Development of a stability-indicating capillary electrophoresis method for norfloxacin and its inactive decarboxylated degradant

A simple, accurate, precise, rapid and sensitive stability-indicating capillary electrophoresis (CE) method was optimized and validated for the simultaneous determination of norfloxacin and its inactive decarboxylated degradant in pharmaceuticals. The univariant method was used to optimize electrophoretic factors including injection time, separation voltage and column temperature. Electrolyte concentration and pH were optimized using the factorial design and response surface methods. The optimum conditions obtained were: 10 mmol l^− 1 phosphate at pH 2.5, hydrodynamic injection time of 8 s at pressure 0.5 p.s.i., separation voltage 25 kV and column temperature 25 °C. The separation was carried out into a fused-silica capillary column (31.2 cm length × 50 μm i.d.) with detection at 301 and 285 nm for the intact drug and the degradant, respectively using a diode array detector. For both analytes, the method enjoys wide dynamic range (1-50 μg ml^− 1) with good detectability (limits of detection 0.11 μg ml^− 1). In addition, acceptable accuracy (recovery > 95%); and good repeatability and intermediate precision (RSD < 3.5%) were obtained.     

Highly efficient approach for characterizing nanometer-sized gold particles by capillary electrophoresis

This paper demonstrates that capillary electrophoresis (CE) can be employed for characterizing the sizes of nanometer-scale gold particles. We characterized the gold nanoparticles by effecting CE separation using a buffer of SDS (70 mM) and 3-cyclohexylamino-1-propanesulfonic acid (CAPS; 10 mM) at pH 11.0 and an applied voltage of 18 kV and obtained a linear relationship (R² > 0.99) between electrophoretic mobilities and size for nanoparticles whose diameters fall in the regime from 5.0 ± 0.5 to 41.2 ± 3.3 nm; the relative standard deviations of these electrophoretic mobilities are <0.8%. We evaluated the feasibility of employing these separation conditions for the size characterization by of gold nanoparticle samples that were synthesized by a rapid microwave heating method. We confirmed that this CE method is a valid one for size characterization by comparing the results obtained by CE with those provided by scanning electron microscopy (SEM); a good correlation exists between these two techniques. Our results demonstrate that CE can be employed to accelerate the analysis of the sizes of nanomaterials.     

Rapid analysis of anthracycline antibiotics doxorubicin and daunorubicin by microchip capillary electrophoresis

A simple and rapid method has been developed for the analysis of anthracycline antibiotics doxorubicin (DOX) and daunorubicin (DAU) in human serum using mirochip-based capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection. In this study, method development included studies of the effect of buffer pH, buffer concentration, organic solvents and separation voltage on sensitivity and separation efficiencies for the CE separation of DOX and DAU. Acetonitrile was found to have significantly improved the sensitivity and separation efficiency. The method was validated with regard to reproducibilities, linearity and limit of detection (LOD). The optimum electrophoretic separation conditions were 10 mM sodium tetraborate buffer at pH 9.5 with 40% acetonitrile (V/V) and a separation voltage of 2.1 kV. DOX and DAU were separated in 60 s under the optimum separation conditions. Linear relationships were obtained between the concentration and peak area (or peak height) in the 1–75 µg mL^{− 1} range and with the detection limits of 0.3 and 0.2 μg mL^{− 1} for DOX and DAU, respectively. The stability of both migration time and peak height of the analytes showed relative standard deviations of less than 5% (n = 9). The potential of this method was verified by spiking a human serum sample with the two drugs and analyzing the recovery ratios.     

Nonaqueous capillary electrophoresis conditions for the simultaneous separation of eight alpha-adrenergic blocking agents

The analysis is described for the first time for separating eight alpha-adrenergic blocking agents (oxymetazoline, 5-methylurapidil, prazosin, phentolamine, RS-17053, methoxamine, yohimbine, and BMY7378) by capillary electrophoresis (CE) with UV detection. Optimum separation of the analytes was obtained on a 50 cm × 75 μm i.d. capillary using a buffer containing 20% acetonitrile, 60 mM ammonium acetate, and 1.0% glacial acetic in methanol medium, with applied voltage and capillary temperature of 23 kV and 25 °C, respectively. The relative standard deviations of the migration times and the peak areas of the eight analytes were in the ranges of 0.12–1.29% and 1.02–2.53%, respectively. Detection limits of oxymetazoline, 5-methylurapidil, prazosin, phentolamine, RS-17053, methoxamine, yohimbine, and BMY7378 were 0.5–1.0 μg mL⁻¹. In the tested concentration range, good linear relationships (correlation coefficients >98%) between peak areas and concentrations of the analytes were observed. This method has been successfully applied for determination of prazosin and phentolamine with recoveries of 97.30% and 98.12%, respectively. The proposed method was successfully applied for the rapid CE determination of the frequently applied alpha-adrenergic blocking compounds phentolamine and prazosin in general pharmaceutical preparation.     

Voltammetric determination of boron by using Alizarin Red S

Cordycepin is the main active metabolite of Cordyceps militaris extracts; according to recent studies it has interesting therapeutic activities. A new capillary electrophoresis (CE) procedure with UV detection at 254 nm for determination of cordycepin was developed and optimized. Optimal conditions found were 20 mM sodium borate buffer with 28.6% methanol, pH 9.5, separation voltage 20 kV, hydrodynamic injection time 10 s and temperature 25 °C. Linearity was found over the 20-100 μg/mL concentration ranges of cordycepin. The developed method has been applied for determination of cordycepin in various pharmaceutical products. A comparison was made between CE and a high performance liquid chromatography (HPLC) method. Both of these methods gave comparable results. The shorter analysis time and low running cost are the main advantages of CE method.     

Genotyping of α-thalassemia deletions using multiplex polymerase chain reactions and gold nanoparticle-filled capillary electrophoresis

A gold nanoparticle-filled capillary electrophoresis method combined with three multiplex polymerase chain reactions (PCRs) was established for simultaneous diagnosis of five common α-thalassemia deletions, including the -α^3.7 deletion, -α^4.2 deletion, Southeast Asian (- -^SEA), Filipino (- -^FIL) and Thai (- -^THAI) deletions. Gold nanoparticles (GNPs) were used as a pseudostationary phase to improve the resolution between DNA fragments in a low-viscosity polymer. To achieve the best CE separation, several parameters were evaluated for optimizing the separation conditions, including the capillary coating, the concentrations of polymer sieving matrix, the sizes and concentrations of GNPs, the buffer concentrations, and the pH. The final CE method for separating a 200-base pair (bp) DNA ladder and α-thalassemia deletions used a DB-17 capillary, 0.6% poly(ethylene oxide) (PEO) prepared in a mixture of GNP_32nm solution and glycine buffer (25 mM, pH 9.0) (80:20, v/v) as the sieving matrix with 1 μM YO-PRO-1 for fluorescence detection; the applied voltage was −10 kV (detector at anode side) and the separation temperature was 25 °C. Under these optimal conditions, 15 DNA fragments with sizes ranging from 0.2 kb to 3.0 kb were resolved within 11.5 min. The RSDs of migration times were less than 2.81%. A total of 21 patients with α-thalassemia deletions were analyzed using this method, and all results showed good agreement with those obtained by gel electrophoresis.     

粒子群算法优化中药化学成分的毛细管电泳分离条件

建立了一种基于粒子群优化算法的毛细管电泳条件辅助优化方法。以丹参为研究对象,将改良的色谱指数方程用于评价酚酸类成分的电泳分离性能,用粒子群优化算法对分离条件进行全局寻优,获得最佳的区带电泳分离条件(5.0 mmol/L硼砂,18.5 mmol/L磷酸二氢钠,6.1%乙腈,运行电压18.2 kV)。为进一步改善分离,在所获优化条件下添加50.0 mmol/L SDS,在胶束电动毛细管色谱分离模式下使酚酸类成分(原儿茶醛、丹参素、丹酚酸B等)得到更好分离。本方法准确可靠,可推广应用于其他复杂化学体系的毛细管电泳分离条件优化。     

Quality by design-assisted development of a capillary electrophoresis method for the enantiomeric purity determination of tenofovir

A CE method was developed and validated for the assessment of the chiral purity of the drug tenofovir applying a quality by design approach. Following selection of a quaternary ammonium β-CD as chiral selector, a fractional factorial resolution V+ design was employed for identification of the critical process parameters, while a central composite design served for method optimization. The final method used a 40/50.2 cm, 50 μm id fused-silica capillary, a BGE composed of a 100 mM sodium phosphate buffer, pH 6.4, containing 45 mg/mL quaternary ammonium β-CD, an applied voltage of 18 kV, and a capillary temperature of 22°C. Robustness was assessed by a Plackett–Burman design. The method was validated according to guideline Q2(R1) of the International Council for Harmonization of Technical Requirements for Pharmaceuticals for Human Use and enabled the determination of the (S)-enantiomer of tenofovir at the 0.1% level.     

Quantitative separation of oxytocin,norfloxacin and diclofenac sodium in milk samples using capillary electrophoresis

A simple, sensitive and rapid method has been developed for simultaneous separation and quantification of three different drugs: oxytocin (OT), norfloxacin (NOR) and diclofenac (DIC) sodium in milk samples using capillary electrophoresis (CE) with UV detection at 220 nm. Factors affecting the separation were pH, concentration of buffer and applied voltage. Separation was obtained in less than 9 min with sodium tetraborate buffer of pH 10.0 and applied voltage 30 kV. The separation was carried out from uncoated fused silica capillary with effective length of 50 cm with 75 µm i.d. The carrier electrolyte gave reproducible separation with calibration plots linear over 0.15–4.0 µg/mL for OT, 5–1000 µg/mL for NOR and 3–125 µg/mL for DIC. The lower limits of detection (LOD) were found to be 50 ng/mL for OT, and 1 µg/mL for NOR and DIC. The method was validated for the analysis of drugs in milk samples and pharmaceutical preparations with recovery of drugs within the range 96–100% with RSD 0.9–2.8%. Copyright © 2009 John Wiley & Sons, Ltd.     

Determination of lipoic acid in human urine by capillary zone electrophoresis

Fast, simple, and accurate CE method enabling determination of lipoic acid (LA) in human urine has been developed and validated. LA is a disulfide‐containing natural compound absorbed from the organism's diet. Due to powerful antioxidant activity, LA has been used for prevention and treatment of various diseases and disorders, e.g. cardiovascular diseases, neurodegenerative disorders, and cancer. The proposed analytical procedure consists of liquid–liquid sample extraction, reduction of LA with tris(2‐carboxyethyl)phosphine, derivatization with 1‐benzyl‐2‐chloropyridinium bromide (BCPB) followed by field amplified sample injection stacking, capillary zone electrophoresis separation, and ultraviolet‐absorbance detection of LA‐BCPB derivative at 322 nm. Effective baseline electrophoretic separation was achieved within 6 min under the separation voltage of 20 kV (∼80 μA) using a standard fused‐silica capillary (effective length 51.5 cm, 75 μm id) and BGE consisted of 0.05 mol/L borate buffer adjusted to pH 9. The experimentally determined limit of detection for LA in urine was 1.2 μmol/L. The calibration curve obtained for LA in urine showed linearity in the range 2.5–80 μmol/L, with R ² 0.9998. The relative standard deviation of the points of the calibration curve was lower than 10%. The analytical procedure was successfully applied to analysis of real urine samples from seven healthy volunteers who received single 100 mg dose of LA.     

Rapid determination of aliphatic amines in water samples by pressure-assisted monolithic octadecylsilica capillary electrochromatography-mass spectrometry

A pressure-assisted capillary chromatography-mass spectrometry method based on the use of a monolithic octadecylsilica (ODS) capillary is proposed for the determination of aliphatic amines. A 25 mM citric acid buffer containing 10% methanol is used as running electrolyte. Separation is achieved by simultaneously applying a capillary electrophoresis (CE) voltage of 13 kV and an overimposed pressure of 8 bar. The use of pressure is required to ensure stable electrospray conditions. Analysis times are reduced by using a capillary column consisting of a 30 cm long monolithic silica capillary column bound with ODS and a fused-silica capillary column also 30 cm long. The proposed method was successfully applied to the determination of low-molecular-weight aliphatic amines in tap and river water. The analysis of real samples requires cleanup and preconcentration, which can be performed automatically by inserting a minicolumn in the replenishment system of the commercial instrument.     

Steroselective determination of trihexyphenidyl using carboxylmethyl-β-cyclodextrin by capillary electrophoresis with field-amplified sample stacking

A simple, sensitive and low-cost method using capillary electrophoresis coupled with field-amplified sample stacking (FASS) technique has been developed for enantioselective separation and quantification of trihexyphenidyl (THP) enantiomers in human serum. In this work, three kinds of modified β-cyclodextrin were tested as chiral selectors in CE. Among the CDs studied, THP enantiomers could only be separated by carboxylmethyl-β-cyclodextrin (CM-β-CD). A systematic study of the parameters (CD concentration and pH value in CE buffer, separation voltage and temperature, composition of sample solvent, injection voltage and time) affecting chiral separation and on-line concentration of THP enantiomers were investigated and optimized. The optimum FASS method provided a sensitivity enhancement of about 490-fold compared with usual hydrodynamic injection. Limits of detection for each enantiomer were in the low ng ml^− 1 concentration range (0.92 ng ml^− 1 or 3.06 nM). The quantification of each THP enantiomer in human serum was performed after serum sample extraction. To validate this CE-FASS method, linear regression analysis, intra and inter-day precision and recovery were determined with satisfying results.     

Determination of rhein and physcion in rhubarb by microchip capillary electrophoresis in mixed hydro-organic solvent combined with laser-induced fluorescence detection

Microchip capillary electrophoresis in mixed hydro-organic solvent combined with laser-induced fluorescence detection was developed for the separation and detection of physcion and rhein in rhubarb. In contrast to the conventional capillary electrophoresis method, ammonium acetate-dimethyl sulfoxide was used as the basic buffer system in this method. The effects of background buffer, buffer apparent pH*, buffer concentration, water ratio, sample preparation method, and separation voltage on separation and detection were investigated. Optimized separation and detection conditions were obtained: the buffer consisted of 20 mmol/L of ammonium acetate in hydro-organic solvent composed dimethyl sulfoxide, formamide, and water mixed at 60/20/20 (v/v/v) ratio. The separation voltage was 1.9 kV. Under these conditions, the physcion, rhein, and other components of rhubarb can be completely separated within 150 s. Under the methodological verification, good linearity (R ≥ 0.9995) for physcion and rhein, and low limits of detection (0.085 μg·mL⁻¹ and 0.077 μg·mL⁻¹, respectively), satisfactory peak area precisions, migration time precisions (1.74%–3.09%), and accuracy (recovery rate 97.8% and 101.4%) were achieved. It is shown that the proposed method is simple, efficient, fast, sensitive, simple instrument, consumes few samples, has low operating cost, and is linear.     

Simultaneous determination, by capillary zone electrophoresis, of multiple components of different industrial products

Summary Four parabens (esters of 4-hydroxybenzoic acid), effective preservatives against the growth of bacteria, yeast, and mold in numerous industrial products, have been used in this work as model compounds to demonstrate the resolving power of capillary electrophoresis (CE). The simultaneous determination of methyl-(MP), ethyl-(EP), propyl-(PP), and butylparaben (BP) was achieved by capillary zone electrophoresis (CZE) with UV diode-array detection at 294 nm. When run voltage, temperature, and electrolyte concentration and pH were optimized the most effective separation was achieved within 7 min by use of 50 cm (effective length) fused silica capillary tubing and operation at 25kV and 20°C. Background electrolyte comprising 35 mM tetraborate buffer adjusted to pH 10.0 gave the best results. The limits of detection of the optimized method ranged from 0.65 μg mL⁻¹ for BP to 0.81 μg mL⁻¹ for MP; the relative standard deviation was between 0.35 and 0.50%. These results showed that the method enables the determination of the four parabens in commerially available cosmetic and pharmaceutical preparations containing some of the parabens and in an unidentified canned berry fruit juice.     

Efficient sample clean‐up and online preconcentration for sensitive determination of melamine in milk samples by capillary electrophoresis with contactless conductivity detection

Based on an efficient sample clean‐up and field‐amplified sample injection online preconcentration technique in capillary electrophoresis with contactless conductivity detection, a new analytical method for the sensitive determination of melamine in milk samples was established. In order to remove the complex matrix interference, which resulted in a serious problem during field‐amplified sample injection, liquid–liquid extraction was utilized. As a result, liquid–liquid extraction provides excellent sample clean‐up efficiency when ethyl acetate was used as organic extraction by adjusting the pH of the sample solution to 9.5. Both inorganic salts and biological macromolecules are effectively removed by liquid–liquid extraction. The sample clean‐up procedure, capillary electrophoresis separation parameters and field‐amplified sample injection conditions are discussed in detail. The capillary electrophoresis separation was achieved within 5 min under the following conditions: an uncoated fused‐silica capillary, 12 mM HAc + 10 mM NaAc (pH = 4.6) as running buffer, separation voltage of +13 kV, electrokinetic injection of +12 kV × 10 s. Preliminary validation of the method performance with spiked melamine provided recoveries >90%, with limits of detection and quantification of 0.015 and 0.050 mg/kg, respectively. The relative standard deviations of intra‐ and inter‐day were below 6%. This newly developed method is sensitive and cost effective, therefore, suitable for screening of melamine contamination in milk products.     

A gravity-independent single-phase electrode reservoir for capillary electrophoresis applications

Capillary electrophoresis (CE) holds great promise as an in situ analytical technique for a variety of applications. However, typical instrumentation operates with open reservoirs (e.g., vials) to accommodate reagents and samples, which is problematic for automated instruments designed for space or underwater applications that may be operated in various orientations. Microgravity conditions add an additional challenge due to the unpredictable position of the headspace (air layer above the liquid) in any two-phase reservoir. One potential solution for these applications is to use a headspace-free, flow-through reservoir design that is sealed and connected to the necessary reagents and samples. Here, we demonstrate a flow-through high-voltage (HV) reservoir for CE that is compatible with automated in situ exploration needs, and which can be electrically isolated from its source fluidics (in order to prevent unwanted leakage current). We also demonstrate how the overall system can be rationally designed based on the operational parameters for CE to prevent electrolysis products generated at the electrode from entering the capillary and interfering with the CE separation. A reservoir was demonstrated with a 19 mm long, 1.8 mm inner diameter channel connecting the separation capillary and the HV electrode. Tests of these reservoirs integrated into a CE system show reproducible CE system operation with a variety of background electrolytes at voltages up to 25 kV. Rotation of the reservoirs, and the system, showed that their performance was independent of the direction of the gravity vector.     

Pressure‐assisted capillary electrophoresis frontal analysis for faster binding constant determination

Adding external pressure during the process of capillary electrophoresis usually add to the band broadening, especially if the pressure induced flow is significant. The resolution is normally negatively affected in pressure‐assisted capillary electrophoresis (PACE). Frontal analysis (FA), however, can potentially benefit from using an external pressure while avoiding the drawbacks in other modes of CE. In this work, possible impact from the external pressure was simulated by COMSOL Multiphysics®. Under a typical CE‐FA set‐up, it was found that the detected concentrations of analyte will not be significantly affected by an external pressure less than 5 psi. Besides, the measured ligand concentration in PACE‐FA was also not affected by common variables (molecular diffusion coefficient (10⁻⁸ to 10⁻¹¹ m²/s), capillary length etc). To provide an experimental proof, PACE‐FA is used to study the binding interactions between hydroxypropyl β‐cyclodextrin (HP‐β‐CD) and small ligand molecules. Taking the HP‐β‐CD /benzoate pair as an example, the binding constants determined by CE‐FA (18.3 ± 0.8 M⁻¹) and PACE‐FA (16.5 ± 0.5 M⁻¹) are found to be similar. Based on the experimental results, it is concluded that PACE‐FA can reduce the time of binding analysis while maintaining the accuracy of the measurements.     

Simultaneous determination of atenolol and amiloride in pharmaceutical preparations by capillary zone electrophoresis with capacitively coupled contactless conductivity detection

Capillary zone electrophoresis coupled with a capacitively coupled contactless conductivity detector (CE‐C⁴D) has been employed for the determination of atenolol and amiloride in pharmaceutical formulations. Acetic acid (150 mm ) was used as background electrolyte. The influence of several factors (detector excitation voltage and frequency, buffer concentration, applied voltage, capillary temperature and injection time) was studied. Non‐UV‐absorbing L‐valine was used as internal standard; the analytes were all separated in less than 7 min. The separation was carried out in normal polarity mode at 28°C, 25 kV and using hydrodynamic injection (25 s). The separation was effected in an uncoated fused‐silica capillary (75 μm, i.d. × 52 cm). The CE‐C⁴D method was validated with respect to linearity, limit of detection and quantification, accuracy, precision and selectivity. Calibration curves were linear over the range 5–250 μg/mL for the studied analytes. The relative standard deviations of intra‐ and inter‐day migration times and corrected peak areas were less than 6.0%. The method showed good precision and accuracy and was successfully applied to the simultaneous determination of atenolol and amiloride in different pharmaceutical tablet formulations. Copyright © 2010 John Wiley & Sons, Ltd.     

Simultaneous determination of flavonoids in chrysanthemum by capillary zone electrophoresis with running buffer modifiers

Despite the separation efficiency of capillary electrophoresis (CE) is much higher than other chromatographic methods, it is sometimes difficult to perfectly separate the complex ingredients in biological samples. One possible and simple way to develop the separation effect in CE is to add some modifiers in the running buffer. In this paper, the suitable running buffer modifiers were explored to simultaneously separate and detect six typical flavonoids (apigenin, luteolin, kaempferol, quercetin, (+)-catechin and (−)-epicatechin) which are the main active ingredients in chrysanthemum by capillary zone electrophoresis with amperometric detection (CZE-AD). It was found that when β-cyclodextrin (β-CD) and the mixture of methanol and ethanol were used as running buffer modifiers, a baseline separation of the six analytes could be accomplished in less than 20 min and the detection limits were as low as 10⁻⁷ or 10⁻⁸ g ml⁻¹. Other factors affecting the CZE separation, such as working potential, pH value and ionic strength of running buffer, separation voltage and sample injection time were extensively investigated. Under the optimum conditions, a successful practical application on the determination of chrysanthemum samples confirmed the validity and practicability of this method.     

Simultaneous determination of DTPA,EDTA, and NTA by capillary electrophoresis after complexation with copper

We present a method for simultaneous determination of the aminopolycarboxylic acids DTPA, EDTA and NTA in dishwashing detergents, paper mill waters, and natural waters by capillary electrophoresis (CE). The complexing agents were examined as their copper(II) complexes and separated by conventional CE with reversed polarity of the applied voltage. The optimum separation conditions were established by varying the pH and phosphate and tetradecyltrimethylammonium bromide (TTAB) concentrations in the run buffer. The separations were carried out in a fused-silica capillary (61 cm×75 m i.d.) filled with phosphate buffer (80 mmol L^–1, TTAB concentration 0.5 mmol L^–1, pH 7.1, voltage –20 kV) using direct UV detection at 191 and 254 nm. With this CE method all the peaks in the electropherograms were properly separated, the calibration plots gave good correlation coefficients and all three complexing agents could be detected in less than 4 min. Linear calibration plots were obtained for CuDTPA, CuEDTA and CuNTA; limits of detection were 0.03 mmol L^–1 for all complexing agents and recoveries for all tested samples were within the range 104±7%. Results obtained from dishwashing detergent samples were found to be reliable and comparable with those from HPLC (R²=0.989) and UV–Vis (R²=0.985) methods.