线性聚酯酰胺对聚碳酸亚丙酯的改性

通过己内酯和氨基己酸开环、缩合反应制备了酯段含量为81%的线性聚酯酰胺（PEA）,并用熔融共混的方法制备了PEA/聚碳酸亚丙酯（PPC）共混物,考察了PEA的引入对共混体系相容性、热力学稳定性和机械性能的影响。 结果表明,PEA与PPC之间有较好的相容性,共混物的热力学稳定性比PPC有显著提高,当PEA质量分数为3%时,共混体系的起始分解温度（T-5%）和最大分解速率时的温度（Tmax）比PPC分别提高了52.7%和46.4%。 通过调节PEA的含量可以使共混体系同时达到增强和增韧的效果。     

Compatibilization of PBT/PP Blends by Adding Side-chain Liquid Crystalline Ionomer with Quaternary Pyridinium Groups

A side-chain liquid crystalline ionomer(SLCI) was synthesized by grafting copolymerization of 4-(4-ethoxybenzoyloxy)-4′-allyloxybiphenyl and N-allyl-pyridium bromide on polymethylhydrosiloxane. The SLCI was blended with polypropylene(PP) and polybutylene terephthalate(PBT) by melt mixing. The thermal behavior, liquid crystalline properties, morphological structure, and mechanical properties of the blends were investigated by differential scanning calorimetry(DSC), polarizing optical microscopy(POM), scannin...     

Determination and comparison of the essentialwork of fracture (EWF) of two polyester blends

The fracture toughness of blends of polypropylene terephthalate (PPT) with polyethylene terephthalate (PET) and polybutylene terephthalate (PBT) were investigated. Binary blends were prepared comprising 10:90, 30:70, 50:50, 70:30 and 90:10 mass/mass%. The fracture toughness was determined for each blend using the essential work of fracture (EWF) method and thin film double edge notched tension (DENT) specimens. The specific essential work of fracture, w _e, values obtained for blends of PET/PPT ranged from 27.33 to 37.38 kJ m^–2 whilst PBT/PPT blends yielded values ranging from 41.78 to 64.23 kJ m^–2. Differential scanning calorimetry (DSC) was employed to assess whether or not crystallinity levels influence the mechanical properties evaluated. The fracture toughness of PPT deteriorated with PET incorporation. However, high we values exceeding that of pure PPT were obtained for PBT/PPT blends across the composition range studied.     

Investigating properties of poly (ether‐amide)/MWCNT nanocomposite films containing 2,7‐bis(4‐aminophenoxy)naphthalene and isophthalic segments

Three nanocomposite films based on aramid (poly (ether‐amide), PEA) and multiwall carbon nanotubes (MWCNT) were prepared via solution casting method using 2,7‐bis(4‐aminophenoxy)naphthalene (4) and isophthalic acid (5) containing various amounts of MWCNT (2, 3, 5 wt.%). To comprehensively analyze the properties of the cast films as well as the monomers, different techniques were employed, namely FT‐IR, ¹H NMR, X‐ray diffraction, and field emission scanning electron microscopy. Also, thermal and tensile properties of PEA (6) and nanocomposite films were investigated using thermogravimetric analysis and mechanical analysis, respectively. The morphology, thermal, and mechanical properties of nanocomposite films approved that MWCNT had well dispersion in the PEA matrix and showed a synergistic effect on improving all of the investigated properties. Based on the thermogravimetric analysis results, employing MWCNT caused to increase in the char yields from 61 (in the neat PEA) to 66 (in the PEA /MWCNT nanocomposite 5 wt.%) under the nitrogen atmosphere. In comparison to the pristine PEA (426°C), the temperature at 10 losses mass % (T₁₀) was increased from 530°C to 576°C, with 2 to 5 wt.% of MWCNT. Mechanical analysis revealed that the tensile strength and initial modulus were improved by incorporating MWCNT into PEA (81.70–93.40 MPa and 2.10–2.22 GPa, respectively). Electrical conductivity of the PEA/MWCNT nanocomposites was displayed maximum value in the 5 wt.%, showing satisfactory value in many application areas. The X‐ray diffraction technique was employed to study the crystalline structure of the prepared nanocomposite films as well as PEA. In addition, the electrochemical impedance spectroscopy study demonstrated that the prepared nanocomposites had significant impedance improvement in the presence of MWCNTs.     

酯交换反应对PBT／PC共混体系相容性及热行为的影响

研究了ＰＢＴ、ＰＣ间的酯交换反应及共混体系的相容性和热行为。ＩＲ结果表明，在熔融共混过程中ＰＢＴ、ＰＣ间发生了酯交换反应，磷酸三苯酯可在一定程度上抑制酯交换反应的进行，但是当温度过高或共混时间过长时，ＴＰＰ的作用减弱甚至消失。     

Novel copolyesters based on poly(alkylene dicarboxylate)s: 1. Thermal behavior and biodegradation of aliphatic-aromatic random copolymers

In order to improve the thermal and mechanical properties of the poly(butylene 1,12-dodecanedioate), some novel aliphatic-aromatic random copolyesters have been prepared by starting from 1,4-butanediol and different molar ratio of 1,12-dodecanedioc acid and terephthalic acid. The samples were characterized by ¹H NMR and the molecular structure was correlated with the crystalline phase present, the level of crystallinity, the glass transition temperature, the mechanical behavior, and the biodegradability. In particular, the copolymer containing the 70 mol% of PBT repeating units notably improves the thermal and mechanical properties of the poly(butylene 1,12-dodecanedioate) towards those of PBT and maintains a very high thermal stability, but loses the biodegradability of the poly(alkylene dicarboxylate). Therefore, for this class of aliphatic-aromatic copolymers the chemical composition must be carefully chosen to reach a compromise between good thermal and mechanical performances and biodegradability, according to the necessity.     

Transesterification and crystallization behavior of poly(butylene succinate)/poly(butylene terephthalate) block copolymers

The block copolymers of poly(butylene succinate) (PBS) and poly(butylene terephthalate) (PBT) were synthesized by melt processing for different times. The sequence distribution, thermal properties, and crystallization behavior were investigated over a wide range of compositions. For PBS/PBT block copolymers it was confirmed by statistical analysis from ¹H-NMR data that the degree of randomness (B) was below 1. The melting peak (T_m) gradually moved to lower temperature with increasing melt processing time. It can be seen that the transesterification between PBS and PBT leads to a random copolymer. From the X-ray diffraction diagrams, only the crystal structure of PBS appeared in the M1 copolymer (PBS 80 wt %) and that of PBT appeared in the M3 (PBS 50 wt %) to M5 (PBS 20 wt %) copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 147–156, 1998     

Miscibility and crystallization behavior of PBT/epoxy blends

The miscibility and the isothermal crystallization kinetics for PBT/Epoxy blends have been studied by using differential scanning calorimetry, and several kinetic analyses have been used to describe the crystallization process. The Avrami exponents n were obtained for PBT/Epoxy blends. An addition of small amount of epoxy resin (3%) leads to an increase in the number of effective nuclei, thus resulting in an increase in crystallization rate and a stronger trend of instantaneous three‐dimensional growth. For isothermal crystallization, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of PBT component in the PBT/Epoxy blends. The Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT/Epoxy 97/3 had lower nucleation constant K_g than 100/0, 93/7, and 90/10 PBT/Epoxy blends. Analysis of the crystallization data of PBT/Epoxy blends showed that crystallization occurs in regime II. The fold surface free energy, σ_e = 101.7–58.0 × 10^?3 J/m², and work of chain folding, q = 5.79–3.30 kcal/mol, were determined. The equilibrium melting point depressions of PBT/Epoxy blends were observed and the Flory–Huggins interaction parameters were obtained. It indicated that these blends were thermodynamically miscible in the melt. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1320–1330, 2006     

Preparation of core-shell structured polyacrylic modifiers and effects of the core-shell weight ratio on toughening of poly(butylene terephthalate)

Core-shell structured polyacrylic(named CSSP) impact modifiers consisting of a rubbery poly(n-butyl acrylate) core and a rigid poly(methyl methacrylate) shell with a size of about 353 nm were prepared by seed emulsion polymerization. The CSSP modifiers with different core-shell weight ratios(90/10, 85/15, 80/20, 75/25, 70/30, 65/35 and 60/40) were used to modify the toughness of poly(butylene terephthalate)(PBT) by melt blending. It was found that the polymerization had a very high instantaneous conversion(> 95.7%) and overall conversion(99.7%). The morphology of the core-shell structure was confirmed by means of transmission electron microscopy. Scanning electron microscopy was used to observe the morphology of the fractured surfaces. Differential scanning calorimeter was used to study the crystallization behaviors of PBT/CSSP blends. The dynamic mechanical analyses of PBT/CSSP blends showed two merged transition peaks of PBT matrix, with the presence of CSSP core-shell structured modifier, that were responsible for the improvement of PBT toughness. The results indicated that the notch impact strength of PBT/CSSP blends with a core-shell weight ratio of 75/25 was almost 8.64 times greater than that of pure PBT, and the mechanical properties agreed well with the SEM observation.     

Miscibility and properties of poly(l-lactic acid)/poly(butylene terephthalate) blends

Binary blends of poly(l-lactide) (PLLA) and poly(butylene terephthalate) (PBT) containing PLLA as major component were prepared by melt mixing. The two polymers are immiscible, but display compatibility, probably due to the establishment of interactions between the functional groups of the two polyesters upon melt mixing. Electron microscopy analysis revealed that in the blends containing up to 20% of poly(butylene terephthalate), PBT particles are finely dispersed within the PLLA matrix, with a good adhesion between the phases. The PLLA/PBT 60/40 blend presents a co-continuous multi-level morphology, where PLLA domains, containing dispersed PBT units, are embedded in a PBT matrix. The varied morphology affects the mechanical properties of the material, as the 60/40 blend displays a largely enhanced resistance to elongation, compared to the blends with lower PBT content.     

热致液晶共聚酯酰胺／PET共混物的流变性能和原位增强特性

采用Ｉｎｓｔｒｏｎ３２１１型毛细管流变仪研究了ＰＥＡ／ＰＥＴ共混物的流变性能，据此探讨共混物熔体的可纺性，讨论了共混物配比与复合纤维力学性能的关系，并且偏光显微镜，扫描电镜研究纤维的结构。结果表明，共混物的表观粘度低于ＰＥＴ的粘度，当ＰＥＡ为１０％，共混物的表观粘度达到最小值；且ＰＥＡ含量低于１０％时，共混物的可纺性即，表现出良好的原位增强效果。     

磷酸三苯酯对PBT／PET共混体系结晶行为的影响

用广角Ｘ－角线衍射法和差法扫描量热法研究了磷酸三苯酯对ＰＢＴ／ＰＥＴ共混体系结晶行为影响，结果表明：ＴＰＰＷ作为该共混体系的稳定剂，只能延长在熔融状态下酯交换反应发生的时间，ＴＰＰ含量一定时，熔融时间增加，ＰＢＴ，ＰＥＴ之间的酯交换反应同样会发生，不同熔融时间，就要求ＴＰＰ的用量也不相同。ＴＰＰ在ＰＢＴ／ＰＥＴ共混体系中没有结晶成核剂的作用，它也不改变ＰＢＴ，ＰＥＴ的结晶结构。     

Effects of Zinc oxide nanoparticles on the morphology and viscoelastic properties of polyamide 6/poly(butylene terephthalate) blends

The morphology of polyamide 6/poly(butylene terephthalate)(PA6/PBT, 70/30, W/W) blends filled with pristine Zinc oxide(ZnO) nanoparticles and ZnO surface-modified by γ-glycidoxypropyltrimethoxysilane(K-ZnO) was investigated. The incorporation of ZnO and K-ZnO by one-step compounding both resulted in a smaller size and narrower distribution of PBT domains and the effect of ZnO was greater than K-ZnO. To reveal the underlying mechanism, two-step compounding in which ZnO or K-ZnO was premixed with PA6 or PBT was conducted and the finest morphology was achieved when mixing PA6 with premixed PBT/ZnO. Transmission electron microscopy(TEM) demonstrated that ZnO was distributed in PBT in all cases and K-ZnO was enriched at the interface except when K-ZnO was premixed with PBT. ZnO and K-ZnO caused a deterioration in the melt rheological properties of PBT, which played a dominating role in the morphological changes. In addition, the interfacial localization of K-ZnO enhanced the dynamic rheological properties of PA6/PBT blends substantially.     

Preparation and Characterization of Blend Films of Poly(Vinyl Alcohol) and Sodium Alginate

Blend films of poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared by casting from aqueous solutions. This blend films were characterized by tensile strength test, Fourier transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The miscibility in the blends of PVA and NaAlg was established on the basis of the thermal analysis results. DSC showed that the blends possessed single, composition‐dependent glass transition temperatures (T_gs), indicating that the blends are miscible. FT‐IR studies indicate that there is the intermolecular hydrogen bonding interactions, i.e. –OH…^?OOC– in PVA/NaAlg blends. The blend films also exhibited the higher thermal stability and their mechanical properties improved compared to those of homopolymers.     

Orientation and mechanical properties of PBT and its blends with a liquid-crystalline copolyester

Blends of poly (butylene terephthalate) (PBT) and a liquid-crystalline copolyester (60 mol % poly(p-hydroxy benzoic acid)/40 mol % polyethylene terephthalate) (LCP) were prepared in the melt state. The investigation of mechanical properties indicated that, for the processing conditions used, neither the addition of up to 30 wt % LCP to PBT nor the cooling history affected significantly the tensile modulus E. For oriented specimens, a marked improvement of E was obtained for all the blends, and increased with the LCP content. This improvement was more marked for slowly cooled samples. X-ray diffraction was used to quantify the orientation of the crystalline PBT and liquid-crystalline LCP phases. It was shown that neither the thermal history nor the presence of up to 30 wt % LCP affected the orientation behavior of the PBT crystalline phase. For the LCP phase, measurements were not possible for concentrations lower than 10 wt %, and were more difficult and less precise than for PBT. Nevertheless, it was possible to show that a better orientation was obtained for the slowly cooled samples and for higher concentrations of LCP in the blends. This correlated with the enhancement of mechanical properties observed for the oriented samples.     

Modification of Interfacial Interaction of PBT/PP Blends by Adding Main-chain Liquid Crystalline Ionomer with Sulfonic Group

A main-chain liquid crystalline ionomer(MLCI)containing sulfonic group was synthesized by an interfacial condensation reaction.The MLCI was blended with polybutylene terephthalate(PBT)and polypropylene...     

The structure and physical properties of in situ composites based on semiflexible thermotropic liquid crystalline copolyesteramide and poly(butylene terephthalate)

Liquid crystalline polymer–poly(butylene terephthalate) (LCP/PBT) blends were prepared by melt mixing. The LCP employed was a thermotropic copolyesteramide based on 30 mol % of p‐amino benzoic acid (ABA) and 70 mol % of poly(ethylene terephthalate) (PET). The thermal, dynamic mechanical and rheological properties, morphology, and crystal structure of LCP/PBT blends were studied. The results showed that the semiflexible ABA30/PET LCP is miscible in the melt state with PBT, and they are partial miscible in the solid state. Differential scanning calorimetric measurements showed that the introduction of the semiflexible LCP into LCP/PBT blends retards the crystallization rate of PBT. However, the LCP dispersed phase acted as the sites for the nucleation of spherulites and enhance the degree of crystallinity of PBT. Hot‐stage optical microscopy examination revealed that the LCP microfibers with random orientation are dispersed in the PBT matrix of compression molded LCP/PBT blends. Under the application of a shearing force, the LCP domains in the PBT matrix tended to deform into microfibers, and to orient themselves along the flow direction. The formation of microfibers resulted in an increase of the storage modulus. The torque measurements indicated that the melting viscosity of the LCP/PBT blends is much lower than that of the pure PBT. Finally, the wide‐angle X‐ray diffraction patterns indicated that PBT shows no structural change with the incorporation of LCP, but the apparent crystal sizes of several diffraction planes change significantly. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 403–414, 2000     

The impact of resorcinol bis(diphenyl phosphate) and poly(phenylene ether) on flame retardancy of PC/PBT blends

Flame retardancy of bisphenol A polycarbonate (PC)/poly(butylene terephthalate) (PBT) blends was improved by the addition of resorcinol bis(diphenyl phosphate) (RDP) and poly(phenylene ether) (PPO). A PC/PBT blend at 70/30 weight ratio obtained a V‐0 rating by the addition of 10 wt% RDP and 10 wt% PPO. The combination of 5 wt% methyl methacrylate‐butadiene‐styrene tercopolymer (MBS) with 3 wt% ethylene‐butylacrylate‐glycidyl methacrylate tercopolymer (PTW) causes a remarkable increase in toughness of the PC/PBT/RDP blend while maintaining a high rigidity. A detailed investigation of the flame‐retardant action of PC/PBT/RDP and PC/PBT/RDP/PPO blends was performed using thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), TGA‐FTIR, temperature‐programmed pyrolysis/gas chromatography/mass spectrometry (TPPy/GC/MS), and scanning electron microscopy/energy dispersive spectrometer (SEM/EDS). The results demonstrate that RDP induces a higher char yield at ca. 450 °C and synchronously increases the thermal stability of the blend with PPO. The flame‐retardant role of RDP in the condensed phase was discerned from TGA, FTIR, and SEM/EDS of the residues. Copyright © 2010 John Wiley & Sons, Ltd.     

Inherent flame retardation of bio-based poly(lactic acid) by incorporating phosphorus linked pendent group into the backbone

The molecular design for inherently flame-retardant poly(lactic acid) (IFR-PLA) was outlined and achieved by chemically incorporating an effective organophophorus-type flame retardant (FR) into the PLA backbone via the chain extension of the dihydroxyl-terminated prepolymer with 1, 6-hexamethylene diisocyanate (HDI). The structure of IFR-PLA was characterized by ¹H- and ³¹P-nuclear magnetic resonance (NMR) and Fourier transform infrared (FTIR) spectroscopy. IFR-PLA was further blended with the commercial PLA to prepare flame retardant PLA blends (PLA-FR blend). The relevant properties of IFR-PLA and PLA-FR blends were evaluated by differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), limiting oxygen index (LOI) measurements and UL-94 tests. The thermal analysis revealed that the char yield of IFR-PLA and PLA-FR blend above 400 °C was greatly enhanced compared to that of pure PLA. The LOI value was significantly improved from 19 for pure PLA to 29 when 1 wt% of phosphorus content was introduced and all IFR-PLA samples achieved V-0 rating in the UL-94 tests. PLA-FR blends had an LOI value of 25-26 and UL-94 V-2 rating at 20 wt% of IFR-PLA content. The tensile strength of all the FR PLA systems was ca. 60 MPa. The method used in this study provided a novel route to permanently flame retard PLA.     

Thermal Properties and Morphology of Liquid Crystalline Copolyester and Polyester Elastomer Blends

Abstract

Polyester elastomer (PEL) blends having a hard segment of polyester (PBT), soft segment of polyether (PTMG), and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate) were prepared with a twin-screw extruder. Test specimens for thermal properties were prepared by injection molding. Rheological properties and morphology were investigated by Instron capillary rheometer (ICR) and scanning electron microscopy (SEM). Thermal properties of the LCP/PEL blends were investigated by DSC, dilatometer, heat deflection temperature tester, and a Rheovibron viscometer. DSC study revealed a partial miscibility between LCP and PEL. It was found that the LCP acted as a nucleating agent for the crystallization of PEL in the LCP/PEL blends. The dimensional and thermal stability of the blends were increased by increasing the LCP cont-ent. The storage modulus (E' was improved by increasing the LCP content. The blend viscosity showed a minimum value at 5 wt% of LCP which increased by increasing the LCP content above 5 wt% of LCP The morphology of the LCP/PEL blends showed poor interfacial adhesion between the two phases, and the fibrillar structure of LCP phase in the matrix was affected by the LCP content, shear rate, and extrusion temperature. The morphology of the blends was found to be affected by their compositions and processing conditions.