Platinum solubility of a substance designed as a model for emissions of automobile catalytic converters

Automobile catalytic converters emit nanocrystalline platinum attached to alumina particles. For investigations about the bioavailability of Pt from these particles a model substance with approx. 5% Pt on alumina has been prepared and characterized by physical methods (ESCA, XRD, TEM, DTA, TG). Measuring the platinum solubility of these samples in different solvents revealed high amounts that can be explained assuming a corrosion process. The portion of soluble platinum is dependent on the particle size distribution. For a comparative study platinum black has been used. In general the platinum determination has been carried out by electrothermal atomic absorption spectrometry (ET-AAS). The comparison of ET-AAS results with determinations by adsorptive voltammetry (formazone method) allowed to distinguish between elemental and ionic platinum; in solution samples only ionic platinum has been present. UV spectra of extracts have been used for the semi-quantitative platinum speciation in solutions.     

甲基环戊烷在铂催化剂上氢解的动力学研究

研究了甲基环戊烷在负载型铂催化剂上的氢解动力学，建立了新的动力学模型，在Ｐｔ／ＳｉＯ２上，两个平行反应（一个生成正己烷，另一个生成甲基戊烷）在甲基环戊烷吸附脱氢过程中存在显著的焓变差异，而Ｃ－Ｃ键断裂活化能则相近，在Ａｌ２Ｏ３负载铂催化剂上，反应的表现活经能仅是在Ｐｔ／ＳｉＯ２上的一半，这是由于Ｃｌ离子的存在，改变了铂的催化性能，导致缺电子铂颗粒的形成，使反应速率的控制步骤从在Ｐｔ／ＳｉＯ２上的Ｃ     

X-ray photoelectron study of the interaction of H<Subscript>2</Subscript> and H<Subscript>2</Subscript>+O<Subscript>2</Subscript> mixtures on the Pt/MoO<Subscript>3</Subscript> model catalyst

The effects of H₂ and H₂ + O₂ gas mixtures of varying composition on the state of the surface of the Pt/MoO₃ model catalyst prepared by vacuum deposition of platinum on oxidized molybdenum foil were investigated by X-ray photoelectron spectroscopy (XPS) at room temperature and a pressure of 5–150 Torr. For samples with a large Pt/Mo ratio, the XP spectrum of large platinum particles showed that the effect of hydrogen-containing mixtures on the catalyst was accompanied by the reduction of molybdenum oxide. This effect results from the activation of molecular hydrogen due to the dissociation on platinum particles and subsequent spill-over of hydrogen atoms on the support. The effect was not observed at low platinum contents in the model catalyst (i.e., for small Pt particles). It is assumed for the catalyst that the loss of its hydrogen-activating ability is a consequence of the formation of platinum hydride. Possible participation of platinum hydride as intermediate in hydrogen oxidation to H₂O₂ is discussed.     

Probing platinum degradation in polymer electrolyte membrane fuel cells by synchrotron X-ray microscopy

Synchrotron-based scanning transmission X-ray spectromicroscopy (STXM) was used to characterize the local chemical environment at and around the platinum particles in the membrane (PTIM) which form in operationally tested (end-of-life, EOL) catalyst coated membranes (CCMs) of polymer electrolyte membrane fuel cells (PEM-FC). The band of metallic Pt particles in operationally tested CCM membranes was imaged using transmission electron microscopy (TEM). The cathode catalyst layer in the beginning-of-life (BOL) CCMs was fabricated using commercially available catalysts created from Pt precursors with and without nitrogen containing ligands. The surface composition of these catalyst powders was measured by X-ray Photoelectron Spectroscopy (XPS). The local chemical environment of the PTIM in EOL CCMs was found to be directly related to the Pt precursor used in CCM fabrication. STXM chemical mapping at the N 1s edge revealed a characteristic spectrum at and around the dendritic Pt particles in CCMs fabricated with nitrogen containing Pt-precursors. This N 1s spectrum was identical to that of the cathode and different from the membrane. For CCM samples fabricated without nitrogen containing Pt-precursors the N 1s spectrum at the Pt particles was indistinguishable from that of the adjacent membrane. We interpret these observations to indicate that nitrogenous ligands in the nitrogen containing precursors, or decomposition product(s) from that source, are transported together with the dissolved Pt from the cathode into the membrane as a result of the catalyst degradation process. This places constraints on possible mechanisms for the PTIM band formation process.     

Nanoscale Pt(0) particles prepared in imidazolium room temperature ionic liquids: synthesis from an organometallic precursor,characterization, and catalytic properties in hydrogenation reactions

The reaction of Pt(2)(dba)(3) (dba = bis-dibenzylidene acetone) dispersed in room temperature 1-n-butyl-3-methylimidazolium (BMI) hexafluorophosphate ionic liquid with molecular hydrogen (4 atm) at 75 degrees C leads to stable and isolable nanometric Pt(0) particles. The X-ray diffraction analysis (XRD) of the material indicated that it is constituted of Pt(0). Transmission electron microscopy (TEM) analysis of the particles dispersed in the ionic liquid shows the formation of [Pt(0)](n) nanoparticles of 2.0-2.5 nm in diameter. A detailed examination of the nanoparticles imbibed in the ionic liquid and their environment shows an interaction of the BMI.PF(6) ionic liquid with the Pt(0) nanoparticles. The isolated [Pt(0)](n) nanoparticles can be redispersed in the ionic liquid or in acetone or used in solventless conditions for liquid-liquid biphasic, homogeneous, or heterogeneous hydrogenation of alkenes and arenes under mild reaction conditions (75 degrees C and 4 atm). The recovered platinum nanoparticles can be reused as a solid or redispersed in the ionic liquid several times without any significant loss in catalytic activity.     

An XPS and STM Study of Oxidized Platinum Particles Formed by the Interaction between Pt/HOPG with NO<Subscript>2</Subscript>

X-ray photoelectron spectroscopy (XPS) (with AlK_α and AgL_α radiations) and scanning tunneling microscopy (STM) were used to study the interaction of two model samples prepared by vacuum evaporation of platinum on highly oriented pyrolytic graphite (HOPG) with NO₂ at room temperature. According to STM data, platinum evaporation on the graphite surface produced particles of a flattened shape. In the Pt/HOPGS1 sample with a lower concentration of platinum, the average diameter of particles d and the height-to-diameter ratio h/d were 2.8 nm and 0.29, respectively. In the Pt/HOPG-S2 sample with a higher concentration of platinum, the average values of d and h/d were 5.1 nm and 0.32. When the samples interacted with NO₂ (P ≈ 3 × 10^–6 mbar), the particles of metallic platinum completely converted to the particles of PtO_2· Upon oxidation, the shape of larger platinum particles in the Pt/HOPG-S2 sample did not change, although for the dispersed particles in the Pt/HOPG-S1 samples under these conditions, the h/d ratio increases. The reduction of oxide to metal particles on heating the Pt/HOPG-S1 sample in vacuum at 460°С is accompanied by an increase in the size of particles. Their shape became more round compared to the initial one. It was found that X-ray radiation affects the state of platinum in the oxidized sample by reducing the surface layer of PtO₂ to PtO.     

EuroPt-1 catalyst: Radial distribution of electron density X-ray diffraction and EXAFS studies

The supported Pt/SiO₂ (EuroPt-1) catalyst has been studied by the radial distribution of electron density (RDED) and EXAFS techniques. The starting sample of the catalyst was stored in air, not subjected to any further treatment, and contained metal platinum Pt⁰ and platinum oxide PtO in a ～1:2 ratio. An analysis of the EXAFS data was based on three possible structural models of platinum particles. Model 1 suggested that there was one Pt-Pt short contact, which was the same in the bulk of the particles and on the surface. Model 2 considered two different Pt-Pt distances for the particle volume and surface. For model 3, we additionally assumed that the corresponding Debye-Waller factors differed. For the oxidized sample, model 2 was most reliable, and the Pt-Pt distance between the surface atoms was shortened by ～0.14 Å. For the reduced samples, the structural data obtained are consistent with model 3.     

Effect of support and loading on oxidation of methane over platinum catalysts

Catalytic combustion of methane was carried out using platinum catalysts supported on low-and high-surface area alumina (denoted respectively as LSA and HSA) and platinum supported on silica. Methane conversion was the highest for platinum supported on LSA alumina, smaller for Pt/HSA alumina and the smallest for Pt/silica. However, the 3 wt.% Pt/HSA catalyst was found to show the highest selectivity.     

selective catalytic reduction of nitrogen oxides over Cu-TS-1/cordierite and LaCu-TS-1/cordierite

Summary A catalytic system was obtained by impregnation with platinum of thin alumina films electrochemically deposited on stainless steel. The composition, morphology and structure of the Pt/Al2O3/SS and Pt/CeO2/Al2O3/SS samples were characterized by XPS, SEM and BET. Catalytic tests of the samples were performed in a stoichiometric gas mixture.     

Formic acid electro-synthesis from carbon dioxide in a room temperature ionic liquid

The novel synthesis of formic acid has been achieved in a room temperature ionic liquid via the reaction of electro-activated carbon dioxide and protons on pre-anodised platinum. Only mild reaction conditions of room temperature and 1 atm CO(2) were used. This work highlights the effect of pre-anodisation on Pt surfaces.     

Formation mechanism of Pt particles by photoreduction of Pt ions in polymer solutions

The formation mechanisms of metal particles (platinum (Pt) particles) in an aqueous ethanol solution of poly(N-vinyl-2-pyrrolidone) (PVP) by the photoreduction method have been studied by transmission electron microscopy (TEM) and in situ and ex situ X-ray absorption fine structure (XAFS) analysis. The average diameter of the dilute and concentrated Pt particles in the PVP solution is estimated from TEM to be 2.0 and 2.5 nm, respectively. XAFS analysis was performed for the reduction process of Pt4+ ions to metallic Pt particles for the Pt L3 edge of the colloidal dispersions of the concentrated Pt solutions. The photoreduction process proceeds by the following steps: (1) reduction of PtCl6(2-) to PtCl4(2-), (2) dissociation of Cl from PtCl4(2-), followed by reduction of Pt2+ ionic species to Pt0, (3) formation of a Pt0-Pt0 bond and particle growth by the association of Pt0-Pt0. The reduction of PtCl4(2-) to Pt0 is a slower process, compared with the reduction of PtCl6(2-) to PtCl4(2-). There is a delay between the disappearance of PtCl4(2-) and the formation of Pt0-Pt0 clusters.     

Characterization and reactivity of Pt/Al2O3/SS thin films

Summary A catalytic system was obtained by impregnation with platinum of thin alumina films electrochemically deposited on stainless steel. The composition, morphology and structure of the Pt/Al2O3/SS and Pt/CeO2/Al2O3/SS samples were characterized by XPS, SEM and BET. Catalytic tests of the samples were performed in a stoichiometric gas mixture.     

Speciation of Cr(III) and Cr(VI) in potable waters by using activated neutral alumina as collector and ET-AAS for determination

The speciation of Cr(III) and Cr(VI) has been performed by using activated neutral alumina as adsorbent. Both species were quantitatively adsorbed on a small column filled with neutral alumina. The adsorbed Cr(III) was eluted with 4 mol L(-1) HNO(3) and Cr(VI) with 1.0 mol L(-1) ammonia solution. Recoveries of Cr(III) and Cr(VI) were 99% and 100%, respectively. Using ET-AAS for Cr determination the limit of detection in the sample was 0.01 microg L(-1). The combined procedure is fast and sensitive. It can be applied for routine analysis of water samples at sub-microg L(-1) levels with a relative standard deviation (RSD) of 2-10% (three determinations).     

Synthesis and characterization of Pt0 nanoparticles in imidazolium ionic liquids

The controlled decomposition of Pt2(dba)3 (dba = dibenzylideneacetone) dispersed in 1-n-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF4) and hexafluorophosphate (BMI.PF6) ionic liquids in the presence of cyclohexene by molecular hydrogen produces Pt0 nanoparticles. The formation of these nanoparticles follows the two-step [A --> B, A + B --> 2B (k1, k2)] autocatalytic mechanism. The catalytic activity in the hydrogenation of cyclohexene is influenced by the nature of the anion rather than the mean-diameter of the nanoparticles. Thus, higher catalytic activity was obtained with Pt0 dispersed in BMI.BF4 containing the less coordinating anion although these nanoparticles possess a larger mean diameter (3.4 nm) than those obtained in BMI.PF6 (2.3 nm). Similar mean diameter values were estimated from in situ XRD and SAXS. XPS analyses clearly show the interactions of the ionic liquid with the metal surface demonstrating the formation of an ionic liquid protective layer surrounding the platinum nanoparticles. SAXS analysis indicated the formation of a semi-organized ionic liquid layer surrounding the metal particles with an extended molecular length of around 2.8 nm in BMI.BF4 and 3.3 nm in BMI.PF6.     

Structure and catalytic properties of nanosized alumina supported platinum and palladium particles synthesized by reaction in microemulsion

Mixtures of nanosized platinum and palladium particles have been prepared by reduction of salt-containing microemulsion droplets using hydrazine as the reducing agent. To avoid possible negative effects of the presence of sulfur compounds during the preparation the microemulsion was made using the sulfur-free nonionic polyoxyethylene 4 lauryl ether surfactant. Transmission electron microscopy showed that the as-prepared mixtures contained crystalline platinum particles of fairly homogeneous size (20 to 40 nm) with adsorbed amorphous palladium particles 2 to 5 nm in size. Catalyst samples were prepared by depositing the nanoparticles on a gamma-Al(2)O(3) support followed by heating in air at 600 degrees C. Alloyed particles of platinum and palladium with sizes ranging from 5 to 80 nm were obtained during the heating. The majority of the particles had the fcc structure and their compositional range was dependent upon the Pt:Pd molar ratio of the microemulsion. A catalyst prepared from a microemulsion with a 20:80 Pt:Pd molar ratio showed the highest catalytic activity for CO oxidation, while pure platinum and palladium catalysts showed higher sulfur resistance. These results differ from the performance of conventional wet-impregnated catalysts, where a 50:50 Pt:Pd molar ratio resulted in the highest catalytic activity as well as the highest sulfur resistance.     

Growth of a Pt film on non-reduced ceria: a density functional theory study

The growth of platinum on non-reduced CeO(2) (111) surface is studied by means of calculations based on the density functional theory. Particles of increasing size are formed on the oxide surface by incorporating the platinum atoms one by one until multilayer films are obtained. The main conclusion is that platinum atoms tend to maximize the number of metallic bonds and to approach the situation of the bulk, hence preferring films to particles, particles to isolated atoms, and a three-dimensional growth to a two-dimensional one. The supported particles and the films exhibit a contraction of the Pt-Pt distances, with respect to those of the Pt bulk, in order to match the ceria lattice. The density of states projected on the film surface platinum atoms shows important differences in shape and energy (lower d-band center) compared to the Pt(111) reference surface, which could be the major reason for the observed changes in catalytic reactivity when deposited particles are compared with single crystal surfaces.     

Deep Oxidation of Methane on a Pt/Si3N4 Catalyst

We have studied platinum catalysts supported on silicon nitride Si₃N₄ in the process of deep oxidation of methane. We have used transmission electron microscopy and X-ray photoelectron spectroscopy to study the surface properties of the Pt/Si₃N₄ samples before and after the catalytic reaction. We have established that the metallic platinum particles in freshly prepared systems are characterized by average sizes of 1.7-5.3 nm, while after the catalytic reaction we observe formation of Pt crystallites up to 30-70 nm in size. We hypothesize that the observed deactivation of platinum catalysts in deep oxidation of methane is connected with crystallization of the metallic particles and their entrainment with the reaction products during catalysis.     

Size-controlled synthesis of colloidal platinum nanoparticles and their activity for the electrocatalytic oxidation of carbon monoxide

Using polyvinylpyrrolidone (PVP) as a stabilizing agent, stable colloidal solutions of platinum nanoparticles of different size distributions have been prepared by reducing H2PtCl6 with hydrogen. The UV-vis adsorption peaks at 258 nm due to the adsorption of Pt(IV) species disappear completely, indicating that the Pt(IV) species has been used up and colloidal Pt has been formed. The electrodes have been prepared from aqueous Pt colloids and glassy carbon (GC). The effect of platinum particle size of Pt/GC catalyst electrode on the electrocatalytic oxidation of carbon monoxide has been investigated. The voltammetry shows that a higher potential is needed for the oxidation of absorbed carbon monoxide with a decrease of the platinum particle size for particle sizes larger than 1 nm. But for particle sizes smaller than 1 nm, the potential remains constant while the activity decreases with decreasing the size. The snowlike, well-dispersed, and highly ordered platinum nanoparticles demonstrate high activity in the oxidation reaction of carbon monoxide. The reason may be due to the geometric structure of platinum nanoparticles.     

Alumina interaction with AMPS-MPEG random copolymers I. Adsorption and electrokinetic behavior

Adsorption of brush copolymers, bearing sulfonate groups and polyethylene glycol segments, on to alumina particles in suspension in water has been investigated. Study of the adsorption isotherms revealed that the copolymers displayed a strong affinity for the surface of the alumina regardless of the fraction of ionic groups on the polymer. For poly(ethylene glycol) content greater than 50%, the adsorption isotherms revealed an initial adsorption plateau followed by a second one. The shape of the adsorption isotherms was interpreted in terms of the polymer configuration at the solid-to-liquid interface. The effects of the pH and the ionic force on adsorption were studied and connected to the effects of interaction between chain segments at the surface of the alumina particles. Changes in the electrokinetic properties of the alumina particles after addition of the copolymers were investigated by following the zeta potential of particles as a function of pH. In the presence of the copolymer continuous shift of the isoelectric point IEP to a more acidic values was observed. Beyond a certain concentration the zeta potential remained negative regardless of the pH.     

Fabrication of double-walled carbon nanotube counter electrodes for dye-sensitized solar sells

Double-walled carbon nanotubes (DWCNTs) have been studied for counter-electrode application in dye-sensitized solar cells (DSCs). Mesoporous TiO2 films are prepared from the commercial TiO2 nanopowders by screen-printing technique on optically transparent-conducting glasses. A metal-free organic dye (indoline dye D102) is used as a sensitizer. DWCNTs are applied to substitute for platinum as counter-electrode materials. Morphological and electrochemical properties of the formed counter electrodes are investigated by scanning electronic microscopy and electrochemical impedance spectroscopy, respectively. The electronic and ionic processes in platinum and DWCNT-based DSCs are analyzed and discussed. The catalytic activity and DSC performance of DWCNTs and Pt are compared. A conversion efficiency of 6.07% has been obtained for DWCNT counter-electrode DSCs. This efficiency is comparable to that of platinum counter-electrode-based devices.