Morphology dependence of crystallization of natural rubber in blends

Crystallization of natural rubber (NR) was investigated in different morphology for NR/styrene butadiene rubber (SBR) blend and NR/polystyrene-(b)-polyisoprene (SI)/polystyrene (PS) blend. A purified NR (PC-TE) was prepared from pale crape via transesterification. In the blends, PC-TE formed various morphologies; that is, matrix phase, island phase and continuous phase with a nano-scale, respectively, in dependence upon the ratio of the rubbers. The crystallization rate of the blends was also significantly associated with the morphology of the rubbers.     

Study on grafting of different types of acrylic monomers onto natural rubber by γ-rays

 A comparative study of various acrylic monomers for grafting onto natural rubber was done. The stability of natural rubber latex (NRL) against coagulum with monomer, mechanical properties of grafted rubbers and percent of grafting were investigated. The NRL with monomers, methylacrylate (MA), ethylacrylate (EA) and n-butylacrylate (n-BA), is unstable but it is stable with methyl methacrylate (MMA), n-butyl methacrylate (BMA) and cyclohexyl methacrylate (CHMA). The mechanical properties and degree of grafting attained a maximum at a total radiation dose of 4 kGy. The values of tensile properties of MMA and CHMA grafted rubbers are almost similar, and higher than those of BMA grafted rubbers. On the other hand, the degree of grafting for CHMA is higher than those of MMA and BMA grafted rubbers. The infrared (IR) spectra of monomer grafted natural rubber were also studied.     

Smart numerical method for calculation of simple general infrared parameter identifying binary rubber blends

In the present work, binary blends of carbon black-filled cured rubber, composed of natural rubber (NR) and styrene butadiene rubber (SBR) at three different blend ratios, were subjected to Fourier Transform Infrared (FT-IR) spectroscopic study in attenuated total reflection (ATR) mode. The objective was to use the infrared spectra obtained to calculate a simple general infrared blend parameter (P_IR), a characteristic of the NR-SBR blend. The calculation for determining P_IR required finding the exact infrared (IR) peak heights for NR and SBR, at 1375 and 699 cm⁻¹, respectively. To obtain the exact peak heights, each of the spectra originally obtained from the IR spectrophotometer was modified using a newly developed numerical algorithmic method of baseline creation on and subsequent subtraction from the original spectrum. A very good baseline fit was achieved using this method. As a result, the numerical calculation of P_IR for the NR-SBR blend was possible.     

Thermal stability of acrylonitrile/chlorosulphonated polyethylene rubber blend

The properties of chlorosulphonated polyethylene (CSM) rubber, acrylonitrile rubber (NBR) and their blend (50/50 w/w) were studied. Fourier transform infrared (FTIR) studies supported that CSM/NBR rubber blend is self curable, when cross-linking takes place between acrylonitrile groups of NBR and –SO₂Cl groups or in situ generated allyl chloride moieties of CSM. The thermal stability of vulcanizates was analyzed in nitrogen by thermogravimetry. It was found that the initial degradation temperature of elastomer based on CSM rubber is lower than of pure NBR rubber. By adding NBR to CSM rubbers, the degradation temperature of crosslinked material increased, indicating higher thermal stability. The activation energy for the degradation are determined using the Arrhenius equation The activation energies for the rubber blends are higher than for elastomers based on pure rubbers. It was found that the mass loss of the blends at any temperature was between those of the pure rubbers. The differential scanning calorimetry (DSC) was used for the glass transition temperature determination. It is estimated thermodynamic immiscibility of NBR/CSM blend based on noticed two different glass transition temperatures, corresponding to CSM and NBR rubbers.     

煤液化残渣与褐煤混煤燃烧特性的实验研究

煤液化是提高煤炭资源利用率、减轻燃煤污染的有效途径[1].在煤液化工艺过程中,煤液化残渣的主体是由液化原料煤中未转化的煤有机体、无机矿物质以及外加的液化催化剂组成,是一种高炭、高灰和高硫的物质,在某些工艺中会占到液化原煤总量的30%左右,如此多的残渣量对液化过程的热效率和经济性所产生的影响是不可低估的[2].     

Study of carbon black obtained by pyrolysis of waste scrap tyres

Waste scrap tyres were thermally decomposed under various conditions. Decompositions were followed by the TGA method. Specific heating regimes were tested to obtain optimal structural properties of resulting pyrolytic carbon black produced by pyrolysis of scrap tyres and the process was characterized in temperature interval from 380 to 1,200 °C and heating rate 10, 20 and 50 °C min^?1 under nitrogen atmosphere. The original scrap tyres and pyrolytic carbon black were characterized by Raman and Fourier transform infrared spectroscopy methods. Textural properties were also determined. Effect of temperature and heating rate on process of pyrolysis of scrap tyres was observed. Shifting of temperature of maximum pyrolysis rate to lower value and spreading of DTG peak is caused by increasing heating rate. Temperature 570 °C was sufficient for total scrap tyres pyrolysis. Graphitic and disordered structure was distinguished in the formed carbon black by Raman spectroscopy. With increasing temperature, heating rate and weight loss, the amount of the graphitic structure was reduced at the expense of disordered structure. Destruction of nonporous scrap tyres and formation of porous structure took place at higher temperature. Porous carbon black is formed above 380 °C, specific surface area increased up to 88 m² g^?1 .     

Raman spectroscopy and thermal analysis of gum and silica-filled NR/SBR blends prepared from latex system

Natural rubber/styrene-butadiene rubber (NR/SBR) blends, with and without silica, were prepared by co-coagulating the mixture of rubber latices and various amounts of well-dispersed silica suspension. An attempt to predict blend compositions was made using Raman spectroscopy in association with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was found that the intensity of each Raman characteristic peak was strongly dependent on the blend composition, but there was no significant evolution with the presence of silica. Also, TGA results revealed an improvement in thermal stability of NR/SBR blends with increasing both SBR and silica contents due to the dilution effect. Two distinct glass transition temperatures (T_g) were observed in DSC thermograms of all blends, and their T_g values were independent on both blend composition and silica content. This indicated a physical blend formation, which agreed well with no shifts in Raman peaks of the blends in comparison with those of the individual rubbers. Linear regression with R² quality factor close to 0.99 was achieved when plotting intensity ratio at 1371/1302 cm^?1 versus blend ratios. On the other hand, the peak height ratio and heat capacity ratio from TGA and DSC analysis, respectively, yielded quadratic equations as a function of blend ratios.     

Thermal characterization of biodegradable methoxy poly(ethylene glycol)-b-poly(d,l-lactide)/methoxy poly(ethylene glycol)-b-poly(ε-caprolactone) blend nanoparticles

Biodegradable methoxy poly(ethylene glycol)-b-poly(d,l-lactide) (MPEG-b-PDLL) and methoxy poly(ethylene glycol)-b-poly(ε-caprolactone) (MPEG-b-PCL) diblock copolymers were synthesized by ring-opening polymerization of DLL and CL monomers in bulk using stannous octoate, and MPEG as the initiating system. Surfactant-free MPEG-b-PDLL/MPEG-b-PCL blend nanoparticles were prepared by the nanoprecipitation method. The influences of block length and blend ratio on morphology, average size, and thermal properties of the blend nanoparticles were determined. The blend nanoparticles were spherical in shape. The average particle sizes slightly decreased as the MPEG-b-PCL blend ratio increased. ¹H-NMR and thermogravimetry revealed the different MPEG-b-PDLL/MPEG-b-PCL blend ratios of the nanoparticles. Differential scanning calorimetry showed that the MPEG-b-PCL crystallinity steadily decreased as the MPEG-b-PDLL blend ratio increased, suggesting miscible blending between the MPEG-b-PDLL and MPEG-b-PCL in the amorphous phase of the nanoparticle matrix.     

Development of novel elastomeric blends derived from chlorinated nitrile rubber and chlorinated ethylene propylene diene rubber

Chlorinated nitrile rubber (Cl-NBR) has been blended with chlorinated ethylene propylene diene rubber (Cl-EPDM) in different ratios by a conventional mill mixing method. The effect of the blend ratio on processing characteristics, mechanical properties (such as tensile and tear strength, elongation at break, hardness, abrasion resistance, heat build-up and resilience), structure, morphology, glass transition temperature (Tg), thermal stability, flame retardancy, oil resistance, AC conductivity, dielectric properties and transport behavior of petrol, diesel and kerosene were investigated. The shift in absorption bands of blends studied from FTIR spectra, single Tg from DSC analysis and decrease in amorphous nature from XRD showed the molecular miscibility in Cl-NBR/Cl-EPDM blends. SEM images showed the uniform mixing of both Cl-NBR and Cl-EPDM in a 50/50 blend ratio. The TGA curves indicated the better thermal stability of the polymer blend. The elongation at break, heat build-up, resilience and hardness of the polymer blend decreases with an increase in Cl-NBR content in the blend whereas the flame and oil resistance were increased with increase in Cl-NBR content. Among the polymer blends, the maximum torque, tensile strength, tear and abrasion resistance was obtained for the 50/50 blend ratio because of the effective interfacial interactions between the blend components. AC conductivity and dielectric properties of polymer blend increased with increase in the ratio of Cl-NBR in the blend. Different transport properties such as diffusion, permeation and sorption coefficient were measured with respect to nature of solvent and different blend ratios. Temperature dependence of diffusion was used to estimate the activation parameters and the mechanism of transport found to be anomalous.     

Physico-chemical properties of chromium trioxide and its suboxides

Seven samples of chromium suboxides of composition CrO_3-x are prepared from the thermal decomposition of CrO₃. The O/Cr ratio of each is determined by chemical analysis and ignition loss. X-Ray analysis reveals that they are more or less of the correct structure contaminated with the nearest suboxide. The specific gravity is determined pycnometrically and varies linearly with the O/Cr ratio.TGA indicates weight losses which agree with the calculated O/Cr ratio. DTA and DTG give endothermic peaks corresponding to the temperature of preparation of the successive samples.     

Effect of particle size on pyrolysis characteristics of Elbistan lignite

In this study, the relationship between particle size and pyrolysis characteristics of Elbistan lignite was examined by using the thermogravimetric (TG/DTG) and differential thermal analysis (DTA) techniques. Lignite samples were separated into different size fractions. Experiments were conducted at non-isothermal conditions with a heating rate of 10°C min⁻¹ under nitrogen atmosphere up to 900°C. Pyrolysis regions, maximum pyrolysis rates and characteristic peak temperatures were determined from TG/DTG curves. Thermogravimetric data were analyzed by a reaction rate model assuming first-order kinetics. Apparent activation energy (E) and Arrhenius constant (A _r) of pyrolysis reaction of each particle size fraction were evaluated by applying Arrhenius kinetic model. The apparent activation energies in the essential pyrolysis region were calculated as 27.36 and 28.81 kJ mol⁻¹ for the largest (−2360+2000 μm) and finest (−38 μm) particle sizes, respectively.     

Study of interactions of different rubber blends by infrared spectrophotometry using LDPE as matrix material for sample preparation

Use of LDPE as the matrix material in sample preparation for IR analysis of raw rubbers has been established earlier. In this paper different rubber blends have been analysed using the same technique. Interaction of different blend systems has been studied and probable interactions have been proposed.     

Toughening effect of ethylene‐vinyl acetate rubber on nylon 1010 compatibilized by maleated ethylene‐vinyl acetate copolymers

The toughening effect of ethylene‐vinyl acetate rubbers (EVM) with maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) on the nylon 1010 was investigated. The addition of 5 phr (per hundred nylon 1010) EVM increased the elongation at break of nylon 1010 to a great extent. The notched Izod impact strength of nylon/EVM blends increased with increasing EVM content. Scanning electron microscope showed that the EVM particle size was around 0.5 μm when the EVM content was 5 phr and increased with increasing EVM content. After the addition of EVA‐g‐MAH to nylon/EVM (100/20) blend, the average diameter of EVM particles decreased from more than 1 μm to 0.5–0.6 μm. EVA‐g‐MAH could improve the adhesion between nylon 1010 and EVM. A sharp brittle‐ductile transition (BDT) was observed when the interparticle distance was about 0.2 μm, independent of the addition of EVA‐g‐MAH. The notched Izod impact strength of nylon/EVM blends at low temperatures was measured and the BDT shifted toward low temperatures with increasing EVM or EVA‐g‐MAH content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 434–444, 2009     

Impact of rubber surface interactions on the morphology of clusters

ABSTRACT

We studied the influence of the adhesion strength of rubber chains and silica surfaces on the morphology of clusters by means of small-angle X-ray scattering experiments. We used mono- and bifunctional silanes and compare the results to untreated silica in different rubbers. We demonstrate a universal impact of the concentration on the cluster size and number of particles in agglomerates. The magnitude of the effects depends on the strength of the interactions between chains and particle surfaces. Best dispersion is obtained for bifunctional silanization.     

Studies on phase morphology and thermo-physical properties of nitrile rubber blends

The study deals with the morphological and thermal analysis of binary rubber blends of acrylonitrile-co-butadiene rubber (NBR) with another polymer. Either ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA), chlorosulphonated polyethylene (CSM), or polyvinyl chloride (PVC) has been selected for the second phase. Depending on the relative polarity and interaction parameter of the components, the binary blends showed development of a bi-phasic morphology through scanning electron microscopy (SEM). Use of different types of thermal analysis techniques revealed that these blends are generally incompatible excepting one of NBR and PVC. Derivative differential scanning calorimetry (DDSC), in place of conventional DSC, has been used to characterize the compatibility behavior of the blends. NBR–PVC shows appearance of only one glass transition temperature (T _g) averaging the individual T _g’s of the blend components. The partially missible blend of NBR and CSM shows a broadening of T _g interval between the phase components, while the immiscible blends of either NBR–EPDM or NBR–EVA do not show any change in T _g values corresponding to the individual rubbers of their blend. The experimental T _g values were also compared with those calculated theoretically by Fox equation and observed to match closely with each other. Studies have also been made to evaluate the thermal stability of these blends by thermo-gravimetric analysis (TG) and evaluation of activation energy of respective decomposition processes by Flynn and Wall method. Thermo-mechanical analysis (TMA) was found to be effective for comparison of creep recovery and dimensional stability of the blends both at sub-ambient as well as at elevated temperatures.     

FT‐IR Investigation into the miscible interactions in new materials for optical devices

In this article we determine the miscibility of azobenzene derivative (poly(4‐(N‐(2‐methacryloyloxyethyl)‐N‐ethylamino)‐4′‐nitroazobenzene)₉₀‐co‐(methyl methacrylate)₁₀)/poly(vinyl acetate) (PVAc) and azobenzene derivative/poly(vinyl chloride) (PVC) blends using Fourier Transform infrared (FT‐IR) spectroscopy. With this method we can clearly identify the exact interactions responsible for miscibility. In the azobenzene derivative 50:50PVAc blend new peaks were evident at 2960, 2890, 1237 and 959 cm^?1, these peaks depict miscible interactions. These wavenumbers indicate that the miscible interactions occurring are from the C? H stretching band, the vinyl acetate C?O, conjugated to the ester carbonyl, the cis‐transformation N?N stretch frequency and the acetate ester weak doublet. The azobenzene derivative 80:20PVC blend display peaks identical in profile to the blend homopolymers, indicating no miscible interactions. However, this could be due to overlapping of peaks within the same wavenumber region, making resolution difficult. This research demonstrates FT‐IR can deduce favorable interactions for miscibility and therefore numerous miscible blends can successfully be calculated if possessing the same groups responsible for miscibility. This paves the way for a new generation of designer optical materials with the desired properties. Copyright © 2003 John Wiley & Sons, Ltd.     

Surface modification of chlorobutyl rubber by plasma polymerization

Radio frequency (r.f.) plasma polymerization of vinylidene fluoride (CH₂CF₂) has been used to modify the surface properties of chlorobutyl rubber. FTIR-ATR spectra of the treated rubbers and transmission spectra of plasma polymer films on NaCl windows indicated that as power increased the F/H ratio decreased. SIMS tests supported the FTIR results, and showed that the decrease in the F/H ratio was due to a decrease in the amount of F and an increase in the amount of H in the plasma polymer. Sliding friction measurements showed a reduction in the coefficient of friction (μ) from 3.7 for the untreated rubber to values ranging between 0.4 and 1.9 for the plasma-treated rubbers. There did not appear to be any correlation between the coefficient of friction and plasma power or monomer flow rate, and the average coefficient of friction for the plasma-treated samples was 0.9, which was lower than a commercially used silicone oil treatment (μ = 1.1–1.3). Repetitive sliding friction tests showed that the plasma- and silicone oil treated-chlorobutyl rubbers had the similar lubricating lifetimes. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1651–1660, 1997     

Determination of bound rubber composition of filled SBR/BR blend compounds by analysis of the unbound rubber composition and bound rubber content

Analytical method for determination of the bound rubber composition of a filled SBR/BR blend compound was developed using measurement of the bound rubber content and microstructural analysis of the unbound rubber composition. Various filled SBR/BR blend compounds with different blend ratios were prepared using SBRs with different microstructures. This method included measurement of the bound rubber content, extraction of the unbound rubber, microstructural analysis of the unbound rubber composition, and process for determination of the bound rubber composition. Composition of the unbound rubber was analyzed using liquid proton nuclear magnetic resonance spectroscopy (H-NMR) and transmission Fourier transform infrared spectroscopy (FTIR). It was found that the analytical results using H-NMR had less experimental errors than those using transmission-FTIR. The raw SBR/BR blends were also analyzed in order to evaluate level of the experimental errors. Average SBR/BR ratios of the unbound rubbers were obtained using the 1,2- and 1,4-unit contents determined by the H-NMR analysis. The bound rubber compositions were obtained using the bound rubber contents and the average unbound rubber compositions. It was found that most of the bound rubbers had higher SBR ratios than the formulation value.     

Synthesis and spectroscopic studies of Mn(II), Co(II), and Cu(II) complexes of novel 2-[2,4-Dioxo-4-(thiophen-2-yl)butanamido]benzoic acid ligands

Mn(II), Co(II), and Cu(II) complexes with novel heterocyclic ligands derived from anthranilic acid and its 5-bromo derivative with ethyl-2-thionylpyruvate were synthesized and characterized by means of elemental analysis, molar conductivity, spectral methods (IR, ¹H NMR, and UV-Vis spectra) and simultaneous thermal analysis (TG and DTG) techniques. The IR spectra of the two ligands and their complexes were used to identify the type of bonding. The kinetic thermodynamic parameters such as: E*, ΔH*, ΔS*, and ΔG* were estimated from the DTG curves. New ligands and their complexes have been tested for their possible antibacterial and antifungal activity.     

Studies on the thermal decomposition of salicylhydroxamic acid and its metal complexes with Ni(II), Co(II), Fe(II), Mn(II) and Zn(II)

The thermal decomposition of salicylhydroxamic acid and its metal complexes with Ni(II), Co(II), Fe(II), Mn(II) and Zn(II) has been studied by TG, DTG, DTA and IR spectroscopy. All the compounds investigated decompose to yield intermediate N-hydroxylactams.Decomposition schemes have been proposed and reaction enthalpies and kinetic parameters have been calculated.