Structural study of (As2S3)0.6(GeS2)0.4 glass

(As₂S₃)_0.6(GeS₂)_0.4 glass in non-irradiated and γ-irradiated states has been studied by using high-energy synchrotron X-ray diffraction, extended X-ray absorption fine structure spectroscopy, and positron annihilation lifetime spectroscopy. The experimental results are explained by the local changes around As and Ge atoms upon irradiation. These changes are suggested to involve chemical bonds distortion, formation of defective bonds with wrong coordination, rotation of structural units and appearance of additional free volume in the glass network.     

The electronic properties of glasses in the Cux(As0.4Se0.6)100−x system with x between 5 and 30

Data are presented on the dc conductivity, thermopower and optical absorption of glasses in the CuAs₂Se₃ system. The electronic properties of the alloys differ markedly from those of As₂Se₃, but variations in composition do not introduce significant changes in properties, until the atomic percent of copper is greater than 25. The results are interpreted in terms of small polaron transport.     

Influence of rare earth elements on crystallization of Fe82Nb2B14RE2 (RE = Y, Gd, Tb, and Dy) amorphous alloys

The work concerns influence of rare earth elements on crystallization of Fe₈₂Nb₂B₁₄RE₂ (RE = Y, Gd, Tb, and Dy) group of amorphous alloys. The samples were obtained by typical melt spinning technique. The crystallization studies were carried out with the use of (i) differential scanning calorimetry (DSC) in the temperature range from 300 K to 850 K with different heating rates and (ii) standard magnetic balance (Faraday type). The crystalline structure before and after the first stage of crystallization were checked by XRD and HRTEM techniques. The measurements allow the determining crystallization temperatures, activation energies of crystallization, average size of nanograins formed during crystallization and the Curie temperatures. In the paper all the obtained results are widely discussed in the context of different rare earth alloying additions.     

EXAFS studies of the Ni66Y33 and Cu60Zr40 amorphous alloys: A modelling of the pair distribution function with two subshells

Disorder effects in amorphous Ni₆₆Y₃₃ and Cu₆₀Zr₄₀ alloys have been investigated by the EXAFS technique. EXAFS spectra have been fitted using a double pair distribution function for the TM-TM (transition metal) pairs and for the unlike atom pairs. Both alloys have been found to be chemically ordered. For Cu₆₀Zr₄₀ the amorphous structure is very similar to the crystalline one.     

Thermal dissolution of Ag(Cu) in amorphous Ge(Sx Se1 − x)2 system

Thermally induced solid state reaction of Ag(Cu) into thin Ge(S_x Se_1 − x)₂ films with x = 0, 0.1, 0.4 and 1.0 was investigated using a step by step technique in order to design films with exact Ag(Cu) concentrations for applications in integrated IR optical devices. A thin film of Ag(Cu) was deposited on top of the host Ge(S_x Se_1 − x)₂ films followed by annealing in vacuum at constant temperature, which resulted in homogeneous films of good optical quality. The variation in Ag(Cu) concentration in the films ranged between 5 and 35 at.%. The kinetics of the diffusion and dissolution of metal in the host films was measured by optically monitoring the change in thickness of doped chalcogenide during consecutive thermal annealing steps. The kinetics studies revealed that the thermal dissolution rate of the Cu is greater than that of Ag. Optical UV-VIS transmission spectra of chalcogenide glass layers, undoped and thermal doped by Ag(Cu), were measured to establish the optical properties of the films. The spectra were analyzed using the technique proposed by Swanepoel and the results show that the addition of metal increases the absorption coefficient in the power-law regime and consequently the optical gap decreases and the refractive index increases. The amorphous character of the films was checked by X-ray diffraction which confirmed the amorphous structure of all Ag(Cu)GeSSe thin films.     

Boron content dependance of magnetoimpedance in Fe91−xZr5BxNb4 alloys

A systematic investigation of the influence of B content on the magnetoimpedance (MI) effect in melt-spun Fe_91−xZr₅B_xNb₄ (FZBN, 0 ? x ? 30) ribbons has been performed within a frequency range, f ∼ 310-1110 kHz and under a varying dc magnetic field (H_dc) up to 70 Oe. The MI effect is not observed in the sample with x ? 5 but within the range 8 ? x ? 30. A distinct MI effect has been observed with a maximum change of 180% at around 1.1 MHz in the sample with x = 20, coincident with a saturation magnetic field of 66 Oe and a field sensitivity of about 7%/Oe. Magnetic measurements reveal that the MI effect and B content dependence of the effect are closely related to coercivity of the FZBN alloy series, except for the sample with 20 at.%. The drastic MI ratio observed in the sample with x = 20 is ascribed to its special microstructure. The mechanism of the MI effect in FZBN alloys and of the significant MI value appearing at a B content of x = 20 is discussed in this paper.     

Synthesis and crystal structure of rare earth selenates Nd(HSeO4)3, Sm(HSeO4)3, and Nd2(SeO4)3 · 5H2O

Single crystals of rare earth (RE) selenates of the compositions Nd(HSeO₄)₃, Sm(HSeO₄)₃, and Nd₂(SeO₄)₃ · 5H₂O are synthesized and studied by X-ray diffraction analysis at T = 297 and 180 K. It is established that Nd and Sm hydrogen selenates are isostructural to one another and to the corresponding hydrogen sulfates. Neodymium selenate pentahydrate is not isostructural to the analogous RE sulfates, although their structural motifs are similar. __________ Translated from Kristallografiya, Vol. 49, No. 5, 2004, pp. 835–840. Original Russian Text Copyright ? 2004 by Zakharov, Troyanov, Kemnitz.     

Crystal and Molecular Structures of C6H5CH2SOCH2CONHCH2C6H5 and C6H5SOCH2CON(iC3H7)2

Abstract  The crystal structures for two of the ligands C₆H₅CH₂SOCH₂CONHCH₂C₆H₅ (1) and C₆H₅SOCH₂CON(ⁱC₃H₇)₂ (2) have been determined by X-ray diffraction. These compounds crystallize in orthorhombic system with space groups and cell parameters, Pca21(no. 29), a = 8.4600(5) ?, b = 5.3534(5) ?, c = 32.136(2) ?, V = 1455.42(15) ?³ and Pna21(no. 33) a = 17.5563(11) ?, b = 5.7902(4) ?, c = 14.2866(9) ?, V = 1452.30(16) ?³, respectively. These molecules are stabilized in solid state by various intra and intermolecular hydrogen bonding interactions to give polymeric structures. The reported IR spectra of these compounds in solid state could be explained on the basis of the observed intermolecular hydrogen bonding interactions. Index Abstract  The title compounds C₆H₅CH₂SOCH₂CONHCH₂C₆H₅ (1) and C₆H₅SOCH₂CON(ⁱC₃H₇)₂ (2) were prepared by the oxidation of corresponding sulfides with H₂O₂/SeO₂ in methanol and their structures were determined. The structures show that the SO and CO groups are having “anti” configuration in 1 and “syn” configuration in 2. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Pincer ligand coordination at Co3 and Ru6 clusters: Syntheses, reactivity studies, and X-ray diffraction structures of [PhCCo3(CO)8]2(dppx) and [Ru6(μ6-C)(CO)16]2(dppx)

The reaction of the pincer diphosphine ligand 4,6-bis(diphenylphosphinomethyl)-m-xylene (dppx) with the metal cluster compounds PhCCo₃(CO)₉ and Ru₆(μ₆-C)(CO)₁₇ has been explored. Both clusters react with dppx to afford the simple substitution products [PhCCo₃(CO)₈]₂(dppx) and [Ru₆(μ₆-C)(CO)₁₆]₂(dppx), where two cluster units are tethered by the pincer ligand. The molecular structures of the title products and the 2:1 cluster-pincer ligand stoichiometry have been established by X-ray crystallography. The stability of [PhCCo₃(CO)₈]₂(dppx) and [Ru₆(μ₆-C)(CO)₁₆]₂(dppx) has been investigated under gentle thermolysis conditions (ca. 55–65°C). Both dppx-substituted clusters are unstable with [PhCCo₃(CO)₈]₂(dppx) decomposing and [Ru₆(μ₆-C)(CO)₁₆]₂(dppx) transforming into the diphosphine-bridged cluster Ru₆(μ₆-C)(CO)₁₅(μ-dppx) as the major observable product. The identity of the latter cluster has been ascertained by IR and NMR spectroscopies and mass spectrometry.     

(La0.5Sr0.5)CoO3为电极的Pb(Zr0.4Ti0.6)O3和Pb(Zr0.2Ti0.8)O3铁电电容器结构及电学性能

分别采用磁控溅射法和溶胶-凝胶法(Sol-gel)制备了(La0.5Sr0.5)CoO3(LSCO)和Pb(Zr1-xTix)O3(PZT)薄膜,在Pt(111)/Ti/SiO2/Si基片上构架了LSCO/Pb(Zr0.4Ti0.6)O3(PZT(40/60))/LSCO和LSCO/Pb(Zr0.2Ti0.8)O3(PZT(20/80))/LSCO铁电电容器,研究了两种铁电电容器的结构和性能。XRD结构分析表明:两种四方相的不同Zr/Ti比例的PZT薄膜均为结晶良好的多晶钙钛矿结构。在5 V测试电压下,LSCO/PZT(40/60)/LSCO和LSCO/PZT(20/80)/LSCO两种铁电电容器的剩余极化强度(Pr)和矫顽场(Ec)分别为:28μC/cm2和1.2 V以及32μC/cm2和2 V。相对于PZT(40/60),PZT(20/80)具有较大的剩余极化强度和矫顽场,是由于其矩形度(c/a)较大。两种电容器都具有较好的脉宽依赖性和抗疲劳性。在5 V的测试电压下,LSCO/PZT(40/60)/LSCO电容器的漏电流密度为3.2×10-5A/cm2,LSCO/PZT(20/80)/LSCO电容器的漏电流密度为3.11×10-4A/cm2,经拟合分析发现:在0～5 V的范围内,两种电容器都满足欧姆导电机制。     

含Ni-Nb阻挡层的硅基Pb(Zr0.4,Ti0.6)O3电容器的制备及铁电性能研究

采用Ni-Nb薄膜作为导电阻挡层,以La0.5Sr0.5CoO3(LSCO)为底电极,构建了LSCO/Pb(Zr0.4,Ti0.6)O3(PZT)/LSCO异质结电容器。使用X射线衍射仪和铁电测试仪对其进行结构表征和性能测试。实验发现:Ni-Nb薄膜为非晶结构,PZT薄膜结晶状况良好。LSCO/PZT/LSCO电容器在5 V外加电压测试下,电滞回线具有良好的饱和趋势,剩余极化强度Pr为35.5μC/cm2,矫顽电压Vc为1.42 V,电容器具有良好的抗疲劳特性和保持特性。     

Pressure and heating rate dependence of the crystallization temperature for amorphous (Fe65Ni35)75P16B6Al3 and Ti50Be40Zr10

The crystallization temperature, T_x, was determined at constant heating rate, $\text{R =}\text{T}\text{?}\text{? 7}\text{K min}{}^{\mathrm{?1}}$, by monitoring the electrical resistance. Such experiments were carried out under pressures up to 2.5 GPa, and the resulting dT_x/dP was 15.9 K GPa^?1 for (Fe₆₅Ni₃₅)₇₅P₁₆B₆Al₃ and 8.7 K GPa^?1, 8.1 K GPa^?1 for the two crystallization processes in Ti₅₀Be₄₀Zr₁₀. The activation energies of crystallization under atmospheric pressure were obtained from measurements of T_x at rates from 0.05 K min^?1 ?55 K min^?1, analysed by plotting ln(T_x²R^?1) versus T_x^?1.     

Structure and properties of Ni60(Nb100−xTax)34Sn6 bulk metallic glass alloys

Refractory bulk metallic glasses and bulk metallic glass composites are formed in quaternary Ni-Nb-Ta-Sn alloy system. Alloys of composition Ni₆₀(Nb_100−xTa_x)₃₄Sn₆ (x = 20, 40, 60, 80) alloys were prepared by injection-casting the molten alloys into copper molds. Glassy alloys are formed in the thickness of half mm strips. With thicker strips (e.g., 1 mm), Nb₂O₅ and Ni₃Sn phases and the amorphous phase form an in situ composite. Glass transition temperatures, crystallization temperatures, and ΔT_x, defined as T_x1 − T_g (T_x1: first crystallization temperature, T_g: glass transition temperature) of the alloys increase dramatically with increasing Ta contents. These refractory bulk amorphous alloys exhibit high Young’s modulus (155-170 GPa), shear modulus (56-63 GPa), and estimated yield strength (3-3.6 GPa).     

YAl3(BO3)4: Crystal growth and characterization

The growth and characterization of YAl₃(BO₃)₄ (YAB), a potential nonlinear optical crystal for the fourth harmonic generation of Nd:YAG laser, was reported. Using top-seeded solution growth method, a YAB crystal with the dimensions of 16×16×18 mm³ was obtained from B₂O₃–Li₂O flux system. The advantages of this flux system and the growth process were discussed in detail. The as-grown YAB crystal was verified by powder X-ray diffraction. The transparency spectra indicated that the cut-off edge of the as-grown YAB was 170 nm. The fourth harmonic generation of a frequency doubled Nd:YAG laser, from 532 to 266 nm, was carried out with a YAB crystal doubler for the first time. Output pulse power obtained was 2.4 mW at 266 nm and the conversion efficiency from 532 to 266 nm was about 15.6%.     

Short-range order in ultrafine powder of an amorphous (Fe7Ni3)69B31 alloy

The short-range order structure of ultrafine powder of an amorphous (Fe₇Ni₃)₆₉B₃₁ alloy has been studied by ZAFS. The particles with diameters 1.7–15.3 nm are prepared by chemical reduction. The fact that the local environments around Fe or Ni are not the same suggests that there is chemical short-range order in this material. The mean distances of near neighbors surrounding an Fe and a Ni atom are shorter than those in amorphous Fe₈₀B₂₀ ribbon. The XANES spectra also show some differences between these two amorphous alloys. These indicate that the interaction between near neighbors is stronger in this amorphous ultrafine powder than in bulk amorphous material.     

Growth and shape control of orthorhombic Fe5(PO4)4(OH)3·2H2O single crystalline dendrites

Orthorhombic Fe₅(PO₄)₄(OH)₃·2H₂O single crystalline dendritic nanostructures have been synthesized by a facile and reproducible hydrothermal method without the aid of any surfactants. The influences of synthetic parameters, such as reaction time, temperature, the amount of H₂O₂ solution, pH values, and types of iron precursors, on the crystal structures and morphologies of the resulting products have been investigated. The formation process of Fe₅(PO₄)₄(OH)₃·2H₂O dendritic nanostructures is time dependent: amorphous FePO₄·nH₂O nanoparticles are formed firstly, and then Fe₅(PO₄)₄(OH)₃·2H₂O dendrites are assembled via a crystallization-orientation attachment process, accompanying a color change from yellow to green. The shapes and sizes of Fe₅(PO₄)₄(OH)₃·2H₂O products can be controlled by adjusting the amount of H₂O₂ solution, pH values, and types of iron precursors in the reaction system.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

A novel representative {[Rb1.94(H2O,OH)3.84](H2O)0.1}{Al4(OH)4[PO4]3} in the pharmacosiderite structure type

The crystal structure of a new synthetic aluminophosphate {[Rb_1.94(H₂O,OH)_3.84](H₂O)_0.1}{Al₄(OH)₄[PO₄]₃} synthesized under mild hydrothermal conditions (T = 280°C, P = 100 atm) in the Rb₂O-Al₂O₃-P₂O₅-H₂O system is determined using X-ray diffraction (Stoe IPDS diffractometer, λMoK _α, graphite monochromator, 2θ_max = 64.33°, R = 0.032 for 312 reflections). The main crystal data are as follows: a = 7.4931(6) ?, space group P 3m, Z = 1, and ρ_calcd = 2.76 g/cm³. It is shown that the synthesized compound belongs to the pharmacosiderite structure type with a characteristic mixed open microporous framework composed of octahedra and tetrahedra. A comparative crystal chemical analysis of related phases is performed, and the chemical compositions of promising absorbents, i.e., hypothetical compounds potentially possible in the structure type under consideration, are proposed. It is established that pharmacosiderite and rhodizite are homeotypic to each other. Original Russian Text ? O.V. Yakubovich, W. Massa, O.V. Dimitrova, 2008, published in Kristallografiya, 2008, Vol. 53, No. 3, pp. 442–449.     

Effect of the number of defect density waves on the dynamics of the soliton system in [N(CH3)4]2CuCl4 and [N(CH3)4]2Zn0.98Ni0.02Cl4 crystals

The time dependences of the birefringence and thermal conductivity of [N(CH₃)₄]₂CuCl₄ and [N(CH₃)₄]₂Zn_0.98Ni_0.02Cl₄ crystals in the incommensurate phase at a constant temperature have been studied. A multiwave state of modulated superstructure is found to be formed in the presence of defect density waves in the crystal. It is shown that, depending on the number of defect density waves in the crystal, either a superposition of existing modulation waves or a domainlike structure arise in it.