Stability of sulfonated derivatives of benzene and naphthalene on disposable solid-phase extraction pre-columns and in an aqueous matrix

The stability of 14 sulfonated benzene and naphthalene compounds was investigated using polymeric solid-phase extraction cartridges, based on the styrene-divinylbenzene polymer Isolute ENV+. Several different storage conditions were tested to carry out the stability study in polymeric cartridges, which included storage at room temperature, at 4 degrees C and at -20 degrees C, during a period of up to 3 months. An additional stability study was carried out, not with the polymeric solid matrix, but in an aqueous matrix. This study was performed storing the samples at 4 degrees C, during 2 months under three different conditions: acidifying the water sample to pH 2.5-3 with sulfuric acid, adding 1% of formaldehyde (additive used in waste water analyses), and storing the water sample at 4 degrees C without any additives. The extraction of the SPE process is analyzed by ion-pair chromatography-electrospray mass spectrometry, in the negative ion mode. This study showed that the stability of polar aromatic sulfonic acids on disposable polymeric cartridges and in the water matrix is related to temperature and pH, respectively. Target aromatic sulfonated compounds stored in polymeric solid-phase extraction cartridges, are more stable at lower temperatures. The target analytes showed also good stability when stored in water at acidic pH. From the different analytes studied, substituted naphthalenesulfonates suffered more degradation than mononaphthalenesulfonates or benzenesulfonates under the experimental conditions of this work.     

An investigation of dynamic mechanical, thermal, and electrical properties of housing materials for outdoor polymeric insulators

The present paper reports the results about a study of mechanical, thermal, dynamic mechanical and electrical properties of housing (weather shed) materials for outdoor polymeric insulators. Silicone rubber, ethylene-propylene-diene monomer (EPDM) and alloys of silicon-EPDM are known polymers for use as housing in high voltage insulators. The result of dynamical mechanical measurement shows that the storage modulus of blends enhances with increase EPDM in formulation. It can be seen from the result of TGA measurement that initial thermal degradation of silicone rubber improves by the effect of EPDM in blends. The blends of silicone-EPDM show good breakdown voltage strength compared to silicone rubber. Surface and volume resistance of silicone rubber improve by EPDM content. The mechanical properties of EPDM such as strength, modulus and elongation at break improve by silicone.     

Enantioselective Separation of Basic Drugs by CE with Polygalacturonic Acid as a Novel Chiral Selector

Polygalacturonic acid, a linear high molecular weight homopolysaccharide was investigated as a chiral selector in capillary zone electrophoresis for the separation of enantiomers of basic drugs. The choices of running buffer pH and concentration of chiral selector were found to be important for the improvement of enantioselectivity. The effects of background electrolyte concentration and the capillary temperature on the separation were also examined. Enantioseparations were carried out in the acidic conditions using 1.5% polygalacturonic acid (w/v) in a 40 mM phosphate buffer under an applied voltage of 15 kV. The optimization of these separations was dependent on the nature of the analytes and could be achieved by the proper choice of experimental conditions. A brief mechanism of enantiorecognition by polygalacturonic acid was also given.     

Study on permeation behavior and chemical degradation of PA66 in acid solution

In many polymers under corrosive liquids, degradation followed after permeation of environmental solution for a long period. The permeation rate of environmental solution, in many cases, is very low in corrosion-resistant polymeric materials. Therefore, the observation of the permeation of environmental solution and degradation of polymeric materials are very difficult in practical application. A simulation of permeation of solution is required in order to understand the permeation behavior of environmental solution and polymer degradation. A detailed analysis of the permeation behavior of solution accompanied by chemical reaction is important to study for improving the lifetime of polymers. Polyamide 66 (PA66) and sulfuric acid solution were used to investigate the quantitative study of permeation of environmental solution and its relation to degradation of polymeric materials. Correlation between diffusion process and degradation of PA66 related to the decrease of weight average molecular weight was defined. The diffusion rate of sulfuric acid solution was found to increase by decreasing weight average molecular weight of PA66 due to the established chain scission by hydrolysis reaction. The permeation of sulfuric acid solution that affected the decomposition reaction was modeled and quantitative evaluation of permeation of sulfuric acid was established.     

The Effect of Poly(methyl vinyl ether-alt-maleic acid) Stabilizer on the Stability of Polyaniline-Poly(methyl vinyl ether-alt-maleic acid) Dispersions

The polyaniline (PANI) dispersions have been prepared in acidic aqueous media by oxidative dispersion polymerization in the presence of a polymeric stabilizer. The polymeric stabilizer used in this study is the poly(methyl vinyl ether-alt-maleic acid) (PMVEMA) which contains acid groups (-COOH). The PANI-PMVEMA particles have a uniform size and a spherical shape. The PANI-PMVEMA dispersions show almost no desorption of the PMVEMA, even though the sonication at 500 W for 20 min and the centrifugation at 500 rpm for 60 min are performed 10 times. The existence of the PMVEMA on the surface is confirmed by X-ray photoelectron spectroscopy. The dispersion stability of the PANI-PMVEMA dispersions is extensively influenced by zeta potential which was governed by the acid group (-COOH) of the PMVEMA on the PANI-PMVEMA particle surface. Copyright 2000 Academic Press.     

Enantioselective Separation of Basic Drugs by CE with Polygalacturonic Acid as a Novel Chiral Selector

Polygalacturonic acid, a linear high molecular weight homopolysaccharide was investigated as a chiral selector in capillary zone electrophoresis for the separation of enantiomers of basic drugs. The choices of running buffer pH and concentration of chiral selector were found to be important for the improvement of enantioselectivity. The effects of background electrolyte concentration and the capillary temperature on the separation were also examined. Enantioseparations were carried out in the acidic conditions using 1.5% polygalacturonic acid (w/v) in a 40 mM phosphate buffer under an applied voltage of 15 kV. The optimization of these separations was dependent on the nature of the analytes and could be achieved by the proper choice of experimental conditions. A brief mechanism of enantiorecognition by polygalacturonic acid was also given.

     

用钙试剂羧酸钠为指示剂络合滴定法测定降水中钙离子

提出用钙试剂羧酸钠作指示剂络合滴定法测定降水中钙离子,在自然条件下终点的观察即能顺利进行。同《空气和废气监测分析方法》中钙离子络合滴定法相比较,此法终点敏锐,回收率为９５％～１００％,相对标准偏差均小于２．７％,方法简便、快速、准确、灵敏。具有推广性。     

FEM simulation of polymeric foam with random pore structure: Uniaxial compression with loading rate effect

This study establishes FEM modeling for compressive deformation behavior of polymeric foams with different loading rates. The polymeric foam used in this study was made from polypropylene (the base matrix of the polymer) with porosity of about 95%. The pore size and shape were randomly distributed in the foam. The X-ray CT method was first conducted to observe the microstructure, the geometric feature of which was reproduced in the FEM model. Uniaxial compression tests with different loading speeds were carried out to investigate an effect of loading rate (strain rate) dependency on the deformation behavior. By using the X-ray CT method, in situ observation of microscopic deformation was carried out. Furthermore, FEM computations were carried out to simulate macroscopic and microscopic deformation behaviors. The random porous structure was modeled using Surface Evolver. The elastoplastic property with strain rate dependency was used in this model. The established FEM framework may be useful for a porous polymer with a random pore structure and for deformation modeling with strain rate effect.     

Influence of several experimental parameters on As and Se leaching from coal fly ash samples

Coal fly ash leaching process for As and Se is studied. Environmental parameters such as pH, temperature, solid-liquid ratio, particle size and leaching time are taken into account in order to simulate As and Se leaching process for disposal coal fly ash. Analysis of reference materials was carried out by using of hydride generation coupled to atomic fluorescence spectrometry. Plackett-Burman experimental design is used to know the significative parameters, and Box-Behnken experimental design is used to refine the results obtained for these significative parameters. pH and temperature shown a hardly influence in leaching process. Furthermore, leaching time was also significative. According our results, it may be assumed that percentage of As and Se leaching in experimental conditions tested is relatively low for acidic fly ashes.     

一种超硬新材料BeP2N4的电子结构和力学性质及本征硬度

基于密度泛函理论,采用局域密度近似(LDA)和广义梯度近似(GGA)泛函研究了硅铍石、尖晶石结构的 BeP₂N₄ 材料的晶格参数、能带结构、态密度、分态密度、Mulliken布居值和弹性性质, 计算结果与已有的实验值和理论值符合很好. 能带结构和态密度表明两种结构的BeP₂N₄材料是宽的直接带隙的绝缘体材料. 尖晶石结构BeP₂N₄的体弹性模量、剪切模量和弹性模量比硅铍石结构的相应的力学量大得多. 利用Sung等提出的硬度经验判据和Gao等提出的基于Mulliken轨道重叠布居数的共价固体本征硬度计算方法, 预测了两种结构的本征硬度值. 计算结果表明硅铍石结构BeP₂N₄虽然体弹模量小, 但是它并不是一种软的材料, 而是一种易脆的硬度较硬的材料, 随着压力增加硅铍石结构BeP₂N₄的脆性逐渐过渡到延性. 尖晶石结构BeP₂N₄是一种易脆的超硬材料. 采用GGA计算得到的硅铍石BeP₂N₄向尖晶石相转变压力为14 GPa, 与理论预测值(24 GPa)相比偏小.     

Use of poly(sodium oleyl-L-leucylvalinate) surfactant for the separation of chiral compounds in micellar electrokinetic chromatography

A chiral amino acid-based monomeric and polymeric surfactant, sodium oleyl-L-leucylvalinate) (L-SOLV) and poly(sodium oleyl-L-leucylvalinate) (poly-L-SOLV) were synthesized and used for chiral separations in micellar electrokinetic chromatography (MEKC). Poly-L-SOLV was used successfully in the separation of various enantiomers of neutral, acidic, and basic analytes such as 1,1'-bi-2-napthol, 1,1'-binaphthyl-2,2'-diamine, benzoin, hydrobenzoin, benzoin methylether, warfarin, and coumachlor obtaining well-resolved peaks but with only partial separation of temazepam. In addition, the atropisomer 1,1'-binaphthyl-2, 2'-dihydrogen phosphate was chosen to study the applicability of the polymeric surfactant over a wide range of parameters such as concentration, temperature, voltage, and pH. The most striking characteristic of this new surfactant is its high hydrophobicity. It is favorable to interactions with hydrophobic chiral analytes, and thus may provide better chiral recognition for the compounds.     

A study of the interaction between humic acids and acidic metabolites of phenanthrene by capillary electrophoresis

Humic acids (HA) are able to interact with a wide range of pollulants and can influence their solubility, transport and bioavailability. In order to study the interaction between polar aromatic hydrocarbons and these macromolecules, an affinity capillary electrophoretic method, the Hummel-Dreyer (HD) method in its modified version, has been used. Two acidic metabolites of phenanthrene: 1-hydroxy-2-naphthoic acid (1-HNA) and 3,4-dihydroxybenzoic acid (3,4-DBA) were studied. The analysis for the binding studies was carried out by injecting a solution of HA in 25 mM ammonium hydrogen carbonate buffer (pH 9) into an uncoated fused-silica capillary, filled with buffer solutions of 1-HNA or 3,4-DBA in varying and increasing amounts. The results obtained indicate that both compounds bind to HA, as had been confirmed by dialysis experiments and literature data. CE proved to be a useful technique for investigating the link between xenobiotics and environmental macromolecules.     

Multi-residue determination of veterinary drugs in milk by ultra-high-pressure liquid chromatography-tandem mass spectrometry

Stir bar sorptive extraction with polyurethane (PU) and polydimethylsiloxane (PDMS) polymeric phases followed by high-performance liquid chromatography with diode array detection [SBSE(PU or PDMS)/HPLC-DAD] was studied for the determination of six acidic pharmaceuticals [o-acetylsalicylic acid (ACA), ibuprofen (IBU), diclofenac sodium (DIC), naproxen (NAP), mefenamic acid (MEF) and gemfibrozil (GEM)], selected as non-steroidal acidic anti-inflammatory drugs and lipid regulators model compounds in environmental water matrices. The main parameters affecting the efficiency of the proposed methodology are fully discussed. Assays performed on 25 mL of water samples spiked at the 10 microg L(-1) level under optimized experimental conditions, yielded recoveries ranging from 45.3+/-9.0% (ACA) to 90.6+/-7.2% (IBU) by SBSE(PU) and 9.8+/-1.6% (NAP) to 73.4+/-5.0% (GEM) by SBSE(PDMS), where the former polymeric phase presented a better affinity to extract these target analytes from water matrices at the trace level. The methodology showed also excellent linear dynamic ranges for the six acidic pharmaceuticals studied, with correlation coefficients higher than 0.9976, limits of detection and quantification between 0.40-1.7 microg L(-1) and 1.5-5.8 microg L(-1), respectively, and suitable precision (RSD <15%). Moreover, the developed methodology was applied for the determination of these target analytes in several environmental matrices, including river, sea and wastewater samples, having achieved good performance and moderate matrix effects. In short, the PU foams demonstrated to be an excellent alternative for the enrichment of the more polar metabolites from water matrices by SBSE, overcoming the limitations of the conventional PDMS phase.     

煤中溴的淋滤行为研究

在不同pH值条件下对来自重庆磨心坡矿煤样进行柱淋滤实验,用电感耦合等离子体质谱法( ICP-MS )测定煤中溴的含量及四种淋滤介质在不同时间段获取的淋出液中溴的浓度。结果表明,淋滤液的pH值、淋滤时间、煤中溴的赋存形态及在煤中赋存部位对溴的淋出有重要影响。淋滤液的酸性越强,煤中溴的最大淋出浓度越大,一定时间内溴的总淋出率也越高。 pH值为2的淋滤液,在淋滤前40h内淋出溴的量占总淋出量的80.65%;pH值为4的淋滤液,在淋滤前50h内淋出溴的量占总淋出量的89.42%。在酸性淋滤液作用下,首先被淋出的是存在煤颗粒表面的碳酸盐态和铁锰结合态溴,然后煤基质内部的水溶态和离子交换态溴才被淋出。柱淋滤实验表明,煤中溴在风化过程中,会被酸性雨水淋溶出来进入周围土壤或地表水体,造成周围环境溴的富集。     

Experimental study and performance evaluation of various cook stove models based on energy and exergy analysis

This article presents the experimental study and comparative performance evaluation of four types of cook stoves using energy and exergy analysis. Analysis of four different types of cook stove models viz. Envirofit, Mangla, Harsha and Vikram were selected and the water boiling test has been carried out. The suitable biomass available from the local market was prepared in the proper size as described in the Bureau of Indian Standards (BIS) and has been used as the fuel for cook stove in this experimental study. The aluminium pots of proper capacity as per BIS standard have been used for different cook stoves. The data from the experiments was collected and evaluated for the energy and exergy efficiencies for different models. Based on the data analysis it is found that the exergy efficiency is much lower than that of the energy efficiency for all the four models. It is also found that the both the efficiencies of Envirofit model are found to be higher than those of other models studied here.     

Determination of butyl- and phenyltin compounds in sediments by GC-FPD after NaBEt(4) ethylation

A reliable and rapid speciation method for the simultaneous determination of butyl- and phenyltin species in sediment samples has been developed. Two extraction procedures are compared: methanolic hydrochloric acid (at four different concentrations) and ethanoic acid leaching. Derivatization is carried out by the one-step ethylation/extraction procedure using the sodium tetraethylborate reagent directly in aqueous phase in the presence of an isooctane layer. Analysis is performed by capillary gas chromatography hyphenated to flame photometric detection (GC-FPD). Detection limits range from 0.5 to 1.5 ng(Sn) g(-1)(dry weight). Analysis of environmental samples and certified reference materials demonstrate the accuracy of the analytical method.     

Immunopharmacological Properties of Methacrylic Acid Polymers as Potential Polymeric Carrier Constituents of Anticancer Drugs

Cytostatic chemotherapeutics provide a classical means to treat cancer, but conventional treatments have not increased in efficacy in the past years, warranting a search for new approaches to therapy. The aim of the study was, therefore, to obtain methacrylic acid (MAA) (co)polymers and to study their immunopharmacological properties. 4-Cyano-4-[(dodecylsulfanylthiocarbonyl)sulfanyl] pentanoic acid (CDSPA) and 2-cyano-2-propyl dodecyl trithiocarbonate (CPDT) were used as reversible chain transfer agents. Experiments were carried out in Wistar rats. The MTT assay was used to evaluate the cytotoxic effect of the polymeric systems on peritoneal macrophages. An experimental tumor model was obtained by grafting RMK-1 breast cancer cells. Serum cytokine levels of tumor-bearing rats were analyzed. The chain transfer agents employed in classical radical polymerization substantially reduced the molecular weight of the resulting polymers, but a narrow molecular weight distribution was achieved only with CDSPA and high CPDT concentrations. Toxicity was not observed when incubating peritoneal macrophages with polymeric systems. In tumor-bearing rats, the IL-10 concentration was 1.7 times higher and the IL-17 concentration was less than half that of intact rats. Polymeric systems decreased the IL-10 concentration and normalized the IL-17 concentration in tumor-bearing rats. The maximum effect was observed for a MAA homopolymer with a high molecular weight. The anion-active polymers proposed as carrier constituents are promising for further studies and designs of carrier constituents of drug derivatives.     

Highly-sensitive micellar electrokinetic chromatographic analysis of dioxin-related compounds using on-line concentration.

An application study of an on-line concentration technique of neutral analytes for micellar electrokinetic chromatography (MEKC) was carried out in environmental analysis to enhance the UV detection sensitivity. Several dioxins and related compounds, such as dibenzofuran, dibenzo-p-dioxin, 2,3- and 2,7-dichlorodibenzo-p-dioxins, and 2,3,7-trichlorodibenzo-p-dioxin, were used as test solutes. For a highly sensitive separation and detection, cyclodextrin-modified MEKC (CD-MEKC) under acidic conditions was employed as a separation mode and stacking using reverse migrating micelles and a water plug (SRW) as an on-line concentration technique. Almost a 200-fold gain in detection sensitivity was obtained for the model compounds in SRW-CD-MEKC compared to that in normal CD-MEKC without on-line concentration and the limit of detection was found to be around 0.1 ppm for each solute.