calorimetry (DSC). Certain heat treated samples were additionally investigated by high-resolution transmission electron microscopy (HRTEM). Even for x = 32 there are no indications for any kind of phase separation in the as-quenched state within experimental resolution, i.e. the critical temperature T_c for a liquid-liquid phase separation has already decreased from 1556 K for binary Cu₆₀Co₄₀ to a temperature below the glass transition temperature T_g = 762(5)K found for (Cu₆₀Co₄₀)₆₈Zr₃₂. Combined in-situ SAXS/WAXS and HRTEM investigations reveal that thermal annealing also does not induce an amorphous-amorphous phase separation. Instead the formation of nano crystallites of a so far unknown Cu-rich/Zr-poor phase with relatively low activation energy for crystallization E_a = 116(7) kJ/mol at temperatures far below the crystallization temperature deduced from DSC measurements is observed.     

Influence of TM and RE elements on glass formation of the ternary Al-TM-RE systems

The effects of TM and RE elements on glass formation ability (GFA) of the Al-TM-RE systems are studied systematically. The TM elements show distinct differences: critical sizes of the Al-TM-Ce systems are in the order of Ni > Co > Fe > Cu. However, the RE elements show similar effect on glass formation. These results are discussed in terms of the GFA-related factors, i.e., reduced glass transition temperature (T_rg = T_g (T_x)/T_L, where T_g, T_x and T_L are the glass transition temperature, onset crystallization temperature and liquidus temperature, respectively) and the mixing enthalpy ΔH_Al-TM. A new parameter of T_L − T_g (T_x) is potentially proposed and used to evaluate the GFA of the Al-based alloys, as well as bulk glass-formers.     

Non-isothermal crystallization kinetics study on new amorphous Ga20Sb5S75 and Ga20Sb40S40 chalcogenide glasses

Bulk glasses of the system Ga₂₀Sb_xS_80−x (x = 5 and 40) were prepared for the first time by the known melt quenching technique. Non-isothermal differential scanning calorimetric (DSC) measurements of as-quenched Ga₂₀Sb_xS_80−x (x = 5 and 40) chalcogenide glasses reveal that the characteristic temperatures e.g. the glass transition temperature (T_g), the temperature corresponding to the maximum crystallization rate (T_p) recorded in the temperature range 400-650 K for x = 5 and 480-660 K for x = 40 are strongly dependent on heating rate and Sb content. Upon heating, these glasses show a single glass transition temperature (T_g) and double crystallization temperatures (T_p1 and T_p2) for x = 5 which overlapped and appear as a single crystallization peak (T_p) for x = 40. The activation energies of crystallization E_c were evaluated by three different methods. The crystallization data were examined in terms of recent analysis developed for non-isothermal conditions. The crystalline phases resulting from (DSC) have been identified using X-ray diffraction.     

Modeling and measurement of residual stresses in a bulk metallic glass plate

The recent advent of multi-component alloys with exceptional glass forming ability has allowed the processing of large metallic specimens with amorphous structure. The possibility of formation of thermal tempering stresses during the processing of these bulk metallic glass (BMG) specimens was investigated using two models: (i) instant freezing model, and (ii) viscoelastic model. The first one assumed a sudden transition between liquid and elastic solid at the glass transition temperature. The second model considered the equilibrium viscosity of BMG. Both models yielded similar results although from vastly different approaches. It was shown that convective cooling of Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 plates with high heat transfer coefficients could potentially generate significant compressive stresses on the surfaces balanced with mid-plane tension. The crack compliance (slitting) method was then employed to measure the stress profiles in a BMG plate that was cast in a copper mold. These profiles were roughly parabolic suggesting that thermal tempering was indeed the dominant residual stress generation mechanism. However, the magnitude of the measured stresses (with peak values of only about 1.5% of the yield strength) was significantly lower than the modeling predictions. Possible reasons for this discrepancy are described in relation to the actual casting process and material properties. The extremely low residual stresses measured in these BMG specimens, combined with their high strength and toughness, serve to further increase the advantages of BMGs over their crystalline metal counterparts.     

The effect of Sn addition on the glass-forming ability of Cu-Ti-Zr-Ni-Si metallic glass alloys

The effect of Sn substitution for Ni on the glass-forming ability was studied in Cu₄₇Ti₃₃Zr₁₁Ni_8−xSn_xSi₁ (x=0,2,4,6,8) alloys by using thermal analysis and X-ray diffractometry. With increasing x from 0 to 8, the glass transition temperature, T_g, of melt-spun Cu₄₇Ti₃₃Zr₁₁Ni_8−xSn_xSi₁ alloys increased gradually from 720 to 737 K. On the other hand, the crystallization temperature, T_x, increased from 757 K at x=0 to 765 K at x=2, being nearly same with further increase of x. Partial substitution of Ni by Sn in Cu₄₇Ti₃₃Zr₁₁Ni₈Si₁ promotes the glass formation. Both amorphous Cu₄₇Ti₃₃Zr₁₁Ni_8−xSn_xSi₁ alloys prepared by melt spinning and injection casting showed similar crystallization process during continuous heating in DSC. Temperature range of undercooled liquid region exhibits good correlation with the critical diameter for the formation of an amorphous phase in injection casting.     

Crystal growth and characterization of two-leg spin ladder compounds: Sr14Cu24O41 and Sr2Ca12Cu24O41

Single crystals of Sr_14−xCa_xCu₂₄O₄₁ (x=0 and 12) are grown by the travelling solvent floating zone technique using an image furnace. The grown crystals are characterized for their single crystallinity by the X-ray and Neutron Laue method. The magnetic susceptibility measurements in Sr₁₄Cu₂₄O₄₁ show considerable anisotropy along the main crystallographic axes. Low-temperature specific heat measurement and DC susceptibility measurement in Ca-doped crystal showed antiferromagnetic ordering at 2.8 K at ambient pressure. High-pressure AC susceptibility measurement on Ca-doped crystal showed a sharp superconducting transition at 2 K under 40 kbars. T_c onset reached a maximum value of 9.9 K at 54 kbars. The bulk superconductivity of the sample is confirmed by the high-pressure AC calorimetry with T_c max=9.4 K and T_N=5 K at 56 kbars.