Uniaxial tensile tests and dynamic mechanical analysis of satin weave reinforced epoxy shape memory polymer composite

The utilization of epoxy shape memory polymer composite (SMPCs) as engineering materials for deployable structures has attracted considerable attention in recent decades due to high strength and satisfactory stiffness in comparison with shape memory polymers (SMPs). Knowledge of static and dynamic mechanical properties is essential for analyzing structural behavior and recovery properties, especially for new epoxy SMPCs. In this paper, a new weave reinforced epoxy shape memory polymer composite was prepared with satin weave technique and resin transfer molding technique. Uniaxial tensile tests and dynamic mechanical analysis were carried out to obtain basic mechanical properties and glass transition temperatures, respectively.The tensile strength and breaking elongation of warp specimens were comparable with those of weft specimens. The increment of elastic modulus and hysteresis loop areas became smaller with loading cycles, meaning that cyclic tests could obtain approximate stable mechanical properties. For dynamic mechanical properties, glass transition temperature (T_g) obtained from storage modulus curves was lower than that determined from tan delta curves and T_gs in the warp and weft directions were similar (29.4 °C vs 29.7 °C). Moreover, the storage modulus in response to T_g was two orders of magnitude less than that with respect to low temperature, which demonstrated the easy processibility of epoxy SMPCs near glass transition temperature. In general, this study could provide useful observations and basic mechanical properties of new epoxy SMPCs.     

Effects of temperature and stress on creep properties of ethylene tetrafluoroethylene (ETFE) foils for transparent buildings

Creep properties of ethylene tetrafluoroethylene (ETFE) foils are indispensable for evaluating serviceability limit state, especially under high temperature and high stress. This paper concerned temperature and stress effects on creep properties of ETFE foils with experimental and theoretical studies. Experimental results showed that dimensionless stress effect on creep properties could be higher than that of temperature effect. A unified equation incorporating temperature, stress and time based on experimental results was determined and could be utilized to calculate the stress limits and long-term creep strains. The stress limits in response to creep strain of 10% were less than 5 MPa, 4 MPa and 3 MPa for temperature ranges of 40–50 °C, 50–60 °C and 70–80 °C, respectively. The long-term creep strain of ETFE foils under 40 °C was 5.96% concerning 50-year working time.Master curves of ETFE foils were evaluated considering time-temperature superposition (TTSP) and time-stress superposition (TSSP). Long-term creep strains with these master curves were identified and compared with experimental creep strains. It is found that TTSP could be a little underestimation of creep strains while TSSP could overestimate creep strains to some extent. Moreover, the maximum creep strain difference was only 0.48%, which justified the feasibility and suitability of using the unified equation to predict creep strains of ETFE foils.     

Carbon-fibre epoxy prepreg (CFC) curing in an autoclave analogue process controlled by Dynamic Mechanical Analysis (DMA)

Carbon fibre prepregs have found widespread application in lightweight constructions. They are based on a carbon-fibre fabric impregnated with reactive epoxy resin. DMA measurements under temperature conditions similar to an autoclave programme were carried out using commercially available prepreg material with a high glass transition temperature. The characteristic of the temperature programme was a dynamic heating segment at 1.5 K/min followed by a longer isothermal segment at 180 °C. The courses of the storage modulus E′, loss modulus E″ and tanδ were recorded. The measuring frequency was varied between 1 Hz and 33.3 Hz. Gelation and vitrification are assigned. The influence of the measuring frequency on the time to vitrification and the correlation with DSC are discussed. The reaction does not end even after 10 h curing at 180 °C, which is interpreted as the slow cessation of the reaction caused by vitrification.     

Mechanical properties of anion exchange membranes by combination of tensile stress–strain tests and dynamic mechanical analysis

The thermomechanical properties of anion exchange polymers based on polysulfone (PSU) quaternized with trimethylamine (TMA) or 1,4‐diazabicyclo[2.2.2]octane (DABCO) and containing hydroxide or chloride anions by tensile stress–strain tests and dynamic mechanical analysis (DMA) have been determined. The reported mechanical properties included the Young's modulus, tensile strength, and elongation at break from tensile tests and the storage and loss modulus and glass transition temperature from DMA. The anion exchange membranes behaved as stiff polymers with Young's modulus in the order of 1 GPa, relatively with high strength (about 30 MPa) and low elongation at break (around 10%) was observed. Tensile tests were also made with membranes exchanged with hydrogen‐carbonate and carbonate anions to control the absence of important carbonation of the OH form. The glass transition temperatures were of the order of 150 °C (PSU‐TMA) or 200 °C (PSU‐DABCO) for the hydroxide form, confirmed by differential scanning calorimetry; they increase further by about 50 K, when hydroxide ions are replaced by chloride. This result and the increase of the storage modulus could be interpreted by the higher hydration of hydroxide ions and the plasticizing effect of water, which reduced the Van der Waals interactions between the macromolecular chains. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1180–1187     

Thermal Properties of Salt and Base Forms of Chitosan

The temperature dependences of elastic and relaxation properties of films of salt and base forms of chitosan were obtained by methods of dynamic mechanical analysis. It was estimated that the presence of two maxima on the temperature dependence of mechanical loss tangent tanδ at T₁ = 150–160°C and T₂ = 250–270°C is typical of the salt form of chitosan. The maximum at 150–160°C on tanδ curves is reduced or even eliminated after thermal or alcohol–alkali treatment of chitosan acetate films, while the high-temperature maximum is preserved. The results of IR spectroscopy and thermogravimetric analysis allow supposing that the low-temperature maximum of molecular mobility in films of chitosan salt form is related to the removal of absorbed water and residues of acetic acid as well as to dehydration of macromolecules. The maximum at 259°C determines the glass transition temperature of the chitosan base form.     

Thermal and mechanical characteristics of polyurethane/curaua fiber composites

Polyurethane composites reinforced with curaua fiber at 5, 10 and 20% mass/mass proportions were prepared by using the conventional melt-mixing method. The influence of curaua fibers on the thermal behavior and polymer cohesiveness in polyurethane matrix was evaluated by dynamic mechanical thermal analysis (DMTA) and by differential scanning calorimetry (DSC). This specific interaction between the fibers and the hard segment domain was influenced by the behavior of the storage modulus E′ and the loss modulus E″ curves. The polyurethane PU80 is much stiffer and resistant than the other composites at low temperatures up to 70°C. All samples were thermoplastic and presented a rubbery plateau over a wide temperature range above the glass transition temperature and a thermoplastic flow around 170°C.     

Determination of the activation energies for α and β transitions of a system containing a diglycidyl ether of bisphenol a (DGEBA) and 1,3-bisaminomethylcyclohexane (1,3-BAC)

Using dynamic mechanical analysis (DMA) we have studied the variation with the frequency of the dynamic mechanical properties (storages modulus,E'; loss modulus,E'' and loss tangent or tan σ) for a system containg a diglycidyl ether of bisphenol A (DGEBA) and 1,3-bisaminomethylcyclohexane (1,3-BAC). These properties were measured both in the glass transition and β transition regions. An increase in frequency caused a shift of tan σ peak positions in both regions toward higher temperature. Finally, we report the activation energies of a DGEBA/1,3-BAC expoxy system for α and β transitions.     

Thermomechanical investigation of a thick film of aniline-formaldehyde copolymer and poly(methyl methacrylate)

A thick film of aniline-formaldehyde copolymer and PMMA is synthesized via dispersion of aniline-formaldehyde copolymer powder as filler particles in PMMA with two different concentrations. Variation of the complex elastic modulus and mechanical loss factor (tanδ) with temperature is studied. It is observed that the complex elastic modulus decreases with temperature owing to thermal expansion of films. On the other hand, tanδ increases up to a characteristic temperature beyond which it shows a decreasing trend toward melting. Transition temperature T _g of sample S₁ (pure PMMA) is found to be 80°C. In sample S₂ (1 wt % aniline formaldehyde copolymer), the peak of tanδ at a lower temperature (66°C) corresponds to glass transition temperature T _g of the PMMA matrix, while the peak of tanδ at a higher temperature (107.8°C) corresponds to T _g of a polymer chain restricted by filler particles of aniline-formaldehyde copolymer. A further increase (10 wt % aniline-formaldehyde copolymer) in the concentration of filler particles of aniline-formaldehyde copolymer results in a more compact structure and a shift of T _g to a higher temperature, 122.2°C. This shift in the glass transition temperature of thick films of aniline-formaldehyde copolymer and PMMA is dependent upon the concentration of filler particles in the sample.     

非交联组份对端乙烯基聚环氧丙烷/聚苯乙烯网状共聚物粘弹性的影响

本文描述了端乙烯基聚环氧丙烷/聚苯乙烯网状共聚物的合成及表征。研究了非交联组份对共聚物的玻璃化转变温度T_g,贮能模量E'、耗能模量E'和阻尼系数tanδ等动态力学性能的影响,计算了试样的粘弹性参数。结果表明,非交联组份对交联网有明显塑化作用,使其T_g降低,自由体积分数和阻尼系数增大。     

The effect of fiber orientation and stacking sequence on carbon/E-glass/epoxy intraply hybrid composites under dynamic loading conditions

This study investigated the dynamic mechanical properties of hybrid intraply carbon/E-glass epoxy composites with different orientations and stacking sequences under different loading conditions with increasing temperature. A neat epoxy and five various hybrid composites such as Carbon (0°)/E-glass (90°), Carbon (45°)/E-glass (135°), Carbon (90°)/E-glass (0°), Carbon/E-glass (alternating layer), and Carbon/E-glass (alternating layer 45°) were manufactured. Three-point bending test and dynamic mechanical test were conducted to understand the flexural modulus and viscoelastic behavior (storage modulus, loss modulus, and loss tangent) of the composites. Dynamic mechanical test was performed with the dual cantilever method, at four different frequencies (1, 5, 10, and 20 Hz) and temperatures ranging from 30 to 150°C. The experimental results of storage modulus, loss modulus, and loss tangents were compared with the theoretical findings of neat epoxy and various hybrid composites. The glass transition temperature (T_g) increased with the increase in frequency. A linear fit of the natural log of frequency to the inverse of absolute temperature was plotted in the activation energy estimation. The interphase damping (tanδ_i) between plies and the strength indicator (S_i) of the hybrid composites were estimated. It was observed that the neat epoxy had more insufficient storage and loss modulus and a high loss tangent at all the frequencies whereas hybrid composites had high storage and loss modulus and a low loss tangent for all the frequencies. Compared with other hybrid composites, Carbon (90°)/E-glass (0°) had higher strength and activation energy. The result of reinforcement of hybrid fiber in neat epoxy significantly increases the material's strength and stability at higher temperatures whereas decreasing free molecular movement.     

Monitoring the glass transition temperature of polymeric composites with carbon nanotube buckypaper sensor

Carbon nanotube (CNT) Buckypapers can be infused with resin and easily incorporated into conventional fiber reinforced composites. In this paper, we propose to use Buckypaper (BP) as a new measuring method to determine the glass transition temperature of polymeric composites. The CNT-only BP was fabricated by spray-vacuum filtration method with monodispersion of multi-wall carbon nanotubes, and then co-cured with polymeric composites. After manufacturing, the glass transition temperature of polymeric composites could be obtained from the relationship between resistance and temperature of BP during the dynamic heating process. Experimental results show that the glass transition temperature of composite samples A and B monitored by BP sensors were 127 °C and 180 °C, while such temperatures obtained from a dynamical mechanical analyzer (DMA) were 128 °C and 184 °C respectively. This paper not only reveals the ability of BP as a sensor for monitoring the glass transition temperature of composite but also provides a new way to understand the glass transition phenomenon of composite.     

Thermal behavior of aromatic polyamic acids and polyimides containing oxadiazole rings

Two aromatic polyimides and the corresponding poly(amic acid)s, with oxadiazole and para/meta phenoxyphenylene rings in the backbone, were synthesized and the structure — thermal properties correlation was followed by dynamic mechanical analysis. Concerning the poly(amic acid)s, the glass transition domain was emphasized only for the compound with meta-oriented rings because the process of imidization takes place with increasing temperature. A multiplex experiment was performed to calculate the activation energy of the transition localized under 200°C. Consecutive heating-cooling-heating cycles were accomplished. All phenomena are discussed by cross-examination of the storage modulus (E′), loss modulus (E″) and loss factor tanδ variation with temperature.     

Poly(vinylidene fluoride)/clay nanocomposites prepared by melt intercalation: Crystallization and dynamic mechanical behavior studies

The preparation and properties of poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported for the first time. PVDF/clay nanocomposites were prepared by melt intercalation with organophilic clay. The composites were characterized with X‐ray diffraction, differential scanning calorimetry, and dynamic mechanical analysis. X‐ray diffraction results indicated intercalation of the polymer into the interlayer spacing. PVDF in the nanocomposites crystallized in the β form. Differential scanning calorimetry nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity, as evidenced by the melting and crystallization peaks. Isothermal crystallization studies showed an enhanced rate of crystallization with the addition of clay, as evidenced by a reduction in the crystallization time. Dynamic mechanical analysis indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. The tan δ peak signifying the glass‐transition temperature of PVDF shifted to higher temperatures. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1682–1689, 2002     

Thermal analysis of ring‐opening metathesis polymerized healing agents

Dicyclopentadiene (DCPD) and 5‐ethylidene‐2‐norbornene (ENB) and their mixtures were analyzed after ring‐opening metathesis polymerization (ROMP) in the presence of Grubbs catalyst as potential candidate healing agents for self‐healing composite materials using two complementary methods, rotational dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). Following isothermal DMA measurements at room temperature (RT = 25 °C) for 120 min, two consecutive dynamic temperature scan experiments were performed for each system. In the first dynamic temperature scans, there was an initial downward peak slightly above RT in the storage modulus versus temperature curve for samples with relatively slower reaction rates (i.e., DCPD and DCPD‐rich mixtures or low catalyst loadings) due to a combination of the glass transition followed by further residual reaction. However, no or negligible downward peaks were observed for the highly reactive ENB and ENB‐rich samples even at much lower catalyst loadings. Implications of the substantial decrease in storage modulus just above RT for the slowly reacting systems are discussed for healing of damage in composite materials at elevated temperatures. The maximum glass transition temperatures (T_g∞) from DMA of the fully cured samples were determined to be approximately 160 °C for DCPD and 120 °C for ENB, decreasing linearly with increased ENB in the blends. The glass transitions and further residual reactions above the glass transitions were confirmed by DSC. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1771–1780, 2007     

Aging and cold crystallization of melt‐extruded poly(trimethylene terephthalate) films

We analyzed the thermal crystallization, glass‐transition behavior, and mechanical properties of melt‐extruded poly(trimethylene terephthalate) (PTT) films to investigate their physical aging and annealing effects. The physical aging and annealing of PTT films had an influence on the glass‐transition temperature, recrystallization behavior, and mechanical properties. When samples were aged at an ambient temperature, the crystallization temperature decreased largely within 5 h, the heat of crystallization increased, and the breaking stress and breaking elongation increased. The glass‐transition temperature of annealed samples, which was obtained from differential scanning calorimetry and dynamic mechanical measurements, increased with increasing annealing temperature below 80 °C but decreased above that temperature. In addition, the glass‐transition temperature and modulus of annealed samples were largely affected by the annealing time; in particular, they increased sharply within 1 h on annealing at 50 °C. Consequently, the change in the glass‐transition temperature on annealing was ascribed to the fact that the molecular constraint due to recrystallization and the mobility of rigid amorphous PTT chains competed with each other, being dependent on the annealing temperature. The mechanical properties of aged samples were closely related to their cold‐crystallization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1920–1927, 2001     

Epoxy shape memory polymer (SMP): Material preparation,uniaxial tensile tests and dynamic mechanical analysis

The utilization of epoxy shape memory polymers (SMPs) as engineering materials for deployable structures has attracted considerable attention due to their excellent thermo-mechanical endurance and satisfactory processability. Knowledge of static and dynamic mechanical properties is essential for analyzing structural behavior and recovery, especially for new epoxy SMPs. In this paper, a new epoxy SMP was prepared with epoxy and aromatic amine curing agent. Uniaxial tensile tests and digital image correlation were used to obtain static mechanical properties. Dynamic mechanical analysis was carried out to evaluate glass transition temperatures that corresponded to the heat in the recovery process.It was found that elastic modulus, Poisson’s ratio and shear modulus are 1413 MPa, 0.35 and 591 MPa, respectively. The beginning of glass transition temperature of 37.4 °C could be effectively achieved by electrical heaters, validating the shape memory properties of epoxy SMPs. In general, this study could provide useful observations and basic mechanical properties of epoxy SMPs.     

Dynamic mechanical and dielectric properties of epoxidized SBS triblock copolymer

The morphological and dynamic properties of epoxidized styrene–butadiene–styrene block copolymers were studied and compared with their parent styrene–butadiene–styrene block copolymer (SBS). Two peaks were observed in the mechanical loss (tan δ) curve which can be attributed to segmental motion of epoxidized polybutadiene (EPPB) and polystyrene. Analysis by DSC thermograms also showed the linear increase of glass transition temperature for EPPB domain with the epoxy group content. Phase separated structures of epoxidized SBS as observed by TEM suggests a considerable degree of mixing occurred between phases after 80 mol % of the double bonds in SBS were epoxidized. The interfacial region displays a third peak and causes much steeper drop in modulus at higher temperature than T_g of EPPB. Parallel dielectric relaxation measurements were also made in the frequency range of 30 Hz–1 KHz as a function of temperature. In each dielectric constant (?′) curve, there is a maximum near the T_g of EPPB determined from the dielectric loss tangent curve. The shift in T_g of EPPB versus epoxy group content was consistent with that measured by the thermal and dynamic mechanic analysis. These findings indicated an 8°C shift in glass transition temperature as the epoxy group content in EPPB increased 10%.     

Study of a plasticized‐unoriented P(VF2/VF3) (73/27 mol%) copolymer. I. The effects of crystallization conditions on morphology,physical, and thermal properties

The results of a study on the effects of a plasticizer, tricresyl phosphate, on the mechanical and thermal properties of unoriented films of poly(vinylidene fluoride–trifluoroethylene) (VF₂/VF₃) copolymer (73/27 mol%) are presented. Films were prepared by both quenching and slow‐cooling from the melt with plasticizer concentrations of 0, 5, and 10% by weight. For the slow‐cooled films, a reduction in crystallinity by 25% was observed for the heavily plasticized films, together with a reduced dynamic mechanical modulus (≈ 58%) and an increased dielectric constant (≈ 200%). For the quenched films, a small increase in crystallinity was observed together with a reduced modulus and an increased dielectric constant. Measurements of the temperature dependence of the modulus and dielectric constant at 10 Hz. were also carried out from −100°C to 100°C. This data showed that for slow‐cooled films the glass transition temperature decreased from −28°C to ‐52°C at the highest doping level. DSC thermal analysis shows a decrease in the Curie transition (≈ 4°C) and melting temperatures (≈ 9°C) for the quenched films, while the slow‐cooled films only showed a decrease in melting temperature (≈ 10°C), while the Curie transition temperature was unaffected. In addition, evidence of a two‐phase system or a nonferroelectric crystal phase is noted by the presence of two Curie transition temperature peaks. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 19–28, 1999     

Preparation,characterization, and polymerization of maleimidobenzoxazine monomers as a novel class of thermosetting resins

New series of benzoxazine‐based monomers, namely maleimidobenzoxazines, were prepared with hydroxyphenylmaleimide, formalin, and various amines (e.g., aniline, allylamine, and aminophenyl propargyl ether). The structure of the novel monomers was confirmed by IR, ¹H NMR, and elemental analysis. The monomers were easily dissolved in many common organic solvents. Differential scanning calorimetry of the novel monomers showed exotherms at different temperature ranges that corresponded to the polymerization regime of benzoxazine and maleimide along with other functionalities such as allyl or propargyl, if any. IR was studied to follow the progress of the curing reaction of maleimidobenzoxazine after various thermal treatments. The thermal cure of the monomers at 250 °C afforded a novel network structure that combined polybenzoxazine and polymaleimide. The dynamic mechanical analyses showed that the storage moduli of the thermosets derived from maleimidobenzoxazine were kept constant up to high temperatures. The glass‐transition temperatures were as high as 241–335 °C. Moreover, thermogravimetric analyses revealed that the thermosets did not show any weight loss up to about 350 °C, with char yields ranging from 62 to 70% at 800 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1424–1435, 2006     

Evaluation of interfacial region of microphase-separated SEBS using modulated differential scanning calorimetry and dynamic mechanical thermal analysis

The continuous structural changes of Poly(styrene-b-ethylene-butylene-b-styrene) [SEBS] due to the effect of temperature are hard to evaluate using conventional differential scanning calorimetry (DSC). This paper presents an accurate and simple way to evaluate microstructural and glass transitions of SEBS using modulated differential scanning calorimetry (MDSC). The weak crystalline nature of –(CH₂-CH₂)–_n in the ethylene-butylene (EB) block melted around 36 °C. The premature molecular moment and Tg of the styrene block were at 62 °C and 96 °C, respectively. The interfacial region at high temperature was explained with respect to order-order transition (OOT) at 144 °C and a prominent Order-Disorder Transition (ODT) at around 202 °C. Dynamic mechanical thermal analysis (DMTA) and dynamic mechanical rheological testing (DMRT) measurements also revealed that the T_g of the PS transition were consistent at around 96 °C.