Uniaxial tensile tests and dynamic mechanical analysis of satin weave reinforced epoxy shape memory polymer composite

The utilization of epoxy shape memory polymer composite (SMPCs) as engineering materials for deployable structures has attracted considerable attention in recent decades due to high strength and satisfactory stiffness in comparison with shape memory polymers (SMPs). Knowledge of static and dynamic mechanical properties is essential for analyzing structural behavior and recovery properties, especially for new epoxy SMPCs. In this paper, a new weave reinforced epoxy shape memory polymer composite was prepared with satin weave technique and resin transfer molding technique. Uniaxial tensile tests and dynamic mechanical analysis were carried out to obtain basic mechanical properties and glass transition temperatures, respectively.The tensile strength and breaking elongation of warp specimens were comparable with those of weft specimens. The increment of elastic modulus and hysteresis loop areas became smaller with loading cycles, meaning that cyclic tests could obtain approximate stable mechanical properties. For dynamic mechanical properties, glass transition temperature (T_g) obtained from storage modulus curves was lower than that determined from tan delta curves and T_gs in the warp and weft directions were similar (29.4 °C vs 29.7 °C). Moreover, the storage modulus in response to T_g was two orders of magnitude less than that with respect to low temperature, which demonstrated the easy processibility of epoxy SMPCs near glass transition temperature. In general, this study could provide useful observations and basic mechanical properties of new epoxy SMPCs.     

Glutaraldehyde treatment of bacterial cellulose/fibrin composites: impact on morphology, tensile and viscoelastic properties

Bacterial cellulose/fibrin composites were treated with glutaraldehyde in order to crosslink the polymers and allow better match of the mechanical properties with those of native small-diameter blood vessels. Tensile and viscoelastic properties of the glutaraldehyde treated composites were determined from tensile static tests and cyclic creep tests, respectively. Glutaraldehyde-treated (bacterial cellulose) BC/fibrin composites exhibited tensile strength and modulus comparable to a reference small-diameter blood vessel; namely a bovine coronary artery. However, the breaking strain of the glutaraldehyde-treated composites was still well below that of the native blood vessel. Yet a long strain hardening plateau was induced by glutaraldehyde treatment which resembled the stress–strain response of the native blood vessel. Tensile cyclic creep test indicated that the time-dependent viscoelastic behavior of glutaraldehyde-treated BC/fibrin composites was comparable to that of the native blood vessel. Covalent bonding between BC and fibrin occurred via glutaraldehyde, affording mechanical properties comparable to that of the native small blood vessel.     

振动注塑PP的拉伸蠕变研究

分别通过改变机械振动注塑机的频率(5~25 Hz)和压力(10~18 MPa)获得不同条件下成型的PP样条,然后在各种成型条件下的PP样条上分别施加相同的拉伸力(F=125 N),进行24 h拉伸蠕变实验.结果表明,在相同的振动频率(10 Hz)和不同的振动压力下成型的PP试样,其24 h蠕变量随着压力的增大而减小;在相同振动压力(12 MPa)和不同的振动频率下成型的PP试样,其24 h蠕变量随着频率的增大而增大.当振动频率达到f=10 Hz的时候,其24 h拉伸蠕变量的变化趋于平缓.同时,也对不同振动条件下注塑的PP试样进行拉伸实验,冲击实验和动态力学性能测试,讨论了成型条件对性能的影响.     

Mechanical and shape memory performance of shape memory polyurethane-based aligned nanofibers

In recent years, shape memory polyurethane (SMPU) as a smart material has been used in various applications owing to its desirable shape memory effect and biocompatibility. In this study, unidirectional SMPU nanofibers are innovated by electrospinning to clarify the mechanical and shape memory properties with nanofiber directions. The results showed that when the nanofiber alignment degree is 0° (parallel to the tensile direction), the aligned SMPU nanofibers achieved the obvious improvement of tensile strength (increased to 135%) and elastic modulus (increased to 313%), compared with the random SMPU nanofiber. Moreover, the developed aligned nanofibers exhibited good ability against stress relaxation and creep under constant strain or constant stress conditions in cyclic loading. The aligned SMPU nanofibers with a 0° alignment degree exhibited excellent shape memory properties with shape recovery rates larger than 93% and shape fixity rates larger than 90%, and a dramatic increase of shape recovery stress.     

Epoxy shape memory polymer (SMP): Material preparation,uniaxial tensile tests and dynamic mechanical analysis

The utilization of epoxy shape memory polymers (SMPs) as engineering materials for deployable structures has attracted considerable attention due to their excellent thermo-mechanical endurance and satisfactory processability. Knowledge of static and dynamic mechanical properties is essential for analyzing structural behavior and recovery, especially for new epoxy SMPs. In this paper, a new epoxy SMP was prepared with epoxy and aromatic amine curing agent. Uniaxial tensile tests and digital image correlation were used to obtain static mechanical properties. Dynamic mechanical analysis was carried out to evaluate glass transition temperatures that corresponded to the heat in the recovery process.It was found that elastic modulus, Poisson’s ratio and shear modulus are 1413 MPa, 0.35 and 591 MPa, respectively. The beginning of glass transition temperature of 37.4 °C could be effectively achieved by electrical heaters, validating the shape memory properties of epoxy SMPs. In general, this study could provide useful observations and basic mechanical properties of epoxy SMPs.     

Effects of temperature and stress on creep properties of ethylene tetrafluoroethylene (ETFE) foils for transparent buildings

Creep properties of ethylene tetrafluoroethylene (ETFE) foils are indispensable for evaluating serviceability limit state, especially under high temperature and high stress. This paper concerned temperature and stress effects on creep properties of ETFE foils with experimental and theoretical studies. Experimental results showed that dimensionless stress effect on creep properties could be higher than that of temperature effect. A unified equation incorporating temperature, stress and time based on experimental results was determined and could be utilized to calculate the stress limits and long-term creep strains. The stress limits in response to creep strain of 10% were less than 5 MPa, 4 MPa and 3 MPa for temperature ranges of 40–50 °C, 50–60 °C and 70–80 °C, respectively. The long-term creep strain of ETFE foils under 40 °C was 5.96% concerning 50-year working time.Master curves of ETFE foils were evaluated considering time-temperature superposition (TTSP) and time-stress superposition (TSSP). Long-term creep strains with these master curves were identified and compared with experimental creep strains. It is found that TTSP could be a little underestimation of creep strains while TSSP could overestimate creep strains to some extent. Moreover, the maximum creep strain difference was only 0.48%, which justified the feasibility and suitability of using the unified equation to predict creep strains of ETFE foils.     

Influence of plasticizers and crosslinking on the properties of biodegradable films made from sodium caseinate

Plasticized protein films were prepared by the casting method from water solution of sodium caseinate and plasticizers with the aim to obtain environmentally friendly materials for packaging applications. Mechanical properties (tensile strength, elongation and Young’s modulus) of caseinate based films were determined versus ratio of protein to plasticizer, plasticizer type and relative humidity conditions. Among the different polyol-type plasticizers tested, glycerol (Gly) and triethanolamine (TEA) were the most efficient for the improvement of mechanical properties (high strains for low stresses). Further, chemical crosslinking between formaldehyde (HCHO) and free amino groups (ε-NH₂) of sodium caseinate was performed to increase water resistance of TEA plasticized films. Optimal mechanical properties, i.e. elastic modulus of 105 MPa, tensile strength of 8-9 MPa for elongation at break about 110-125% were obtained for HCHO/ε-NH₂ ratios higher than 1.35. Protein specific water solubility was determined from a 280 nm absorbance. For convenient crosslinker (HCHO) content sodium caseinate solubility can be lowered to less than 5 wt% after 24 h immersion in water.     

Deformation behavior and mechanical properties of hard elastic and porous films of polyethylene

Hard elastic samples of linear polyethylene were prepared by melt extrusion at a high velocity of the melt flow and by subsequent annealing of crystallized samples. The deformation behavior of hard elastic samples obtained by annealing of as-spun samples at different temperatures has been analyzed at uniaxial extension resulting in formation of porous structure. Mechanical properties of microporous films in the longitudinal and transverse directions have been investigated. Composite systems consisting of a microporous polyethylene film and a thin layer of an electroconducting polymer have been prepared. Mechanical properties of composite systems, such as elastic modulus, tensile strength, and break elongation, have been compared with the properties of polyethylene substrates.     

Cyclic stress–strain behavior of the dry polycarbonate craze

Equipment and methods have been developed which allow photomicrographic determination of the stress–strain properties of the individual craze. Serial cyclic tensile tests on polycarbonate crazes are described. Under stress the typical dry polycarbonate craze thickens solely by straining; no adjacent polymer of normal density is converted to craze material. The craze exhibits a yield stress followed by a recoverable flow to roughly 40–50% strain at 6000–8000 psi. On return to zero stress the craze exhibits creep recovery at a decelerating rate. The yield stress and loss factor of each cycle decrease with increasing initial strain and cycles initiating at 50% strain or more show completely Hookean behavior. Creep recovery results in recovery of yield stress and loss factor also. Craze tensile behavior is suggested to be essentially an extension of the craze formation process. Decrease in elastic modulus and yield stress with increasing strain are rationalized in terms of strain-produced decrease in density and resultant increase in stress concentration factor on the microscopic polymer elements of the craze. Polymer surface tension and the large internal specific surface area of the craze are suggested to be important factors in the large creep recovery rates of the craze.     

Nanoindentation creep of nonlinear viscoelastic polypropylene

Uniaxial tensile creep tests at various applied stresses were carried out to demonstrate that PP is nonlinear viscoelastic. A novel phenomenological model consisting of springs, dashpots, stress-locks and sliders was proposed to describe the nonlinear viscoelasticity. Indentation creep tests at different applied load levels were also performed on nonlinear viscoelastic PP. It was found that the shear creep compliance varies with the applied load level when the applied load is less than 5 mN, which means the indentation creep behavior was nonlinear. To find the real reason for the nonlinearity in indentation creep tests, the elastic modulus at various indentation depths was measured using continuous stiffness measurements (CSM). By analyzing the variation of elastic modulus with indentation depth, the nonlinearity of indentation creep behavior was proved to be caused by the non-uniform properties in the surface of the specimen rather than nonlinear viscoelasticity.     

Fading memory of deformation history in carbon black-filled thermoplastic elastomers

Observations are reported on a carbon black–reinforced thermoplastic elastomer in multistep uniaxial tensile cyclic tests with a mixed deformation program (oscillations between maximum elongation ratios k_max and various minimum stresses σ_min with k_max monotonically increasing with number of cycles n). Fading memory of deformation history is demonstrated: when specimens are subjected to two loading programs that differ along the first n −1 cycles of deformation and coincide afterwards, their stress–strain diagrams become identical starting from the nth cycle. A constitutive model is developed in cyclic viscoplasticity with finite deformations, and its adjustable parameters are found by fitting the observations. Ability of the stress–strain relations to describe the fading memory phenomenon and to predict the mechanical response of polymer composites in multi-step cyclic tests with large strains is confirmed by numerical simulation.     

A novel orientation technique for semi-rigid polymers. 2. Mechanical properties of cellulose acetate and hydroxypropylcellulose films

The networks of cellulose acetate and hydroxypropylcellulose prepared in the first part of this investigation were studied with regard to their mechanical properties. The quantities of particular interest were increases in tensile modulus and tensile strength obtained by drying the swollen films under strain, both uniaxial and equi-biaxial. These increases or improvements in mechanical properties were determined as a function of polymer concentration during cross-linking, polymer molecular weight, degree of cross-linking, and elongation during drying. In all cases, the improvements increased with increase in elongation during drying, and the largest increases were obtained in the case of the highest molecular weight polymer which had been lightly cross-linked in dilute (isotropic) solutions. The extent of ordering in these systems was gauged approximately by measurements of birefringence, which were correlated with their tensile moduli and tensile strengths.     

Influence of high loading of cellulose nanocrystals in polyacrylonitrile composite films

Polyacrylonitrile-co-methacrylic acid (PAN-co-MAA) and cellulose nanocrystal (CNC) composite films were produced with up to 40 wt% CNC loading through the solution casting method. The rheological properties of the solution/suspensions and the structural, optical, thermal, and mechanical properties of the resulting films were investigated. The viscosity of the composite suspensions increased with higher CNC loadings and with longer aging times. PAN-co-MAA/CNC films maintained a similar level of optical transparency even with up to 40 wt% CNC loading. The glass transition temperature (Tg) increased from 92 to 118 °C, and the composites had higher thermal stability below 350 °C compared to both neat PAN-co-MAA and neat CNC. The mechanical properties also increased with higher CNC loadings, elastic modulus increased from 2.2 to 3.7 GPa, tensile strength increased from 75 to 132 MPa, and the storage modulus increased from 3.9 to 10.5 GPa. Using the Kelly and Tyson model the interfacial shear strength between the PAN-co-MAA and CNC was calculated to be 27 MPa.     

Quantitative assessment of deformation-induced damage in polyethylene pressure pipe

This paper presents results from a study that quantifies the influence of excessive deformation on the damage development in polyethylene (PE) pressure pipe. The experimental investigation is through the application of a novel two-stage approach to the D-split test of notched pipe ring (NPR) specimens. The first test is to introduce damage by subjecting the specimens to different levels of tensile strain at crosshead speeds of 0.01, 1, 10 or 100 mm/min. The second test is to apply monotonic tensile loading at a crosshead speed of 0.01 mm/min to characterize the mechanical properties for specimens that have had damage generated in the first test. Experimental results suggest that elastic modulus and yield stress decrease and yield strain increases with increase of the strain introduced in the first test. Variation of experimentally measured elastic modulus is used to establish influence of crosshead speed on the damage evolution in the PE pressure pipe.     

New soybean oil‐styrene‐divinylbenzene thermosetting copolymers. III. Tensile stress–strain behavior

The tensile stress–strain behavior and fracture properties of some new soybean oil based polymeric materials were investigated at room temperature. These materials were prepared by the cationic copolymerization of regular soybean oil, low saturation soybean oil (LoSatSoy oil), or conjugated LoSatSoy oil with styrene and the diene comonomers divinylbenzene, norbornadiene, or dicyclopentadiene in a process initiated by boron trifluoride diethyl etherate (BF₃ · OEt₂) or related modified initiators. These new polymeric materials exhibited tensile stress–strain behavior ranging from soft rubbers through ductile to relatively brittle plastics. The Young's moduli of these polymers varied from 3 to 615 MPa, the ultimate tensile strengths varied from 0.3 to 21 MPa, and the elongation at break varied from 1.6 to 300%. These properties are obviously related to their crosslink densities. The conjugated LoSatSoy oil polymers had higher mechanical properties than the corresponding LoSatSoy oil and regular soybean oil polymers with the same stoichiometry. Some conjugated LoSatSoy oil polymers with appropriate stoichiometries showed yielding behavior in the tensile test process. A variety of new polymer materials can thus be prepared by varying the stoichiometry, the type of soybean oil, and the crosslinking agent. These soybean oil based polymers possessed mechanical properties comparable to those of commercially available rubbery materials and conventional plastics and thus may serve as replacements in many applications. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 60–77, 2001     

On the relevance of the 8‐chain model and the full‐network model for the deformation and failure of networks formed through photopolymerization of multifunctional monomers

Crosslinked networks were synthesized by copolymerization of mono‐functional tert‐butyl acrylate (tBA) with diethyleneglycol dimethacrylate (DEGDMA) or polyethylene glycol dimethacrylates (PEGDMA). By varying the chain length and concentration of the difunctional PEGDMA, we obtained tBA‐PEGDMA copolymer networks while by varying the concentration of difunctional DEGDMA, we obtained tBA‐DEGDMA crosslinked networks. The various materials were submitted to large deformations through uniaxial tension tests. For moderate weight percent of crosslinking agent, up to 20%, the networks showed standard S‐shape stress–strain curves, characteristic of rubber‐like elasticity. Two macromolecular models, the 8‐chain model and the full‐network model, were applied to fit the uniaxial tensile response of the materials. Both models provide good representations of the overall uniaxial stress–strain response of each material. After fitting to stress–strain data, the network models were employed to predict the shear modulus and the elongation at break. Neither the 8‐chain nor the full network model were capable of predicting the failure strain or shear modulus, indicating these models are best used to describe stress–strain relations rather than predict mechanical properties for the network polymers considered here. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1226–1234, 2008     

Irreversible deformation of isotactic polypropylene in the pre-yield regime

In the modeling of the mechanical response of a polymer over a large strain range, the nonlinear viscoelastic and viscoplastic behavior must be considered. For many polymers, nonlinear behavior is observed at low loads, e.g. by a stress-dependence of the creep compliance for stresses above 2 MPa in case of the polypropylene used in this study. Additionally, plastic deformation has been observed at strains below the yield point for several polymers. In this study, the irreversible deformation by cavitation and shear yielding of polypropylene are characterized in the pre-yield regime in uniaxial tensile tests using digital image correlation. The recovery of strain after unloading at a prescribed strain level is measured and used to identify the evolution of the plastic strain during uniaxial tension. An experimental technique for simultaneous determination of the true stress–true strain curve and the degree of stress whitening, which relates to the amount of cavitation, is introduced and the initiation of cavitation is compared to the plastic deformation detected in strain recovery at various temperatures.     

明胶中α组分含量对明胶/羟基磷灰石复合材料力学性能的影响

选用α组分含量分别为20.5%,41%和50%的A、B、C 3种明胶作为原料,采用同时加入法制备了明胶/羟基磷灰石(HAP)复合材料.通过对干态复合物膜拉伸性能的测试和对比,发现,明胶α组分含量的变化对复合材料的弹性模量影响较大,而对拉伸强度和断裂伸长率的影响则相对较小,但总的来说,三者均随α组分含量的增加而增大.其中,α组分含量最高的复合物C的拉伸强度为86.40 MPa,弹性模量为2682.35 MPa,断裂伸长率为8.65%.另外,对复合物C基本性质的表征结果表明,该材料具有类似于自然骨的组成和结构性质,因此有望成为一种具有优异力学性能的骨替代材料.     

Drawing behavior and characteristics of laser‐drawn polypropylene fibers

Drawing behavior, flow drawing, and neck drawing, was studied for isotacticpolypropylene fibers in CO₂ laser drawing system, and the fiber structure and the mechanical properties of drawn fibers were analyzed. For a certain laser power, flow drawing of polypropylene (PP) was possible up to draw ratio (DR) 19.5. Though the drawing stress was very low, the flow‐drawn PP fiber exhibited oriented crystal structure and improved mechanical properties. On the other hand, neck‐drawing was accomplished from DR 4 to 12, with significant increase in drawing stress that enhanced the development of fiber structure and mechanical properties. Unlike PET, the drawing stress depends not only on the DR, but on irradiated laser power also. The 10–12 times neck‐drawn fibers were highly fibrillated. The fibers having tensile strength 910 MPa, initial modulus 11 GPa, and dynamic modulus 14 GPa were obtained by single‐step laser drawing system. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 398–408, 2006     

Fabrication of open‐porous PCL/PLA tissue engineering scaffolds and the relationship of foaming process,morphology, and mechanical behavior

Tissue engineering scaffolds should provide a suitable porous structure and proper mechanical strength, which is beneficial for the delivery of growth factor and regulation of cells. In this study, the open‐porous polycaprolactone (PCL)/poly (lactic acid) (PLA) tissue engineering scaffolds with suitable porous scale were fabricated using different ratios of PCL/PLA blends. At the same time, the relationship of foaming process, morphology, and mechanical behavior in the optimized batch microcellular foaming process were studied based on the single‐factor experiment method. The porous structures and mechanical strength of the scaffolds were optimized by adjusting foaming parameters, including the temperature, pressure, and CO₂ dissolution time. The results indicated that the foaming parameters influence the cell morphology, further determine the mechanical behavior of PCL/PLA blends. When the PCL content is high, with the increase of temperature and time, the cell diameter and the elastic modulus increased, and the tensile strength and elastic modulus increased with the increase of the average cell size, and decreased as the increase of the cell density. While when the PLA content was high, the cell diameter showed the same trend, and the tensile strength and elastic modulus were higher, and the elongation at break was lower, and tensile strength and elastic modulus decreased with the increase of the average cell size and increased with the increase of cell density. This work successfully fabricated optimized porous PCL/PLA scaffolds with excellent suitable mechanical properties, pore sizes, and high interconnectivity, indicating the effectiveness of modulating the batch foaming process parameters.