An investigation of the kinetic transformation mechanism of Ge12.5Te87.5 chalcogenide glass under non-isothermal regime

Differential scanning calorimetry (DSC) technique was used to study the kinetics of amorphous to crystalline transformation in Ge_12.5Te_87.5 chalcogenide glass. The kinetic parameters of glassy Ge_12.5Te_87.5 under non-isothermal conditions are analyzed by the model-free and model-fitting approaches from a series of experiments at different constant heating rates (5-50 K/min). The effective activation energy of crystallization was determined by analyzing the data using the isoconversional methods of Kissinger-Akahira-Sunose (KAS), Tang, Starink, Flynn-Wall-Ozawa (FWO) and Vyazovkin. The analysis of the present data shows that the effective activation energy of crystallization is constant throughout the entire interval of conversions and hence with temperature. The transformation mechanism examined using the local Avrami exponents indicates that one mechanism (three-dimensional growth) is responsible for the transformation process for all heating rates used. The reaction model that may describe the transformation process of the Ge_12.5Te_87.5 chalcogenide glass is the Avrami-Erofeev model (g(α) = [− ln(1 − α)]^1/n) with n = 3 for all heating range at the whole range of crystallized fraction (α = 0.05-0.95). A good agreement between the experimental and the reconstructed (α-T) curves has been achieved. The transformation from amorphous to crystalline phase in Ge_12.5Te_87.5 chalcogenide glass demonstrates a single-step mechanism.     

Effects of Nb2O5 Replacement by Er2O3 on elastic and structural properties of 75TeO2-(10 − x)Nb2O5-15ZnO-(x)Er2O3 glass

Tellurite 75TeO₂-(10 − x)Nb₂O₅-15ZnO-(x)Er₂O₃; (x = 0.0-2.5 mol%) glass system with concurrent reduction of Nb₂O₅ and Er₂O₃ addition have been prepared by melt-quenching method. Elastic properties together with structural properties of the glasses were investigated by measuring both longitudinal and shear velocities using the pulse-echo-overlap technique at 5 MHz and Fourier Transform Infrared (FTIR) spectroscopy, respectively. Shear velocity, shear modulus, Young's modulus and Debye temperature were observed to initially decrease at x = 0.5 mol% but remained constant between x = 1.0 mol% to x = 2.0 mol%, before increasing back with Er₂O₃ addition at x = 2.5 mol%. The initial drop in shear velocity and related elastic moduli observed at x = 0.5 mol% were suggested to be due to weakening of glass network rigidity as a result of increase in non-bridging oxygen (NBO) ions as a consequence of Nb₂O₅ reduction. The near constant values of shear velocity, elastic moduli, Debye temperature, hardness and Poisson's ratio between x = 0.5 mol% to x = 2.0 mol% were suggested to be due to competition between bridging oxygen (BO) and NBO ions in the glass network as Er₂O₃ gradually compensated for Nb₂O₅. Further addition of Er₂O₃ (x > 2.0 mol%) seems to further reduce NBO leading to improved rigidity of the glass network causing a large increase of ultrasonic velocity (v_L and v_S) and related elastic moduli at x = 2.5 mol%. FTIR analysis on NbO₆ octahedral, TeO₄ trigonal bipyramid (tbp) and TeO₃ trigonal pyramid (tp) absorption peaks confirmed the initial formation of NBO ions at x = 0.5 mol% followed by NBO/BO competition at x = 0.5-2.0 mol%. Appearance of ZnO₄ tetrahedra and increase in intensity of TeO₄ tbp absorption peaks at x = 2.0 mol% and x = 2.5 mol% indicate increase in formation of BO.     

Crystallization kinetics in Cu46Zr45Al7Y2 bulk metallic glass by differential scanning calorimetry (DSC)

Crystallization transformation kinetics in isothermal and non-isothermal (continuous heating) modes were investigated in Cu₄₆Zr₄₅Al₇Y₂ bulk metallic glass by differential scanning calorimetry (DSC). In isochronal heating process, activation energy for crystallization at different crystallized volume fraction is analyzed by Kissinger method. Average value for crystallization in Cu₄₆Zr₄₅Al₇Y₂ bulk metallic glass is 361 kJ/mol in isochronal process. Isothermal transformation kinetics was described by the Johnson-Mehl-Avrami (JMA) model. Avrami exponent n ranges from 2.4 to 2.8. The average value, around 2.5, indicates that crystallization mechanism is mainly three-dimensional diffusion-controlled. Activation energy is 484 kJ/mol in isothermal transformation for Cu₄₆Zr₄₅Al₇Y₂ bulk metallic glass. These different results were discussed using kinetic models. In addition, average activation energy of Cu₄₆Zr₄₅Al₇Y₂ bulk metallic glass calculated using Arrhenius equation is larger than the value calculated by the Kissinger method in non-isothermal conditions. The reason lies in the nucleation determinant in the non-isothermal mode, since crystallization begins at low temperature. Moreover, both nucleation and growth are involved with the same significance during isothermal crystallization. Therefore, the energy barrier in isothermal annealing mode is higher than that of isochronal conditions.     

Thermal and some physical properties of glasses in the La2O3−CaO−B2O3 ternary system

Glasses in the La₂O₃−CaO−B₂O₃ ternary system were studied. The glass forming range as determined by the appearance of the annealed cast was found to match previously published findings. Clear glasses were formed in the composition range of 5.7−19.1 mol% La₂O₃ with constant B₂O₃ content of 71.4 mol%, and in glasses of constant La₂O₃:CaO ratio of 1:4 with B₂O₃ content in the range of 71.4-55.0 mol%. The non-linear optical crystalline phase La₂Ca₂B₁₀O₁₉ was crystallized from the clear glasses after heat treatments, as determined by powder XRD. Two types of the LaBO₃ crystalline phases were detected in the partially and the fully crystallized glass compositions outside the glass forming range. Data are reported for the glass transition temperature (T_g), dilatometric softening point (T_d), linear coefficient of expansion (α), onset crystallization temperature (T_x), exothermal peak temperature (T_P), density (ρ) and index of refraction (n_D) in the clear glasses.     

Crystallization kinetics determination of Pb15Ge27Se58 chalcogenide glass by using the various heating rates (VHR) method

The kinetics of crystallization of Pb₁₅Ge₂₇Se₅₈ was studied by differential scanning calorimetry non-isothermally. Various experimental methods are currently employed for determining the kinetic parameters of crystallization in a glassy system. These parameters include the activation energy of crystallization E (kJ/mol), the kinetic exponent n and the frequency factor K_o (s⁻¹). Recently, a new method (VHR method) has been derived from Johnson-Mehl-Avrami (JMA) transformation rate equation to calculate - in sequence - the crystallization kinetic parameters of a glassy system. The VHR technique has been used to estimate the crystallization parameters of Pb₁₅Ge₂₇Se₅₈ chalcogenide glass under non-isothermal conditions. The average value of E, n and K_o are found equal to 181.74 ± 0.58 (kJ/mol), 1.085 ± 0.023 and (9.196 ± 0.716) × 10¹² (s⁻¹), respectively. The kinetic exponent, n ≈ 1 indicates a surface nucleation mechanism.     

Growth of polar axis oriented tetragonal Pb(Zr,Ti)O3 films on CaF2 substrates with transparent (La0.07Sr0.93)SnO3

Epitaxial (La_0.07Sr_0.93)SnO₃ [LSSO] films were deposited on CaF₂ substrates by pulse laser deposition. The (1 0 0)_c orientation of LSSO films was observed only on (1 1 0)CaF₂, whereas (1 1 0)_c orientation was found on (1 1 1)CaF₂ and (1 0 0)CaF₂. (0 0 1) polar axis oriented tetragonal Pb(Zr_0.35Ti_0.65)O₃ films were grown on the fabricated (1 0 0)_cLSSO∥(1 1 0)CaF₂ by pulsed metal organic chemical vapor deposition. The (0 0 1)Pb(Zr_0.35Ti_0.65)O₃∥(1 0 0)cLSSO∥(1 1 0)CaF₂ stack structure exhibited about 70% transparency with an adsorption edge of approximately 330 nm.     

Non-isothermal crystallization kinetics study on new amorphous Ga20Sb5S75 and Ga20Sb40S40 chalcogenide glasses

Bulk glasses of the system Ga₂₀Sb_xS_80−x (x = 5 and 40) were prepared for the first time by the known melt quenching technique. Non-isothermal differential scanning calorimetric (DSC) measurements of as-quenched Ga₂₀Sb_xS_80−x (x = 5 and 40) chalcogenide glasses reveal that the characteristic temperatures e.g. the glass transition temperature (T_g), the temperature corresponding to the maximum crystallization rate (T_p) recorded in the temperature range 400-650 K for x = 5 and 480-660 K for x = 40 are strongly dependent on heating rate and Sb content. Upon heating, these glasses show a single glass transition temperature (T_g) and double crystallization temperatures (T_p1 and T_p2) for x = 5 which overlapped and appear as a single crystallization peak (T_p) for x = 40. The activation energies of crystallization E_c were evaluated by three different methods. The crystallization data were examined in terms of recent analysis developed for non-isothermal conditions. The crystalline phases resulting from (DSC) have been identified using X-ray diffraction.     

Structural and electrical properties of lead-free perovskite ceramic: Ba(In1/2Nb1/2)O3

Lead-free perovskite Ba(In_1/2Nb_1/2)O₃ was prepared by conventional ceramic fabrication technique at 1350 °C/5 h in air atmosphere. The crystal symmetry, space group and unit cell dimensions were determined from Rietveld analysis using FullProf software whereas crystallite size and lattice strain were estimated from Williamson-Hall approach. XRD analysis of the compound indicated the formation of a single-phase cubic structure with the space group Pm3m. EDAX and SEM studies were carried out in order to evaluate the quality and purity of the compound. Complex impedance as well as electric modulus analyses suggested the dielectric relaxation to be of non-Debye type. The correlated barrier hopping (CBH) model was employed to successfully explain the mechanism of charge transport in Ba(In_1/2Nb_1/2)O₃.     

Structure and growth morphology of Gd2O3-doped CeO2 thin films

Gd₂O₃-doped CeO₂ (Gd_0.1Ce_0.9O_1.95, GDC) thin films were synthesized on (1 0 0) Si single crystal substrates by a reactive radio frequency magnetron sputtering technique. Structures and surface morphologies were characterized by X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and one-dimensional power spectral density (1DPSD) analysis. The XRD patterns indicated that, in the temperature range of 200–700 °C, f.c.c. structured GDC thin films were formed with growth orientations varying with temperature—random growth at 200 °C, (2 2 0) textures at 300–600 °C and (1 1 1) texture at 700 °C. GDC film synthesized at 200 °C had the smoothest surface with roughness of R_rms=0.973 nm. Its 1DPSD plot was characterized with a constant part at the low frequencies and a part at the high frequencies that could be fitted by the f^−2.4 power law decay. Such surface feature and scaling behavior were probably caused by the high deposition rate and random growth in the GDC film at this temperature. At higher temperatures (300–700 °C), however, an intermediate frequency slope (−γ₂≈−2) appeared in the 1DPSD plots between the low frequency constant part and the high frequency part fitted by f⁻⁴ power law decay, which indicated a roughing mechanism dominated by crystallographic orientation growth that caused much rougher surfaces in GDC films (R_rms>4 nm).     

Phase separation and crystallization in the system SiO2-Al2O3-P2O5-B2O3-Na2O glasses

The phase separation and crystallization behavior in the system (80 − X)SiO₂ · X(Al₂O₃ + P₂O₅) · 5B₂O₃ · 15Na₂O (mol%) glasses was investigated. Glasses with X = 20 and 30 phase separated into two phases, one of which is rich in Al₂O₃-P₂O₅-SiO₂ and forms a continuous phase. Glasses containing a larger amount of Al₂O₃-P₂O₅ (X = 40 and 50) readily crystallize and precipitates tridymite type AlPO₄ crystals. It is estimated that the phase separation occurs forming continuous Al₂O₃-P₂O₅-SiO₂ phase at first, and then tridymite type AlPO₄ crystals precipitate and grow in this phase. Highly transparent glass-ceramics comparable to glass can be successfully obtained by controlling heat treatment precisely. The crystal size and percent crystallinity of these transparent glass-ceramics are 20-30 nm and about 50%, respectively.     

Electrical properties of Bi3.15Nd0.85Ti2.8-xZr0.2MnxO12 thin films with different Mn content synthesized by chemical solution deposition (CSD)

Bi_3.15Nd_0.85Ti_2.8-xZr_0.2Mn_xO₁₂ (BNTZM) thin films with various Mn content (x = 0, 0.005, 0.01, 0.03, and 0.05) have been prepared on Pt/Ti/SiO₂/Si (100) substrates by a chemical solution deposition (CSD) technique. The crystal structures of BNTZM thin film have been analyzed by X-ray diffraction (XRD). The dependence of Mn contents on the ferroelectric, dielectric properties, and leakage current of these BNTZM films have been thoroughly investigated. The XRD analysis demonstrated that all the BNTZM thin films were of typical bismuth-layer-structured ferroelectrics (BLSF) polycrystalline structure and exhibited a highly preferred (117) orientation. Among these BNTZM films, the BNTZM thin film with Mn content equal to 0.01 exhibits the maximum remnant polarization (2P_r) of 48μC/cm² and a low coercive field (2E_c) of 177 kV/cm. In addition, the BNTZM thin film with x = 0.01 (Mn) showed a fatigue-free behavior up to 1 × 10¹⁰ read/write cycles.     

Temperature-assisted electrical poling of TeO2-Bi2O3-ZnO glasses for non-linear optical applications

The suitability for effective thermal poling of the ternary tellurite glasses with the compositions (100 − 2x)TeO₂-xBi₂O₃-xZnO (x = 5, 10 and 15, in molar percentage) for the second harmonic generation (SHG) was analyzed. The glass transitions and crystallization temperatures were studied via differential thermal analysis. The structural properties of the annealed glasses and furtherly heat-treated samples were probed by extended X-ray absorption fine structure (EXAFS) spectroscopy. Thermal poling of the glasses was undertaken conventionally at various temperatures close to the glass transition temperature under high vacuum and the second harmonic generated signals were compared. A new technique of two stage poling was tested for comparison. The non-linear second harmonic signal of the poled glasses was analyzed using the Maker-fringe technique and it was found that the two stage poling enhanced the non-linear efficiency when compared to the conventionally poled samples.     

Structural transformation on Se0.8Te0.2 chalcogenide glass

Using X-ray diffraction and differential scanning calorimetry (DSC), the structure and the crystallization mechanism of Se_0.8Te_0.2 chalcogenide glass has been studied. The structure of the crystalline phase has been refined using the Rietveld technique. The crystal structure is hexagonal with lattice parameter a = 0.443 nm and c = 0.511 nm. The average crystallite size obtained using Scherrer equation is equal 16.2 nm, so it lies in the nano-range. From the radial distribution function, the short range order (SRO) of the amorphous phase has been discussed. The structure unit of the SRO is regular tetrahedron with (r₂/r₁) = 1.61. The Se_0.8Te_0.2 glassy sample obeys the chemical order network model, CONM. Some amorphous structural parameters have been deduced. The crystallization mechanism of the amorphous phase is one-dimensional growth. The calculated value of the glass transition activation energy (E_g) and the crystallization activation energy (E_c) are 159.8 ± 0.3 and 104.3 ± 0.51 kJ/mol, respectively.     

Crystallization behavior and microstructure of powdered and bulk ZnO-Al2O3-SiO2 glass-ceramics

The crystallization behavior of glass with the composition: 55.6 mol% SiO₂, 22.8 mol% Al₂O₃, 17.7 mol% ZnO and 3.84 mol% of TiO₂ as nucleating agent and with different particle sizes has been studied by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and tranmission electron microscopy (TEM). In glass powders two crystalline phases: zinc-aluminosilicate s.s. with high-quartz structure, Zn_x/2Al_xSi_3−xO₆, (x varies dependent on heat-treatment temperature) and gahnite are formed. The ratio of these phases depends on particle sizes. In bulk glass, however, gahnite is the sole crystalline phase. The composition of initially formed zinc-aluminosilicate s.s. was determined by Rietveld refinement of XRD patterns to be Zn_0.69Al_1.38Si_1.62O₆. With temperature increase, the amount of zinc-aluminosilicate s.s decreased with simultaneous reduce of zinc and aluminum incorporated in the structure. Eventually at 1423 K almost pure high-quartz structure was formed. The activation energies of zinc-aluminosilicate s.s. and gahnite crystallization were determined by non-isothermal method to be 510 ± 18 and 344 ± 17 kJ mol⁻¹, respectively. The latter value matches well with those cited in literature for crystal growth of gahnite in similar glasses. That is attributed to the fact that the high-quartz structure acts as a precursor for gahnite crystallization.     

Crystallization kinetics of Fe73.5−xMnxCu1Nb3Si13.5B9 (x = 0, 1, 3, 5, 7) amorphous alloys

In this study, we have investigated the effect of substituting Mn for Fe on the crystallization kinetics of amorphous Fe_73.5−xMn_xCu₁Nb₃Si_13.5B₉ (x = 1, 3, 5, 7) alloys. The samples were annealed at 550 °C and 600 °C for 1 h under an argon atmosphere. The X-ray diffraction analyses showed only a crystalline peak belonging to the α-Fe(Si) phase, with the grain size ranging from 12.2 nm for x = 0 to 16.7 nm for x = 7. The activation energies of the alloys were calculated using Kissinger, Ozawa and Augis-Bennett models based on differential thermal analysis data. The Avrami exponent n was calculated from the Johnson-Mehl-Avrami equation. The activation energy increased up to x = 3, then decreased with increasing Mn content. The values of the Avrami exponent showed that the crystallization is typical diffusion-controlled three-dimensional growth at a constant nucleation rate.     

Thermal, chemical, optical properties and structure of Er-doped and Er/Yb-codoped P2O5-Al2O3-ZnO glasses

This study was explored in series of the optical, thermal, and structure properties based on 60P₂O₅-10Al₂O₃-30ZnO (PAZ) glasses system that doped with varied rare-earth (RE) elements Yb₂O₃/Er₂O₃. The glass transition temperature, softening temperature and chemical durability were increased with RE-doping concentrations increasing, whereas thermal expansion coefficient was decreased. In the optical properties, the absorption and emission intensities also increase with RE-doping concentrations increasing, When Er₂O₃ and Yb₂O₃ concentrations are over than 3 mol% in the Er³⁺-doped PAZ system and Yb³⁺-doped concentration is over than 3 mol% for Er³⁺/Yb³⁺-codoped PAZ system, the emission intensity significantly decreases presumably due to concentration quenching, formation of the ions clustering, and OH⁻ groups in the glasses network. It is suggested that the maximum emission cross-section (σ_e) is 7.64 × 10^− 21 cm² at 1535 nm is observed for 3 mol% Er³⁺-doped PAZ glasses. Moreover, the maximum σ_e × full-width-at-half-maximum is 327.8 for 5 mol% Er³⁺-doped PAZ glasses.     

Structure and properties of Ni60(Nb100−xTax)34Sn6 bulk metallic glass alloys

Refractory bulk metallic glasses and bulk metallic glass composites are formed in quaternary Ni-Nb-Ta-Sn alloy system. Alloys of composition Ni₆₀(Nb_100−xTa_x)₃₄Sn₆ (x = 20, 40, 60, 80) alloys were prepared by injection-casting the molten alloys into copper molds. Glassy alloys are formed in the thickness of half mm strips. With thicker strips (e.g., 1 mm), Nb₂O₅ and Ni₃Sn phases and the amorphous phase form an in situ composite. Glass transition temperatures, crystallization temperatures, and ΔT_x, defined as T_x1 − T_g (T_x1: first crystallization temperature, T_g: glass transition temperature) of the alloys increase dramatically with increasing Ta contents. These refractory bulk amorphous alloys exhibit high Young’s modulus (155-170 GPa), shear modulus (56-63 GPa), and estimated yield strength (3-3.6 GPa).     

Laser-induced crystallization of β′-RE2(MoO4)3 ferroelectrics (RE: Sm, Gd, Dy) in glasses and their surface morphologies

The glasses with the compositions of 21.25RE₂O₃-63.75MoO₃-15B₂O₃ (RE: Sm, Gd, Dy) were prepared and the formation of β′-RE₂(MoO₄)₃ ferroelectrics was confirmed in the crystallized glasses obtained through a conventional crystallization in an electric furnace. The features of the glass structure and crystallization behavior were clarified from measurements of Raman scattering spectra. Continuous-wave Nd:YAG laser with a wavelength of 1064 nm (laser power: 0.6-0.9 W, laser scanning speed: S = 1-16 μm/s) was irradiated to 10.625Sm₂O₃-10.625Gd₂O₃ (or Dy₂O₃)-63.75MoO₃-15B₂O₃ glasses, and the structural modification was induced at the glass surface. At the scanning speed of S = 10 μm/s, crystal lines consisting of β′-Gd_2−xSm_x(MoO₄)₃ or β′-Dy_2−xSm_x(MoO₄)₃ crystals were patterned on the glass surface. It was found that those crystal lines have the surface morphology with periodic bumps. At S = 1 μm/s, it was found that crystal lines consist of the mixture of paraelectric α-Gd_2−xSm_x(MoO₄)₃ and ferroelectric β′-Gd_2−xSm_x(MoO₄)₃ crystals, indicating the phase transformation from the β′ phase to the α phase during laser irradiation. Homogeneous crystal lines with β′-RE₂(MoO₄)₃ ferroelectrics have not been written in this study, but further research is continuing.     

Bioactive glasses in the system CaO-B2O3-P2O5: Preparation, structural study and in vitro evaluation

Glasses in the system x B₂O₃(1 − x) [y CaO P₂O₅], (x = 0, 0.1, 0.2, 0.3, y = 2, 2.6, 3, 4, 5) have been prepared by fast quenching of high temperature melts. The presence of B₂O₃ affected the glass forming ability, allowing the preparation of calcium phosphate glasses with y ? 2.6. The structure of glasses was analyzed by μ-Raman and infrared spectroscopy. The analysis indicated that the glass network is dominated by highly charged species from phosphate tetrahedra with 3 (pyro) or 4 (ortho) NBOs, while the boron atoms are incorporated mainly in 3 coordinated sites in the form of B∅₃ or B∅₂O⁻ units. A small fraction of units was also evident from the spectra analysis of glasses with high CaO content. All calcium borophosphate glasses exhibited bioactivity after soaking in SBF solution within a few days. This was observed by μ-Raman and SEM microscopy, while XRD patterns clearly revealed growth of hydroxyapatite phase. The presence of boron in the glass network has a catalytic effect at favoring bioactivity of the otherwise bioinert calcium phosphate glasses.