Electrical properties of AsxSe1−x (x ≤ 0.05) Mott-barriers

We have experimentally measured the current-voltage and capacitance-voltage characteristics of Au/amorphous As_xSe_1 − x (x ≤ 0.05)/Zr trilayer structures at temperatures from 4 to 295 K. The observed capacitance of structures with an amorphous As_xSe_1 − x (a-As_xSe_1 − x) thickness of ~ 0.4 to ~ 2.8 μm does not significantly change over the entire range of applied bias (− 5 V to 5 V), indicating that the a-As_xSe_1 − x films are fully depleted and thus the structures are Mott barriers. The current-voltage (I-V) characteristics of the a-As_0.03Se_0.97 device at low (< 3000 V/cm) to moderate fields (3000 V/cm-10000 V/cm) follow the predictions of trap limited space charge conduction theory, as they exhibit Ohmic behavior at low fields and trap limited space charge current at moderate fields. According to the trap limited space charge current model of Lampert, the a-As_0.03Se_0.97 film has an effective hole mobility, Θμ (with Θ < 1), of ~ 5 × 10^− 7 cm²/V-sec at 295 K. This value is similar to, but consistently lower than previously reported mobilities inferred from time of flight measurements. The current at high fields (> 10⁴ V/cm) increases rapidly with applied field as a result of carrier emission from localized states and is consistent with transport by the Poole-Frenkel mechanism. A permanent transition to a high conductance state (~ 10^− 3 S) is observed after exposure to very high electric fields (~ 4 × 10⁵V/cm).     

Random anisotropy studies in amorphous Co-Er-B ribbons

We have studied the magnetization of melt-spun amorphous Co_80 − xEr_xB₂₀ alloys with 0 ≤ x ≤ 7.5 under magnetic fields of up to 50 kOe, and have analyzed the results at 4.2 K on the basis of the random magnetic anisotropy model. The approach to saturation is established in the form of H^−1/2 for various samples. The saturation magnetization, coherent anisotropy constant, local random anisotropy constant and the ferromagnetic correlation length were studied as a function of the Er composition.     

Low-temperature/high-temperature AlN superlattice buffer layers for high-quality AlxGa1−xN on Si (1 1 1)

We present MOVPE-grown, high-quality Al_xGa_1−x N layers with Al content up to x=0.65 on Si (1 1 1) substrates. Crack-free layers with smooth surface and low defect density are obtained with optimized AlN-based seeding and buffer layers. High-temperature AlN seeding layers and (low temperature (LT)/high temperature (HT)) AlN-based superlattices (SLs) as buffer layers are efficient in reducing the dislocation density and in-plane residual strain. The crystalline quality of Al_xGa_1−xN was characterized by high-resolution X-ray diffraction (XRD). With optimized AlN-based seeding and SL buffer layers, best ω-FWHMs of the (0 0 0 2) reflection of 540 and 1400 arcsec for the (1 0 1¯ 0) reflection were achieved for a ∼1-μm-thick Al_0.1Ga_0.9N layer and 1010 and 1560 arcsec for the (0 0 0 2) and (1 0 1¯ 0) reflection of a ∼500-nm-thick Al_0.65Ga_0.35N layer. AFM and FE-SEM measurements were used to study the surface morphology and TEM cross-section measurements to determine the dislocation behaviour. With a high crystalline quality and good optical properties, Al_xGa_1−x N layers can be applied to grow electronic and optoelectronic device structures on silicon substrates in further investigations.     

Transport property and structural characterization studies on (1 − x)[0.75AgI:0.25AgCl]:xTiO2 conducting composite electrolyte system

Transport property and structural investigation have been carried out on newly synthesized Ag⁺ ion conducting composite electrolyte system. The composite electrolyte system (1 − x)[0.75AgI:0.25AgCl]:xTiO₂, where 0 ? x ? 0.5 (in molar weight fraction) has been synthesized by melt quenching and annealing methods. The chemical compound TiO₂ (second phase dispersoid) dispersed in different compositions in a quenched (0.75AgI:0.25AgCl) mixed system/solid solution; this solid solution was used as a first phase host salt in place of AgI. The different preparation routes were adopted for the composite electrolyte system. Composition x = 0.1 exhibited highest conductivity at room temperature. The composite system 0.9[0.75AgI:0.25AgCl]:0.1TiO₂ was synthesized at different soaking times by melt quenching method. The system exhibited optimum conductivity at 20 min soaking time (σ_rt ≈ 1.4 × 10⁻³ S/cm). The ac conductivity has been measured from Z′-Z″ (Cole-Cole) complex impedance plots using impedance spectroscopic (IS) technique. The electrical conductivity as a function of temperature and frequency has been studied, and activation energy E_a, was calculated from Arrhenius plots for all compositions (0 ? x ? 0.5). The dc conductivity value has been evaluated from Log σ vs. log f plots. Structural characterization studies were carried out by X-ray diffraction (XRD) and differential thermal analysis (DSC) techniques.     

Effects of Nb2O5 Replacement by Er2O3 on elastic and structural properties of 75TeO2-(10 − x)Nb2O5-15ZnO-(x)Er2O3 glass

Tellurite 75TeO₂-(10 − x)Nb₂O₅-15ZnO-(x)Er₂O₃; (x = 0.0-2.5 mol%) glass system with concurrent reduction of Nb₂O₅ and Er₂O₃ addition have been prepared by melt-quenching method. Elastic properties together with structural properties of the glasses were investigated by measuring both longitudinal and shear velocities using the pulse-echo-overlap technique at 5 MHz and Fourier Transform Infrared (FTIR) spectroscopy, respectively. Shear velocity, shear modulus, Young's modulus and Debye temperature were observed to initially decrease at x = 0.5 mol% but remained constant between x = 1.0 mol% to x = 2.0 mol%, before increasing back with Er₂O₃ addition at x = 2.5 mol%. The initial drop in shear velocity and related elastic moduli observed at x = 0.5 mol% were suggested to be due to weakening of glass network rigidity as a result of increase in non-bridging oxygen (NBO) ions as a consequence of Nb₂O₅ reduction. The near constant values of shear velocity, elastic moduli, Debye temperature, hardness and Poisson's ratio between x = 0.5 mol% to x = 2.0 mol% were suggested to be due to competition between bridging oxygen (BO) and NBO ions in the glass network as Er₂O₃ gradually compensated for Nb₂O₅. Further addition of Er₂O₃ (x > 2.0 mol%) seems to further reduce NBO leading to improved rigidity of the glass network causing a large increase of ultrasonic velocity (v_L and v_S) and related elastic moduli at x = 2.5 mol%. FTIR analysis on NbO₆ octahedral, TeO₄ trigonal bipyramid (tbp) and TeO₃ trigonal pyramid (tp) absorption peaks confirmed the initial formation of NBO ions at x = 0.5 mol% followed by NBO/BO competition at x = 0.5-2.0 mol%. Appearance of ZnO₄ tetrahedra and increase in intensity of TeO₄ tbp absorption peaks at x = 2.0 mol% and x = 2.5 mol% indicate increase in formation of BO.     

Spectrometric and ellipsometric studies of (1 − x)TiO2 · xLn2O3 (Ln = Nd, Sm, Gd, Er, Yb) thin films

Spectrometric and ellipsometric studies of (1 − x)TiO₂ · xLn₂O₃ (Ln = Nd, Sm, Gd, Er, Yb; x = 0.33, 0.5) thin films at room temperature were performed. The obtained dispersion dependences of refractive indices are successfully described by the optical-refractometric relation. The dependence of optical pseudogap and refractive indices on composition and molar mass of the films is investigated. The influence of compositional disordering on the energy width of the exponential absorption edge is studied.     

Crystal/glass phase change in K1−xRbxSb5S8 (x = 0.25, 0.50, 0.75) studied through thermal analysis techniques

K_1−xRb_xSb₅S₈ (x = 0.25, 0.5, 0.75) is a well-defined single-phase system that undergoes a reversible phase-change. We determined the activation energy of glass transition and crystallization, respectively, for the three compositions using the Kissinger and Ozawa-Flynn-Wall equations. The results have shown that for K_0.25Rb_0.75Sb₅S₈ the crystallization mechanism could be interpreted in terms of a single-step reaction. For the other two compositions the glass-to-crystal transformation is a process of increasing mechanistic complexity with time and it involves simultaneously several different nucleation and growth events. The slope of the lines in the Avrami plots was observed to be independent of heating rate for K_0.25Rb_0.75Sb₅S₈ and the mean value of the activation energy was found to be 262 ± 6 kJ/mol. For the other two compositions, the slope varies with the heating rate. In the K_0.25Rb_0.75Sb₅S₈ glasses, bulk nucleation with three-dimensional crystal growth appears to dominate the phase-change process.     

Insulator-like electrical transport in structurally ordered Al65Cu20+xRu15−x (x = 1.5, 1.0, 0.5, 0.0 and −0.5) icosahedral quasicrystals

Low-temperature resistivities, in zero-field and 8 T field, and magnetoresistance have been measured down to 1.4-300 K for stable icosahedral quasicrystals Al₆₅Cu_20+xRu_15−x (x = 1.5, 1.0, 0.5, 0.0 and −0.5). The analysis of the magnetoresistance data shows an overwhelming presence of anti weak-localization effect (τ_so ∼ 10⁻¹² s). But the sample with x = −0.5 shows anomalous magnetoresistance and the anti weak-localization effect breaks down (τ_so to be 10⁻¹⁵ s). The in-field σ-T between 5 K and 20 K, for x = 1.0, 0.5, 0.0 and −0.5 samples, and between 1.4 K and 40 K for x = 1.5 sample, follow a power-law behavior with an exponent of 0.5 and above ∼30 K the exponent ranges from 1.17 to 1.58. The observed power-laws basically characterize the presence of critical regime of the metal-insulator (MI) transition, dominated by electron-electron and electron-phonon inelastic scattering events respectively. In samples with x = 1.0, 0.5, 0.0 and −0.5 the in field σ-T has been found to follow ln σ-vs-T^1/4 below 5 K, which indicates the presence of variable range hopping. The observed transport features indicate the occurrence of proximity of metal-insulator transition in these Al-Cu-Ru quasicrystal samples.     

Effect of carbon on the microstructural evolution of Zr66.7−xNi33.3Cx (x = 0, 1, 3) alloys during mechanical alloying

In the present paper, the effect of carbon on the microstructural evolution of Zr_66.7−xNi_33.3C_x (x = 0, 1, 3) alloys during mechanical alloying has been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that these three alloys undergo similar amorphization and crystallization processes, and the final milling product is a metastable fcc-Zr_66.7−xNi_33.3C_x phase. The carbon addition can shorten the milling time for the complete amorphization reaction and enhance the stability of the formed amorphous alloy, which can suppress the mechanically induced amorphous-crystalline phase transformation with further increasing milling time.     

Combined in-situ SAXS/WAXS and HRTEM study on crystallization of (Cu60Co40)1 − xZrx metallic glasses

CuZr as well as CoZr are well known metallic glass-formers in a wide compositional range. Since the binary Cu-Co system exhibits a metastable liquid-liquid miscibility gap, i.e. Cu and Co tend to separate from each other, the ternary Cu-Co-Zr system is a promising candidate to form phase separated glass-glass composites. In this work (Cu₆₀Co₄₀)_1 − xZr_x metallic glasses with relatively low Zr contents of x = 37 and x = 32 were prepared by melt spinning and investigated by in-situ small-angle and wide-angle X-ray scattering (SAXS/WAXS) and differential scanning calorimetry (DSC). Certain heat treated samples were additionally investigated by high-resolution transmission electron microscopy (HRTEM). Even for x = 32 there are no indications for any kind of phase separation in the as-quenched state within experimental resolution, i.e. the critical temperature T_c for a liquid-liquid phase separation has already decreased from 1556 K for binary Cu₆₀Co₄₀ to a temperature below the glass transition temperature T_g = 762(5)K found for (Cu₆₀Co₄₀)₆₈Zr₃₂. Combined in-situ SAXS/WAXS and HRTEM investigations reveal that thermal annealing also does not induce an amorphous-amorphous phase separation. Instead the formation of nano crystallites of a so far unknown Cu-rich/Zr-poor phase with relatively low activation energy for crystallization E_a = 116(7) kJ/mol at temperatures far below the crystallization temperature deduced from DSC measurements is observed.     

Three-dimensional structure of fast ion conducting 0.5Li2S + 0.5[(1 − x)GeS2 + xGeO2] glasses from high-energy X-ray diffraction and reverse Monte Carlo simulations

A high-energy X-ray diffraction study has been carried out on a series of 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses with x = 0.0, 0.1, 0.2, 0.4, 0.6 and 0.8. Structure factors were measured to wave vectors as high as 30 Å⁻¹ resulting in atomic pair distribution functions with high real space resolution. The three dimensional atomic-scale structure of the glasses was modeled by reverse Monte Carlo simulations based on the diffraction data. Results from the simulations show that at the atomic-scale 0.5Li₂S + 0.5[(1 − x)GeS₂ + xGeO₂] glasses may be viewed as an assembly of independent chains of (Li^+-S)₂GeS_2/2 and (Li^+-O)₂GeO_2/2 tetrahedra as repeat units, where the Li ions occupy the open space between the chains. The new structure data may help understand the reasons for the sharp maximum in the Li⁺ ion conductivity at x ∼ 0.2.     

The glass transition temperature and infrared absorption spectra of: (70−x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Glasses of the system: (70−x) TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by melt quench technique. Dependencies of their glass transition temperatures (T_g) and infrared (IR) absorption spectra on composition were investigated. It is found that the gradual replacement of oxides, TeO₂ by Li₂O, decreases the glass transition temperature and increases the fragility of the glasses. Also, IR spectra revealed broad weak and strong absorption bands in the investigated range of wave numbers from 4000 to 400 cm⁻¹. These bands were assigned to their corresponding bond modes of vibration with relation to the glass structure.     

Local structural,magnetic, and optical properties of Zn1−xFexO thin films

High quality Zn_1−xFe_xO thin films were deposited on α-sapphire$\alpha \text{-sapphire}$ substrates by RF magnetron sputtering. X-ray absorption fine structure measurements showed that the chemical valence of Fe ions in the films was a mixture of 2+ and 3+ states, and Fe ions substituted mainly for the Zn sites in the films. DC-magnetization measurements revealed ferromagnetic properties from 5 to 300 K. The photoluminescence measurements at 15 K showed a sharp main transition peak at 3.35 eV along with a broad impurity peak at 2.45 eV. The structural and magnetization analyses of the Zn_1−xFe_xO films strongly suggested that the ferromagnetism was the intrinsic properties of the films.     

Boron content dependance of magnetoimpedance in Fe91−xZr5BxNb4 alloys

A systematic investigation of the influence of B content on the magnetoimpedance (MI) effect in melt-spun Fe_91−xZr₅B_xNb₄ (FZBN, 0 ? x ? 30) ribbons has been performed within a frequency range, f ∼ 310-1110 kHz and under a varying dc magnetic field (H_dc) up to 70 Oe. The MI effect is not observed in the sample with x ? 5 but within the range 8 ? x ? 30. A distinct MI effect has been observed with a maximum change of 180% at around 1.1 MHz in the sample with x = 20, coincident with a saturation magnetic field of 66 Oe and a field sensitivity of about 7%/Oe. Magnetic measurements reveal that the MI effect and B content dependence of the effect are closely related to coercivity of the FZBN alloy series, except for the sample with 20 at.%. The drastic MI ratio observed in the sample with x = 20 is ascribed to its special microstructure. The mechanism of the MI effect in FZBN alloys and of the significant MI value appearing at a B content of x = 20 is discussed in this paper.     

Theoretical studies of the spin Hamiltonian parameters and the local structures for the tetragonal Cu centers in the LKB glasses

The spin Hamiltonian parameters (g factors g_∥, g_⊥ and the hyperfine structure constants A_∥, A_⊥) for the Cu²⁺ centers in the lithium potassium borate (LKB) glasses xLi₂O·(30 − x)·K₂O·70B₂O₃ (0 ≤ x ≤ 25) were theoretically studied using the high-order perturbation formulas of these parameters for a 3d⁹ ion in a tetragonally elongated octahedron. The [CuO₆]¹⁰⁻ clusters in the LKB glasses are found to suffer the relative elongations of about 3% along the tetragonal axis due to the Jahn-Teller effect. The concentration dependences of the g factors are illustrated by the approximately linear decrease of the cubic field parameter Dq as well as the increases of the covalency factor N and the relative elongation ratio ρ due to the slight expansion of the cell volume or bond lengths with increasing the Li₂O concentration x. Meanwhile, the slow non-linear increases of the hyperfine structure constants are described as the rough exponential increase of the core polarization constant κ with x due to the increase of the tetragonality of the systems. The theoretical spin Hamiltonian parameters and their concentration dependences show good agreement with the experimental data. To evaluate validity and applicability of the present theoretical model and formulas, the EPR results of the Cu²⁺ centers in similar lithium sodium borate (LNB) xLi₂O·(30 − x)·Na₂O·70B₂O₃ (5 ≤ x ≤ 25 mol%) glasses are also analyzed and compared with those in the LKB systems using the uniform model and formulas.     

Thermal dissolution of Ag(Cu) in amorphous Ge(Sx Se1 − x)2 system

Thermally induced solid state reaction of Ag(Cu) into thin Ge(S_x Se_1 − x)₂ films with x = 0, 0.1, 0.4 and 1.0 was investigated using a step by step technique in order to design films with exact Ag(Cu) concentrations for applications in integrated IR optical devices. A thin film of Ag(Cu) was deposited on top of the host Ge(S_x Se_1 − x)₂ films followed by annealing in vacuum at constant temperature, which resulted in homogeneous films of good optical quality. The variation in Ag(Cu) concentration in the films ranged between 5 and 35 at.%. The kinetics of the diffusion and dissolution of metal in the host films was measured by optically monitoring the change in thickness of doped chalcogenide during consecutive thermal annealing steps. The kinetics studies revealed that the thermal dissolution rate of the Cu is greater than that of Ag. Optical UV-VIS transmission spectra of chalcogenide glass layers, undoped and thermal doped by Ag(Cu), were measured to establish the optical properties of the films. The spectra were analyzed using the technique proposed by Swanepoel and the results show that the addition of metal increases the absorption coefficient in the power-law regime and consequently the optical gap decreases and the refractive index increases. The amorphous character of the films was checked by X-ray diffraction which confirmed the amorphous structure of all Ag(Cu)GeSSe thin films.     

Self organized nano crystallinity of magnetite precipitated from a 4.9Na2O · 33.3CaO · 17.1Fe2O3 · 44.7B2O3 glass

Glasses with the mol% composition 4.9Na₂O · 33.3CaO · 17.1Fe₂O₃ · 44.7B₂O₃ were melted, rapidly quenched using a twin roller technique, and subsequently tempered in the range from 550 to 620 °C. This led to the crystallization of magnetite with mean crystallite sizes in the 10-20 nm range. Using higher temperatures resulted in a larger quantity of formed crystallites and slightly larger mean crystallite sizes. Larger tempering times did not lead to substantial crystal growth. The time law of Ostwald ripening was not followed. This is explained by an increase in viscosity of the residual glassy phase during nucleation and crystal growth. Here, the smaller iron concentration near the crystals leads to higher viscosities and to the formation of a diffusional barrier around the crystals, which reduces further crystal growth. The crystallization stops, if T_g of the residual glassy phase is equal to the tempering temperature. Magnetite nano crystals with sizes in the 10-20 nm range offer a wide range of applications, such as the preparation of ferrofluids or of materials for medical diagnostics and therapy.     

Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.     

Photoluminescence and optical absorption in glassy AsxSe1−x

The photoluminescence and optical absorption spectra in glassy As_xSe_1−x with 0.08 ? x ? 0.40 are essentially independent of x. The PL spectra peak at approximately half the optical gap and the exponential slopes of the optical absorption edges are all approximately 75 meV. For x > 0.4, the PL peaks shift to higher energies, the widths of the PL spectra increase, and there is a strong component to the optical absorption well below the optical gap. Comparisons with ESR experiments in the As_xS_1−x system suggest the possibility of two PL peaks. The second PL peak and the optical absorption below the optical band gap for x > 0.4 are attributed to the presence of As-As bonds.     

Sodium tracer diffusion in glasses of the type (CaO·Al2O3)x(2 SiO2)1−x

Tracer diffusion coefficients of the radioactive isotope Na-22 were measured in glasses of the type (CaO·Al₂O₃)_x(2 SiO₂)_1−x to study the diffusion of sodium as a function of glass composition, x, temperature and initial water content. The diffusion of Na-22 in glasses diffusion-annealed in dry air can always be well described by a single tracer diffusion coefficient, but sometimes not in samples annealed in common air. It was found that the sodium tracer diffusion coefficient decreases by about six orders of magnitude when the glass composition x changes from 0 to 0.75 at 800 °C. The temperature dependence of the diffusion of sodium seems to decrease as the silica content increases. Variations of the initial water content in some of the glasses investigated did not very significantly influence the rate of the tracer diffusion of sodium.