A novel composite Nafion membrane for direct alcohol fuel cells

Trifluoromethanesulfonic acid or triflate acid, chemical formula CF₃SO₃H, is regarded as one of the strongest acids and resembles Nafion^® in structure. Erbium triflate, a lanthanum salt of triflate, is thermally stable. This paper reports data on the formation of membranes by the fixation of erbium triflate salts (ErTfO) into the Nafion structure. Five different loadings of ErTfO were used to fabricate ErTfO/Nafion composite membranes and these were characterized, extensively for possible use in direct alcohol fuel cells. The membranes were characterized using XRD, TGA, FTIR, and for mechanical strength, water uptake, ion exchange capacity, alcohol uptake, swelling, proton conductivity, alcohol permeability and oxygen stability. The ErTfO/Nafion composite membranes reduced alcohol permeability by 77–80%. The proton conductivity of 3% ErTfO/Nafion composite membranes was 38% higher than that of a pure cast Nafion membrane. The oxygen stability of the ErTfO/Nafion composite membranes was higher than pure cast Nafion. However, the mechanical strength of 7% and 9% ErTfO/Nafion was lower than that of pure cast Nafion. The composite membrane was chemically stable and has potential for use in direct alcohol fuel cells.     

Synthesis and Ex-situ Characterization of Nafion/TiO2 Composite Membranes for Direct Ethanol Fuel Cell

Nafion/TiO₂ composite membranes for different loadings of TiO₂ were prepared by casting method for the possible application in direct ethanol fuel cell (DEFC). The properties of the composite membranes were investigated by scanning electron microscopy (SEM), x-ray diffraction (XRD), thermogravimetric analyser (TGA), ion exchange capacity, water and alcohol uptake, swelling ratio, proton conductivity, and ethanol crossover. The observed characteristics of the membranes were evaluated for DEFC and compared with the direct methanol fuel cell (DMFC) membrane. The analysis reveales a significant influence on the TiO₂ surface characteristics, water and alcohol uptake, and swelling of the membrane. The TiO₂ composite membranes exhibited a sharp decrease in methanol and ethanol crossover for 5% TiO₂ and the proton conductivity was heighest for 1% TiO₂ loading. The best compromise between proton conductivity and crossover has been found out with the help of the characteristic factor ϕ. The optimum loading of 5% TiO₂ composite membrane has shown the maximum characteristic factor.     

Novel proton-conductive nanochannel membranes with modified SiO2 nanospheres for direct methanol fuel cells

A novel approach is proposed to prepare a proton-conductive nanochannel membrane based on polyvinylidene difluoride (PVDF) porous membrane with modified SiO₂ nanospheres. The hydrophilic PVDF porous membrane with a 450-nm inner pore size was chosen as the supporting structure. Pristine SiO₂ with a uniform particle size of 95–110 nm was synthesized and functionalized with –NH₂ and –COOH, respectively. Through-plane channels of porous membrane and arranged functional nanoparticles in pores could contribute to constituting efficient proton transfer channels. The characteristics such as morphology, thermal stability, water uptake, dimensional swelling, proton conductivity and methanol permeability as proton exchange membranes, of the SiO₂ nanospheres, and the composite membrane were investigated. The formation of ionic channels in membrane enhanced the water uptakes and proton conduction abilities of the composite membranes. PVDF/Nafion/SiO₂–NH₂ exhibited superior proton conductivities (0.21 S cm^?1) over other samples due to several proton sites and the acid–base pairs formed between –NH₂ and –SO₃H. Furthermore, all the composite membranes exhibited improved methanol resistance compared with Nafion. Therefore, such a design based on porous membrane provided feasibility for high-performance proton exchange membrane in fuel cell applications.     

Preparation and properties of Nafion/hollow silica spheres composite membranes

In present work, hollow silica spheres (HSS)/Nafion^® composite membranes were prepared by solution casting. The thermal properties, water retention, swelling behavior and proton conductivity of the composite membranes were explored. It was found that HSS dispersed well at micrometer scale in the obtained composite membranes by SEM and TEM observation. Thermal properties of composite membranes were improved than that of recast Nafion^® membrane. Compared with the recast Nafion^® membrane, the composite membranes showed higher water uptake and lower swelling degree at the temperature range from 40 to 100 °C. At the same HSS loading, the smaller the diameter of HSS in composite membranes, the more the water uptake, however, the swelling degree of composite membranes was increased. The proton conductivity of the composite membrane with 3–5 wt.% HSS (120 and 250 nm) increased distinctively at above 60 °C, reached the optimal value at 100 °C, and decreased slowly when the temperature exceeded 100 °C.     

Electric field processing to control the structure of poly(vinylidene fluoride) composite proton conducting membranes

A novel method is reported for controlling the structure of poly(vinylidene fluoride) (PVdF) composite proton conducting membranes. When proton conducting Nafion or zirconium phosphate sulfophenylenphosphonate (ZrPSPP) particles are dispersed in a mixed colloidal suspension with PVdF particles, the proton conducting particles selectively respond to an applied electric field. Under appropriate conditions, the proton conducting particles are induced to assemble into chains that rapidly grow to span the gap between electrodes as the electric field is applied. By removing the solvent and melting the PVdF phase while applying the electric field, composite membranes were formed that have field-induced structure. In comparison to randomly structured composites, the electric field-processed Nafion/PVdF or ZrPSPP/PVdF composite membranes showed improved proton conductivity, water sorption, selectivity for protons over methanol, and controlled surface area changes upon swelling with water. The transport and mechanical properties of the electric field-processed composite membranes suggest the potential for improved performance in direct methanol fuel cells.     

Studies on sulfonic acid functionalized hollow silica spheres/Nafion® composite proton exchange membranes

In this work, sulfonic acid functionalized hollow silica spheres (SAFHSS)/Nafion® composite membranes were prepared by a recasting procedure. The influences of temperature on water uptake, swelling degree, and proton conductivity of the composite membranes were studied. In comparison with the pure recast Nafion® membrane, it was found that water uptake of composite membranes increased with increasing SAFHSS loading at all temperature studied. The swelling degree of SAFHSS/Nafion® composite membranes with 10～15 wt % SAFHSS loading was lower than that of the pure recast Nafion® at all temperatures in the study. The proton conductivity of SAFHSS/Nafion® composite membranes was constantly higher than that of the pure recast Nafion® at all temperatures (50～130 °C). In a range from 50 to 130 °C, the highest conductivity of composite membranes was obtained when 10 wt % SAFHSS was loaded. The maximum conductivity reached 0.1 S cm^?1 at 100% relative humidity and 100 °C, even the temperature reached to 130 °C, the conductivity of the composite membranes with 10 wt % SAFHSS was still as high as 4.4 × 10^?2 S cm^?1 at 100% relative humidity, whereas the conductivity of the pure recast Nafion® was only 2.2 × 10^?3 S cm^?1. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2647–2655, 2009     

Transport properties of composite membranes containing silicon dioxide and Nafion

Silicon dioxide (SiO₂) nanoparticles were incorporated into Nafion 115 membranes using the sol–gel method in order to investigate their effect on water retention/transport, proton concentration, effective proton mobility, and proton conductivity. By adjusting the sol–gel reaction time, Nafion/SiO₂ membranes were fabricated with SiO₂ content ranging from 5.9 to 33.3 wt%. Because the density of the membranes decreased with increasing SiO₂ content and because dimensional changes with swelling in water of the composite membranes were less than that of unmodified Nafion 115 despite having increased water content, the theory that rigid scaffolding is formed inside the membrane is supported. Water content increases with increasing SiO₂ content due to void space formed inside the membrane. This increase in water content dilutes the protons in the membrane leading to lower proton concentration and therefore lower proton conductivity. A decreasing effective proton mobility with increasing SiO₂ content, likely due to an increase in the tortuosity of the proton-conducting pathway, also contributes to the decreasing conductivity. However, as evidenced by the similar water vapour permeance values, the SiO₂ nanoparticles do not increase the effective tortuosity of the water vapour transmission pathways.     

Enhanced proton conductivity of polymer electrolyte membrane doped with titanate nanotubes

Nafion-titanate nanotubes composite membranes were prepared through a casting process. With the addition of 5 wt.%, the nanotubes were homogenously distributed in Nafion solution. The formed composite membrane showed a comparable mechanical strength to Nafion membrane. The proton conductivity of the composite membrane without external humidification is higher than that of the Nafion membrane, reaching 0.034 Scm^?1 and 0.01 Scm^?1 at 100 °C and 120 °C, respectively. The improved proton conductivity was attributed to the great water retention ability of the doped nanotubes.     

Self-assembled polyelectrolyte multilayered films on Nafion with lowered methanol cross-over for DMFC applications

The paper is concerned with the deposition of self-assembled polyelectrolyte multilayer on Nafion membrane by layer-by-layer (LbL) technique with lowered methanol cross-over for direct methanol fuel cell (DMFC) applications. The formation of self-assembled multilayered film on Nafion was characterized by UV–vis spectroscopy and it was found that the polyelectrolyte layers growth on the Nafion surface regularly. Furthermore, the proton conductivity and methanol cross-over measurements were carried out for characterization of the LbL self-assembled composite membranes. The results showed that the concentration and pH of the polyelectrolytes significantly affect the proton conductivity and methanol barrier properties of the composite membranes. 10⁻¹ monomol polyelectrolyte concentration and pH 1.8 was found to be optimum deposition conditions considering proton conductivity and methanol permeation properties of the LbL self-assembled composite membranes. The methanol permeability of the 10 bi-layers of PAH1.8/PSS1.8 deposited LbL self-assembly composite membrane was significantly suppressed and found to be 4.41 × 10⁻⁷ cm²/s while the proton conductivity value is in acceptable range for fuel cell applications.     

Preliminary evaluation of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid composite membranes for direct methanol fuel cell applications

A series of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid (SPEEK/MEA/AA) composite membranes are prepared and investigated to assess their possibility as proton exchange membranes in direct methanol fuel cells (DMFCs). A preliminary evaluation shows that introducing MEA and AA into SPEEK matrix decreases the thermal stability of membrane. However, the degradation temperatures are still above 260 °C, satisfying the requirement for fuel cell operation. Compared with the pure SPEEK membrane, the composite membranes exhibit not only lower water uptake and swelling ratios but also better mechanical property and oxidative stability. Noticeably, the methanol diffusion coefficient of the composite membranes decrease significantly from 3.15 × 10^?6 to 0.76 × 10^?6 cm²/s with increasing MEA and AA content, accompanied by only a small sacrifice in proton conductivity. Although both the methanol diffusion coefficient and the proton conductivity of composite membranes are lower than those of pure SPEEK and Nafion® 117 membranes, their selectivity (conductivity/methanol diffusion coefficient) are higher. In addition, the composite membranes show excellent stability in aqueous methanol solution. The good thermal and chemical stability, low swelling ratio, excellent mechanical property, low methanol diffusion coefficient, and high selectivity make the use of these composite membranes in DMFCs quite attractive. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2871–2879, 2007     

磺化聚芳醚砜/磺化聚酰亚胺复合质子交换膜的制备与性能研究

利用溶液浇铸法制备了一系列双磺化型磺化聚芳醚砜/磺化聚酰亚胺(SPAES/SPI)复合质子交换膜.扫描电子显微镜(SEM)结果显示复合膜不存在明显的相分离,表明二者具有很好的相容性.由于SPI的引入,复合膜在甲醇中稳定性较纯SPAES具有大幅的提高,比Nafion112低得多的甲醇吸收率表明了这些复合膜具有比后者更低的甲醇透过率.复合膜显示了与单组分膜相类似的高温分解稳定性,磺酸基团的分解温度达到了290℃以上.复合膜显示出远高于纯SPAES膜的尺寸稳定性能,在130℃高温中200h处理后,所有的复合膜均保持了高的机械性能,而此时纯SPAES膜已经溶解于水中.而且由于两种磺化聚合物间的复合,复合膜维持了较高的IEC水平,显示了较高的质子导电率,在80%相对湿度时的质子导电率与Nafion112相近,而在水中的质子导电率均高于Nafion112.     

Preparation and characterization of sulfonated poly(phenylene oxide) proton exchange composite membrane doped with phosphosilicate gels

A new class of proton exchange composite membranes made by incorporating phosphosilicate gels into SPPO matrix was prepared and characterized. The thermal stability was evaluated by TGA and DSC, and the amorphous structure information was provided from XRD. The experimental results showed that the composite membranes have good stability to oxidation by Fenton's reagent test, and the membrane dimension is hardly changed, even at high temperature. The hydration number values of the persulfonic acid group of composite membranes were lower than that of Nafion 112 at room temperature, but the water uptake of composite membranes at 80°C was higher than that of Nafion 112. With increasing relative humidity and doping amount, the conductivity of the composite membranes increased. Moreover, the conductivities of water-equilibrated composite membranes were higher than that of Nafion 112 (0.0871 S/cm) at room temperature, and the highest conductivity for the composite membrane was 0.216 S/cm. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

磺化聚醚醚酮与壳聚糖共混制备直接甲醇燃料电池用质子交换膜

给出了不同磺化度下的磺化聚醚醚酮(SPEEK)用作质子交换膜的一系列性能,另外提出了一种新型的酸碱共混质子交换膜,其中,磺化聚醚醚酮和壳聚糖分别被选为酸性、碱性高分子电解质,并对所制备的质子交换膜的相关性能如质子传导性,甲醇渗透性,吸水率以及膜溶胀性、热稳定性等进行了表征,结果表明此种新型复合膜尽管在质子传导性能方面有所下降,阻醇性能改变不大,但是膜溶胀性和吸水率方面有了较大的改善.磺化度为71.4%的SPEEK与壳聚糖以5∶1摩尔比共混制备的质子交换膜,其性质可以与商品化的Nafion 117相媲美,有望在甲醇燃料电池中得到应用.     

Novel method for the preparation of ionically crosslinked sulfonated poly(arylene ether sulfone)/polybenzimidazole composite membranes via in situ polymerization

A series of ionically crosslinked composite membranes were prepared from sulfonated poly(arylene ether sulfone) (SPAES) and polybenzimidazole (PBI) via in situ polymerization method. The structure of the pristine polymer and the composite membranes were characterized by FT-IR. The performance of the composite membranes was characterized. The study showed that the introduction of PBI led to the reduction of methanol swelling ratio and the increase of mechanical properties due to the acid–base interaction between the sulfonic acid groups and benzimidazole groups. Moreover, the oxidative stability and thermal stability of the composite membranes were improved greatly. With the increase of PBI content, the methanol permeability coefficient of the composite membranes gradually decreased from 1.59 × 10⁻⁶ cm²/s to 1.28 × 10⁻⁸ cm²/s at 30 °C. Despite the fact that the proton conductivity decreased to some extent as a result of the addition of PBI, the composite membrane with PBI content of 5 wt.% still showed a proton conductivity of 0.201 S/cm at 80 °C which could actually meet the requirement of proton exchange fuel cell application. Furthermore, the composite membranes with PBI content of 2.5–7.5 wt.% showed better selectivity than Nafion117 taking into consideration the methanol swelling ratio and proton conductivity comprehensively.     

侧链型磺化聚芳醚酮/磺化聚乙烯醇复合型直接甲醇燃料电池用质子交换膜

通过溶液共混法制备了不同磺化聚乙烯醇(SPVA)含量的侧链型磺化聚芳醚酮/磺化聚乙烯醇(S-SPAEK/SPVA)复合膜. 应用红外光谱(FTIR)对复合膜进行了表征, 扫描电镜(SEM)显示SPVA均匀分布在复合膜中. 通过对复合膜的性能测试发现该系列复合膜具有良好的热性能、较高的吸水率和保水能力. SPVA中的羟基能有效地阻碍甲醇的透过, 甲醇渗透系数从S-SPAEK/SPVA5 复合膜的7.9×10^-7 cm²·s^-1降低到S-SPAEK/SPVA30的1.3×10^-7 cm²·s^-1, 比S-SPAEK膜的11.5×10^-7 cm²·s^-1降低了一个数量级. SPVA的引入增加了亲水基团数量, 增加了复合膜的吸水和保水能力, 有利于质子按照“Vehicle”机理和“Grotthuss”机理进行传递, 柔软的SPVA链段与S-SPAEK侧链聚集成亲水相区, 形成连续的质子传输通道, 提高了复合膜的质子传导率. 在25 和80℃ 时, S-SPAEK/SPVA30 复合膜的质子传导率分别达到了0.071 和0.095 S·cm^-1. 可见,S-SPAEK/SPVA复合膜有望在直接甲醇燃料电池中得到应用.     

Phosphoric acid‐doped imidazolium ionomers with enhanced stability for anhydrous proton‐exchange membrane applications

Phosphoric acid‐doped crosslinked proton‐conducting membranes with high anhydrous proton conductivity, and good chemical stability in phosphoric acid were synthesized and characterized. The synthetic procedure of the acid‐doped composite membranes mainly involves the in situ crosslinking of polymerizable monomer oils (styrene and acrylonitrile) and vinylimidazole, and followed by the sulfonation of pendant imidazole groups with butanesultone, and further doped with phosphoric acid. The resultant phosphoric acid‐doped composite electrolyte membranes are flexible and show high thermal stability and high‐proton conductivity up to the order of 10^?2 S cm^?1 at 160 °C under anhydrous conditions. The phosphoric acid uptake, swelling degree, and proton conductivity of the composite membranes increase with the vinylimidazole content. The resultant composite membranes also show good oxidative stability in Fenton's reagent (at 70 °C), and quite good chemical stability in phosphoric acid (at 160 °C). The properties of the prepared electrolyte membranes indicate their promising prospects in anhydrous proton‐exchange membrane applications. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013 , 51, 1311–1317     

Characterizations and stability of polyimide-phosphotungstic acid composite electrolyte membranes for fuel cell

Organic-inorganic composite membranes from partially aliphatic sulfonated polyimides and heteropolyacids (HPAs) were synthesized. A series of composite membranes with varying amounts of heteropolyacid were prepared by altering the weight ratio of polyimide and HPA. The partially aliphatic sulfonated polyimides are synthesized from 1,4,5,8-naphthalenetetracarboxylic dianhydride, 4,4′-diaminobiphenyl 2,2′-disulfonic acid as the sulfonated diamine, and decamethylenediamine as the aliphatic diamine. The incorporation of HPA is confirmed by FT-IR analyses. When appropriately embedded in a hydrophilic polymer matrix, the hydrated HPAs are expected to endow the composite membrane with their high proton conductivity, while retaining the desirable mechanical properties of the polymer film. These composite membranes were evaluated for thermal stability, ion exchange capacity, water uptake and proton conductivity. Also the extraction of HPA from the polyimide membranes and their stability in water were determined. Though water uptake and IEC decreased with increase in HPA content, the proton conductivity of the composite membranes increased with increase in HPA weight content. This study shows that partially aliphatic sulfonated polyimide composite membranes with HPA can be a viable substitute for Nafion^® for fuel cells which show good conductivity comparable to Nafion^®117 at temperatures nearing 100 °C, keeping in mind that polyimides have good thermal stability and low cost.     

Surface modified multi‐walled carbon nanotubes and Nafion nanocomposite membranes for use in fuel cell applications

The preparation and characterization of the nanocomposite polyelectrolyte membranes, based on Nafion, sulfonated multi‐walled carbon nanotubes (MWCNT‐SO₃H) and imidazole modified multi‐walled carbon nanotubes (MWCNT‐Im), for direct methanol fuel cell applications is described. The results showed that the modification of multi‐walled carbon nanotubes (MWCNT) with proton‐conducting groups (sulfonic acid groups or imidazole groups) could enhance the proton conductivity of the nanocomposite membranes in comparison to Nafion 117. Regarding the interactions between the protonated imidazole groups, grafted on the surface of MWCNT, and the negatively charged sulfonic acid groups of Nafion, new electrostatic interactions can be formed in the interface of the Nafion and MWCNT‐Im, which result in both lower methanol permeability and higher proton conductivity. The physical characteristics of these manufactured nanocomposite membranes were investigated by thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, water uptake, methanol permeability, and ion exchange capacity, as well as proton conductivity. The Nafion/MWCNT‐Im membranes showed the higher proton conductivity, lower methanol permeability, and, as a consequence, a higher selectivity parameter in comparison to the neat Nafion or Nafion membrane containing MWCNT‐SO₃H or ─OH functionalized multi‐walled carbon nanotubes (MWCNT‐OH) membranes. The obtained results indicated that the Nafion/MWCNT‐Im membranes could be used as efficient polyelectrolyte membranes for direct methanol fuel cell applications.